Generac 1403-0 User Manual
This symbol points out important safety instructions, which, if not followed, could endanger the personal safety and/or
property of yourself and others. Read and follow all instructions in the manual before attempting to operate this unit.
Model No. 1403-0 Power Transfer System Manual No. B4610 (Revision 2, 1/28/2000)
GENERAC
Portable Generator
Power Transfer System with Dual Load Manager
™
Owner’s Manual
Problems?
Questions?
Before taking your system
back to the store,
call the generator
helpline at
18002701408
MF 85 CT
DESCRIPTION
The Model 1403 Power Transfer System safely connects up to twelve essential household loads, such as the
furnace fan, freezer, refrigerator, water well pump, sump pump, lighting or outlet circuits to either the utility power
or a portable generator. In the event of a utility power failure, the homeowner can safely select devices to be
powered by an outdoor portable generator. Self-contained load meters assist the operator when managing power
loads. The power transfer system will not permit connection to both utility and generator power at the same time.
The Model 1403 Power Transfer System is easy for a licensed electrician or qualified professional to install, safe
for a homeowner to operate, and will work with 240 Volt AC generators factory equipped with a NEMA type
14-50R receptacle.
This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE.
IMPORTANT
This product must be installed in compliance with local residential wiring and electrical codes by a
licensed electrician or qualified professional. Generac Portable Products is not responsible for
damaged equipment, accidents, or personal injury caused by incorrect installation.
Read this Safety Manual and Instructions BEFORE operating Power Transfer System.
CONTENTS:
Installation Instructions - - - - - - - - - - - -Page 1 through 12
Owners Operating Procedure - - - - - -Page 13 through 16
Generac Portable Products Power Transfer System
2
NOTE: The maximum load allowed through each
Load Manager switch is 7200 Watts: 30 Amps at
240 Volts or 60 Amps at 120 Volts.
Per National Electric Code, connection of a
generator to any electrical circuit normally
powered by an electric utility must be by means
of approved transfer switch equipment so as to
isolate the electrical circuit from the utility
distribution system when the generator is
operating. Failure to isolate the electrical circuits
by such means may result in injury or death to
utility power workers due to backfeed of
electrical energy.
CAUTION: Each Load Manager switch is for
indoor use only. The connection box is a NEMA
type 3R, intended for outdoor use.
NEMA stands for National Electrical Manufacturers Association.
GENERATOR
COMPATIBILITY
Only use a generator that is
factory-equipped with a NEMA
Type 14-50R receptacle.
NEVER use a generator equipped
with a 3-prong 240 Volt receptacle
because damage may occur in
connected appliances.
CARTON CONTENTS
Items in the shipping carton include:
Two Load Manager Switches
Connecting Box
Connecting Cord Set
50 Amp Connecting Plug
Attention Decal
If any of the above parts are missing or damaged, call
the Generac helpline at 18002701408.
UNPACKING
Remove the Power Transfer System components from
the shipping carton. Each Load Manager switch is
completely prewired and ready for installation. Inspect
the switches and attached wires and flexible conduit
for any shipping damage.
The connection box is supplied ready to be wired.
Inspect the box, the connection cord set, and the
connecting plug for any damage.
The installer will select and attach the connecting cord
plug, as described in the Installation Procedure,
step 22.
Items Not Shipped with Power Transfer System:
The following items, required for system installation,
are not included and must be provided by the installer:
1. Tools required for installation
2. Anchors and screws to mount the power transfer
system components and conduit.
3. Junction box(s), conduit, fittings, wire nuts, and
insulated copper wire for connecting the Load
Manager switches to the outside connection box.
SPECIFICATIONS
Model Number.......................................................1403
Maximum Circuits......................................................12
Maximum Load/Circuit from Generator ...........15 Amps
Maximum Load/Circuit from Load Center .......20 Amps
Maximum Watts per Load Manager...................7200
Connecting Cord Length .........................................8 ft.
Generac Portable Products Power Transfer System
3
GENERAL SAFETY
INFORMATION
1. A licensed electrician or qualified professional
(referred to herein as installer) must install
the power transfer system per local code.
2. During installation, the installer is required to
remove the cover from the building power
distribution panel (referred to herein as a load
center.) To reduce the risk of electrical shock, the
Main circuit breaker must be turned OFF while the
load center cover is removed.
3. DO NOT OVERLOAD THE GENERATOR.
Overloading a generator in excess of its rated
wattage capacity will trip generator circuit
breakers.
4. Always plug the connecting cord set into the
connection box and generator BEFORE starting
the generator. Always shut the generator down
before detaching the cord set.
5. Portable generators attached to this Power
Transfer System must be operated outside, in
accordance with warnings and instructions found in
the generators Owners Manual.
PLAN THE INSTALLATION
The installer and the homeowner decide which circuits
are to be powered by the generator during a utility
power outage:
The plan should ensure that no single circuit load
exceeds 15 Amps.
The plan should also identify circuits that exceed the
15 Amp maximum.
During generator operation, the homeowner should
use only necessary household items and to alternate
use of larger loads, such as water pump or electric
skillet. The installer will instruct the homeowner in
appropriate load management techniques.
Three methods of determining loads are given here:
Measure Actual Loads
The installer uses a clamp-on ammeter to measure
each of the actual desired loads to ensure each total
circuit draws less than 15 Amps.
Sum Loads from Data Plates
The installer inspects each desired device, notes
current consumption found on labels on each
appliance, then adds all loads on each circuit:
The rated current of appliances and motors can
usually be found on a data plate or decal affixed to
the device.
The rated wattage of lights can be taken from light
bulbs.
Some electric motors, such as induction types,
require about three times more power for starting
than for running. This surge of power lasts for only a
few seconds when starting such motors. Be sure to
allow for this high starting load.
Estimate Loads
The third method estimates total circuit loads based on
information given in Figure 1.
APPLIANCE ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~LOAD DRAW
Air Conditioner (12,000 BTU) ~ ~ ~ ~ ~(1700W) 7A@240V
Coffee Maker ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~(1000W) 8.4A@120V
*Electric Range (one element) ~ ~ ~(1500W) 6.3A@240V
Electric Blanket ~ ~ ~ ~ ~ ~ ~ ~ ~ ~(1500W) 12.5A@120V
Electric Skillet ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~(1250W) 10.5A@120V
*Freezer ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~(500W) 4.2A@120V
*Furnace Fan (1/3 HP) ~ ~ ~ ~ ~ ~ ~(1200W) 10A@120V
*Jet Pump ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~(800W) 3.4A@240V
Light Bulb ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~(100W) 0.9A@120V
Microwave Oven ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~(700W) 5.9A@120V
Oil Burner on Furnace ~ ~ ~ ~ ~ ~ ~ ~(300W) 2.5A@120V
Oil Fired Heater (30,000 BTU) ~ ~ ~ ~(150W) 1.3A@120V
Oil Fired Heater (85,000 BTU) ~ ~ ~ ~(225W) 1.9A@120V
Oil Fired Heater (140,000 BTU) ~ ~ ~(400W) 3.4A@120V
Radio ~ ~ ~ ~ ~ ~ ~ ~ ~ ~(50 to 200W) 0.5 to 1.7A@120V
*Refrigerator ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~(600W) 5A@120V
*Submersible Well Pump (1 HP) ~ ~(2000W) 8.4A@240V
Sump Pump ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~(600W) 5A@120V
Television ~ ~ ~ ~ ~ ~ ~ ~(200 to 500W) 1.7 to 4.2A@120V
* Allow 3 times the listed watts for starting these devices.
WATTS = AMPS x VOLTS
Figure 1 Load Reference Guide
Generac Portable Products Power Transfer System
4
INSTALLATION
PROCEDURE
Load Manager Switch
Before removing the load center cover, plan mounting
location for both Load Manager switches. To do so,
hold a Load Manager switch about 18 inches from
the center of the load center, as shown in Figure 2.
NOTE: The following procedure describes the
installation of one Load Manager switch. Use
identical instructions to install and test the second
Load Manager switch.
1. Ensure there is enough room to mount both Load
Manager switches so their flex conduit attaches
directly to the load center.
2. Identify appropriate vacant load center 3/4
knockouts.
DANGER: Contact with wires and terminals
inside the load center must be avoided as
contact may result in dangerous electrical
shock. Before removing the load center cover,
switch OFF the main circuit breaker serving the
load center. Remember that wires on the line
side of the main circuit breaker are electrically
dangerous.
3. Turn OFF the load centers main circuit breaker,
then remove the load center cover.
4. Remove the predetermined knockouts. Route all
wires extending from the flexible conduit attached
to a Load Manager switch through the empty
hole, as shown in Figure 3. Secure the conduit
connector to the load center with the supplied lock
nut.
5. Anchor the Load Manager switch to the wall at
the selected position, as shown in Figure 4.
Figure 2 Planning Switch Location
Figure 3 Wire Loom from Switch
Figure 4 Anchoring Load Manager Switch
Generac Portable Products Power Transfer System
5
6. From the load management plan, determine the
load that is to be connected to Load Manager
switch circuit A. Turn that load center circuit
breaker to its OFF position. Loosen the screw
that retains the wire to this breaker, then detach
the wire. Figure 5 shows the selected load wire
detached from the circuit breaker.
7. Find the black and red wires marked A that come
from the Load Manager switch. Using good
workmanship, route both of these wires near the
selected circuit breaker. Trim and strip the red A
wire and install it properly into the circuit breaker.
8. Trim and strip the black A wire to mate with the
wire previously detached from the breaker. Secure
the wire ends with a wire nut. Neatly dress the
wires into the load center, as shown in Figure 6.
IMPORTANT:The installer should never cross the
black and red leads from the Load Manager switch.
Doing so will void the warranty and could cause
significant damage to Load Manager components
and the generator.
Make Sure:
The RED wire from the Load Manager switch is
always connected to the circuit breaker.
The BLACK wire from the Load Manager switch is
always connected to the wire going to the load.
DANGER! You must connect the Load
Manager switch wires as described or serious
damage to the equipment or yourself may result.
9. Select the load center circuit that will become load
management circuit B. Repeat Steps 6 through 8
for the red and black wires marked B coming
from the Load Manager switch.
10. If you wish to connect a 240 Volt AC two-pole
circuit, such as a well pump, proceed as follows:
a. Turn off the two-pole circuit breaker used for
the pump circuit and detach the load wires
from that breaker.
b. Select the four wires marked C and D
coming from the Load Manager switch
conduit and route them close to the selected
circuit breaker(s).
c. Repeat Steps 6 through 8 for each pair of red
and black wires C and D.
d. A typical two-pole circuit connection is shown
in simplified form in Figure 7.
Figure 7 Two-pole Connection
Figure 5 Wire Detached From Breaker
Wire removed
Figure 6 Single-pole Connection
Loading...