Genelec 7260A, 7270A, 7271A Owner's Manual

dsp

Operating Manual

7260A, 7270A and 7271A DSP Subwoofers

2

3

INTRODUCTION

Congratulations and a thank-you for the purchase of this Genelec 7200 Series DSP Subwoofer. These
systems are designed to integrate easily into the digital production environment. There are several ways
to configure and operate the DSP subwoofers for a wide variety of high quality audio applications.

This manual addresses setting up and using the Genelec 7260A, 7270A and 7271A subwoofers with
Genelec 8240A and 8250A DSP loudspeakers in stand-alone mode without the Genelec Loudspeaker
Manager GLM™ and the proprietary Genelec loudspeaker control network. Use with the GLM™ network
is described in the DSP System Operating Manual.

EC Declaration Of Conformity

This is to certify that Genelec 7260A, 7270A and 7271A DSP subwoofers conform to the following
standards:

Safety: EN 60065: 2002 / IEC 60065:2001 7th Edition
EMC: EN 55020 : 2002 + A1 : 2003, EN 55013: (2001), EN 61000-3-2 (2000) and EN 61000-3-3 (1995)

The products herewith comply with the requirements of The Low Voltage Directive 73/23/EEC, EMC
Directive 89/336/EEC and 93/68/EEC

Signed:
Ilpo Martikainen
Position: Chairman of the Board
Date: 20-February-2006

Compliance to FCC Rules

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interference that may cause
undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

4

harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

• Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user’s authority to operate the
equipment under FCC rules.

SYSTEM

Genelec 7260A, 7270A and 7271A DSP subwoofers

are designed for precise monitoring of 24 bit/192

kHz AES/EBU digital audio signal. They are fully compatible with

Genelec Loudspeaker Manager
GLM™ and the proprietary Genelec loudspeaker control network and Genelec 8240A and 8250A DSP
loudspeakers

.

The DSP subwoofers can perform bass management. The DSP bass management system splits the signal
from each input into low and high frequency components. Signal content below the crossover frequency
is reproduced by the subwoofer and signal content above the crossover frequency is reproduced by the
loudspeakers connected to the outputs of the subwoofer.

USING THE 7260A, 7270A AND 7271A IN STAND-ALONE MODE

When the subwoofers are not connected to the Genelec loudspeaker control network, they operate in
stand-alone mode and only the functions actuated by the controls on the connector panel can be used.
However, the settings made with the Genelec Loudspeaker Manager software can be saved into each
subwoofer and applied even when the network is disconnected by setting

switch 1 “STORED/MANUAL

CONTROL” on switch group 2 of each loudspeaker to position “STORED.”

This manual concentrates on using the subwoofers without the control network. All issues concerning the
control network are explained in detail in the System Operating Manual provided with the GLM™ Genelec
Loudspeaker Manager kit.

5

INSTALLATION

Each subwoofer is supplied with a mains cable

, one 5 m GLM network cable and

an operating manual. Once

unpacked, place the subwoofer in a suitable location (for more details see the "Positioning" section).

Before connecting the audio signal cables, ensure that both the subwoofer and the main loudspeakers
are switched off. Connections are easier to make if you roll the subwoofer on its side with the connector
panel facing up. Use this position only for making the connections and roll the subwoofer back to its
normal upright position before use.

Connections

Audio connections

Audio connections to the subwoofer are made by XLR connectors. All audio cabling from the source must
always go first to the input connectors of the subwoofer and then on to the main loudspeakers from the
subwoofer’s output connectors. Some typical setups are shown in “Cabling examples” below.

Connect the digital audio signal cables from your signal source to the four female XLR “AES/EBU INPUT”
connectors. The inputs accept AES/EBU signal or S/P-DIF or AES3id signals with suitable impedance
converters. Both Single-Wire and Dual-Wire AES/EBU formats are automatically detected and supported.
The 7260A, 7270A and 7271A cannot be used with analog audio input signal. If the chosen audio format
includes an LFE (.1) channel, it must be connected to INPUT 4 and the “LFE IN USE” switch must be
turned to “YES” position in order to utilize the versatile LFE channel controls integrated in the subwoofer.
If there is no LFE channel to reproduce, INPUT 4 can be used for a normal full-bandwidth signal. In this
case the “LFE IN USE” switch must be turned to “NO”

Connect the signal cables for the main loudspeakers to the male “AES/EBU OUTPUT” connectors on
the subwoofer. Each of these connectors carries a high-pass filtered version of the signal(s) received by
the input connector marked with the same number. The default filtering frequency is 85 Hz. The filtering
frequency cannot be changed with the controls available in the stand-alone mode. This feature is only
available when the subwoofer is controlled by the GLM™ software.

Network, mains, bypass and remote connectors

Two “CONTROL NETWORK” RJ-45 sockets are provided to connect the subwoofer to the proprietary
Genelec loudspeaker control network. See the System Operating Manual for more information. The
mains cable may only be connected to an earthed mains power supply. The “BYPASS” 1/4” Jack provides
connection to the optional Genelec 1092-400 switch to operate the Bypass function. See “DSP Subwoofer
Features” for description of this function.

6

Cable number Subframe Audio

channel

Subwoofer Input
Connector

Loudspeaker
Input Connector

1 A Left AES/EBU INPUT 1 DIGITAL IN

1 B Right AES/EBU INPUT 1 DIGITAL IN

Cabling examples

Stereo Pair with Subwoofer (AES/EBU Single-Wire)

This setup has one AES/EBU cable that carries both the Left and Right audio channels with subframe A
carrying the Left audio channel and subframe B carrying the Right audio channel.

Run one AES/EBU cable from the source to one of the subwoofer’s “INPUT” connectors, then from the
corresponding “OUTPUT” connector to the “DIGITAL IN” connectors on the Left and Right loudspeakers
(the order of cabling to the loudspeakers is irrelevant). The correct subframe must be selected in each
loudspeaker.

The “REMOTE” RJ 11 connector can be used to connect the optional Remote Power/OVL LED (Genelec
7000-415) or 7000-416 Remote control switch for "Bypass" and "+10 dB LFE" functions.

7

Cable number Subframe Audio channel Subwoofer Input

Connector

Loudspeaker
Input Connector

1 A Left Front AES/EBU INPUT 1 DIGITAL IN

1 B Right Front AES/EBU INPUT 1 DIGITAL IN

2 A Left Rear AES/EBU INPUT 2 DIGITAL IN

2 B Right Rear AES/EBU INPUT 2 DIGITAL IN

3 A Center Front AES/EBU INPUT 4 DIGITAL IN

3 B LFE AES/EBU INPUT 4 --

5.1 Surround System with Subwoofer (AES/EBU Single-Wire)

This setup utilizes three AES/EBU cables to carry 5.1-audio. “5.1” refers to having five full-bandwidth
audio channels and an LFE channel. All three cables run to the subwoofer first, then from the subwoofer
to the five main loudspeakers.

The AES/EBU digital audio cables are numbered from one to three. The AES/EBU subframe assignments
and connectors to be used with the subwoofer and loudspeakers are provided in the table below.

Run three AES/EBU cables from the source to the subwoofer AES/EBU inputs 1, 2 and 4. Subwoofer
input number 3 is not used. Run the cables from the subwoofer AES/EBU outputs 1, 2 and 4 to the

digital
audio inputs of the loudspeakers. The cable that carries the LFE channel must be connected to the
subwoofer input number 4. The correct subframe must be selected in each loudspeaker.

8

6.1 Surround System with Subwoofer (AES/EBU Single-Wire)

This setup utilizes four AES/EBU cables to carry “6.1-audio”. “6.1” refers to having six full-bandwidth
audio channels and an LFE channel. All cables run to the subwoofer first, then from the subwoofer to the
six loudspeakers.

The AES/EBU digital audio cables are numbered one to four. The AES/EBU subframe assignments and
connectors to be used with the subwoofer and two-way loudspeakers are provided in the table below. The
correct subframe must be selected in each loudspeaker.

Cable number Subframe Audio channel Subwoofer Input

Connector

Loudspeaker
Input Connector

1 A Left Front AES/EBU INPUT 1 DIGITAL IN

1 B Right Front AES/EBU INPUT1 DIGITAL IN

2 A Left Rear AES/EBU INPUT 2 DIGITAL IN

2 B Right Rear AES/EBU INPUT 2 DIGITAL IN

3 A Center Rear AES/EBU INPUT 3 DIGITAL IN

3 B Not used Not used --

4 A Center Front AES/EBU INPUT 4 DIGITAL IN

4 B LFE AES/EBU INPUT 4 --

9

Run four AES/EBU cables from the source to the subwoofer AES/EBU inputs 1, 2, 3 and 4. Run the
cables from the subwoofer AES/EBU outputs 1, 2, 3

and 4 to the digital audio inputs of the loudspeakers.

The cable that carries the LFE channel must be connected to the subwoofer input number 4.

7.1 Surround System with Subwoofer (AES/EBU Single-Wire)

This setup uses four AES/EBU cables to carry “7.1-audio”. “7.1” refers to seven full-bandwidth audio
channels and an LFE channel. All cables run to the subwoofer first, then from the subwoofer to the seven
loudspeakers. In this system there are five loudspeakers in the front (Left Front, Center Front, Right
Front, Left Front Extra, and Right Front Extra), two loudspeakers in the rear (Left Rear and Right Rear),
and the LFE Low Frequency Effects channel reproduced by the subwoofer. The AES/EBU digital audio
cables are numbered one to four. The AES/EBU subframe assignments and connectors to be used with
the subwoofer and loudspeakers are provided in the table below. The correct subframe must be selected
in each loudspeaker.

Cable number Subframe Audio channel Subwoofer Input

Connector

Loudspeaker
Input Connector

1 A Left Front AES/EBU INPUT 1 DIGITAL IN

1 B Right Front AES/EBU INPUT 1 DIGITAL IN

2 A Left Rear AES/EBU INPUT 2 DIGITAL IN

2 B Right Rear AES/EBU INPUT 2 DIGITAL IN

3 A Left Front Extra AES/EBU INPUT 3 DIGITAL IN

3 B Right Front Extra AES/EBU INPUT 3 DIGITAL IN

4 A Center Front AES/EBU INPUT 4 DIGITAL IN

4 B LFE AES/EBU INPUT 4 --

10

Stereo Pair with a Subwoofer (AES/EBU Dual-Wire)

This setup has two AES/EBU cables. Each carries one audio channel.

This mode assumes the source uses the Dual-wire mode of transmission. In this mode the AES/EBU
interface is operating at double speed (96 kHz) but consecutive audio samples use both subframes,
resulting in quad sample rate (192 kHz).

Run two AES/EBU cables from the source to the subwoofer AES/EBU Inputs 1 and 2. Run two audio
cables from the subwoofer AES/EBU outputs 1 and 2 to the

digital audio inputs of the left and right

loudspeakers. The correct subframe must be selected in each loudspeaker.

Cable number Subframe Audio channel Subwoofer Input

Connector

Loudspeaker
Input Connector

1 A+B Left AES/EBU INPUT 1 DIGITAL IN

2 A+B Right AES/EBU INPUT 2 DIGITAL IN

11

5.1 Surround System with Subwoofer (AES/EBU Dual-Wire)

This setup supports six digital audio cables. The six cables customarily carry the Left, Center and Right
Front channels and the Left and Right Rear channels and the LFE. The rear channels are not bass
managed.

This mode assumes the source uses the Dual-wire mode of transmission. In this mode the AES/EBU
interface is operating at double speed (96 kHz) but consecutive audio samples use both subframes
resulting in quad sample rate (192 kHz).

Cable number Subframe 5.1 system audio

channel

Subwoofer Input
Connector

Loudspeaker
Input Connector

1 A+B Left Front AES/EBU INPUT 1 DIGITAL IN

2 A+B Right Front AES/EBU INPUT 2 DIGITAL IN

3 A+B Left Rear -- DIGITAL IN

4 A+B Right Rear -- DIGITAL IN

5 A+B Center Front AES/EBU INPUT 3 DIGITAL IN

6 A+B LFE AES/EBU INPUT 4 DIGITAL IN

12

Positioning the subwoofer in the room

The placement of the subwoofer in the room affects the overall frequency response and sound level of
the system dramatically, as at low frequencies the effects of the room are strong. Even a slight change in
the subwoofer's location can make a marked difference in the frequency balance and often patient and
methodical experimentation and testing is needed to find the optimum placement.

The placement will affect the phase difference between the main loudspeakers and the subwoofer, and
also the bass roll-off rate. These effects can be compensated by the use of the Tone and Phase controls
on the subwoofer; but we recommend that at first you leave the controls untouched and concentrate on
finding the position where the subwoofer gives the smoothest response, and only then use them to fine­tune the balance and phase alignment between the subwoofer and the main loudspeakers.

To begin, place the subwoofer at the front wall slightly offset from the center. The recommended distance
to the wall is less than 60 cm / 24" measured from the subwoofer's driver. This position gives increased
acoustic loading (and SPL) due to the proximity of the front wall and floor. Cancellations from the front wall
and floor are also avoided. Front wall cancellation for the 85 Hz high pass filtered main loudspeakers can
be eliminated by placing them at least 110 cm / 43" away from the front wall. In a multichannel system the
main loudspeakers should ideally be positioned symmetrically and at an equal distance from the listening
position.

13

If the frequency balance is not right, try moving the subwoofer slightly to the left or right so that different
room modes are excited at different levels. Positioning the subwoofer close to a corner will boost the bass
level at lower frequencies and may cause asymmetrical spatial imaging. If you are using two subwoofers,
try placing them asymmetrically relative to the side walls. Sometimes moving the subwoofers apart into the
front corners helps with problematic rear wall reflections and the loss of mutual coupling is compensated
by the bass boost caused by corner positioning.

Although the 7260A, 7270A and 7271A subwoofers are magnetically shielded, they may cause some
picture distortion if placed near to very sensitive video monitors or computer displays. Move the subwoofer
further away or try turning the driver side of the subwoofer away from the screen.

Minimum clearances to walls or other objects

The power amplifiers are attached to the lower part of the aluminium grille functioning as a heatsink. Do
not cover the grille or place the subwoofer so that there is less than 10 centimeters (4") of free space in
front of the grille.

The space adjacent to the subwoofer must either be ventilated or sufficiently large to

dissipate heat so that the ambient temperature does not rise above 35 degrees Celsius (95°F).

Make sure that the space underneath the subwoofer is clear from obstructions. Thick carpets may block
the ventilation clearance needed for cooling the electronics box. The reflex port side (opposite of the
connector panel side) should always have a clearance of at least 7,5 centimeters (3") to any objects to
ensure proper functioning of the reflex port.

Flush mounting the subwoofer

If the subwoofer is flush mounted into a wall or a cabinet, it is important to ensure unrestricted airflow
from the reflex port and amplifier cooling. This can be done by making the recess 7,5 centimeters (3")
wider than the subwoofer. Place the subwoofer into the right end of the recess with the driver side facing
the room. This leaves sufficient 7,5 centimeters (3") of free space on the reflex port side. The height and
depth of the recess should not be any bigger than those needed to fit the subwoofer flush with the wall
surface.

14

DSP SUBWOOFERS FEATURES

Various controls and switches are accessible on the DSP subwoofer control panel. Let us define and
explain here their use and function (from left to right):

LFE INPUT 4 CONTROLS

LFE in Use

When producing audio content in multichannel audio formats, the use
of the LFE channel is directly linked to the media release format and the
type of production. If in use, the LFE or (.1) channel must be connected
to AES/EBU INPUT 4 and the ‘LFE IN USE’ switch must be set to YES
position. If no LFE signal is used, the ‘LFE IN USE’ switch should be set
to NO position. The LFE input (AES/EBU INPUT 4) then operates in the
same way as the other inputs.

When a dual-wire signal is connected, the input changes to dual-wire
mode. In dual-wire mode there is only one channel per cable. If the LFE
signal is connected to INPUT 4 and the LFE signal is a dual-wire signal,
then the AES/EBU CHANNEL” setting (see below) is ignored

15

AES/EBU Channel

An AES/EBU signal normally carries two audio channels in what are called subframes A and B. The “AES/
EBU CHANNEL” switch selects if the LFE signal is designated to subframe A or B.

LFE Bandwidth

The LFE input can be set to two frequency ranges: 19 to 85 Hz or 19 to 120 Hz using the “LFE BANDWIDTH”
switch. Signal content in the LFE signal above the frequency value selected on the “LFE BANDWIDTH”
switch is either not reproduced or is redirected (see below). See also “Typical applications of different LFE
bandwidth settings” below.

Redirect

Using redirection allows the LFE channel to be monitored as a full-bandwidth audio channel. If the LFE
signal includes content higher than 120 Hz, it can be monitored using the “Redirect” function. This function
allows rerouting of LFE signal above 85 Hz to the front center loudspeaker. This rerouted LFE content is
known as the redirected LFE signal.

Setting the “REDIRECT” switch to the “ON” position activates the redirect function and it can only be
activated if the “LFE BANDWIDTH” switch is set to “85”.

The redirected LFE signal is added to the audio signal contained in the other subframe of the AES/EBU
audio cable connected to INPUT 4. Typically the LFE channel is paired with the Front Center channel, so
one of the subframes of OUTPUT 4 carries the sum of the redirected LFE signal and the center channel
signal. OUTPUT 4 should then be connected to the Front Center loudspeaker.

Subwoofer input 4 Subwoofer output 4

Subframe A Subframe B Subframe A Subframe B

Center signal LFE signal Center + redirected LFE

signal

LFE signal Center signal Center + redirected LFE

signal

LFE +10 dB

In Dolby Digital and DTS encoding formats the LFE channel is monitored with +10 dB gain relative to the
main channels. The object is to increase the headroom in the recorded signals. Surround sound decoders
may automatically add +10 dB of LFE gain to restore the level balance.

The “LFE +10 dB” function of the DSP subwoofers is designed to add the +10 dB of gain to the LFE
channel in the production stage if it is not already done by the source connected to the monitoring system,

16

Switching the “LFE +10 dB” switch to the “ON” position or using the optional remote control activates the
function. A yellow light next to the “LFE +10 dB” switch illuminates when the “LFE +10 dB” function is
activated and +10 dB of gain is added to the LFE signal. If the audio source outputs the LFE signal at the
same level as the other (non-LFE) signals and the LFE should be reproduced at a 10 dB higher level, set
this control to “ON”. If the LFE output is at a 10 dB higher level than other (non-LFE) channels, this switch
should be set to “OFF”.

The “LFE +10 dB” function should not be used in the following cases:

• If the +10 dB LFE gain is already implemented by another device, for example, a DVD player,
surround sound processor or the output matrix of a mixing console

• When producing an audio format that does not require the use of +10 dB gain on the LFE
channel, such as DVD-Audio (MLP) and SACD (DSD).

More than one subwoofer can be used to reproduce the same audio channels by connecting subwoofers
in a chain using additional signal cables. This is called “daisy-chaining”. When daisy-chaining subwoofers
the switches in the “LFE INPUT 4 CONTROLS” group must be the same for all the subwoofers in the
daisy-chain.

Bypass

The “BYPASS” section allows the use of an optional Genelec 1092-400 remote bypass
switch. This allows for remote control of the subwoofer’s bass management bypass
function. The red “BYPASS” light is illuminated when the bypass mode is active.

With the bypass mode on, the high pass filters for the loudspeakers are disabled and the
system behaves as if the subwoofer was not connected. The bypass function has no effect
on the LFE signal. If there is no LFE signal, the subwoofer will not reproduce any signal
when the bypass is active.

MODE

The “MODE” switch allows joining together two or more subwoofers to reproduce the same audio
channels at an increased sound pressure level. This is called daisy-chaining subwoofers.

When daisy-chaining two or more subwoofers, the audio channels are connected to the first
subwoofer in the chain and the “MODE” switch is set to “PASS THROUGH”. The signals coming
from the outputs of this subwoofer are not filtered, thereby allowing more subwoofers to be
connected in a chain.

To build the daisy-chain, the outputs from the first subwoofer are connected to the inputs of the second

17

subwoofer. The outputs of the second subwoofer are connected to the inputs of the third subwoofer and
so on. All “MODE” switches in the subwoofer daisy-chain are set to the “PASS THROUGH” position
except the last which is set to “NORMAL”. The last subwoofer will then apply the bass management
filtering for the loudspeakers connected to its outputs.

When two subwoofers are daisy-chained together in the same system, the in-room sound pressure
level increases by 6 dB, three subwoofers gives an increase of 9.5 dB and four subwoofers gives an
increase of 12 dB compared to a single subwoofer. To compensate for this increase in bass level, adjust
“SUBWOOFER LEVEL” in all the subwoofers in the daisy-chain down to the same level to match the
sound level to the loudspeaker sound level.

Controls selection

The subwoofer works in stand-alone mode when the GLM Control Network is not connected.
The “CONTROLS SELECTION” switch allows selection between two basic methods to control
a subwoofer in stand-alone mode.

“MANUAL CTRLS” refers to controlling the subwoofer using the controls on the subwoofer’s
connector panel.

“STORED CTRLS” refers to using the settings stored inside the memory of the subwoofer. These settings
can be set using the GLM Loudspeaker Manager Software and the GLM control network. The stored
settings provide additional functionality compared to the basic controls on the panel.

When the GLM Control Network is connected, or when the “CONTROLS SELECTION” switch is in the
“STORED CTRLS” position, some of the controls on the subwoofer’s electronics panel may be disabled
(see table below). They are disabled because the subwoofer is being controlled through the GLM Control
Network, or by the settings stored inside the memory of the subwoofer. If a disabled control on the panel
is adjusted, all the lights on the connector panel flash rapidly to inform that the control is disabled and that
the change has no effect.

Selection Switch setting

LFE In
Use

LFE
AES/EBU
Channel

LFE
Bandwidth

Redirect LFE

+10 dB

Bypass Mode Tone

Controls

Subwoofer
Level

System
Level

STORED Disabled Disabled Disabled Disabled Active Active Disabled Disabled Disabled Disabled

MANUAL
CTRL

Active Active Active Active Active Active Active Active Active Active

18

Roll-Off

The frequency response of the subwoofer may have to be adjusted to match the acoustic environment.
The Bass Roll-Off adjustment reduces the level of the very low subwoofer frequencies. You can combine
the -2 dB, -4 dB and -8 dB switches, providing an attenuation range from 0 to -14 dB – see table below
for examples of combinations and the corresponding attenuation.

Roll-Off Sw 1 (-8 dB) Sw 2 (-4 dB) Sw 3 (-2 dB)

-0 dB OFF OFF OFF

-2 dB OFF OFF ON

-4 dB OFF ON OFF

-6 dB OFF ON ON

-8 dB ON OFF OFF

-10 dB ON OFF ON

-12 dB ON ON OFF

-14 dB ON ON ON

Test Tone:

The DSP subwoofers contain a tone generator for phase alignment. The “TEST TONE” switch activates
the tone generator at the crossover frequency. The test tone signal is sent to OUTPUT 1 on AES/EBU
subframe A. To perform an adjustment one main loudspeaker has to be connected to this channel and set
to reproduce this signal with the subwoofer.

Phase:

The phase relationship between a main loudspeaker and the subwoofer must be adjusted at the crossover
point. A 0, -90, -180 or -270 degrees of adjustment is provided at 85 Hz – see table below for switches
combinations and the corresponding phase change. Incorrect phase alignment between the loudspeakers
and the subwoofer causes a drop in the frequency response around the crossover frequency.

Acoustic measuring equipment such as Genelec AutoCal accurately align the phase. Alternatively, the
following quick phase alignment process can be done:

Phase Sw 6 (-180 deg) Sw 7 (-90 deg)

0° OFF OFF

-90° OFF ON

-180° ON OFF

-270° ON ON

19

• Disconnect all loudspeakers from the subwoofer outputs.

• Select the loudspeaker to be used as the reference for the phase alignment. Typically, this is the
Front Center loudspeaker in a 5.1 multi-channel system.

• Connect this loudspeaker to subwoofer’s AES/EBU OUTPUT 1 connector.

• Select subframe A for reproduction on the reference loudspeaker.

• The test tone is played simultaneously from the subwoofer and loudspeaker.

• Listen to the tone and adjust both “PHASE” control switches to find the setting that gives the
minimum tone level at the listening position.

• After having found this minimum level setting, set the “-180 DEG” switch to the opposite setting to
complete the setup. This puts the subwoofer in phase with the reference loudspeaker and
completes the phase calibration.

• Finally, reconnect all loudspeakers to the subwoofer outputs.

In a system with multiple daisy-chained subwoofers, the Phase and Bass Roll-Off adjustments should be
performed individually for each subwoofer in the system.

• Set the “MODE” switch on all subwoofers to the ”NORMAL” position and disconnect the cables
from the outputs of all the subwoofers.

• Follow the phase alignment process detailed above by connecting the reference loudspeaker to
each subwoofer in turn and adjust the “PHASE” control switches.

•

Finally, set the “MODE” switches on all subwoofers to a setting appropriate for their position in the
daisy-chain - all subwoofers set to “PASS THROUGH” mode except the last which is set to
“NORMAL”.

Subwoofer level

The level of the subwoofer relative to the loudspeakers can be adjusted with the “SUBWOOFER LEVEL”
rotary control. This control allows matching the subwoofer level to the levels of the other loudspeakers.

When two subwoofers are daisy-chained together in the same system, the in-room sound pressure
level increases by 6 dB, three subwoofers gives an increase of 9.5 dB and four subwoofers gives an
increase of 12 dB compared to a single subwoofer. To compensate for this increase in bass level, adjust
“SUBWOOFER LEVEL” in all the subwoofers in the daisy-chain to the same level to match the sound
level to the loudspeaker sound level.

System level

All digital audio inputs and outputs are referenced to 0 dBFS (digital Full Scale, the largest possible signal
that can be represented by an AES/EBU signal). Genelec DSP loudspeakers produce a sound pressure
level of 100 dB (at one meter distance in free space) for a digital input signal of –30 dBFS.

20

If the digital source can control the digital level, it may be advantageous to lower the sensitivity either with
the GLM or the ”SYSTEM LEVEL” control of the DSP subwoofer. This will enable the use of the upper end
of the digital level controller.

The “SYSTEM LEVEL” switch group allows scaling the maximum sound level of the whole loudspeaker
system. This control changes the subwoofer level as well as the levels of all loudspeakers connected to
the subwoofer outputs.

It may be necessary to use the “SYSTEM LEVEL” attenuation switches to ensure that high-level digital
audio signals do not overload the loudspeaker system. The suitable setting also depends on the listening
distance. The correct setting for this control depends on the program source and the maximum sound
level needed.

Note that when daisy-chaining subwoofers, the “SYSTEM LEVEL” controls in all subwoofers in the daisy­chain must be set to the same setting. For example, if the “SYSTEM LEVEL” control is set to –10 dB, this
should be set on all subwoofers in the daisy-chain.

Connector panel warning light

Normally the light on the connector panel of an 7200 subwoofer is green, indicating that the subwoofer is
in normal operational mode.

If the output capacity of the power amplifier is exceeded (clipping in the power amplifier), the light turns
yellow. Red colour indicates thermal overload of the power amplifier or loudspeaker drivers (thermal
protection has activated). In each of these cases, turn the source level down.

Bit errors in the AES/EBU digital audio data or exceeding the maximum input range of the digital output
cause audible distortion, but are not indicated by the warning light.

Typical applications of different LFE bandwidth settings

Using the 85 Hz LFE bandwidth setting with "Redirect" function is the most universal configuration
for LFE monitoring. However, there are situations when the band-limited LFE settings serve a definite
purpose.

Limiting the LFE bandwidth to 85 Hz without using the "Redirect" function can be used to simulate the
effect of some consumer decoders that do not replay information above 80 Hz on the LFE channel when

21

the bass management is used. Checking the multichannel mix with this setting on lets you know how it
translates in systems with this limitation.

The 120 Hz LFE bandwidth setting complies with the replay systems of movie theaters and cinemas.
35 mm movie soundtracks use the LFE channel to reproduce a bandwidth of 20 - 120 Hz through
dedicated subwoofers. In this case the LFE and main channel bandwidths overlap between 85 and 120
Hz, which may create unwanted acoustical summing if the same signal is present in both channels. To
avoid this, the LFE content should be kept completely different (de-correlated) from the low frequency
content of the main channels when mixing music and sound effects for film release.

Maintenance

No user serviceable parts are to be found within the subwoofer enclosure. Any maintenance or repair of
the loudspeaker should be undertaken by qualified service personnel only.

Safety considerations

Although the 7260A, 7270A and 7271A have been designed in accordance with international safety
standards, to ensure safe operation and to maintain the subwoofer under safe operating conditions, the
following warnings and cautions must be observed:

1. Servicing and adjustment may only be performed by qualified service personnel.
The subwoofer enclosure must not be opened.

2. Do not use this product with an unearthed mains cable or a mains connection without the
protective earth contact as this may lead to personal injury

3.

To prevent fire or electric shock, do not expose the unit to water or moisture.
Do not place any objects filled with liquid, such as vases on the subwoofer or near it.

4. Note that the amplifier is not completely disconnected from the AC mains service unless
the mains power cord is removed from the subwoofer or the mains outlet.

5. Free flow of air around the subwoofer is necessary to maintain sufficient cooling.
Do not obstruct airflow around the subwoofer.

WARNING!

Genelec 7260A, 7270A and 7271A subwoofers are capable of producing sound pressure levels in excess
of 85 dB, which may cause permanent hearing damage.

Guarantee

Genelec 7260A, 7270A and 7271A subwoofers are supplied with one year guarantee against manufacturing
faults or defects that might alter the performance of the subwoofer. Refer to supplier for full sales and
guarantee terms.

22

7260A 7270A 7271A

Free field frequency response (± 3.0 dB)

19 Hz - 100 Hz

Maximum short term sine wave SPL output
averaged from 30 to 85 Hz, measured in half space
at 1 meter

≥฀108 dB SPL ≥฀112 dB SPL ≥฀118 dB SPL

Maximum peak SPL output with random pink noise,
measured in half space @ 1 meter

≥฀113 dB SPL ≥฀117 dB SPL ≥฀123 dB SPL

Self generated noise level in free field @ 1 m
(A-weighted)

≤฀15 dB

Harmonic distortion @ 1 m in half space

30 to 85 Hz
2nd
3rd

@ 90 dB SPL

≤฀3 %

≤฀2 %

@ 95 dB SPL

≤฀3 %

≤฀3 %

@ 100 dB SPL

≤฀3 %

≤฀3 %

Driver, magnetically shielded: 250 mm (10”) 305 mm (12”) 2 x 305 mm (12”)

Weight: 27 kg (58 lbs) 51 kg (111 lbs) 82 kg (179 lbs)

Dimensions:

Height
Width
Depth

527 mm (20 3/4”)
462 mm (18 3/16”)
363 mm (14 5/16”)

625 mm (24 5/8”)
555 mm (21 7/8”)
490 mm (19 5/16”)

755 mm (29 3/4”)
803 mm (31 5/8”)
490 mm (19 5/16”)

7260A 7270A 7271A

Short term amplifier output power (Long term output
power is limited by driver unit protection circuitry)

120 W 250 W

500 W

Amplifier system distortion at nominal output

THD

≤฀0.05 %

≤฀0.05 %

≤฀0.05 %

Mains voltage 100, 120, 220 or 230 V according to region

Voltage operating range ±10 %

±10 %

±10 %

Power consumption

Idle
Full output

15 VA
150 VA

15 VA
250 VA

30 VA
500 VA

7260A 7270A 7271A

Subsonic filter (18 dB/octave) below 19 Hz

Crossover frequency, (sub/main channels) 85 Hz default in stand-alone use

LFE cutoff Hz 85 Hz/120 Hz selectable

Bass Roll-Off control operating range in 2 dB steps
@ 20 Hz

From 0 to –14 dB

Phase matching control in 90° steps From 0 to -270°

Subwoofer Level control 0 to -18 dB

System Level control 0 to -35 dB in 5 dB steps

23

7260A 7270A 7271A

Digital audio input connectors 4 XLR female

Digital audio input impedance 110 Ohm

Digital audio output connectors 4 XLR male

Digital audio output impedance 110 Ohm

Digital audio format AES/EBU (AES3-2003)

Can also be used with S/P-DIF and AES3id signals when
impedance converters are used

Digital audio word length 16 bits, maximum 24 bits.

Fixed point, AES/EBU format

Digital audio sample rate 32 kHz, maximum 192 kHz

Supports single-wire and dual-wire AES signals.

The free f ield frequency response
of the 7260A subwoofer at different
Bass Roll- Off settings

The free f ield frequency response
of 7270A and 7271A subwoofers at
different Bass Roll-Off settings.

Genelec Document D0057R001c. Copyright Genelec Oy 4. 2007. All data subject to change.