GEMMY 39914 User Manual
INSTRUCTIONS
Congratulations! You are the proud owner of a Gemmy LED Light Rod
Christmas Tree. Please read over the directions carefully before using your
LED Light Rod Christmas Tree.
pg.1
CAUTION
WARNING
READ AND
FOLLOW
ALL SAFETY
INSTRUCTIONS
CAUTION: DO NOT place children, animals or other objects inside or
on your LED Light Rod Christmas Tree.
CAUTION: Do not attempt to assemble or operate your LED Light Rod
Christmas Tree during unusually strong winds. If it becomes
too windy for safe operation, please disassemble your LED
Light Rod Christmas Tree and bring indoors until conditions
improve.
CAUTION: Operation of your LED Light Rod Christmas Tree during ex-
treme weather conditions is not recommended.
SAFETY WARNING: Remove all plastic fasteners and tags. These are part of
the packaging and should be discarded.
This item is not a toy and should be used for decorative purposes only.
IMPORTANT SAFETY INSTRUCTIONS FOR
OUTDOOR TRANSFORMER
When using electrical products, basic precautions should always be practiced including the following:
1. Read and follow all instructions that are on the product or provided with
the product.
2. For a cord-connected or direct plug-in power unit, do not use an extension cord.
3. Reference the National Electrical Code, ANSI/NFPA 70, specifically for
the installation of wiring and clearances from power and lighting conductors.
4. Installation work and electrical wiring must be done by qualified person(s)
in accordance with all applicable codes and standards, including firerated construction.
5. For a cord-connected or direct plug-in power unit, do not install or use
within 10 feet of a pool.
6. For a cord-connected or direct plug-in unit, do not use in a bathroom.
7. WARNING: Risk of Electric Shock. When used outdoors, install only to a
covered Class A GFCI protected receptacle that is weatherproof with the
power unit connected to the receptacle. If one is not provided, contact a
qualified electrician for proper installation. Ensure that the power unit and
cord do not interfere with completely closing the receptacle cover.
8. WARNING: Risk of Fire. Installation involves special wiring methods to
run wiring through a building structure. Consult a qualified electrician.
9. Adults Note: Periodically examine this product for damage to the cord,
housing or other parts that may result in the risk of fire, electric shock or
injury. If the product is damaged, do not use it.
WARNING
1. This is not a toy, keep away from children.
2. If the supply cord or wires are damaged, it must be replaced by the manufacturer, its
service agent, or similarly qualified persons in order to avoid a hazard.
pg.2
SAVE THESE
INSTRUCTIONS
CONTENTS
ASSEMBLY
INSTRUCTIONS
This manual contains important, safety and operating instructions for power
units.
LED Light Rod Tree (collapsed) 1 piece
Stakes 5 pieces
UL Listed Outdoor Adapter 1 piece
Input: 120V ~ 60Hz
Output: 4.5V 3.33A
Assembly Time: Approximate 10 minutes.
1. Remove contents from packaging. Lay out in a clear and
flat area.
2. Attach each of the poles to the upper section poles by
aligning the pins, insert and turn clock-wise to tighten. The
legs will not make proper contact unless they are inserted
correctly. (see photo 1).
3. Once all poles are securely attached, gently hold Tree upright and off the ground. With one hand in-between all the
poles, simply expand your hand and the poles will extend
outward (see Photo#2) Set down.
photo 1
photo 2
DISASSEMBLY
TROUBLE
SHOOTING
CHECKLIST
FREQUENTLY
ASKED
QUESTIONS
(FAQS)
4. Secure each rod using the Stakes. (See photo #3)
5. Place the power cord into the cord holders, located on the
post. This will secure the cord in place prior to connecting
to the AC Adapter. (See photo #4)
6. Attach the adapter to the cord as shown. (See photo #5)
Then plug the UL Listed Adapter into a standard wall outlet
or a UL-approved outdoor extension cord.
1. Remove stakes from ground.
2. Lift up on tree rod and place back in its original box.
If your LED Light Rod Christmas Tree is not lighting up, the problem may be:
1. The power source is disabled.
2. The Power Cord may be unplugged.
3. The Poles are not assembled securely.
1. Can I leave my LED Light Rod Christmas Tree running overnight?
We recommend that you turn off while unattended. Under normal condi-
tions, extended use beyond 8 hours will not damage your LED Light Rod
Christmas Tree.
2. How can I clean my LED Light Rod Christmas Tree?
Wipe clean with a damp cloth and allow to dry before storing away.Use
mild detergent if necessary.
3. How much electricity does a LED Light Rod Christmas Tree consume?
Please reference the label attached to the Adapter.
4. What is the best way to store my LED Light Rod Christmas Tree?
Store dry in a bag, box or other storage container and keep in a cool, dry
location.
photo 3
photo 4
photo 5
Loading...