INSTRUCTIONS
Congratulations! You are now the proud owner of a LED LIGHT-
SHOW. Please read the directions carefully before use.
SAFETY WARNING:
are part of the packaging and should be discarded.
Remove all plastic fasteners and tags. These
SAVE THESE INSTRUCTIONS – This manual contains
important safety and operating instructions for power units.
WARNING
ELECTRIC PRODUCT. Keep away from children. As with all electrical products, precautions should be observed during handling and use to reduce the risk of electric
shock. If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualied persons in order to avoid a hazard.
WARNING
Strobe lights have been known to trigger seizures in people with photosensitive epilepsy.
WARNING
The light is very bright. Do not shine directly into eyes.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING(THIS FURNISHING)
WARNING: TO REDUCE THE RISK OF
BURNS, FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS ：
E-1
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
1. Do not secure the wiring of the product with staples or nails, or place on sharp
hooks or nails.
2. Do not let lamps rest on the supply cord or on any wire.
3. Do not close doors or windows on the product or extension cords as this may
damage the wire insulation.
4. Do not cover the product with cloth, paper or any material not part of the product
when in use.
5. Do not use seasonal products outdoors unless marked suitable for indoor and
outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided,
contact a qualied electrician for proper installation.
6. This seasonal use product is not intended for permanent installation or use.
7. Do not mount or place near gas or electric heaters, replace, candles or other
similar sources of heat.
8. Unplug the product when leaving the house, when retiring for the night, or if left
unattended.
9. This is an electric product-not a toy! To avoid risk of re, burns, personal injury
and electric shock it should not be played with or placed where small children can
reach it.
10. Do not use this product for other than its intended use.
11. Do not hang ornaments or other objects from cord, wire, or light string.
12. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet.
Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product.If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
13. This product has a polarized plug (one blade is wider than the other) as a feature
to reduce the risk of electric shock. This plug will t in a polarized outlet only one
way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t,
contact a qualied electrician. Do not use with an extension cord unless plug can
be fully inserted. Do not alter or replace.
14. Read and follow all instructions that are on the product or provided with the product.
CAUTION: To reduce the risk of re and electric shock:
1. Do not install on trees having needles, leaves or branch coverings of metal or ma-
terials which look like metal.
2. Do not mount or support wires in a manner that can cut or damage wire insulation.
E-2
ASSEMBLY INSTRUCTIONS
1. Gently remove contents from packaging
and lay out in a clear area.
2. Push the ball end of “A” through the Projection™ ring and base. Tighten the ring and
adjust the Projection™ to display in desired
location. (see Illustration 1)
3. Get together the Tripod Stake for outdoor
using, and separate the Tripod Stake for intdoor using. (see Illustration 2)
4. Plug power cord into standard wall socket. (see illustra-
tion 3)
4. Unplug when not in use.
A
B
Ground
illustration 1 illustration 2
illustration 3
USER SERVICING INSTRUCTIONS
Fuse Replacement (Fuse 2pcs)
WARNING
WARNING
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug
by pulling on the cord.
2. Open fuse cover. Slide open the fuse access cover on top of the attachment plug
towards blades. (See illustration)
3. Remove fuse carefully.
：
Risk of Fire: Replace only
with same size and type
of fuse.
：
Risk of Fire: Do not replace the attachment plug. Contains a safety device (fuse)
that should not be removed. Discard product if attachment
plug is damaged.
E-3
Working
Fuse
Replace
Fuse
4. Replace fuse only with 5 Amp Max, 125 Volt fuse (provided with product)
5. Close the fuse cover. Slide closed the fuse access cover on top of the attachment
plug.
OPERATING DETERMINATIONS
This product was designed for indoor and outdoor use.
Do not shake the device. Avoid brute force when operating the device.
Keep away from direct insulation (particularly in cars) and heaters.
Do not permit operation by unqualied persons. Damages are usually the result of
unprofessional operation.
Never use solvents or aggressive detergents in order to clean the device. Rather use
a soft and damp cloth.
Please use the original packaging if the device is to be transported.
Unauthorized modications on the device are unacceptable due to safety reasons.
If this device is operated in any way different from the ways described in this manual,
the product may suffer damages and the guarantee becomes void.
OPERATION
- Insert the plug into socket.
- Adjust staked projector to display in desired location.
- Unplug when not in use. Use caution with power cord.
WARNING
• The device is for indoor and outdoor use.
• Please keep away from heaters and other heating sources.
IMPORTANT
Damage caused by the disregard of this user manual are not under warranty. The
dealer will not accept liability for any resulting defects or problems. Keep away from
heaters and other heating sources. If the device has been exposed to drastic tem-
perature uctuation (e.g. after transportation), do not switch it on immediately. Leave
the device switched off until it has reached room temperature. Please note that dam-
age caused by manual modications on the device or unauthorized operation by unqualied persons are not under warranty. Keep young children away from the device.
USE AND CARE INSTRUCTIONS
1. When the product is placed on a live tree, the tree should be well maintained and
fresh. Do not place on live trees in which the needles are brown or break off easily.
Keep the tree holder lled with water.
E-4
2. If the product is placed on a tree, the tree should be well secured and stable.
3. Before using or reusing, inspect product carefully. Discard any products that have
cut, damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
4. When storing the product, carefully remove the product from wherever it is placed,
to avoid any undue strain or stress on the product conductors, connections, and
wires.
5. When not in use, store neatly in a cool, dry location protected from sunlight.
CAUTION
1. For temporary (90 days max.) installation and use only.
2. To reduce the likelihood of excessive heat and possible damage, use only decorative
lamp accessories packaged with this product or marked for use with this product.
3. To reduce the risk of re or electric shock, do not attempt to replace lamps or modify
wiring or product.
4. This is an eletric product-not a toy. To avoid risk of re, burns, personal injury and elec-
tric shock it should not be played or placed where small children can reach it.
5. Do not connect to another lighting string, decorative outt or seasonal product.
6. Always unplug this product before installing or replacing fuses.
CAUTION
responsible for compliance could void the user’s authority to operate the equipment.
:
Changes or modications not expressly approved by the party
WARNING
NOTE:
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
This equipment has been tested and found to comply with the limits for
E-5
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
NOTE:
caused by unauthorized modications to this equipment. Such modications could
void the user’s authority to operate this equipment.
The manufacturer is not responsible for any radio or TV interference
THESE INSTRUCTIONS ARE FOR ITEM
117027
QD ID: 71866
Visit
WWW.GEMMY.COM
©2019 GEMMY INDUSTRIES CORP.
117 WRANGLER DRIVE. SUITE 100
COPPELL, TX 75019 U.S.A.
1 (877) 250-9032
MADE IN CHINA/PRINTED IN CHINA
for more information.
E-6
Loading...