GEMMY 1002013 Users Manual

E

LED LIGHTSHOW

INSTRUCTIONS

Congratulations! You are now the proud owner of a LED LIGHTSHOW. Please read the

directions carefully before use.

SAFETY WARNING: Remove all plastic fasteners and tags. These are part of the packaging and should

be discarded.

SAVE THESE INSTRUCTIONS – This manual contains important safety and operating

instructions for power units.

WARNING

ELECTRIC PRODUCT. Keep away from children. Not recommended for children under 3 years of age. As with all electrical
products, precautions should be observed during handling and use to reduce the risk of electric shock. If the supply cord
is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a
hazard.

WARNING

Strobe lights have been known to trigger seizures in people with photosensitive epilepsy.

IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used
in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. lf one is not provided,
contact a qualified electrician for proper installation.

2. This seasonal use product is not intended for permanent installation or use.

3. Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat.

4.

Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.

5. Do not let lamps rest on the supply cord or on any wire.

6.

Unplug the product when leaving the house, when retiring for the night, or if left unattended.

7.

This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played
with or placed where small children can reach it.

8. Do not use this product for other than its intended use.

9. Do not hang ornaments or other objects from cord, wire, or light string.

10. Do not close doors or windows on the product or extension cords as this may damage the wire insulation.

11. Do not cover the product with cloth, paper or any material not part of the product when in use.

12. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse
blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the
product. Replace the fuse as per the user servicing instructions(follow product marking for proper fuse rating)and check the
product. lf the replacement fuse blows, a short-circuit may be present and the product should be discarded.

13. Read and follow all instructions that are on the product or provided with the product.

CAUTION: To reduce the risk of fire and electric shock:

1. Do not install on trees.

2. Do not mount on support strings in manner that can cut or damage wire insulation.

3. Do not remove light string off the product and hang on trees or other places for decoration.

SAVE THESE INSTRUCTIONS

1

USE AND CARE INSTRUCTIONS

1. Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation

or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.

2. When storing the product, carefully remove the product from wherever it is placed, to avoid any undue strain or stress on

the product conductors, connections, and wires.

3. When not in use, store neatly in a cool, dry location protected from sunlight.

USER SERVICING INSTRUCTIONS

To replace the fuse:

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.

2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.

3. Remove fuse carefully. Turn fuseholder over to remove fuse.

4. RISK OF FIRE. Replace fuse only with 3 Amp, 125Volt fuse (provided with product.)

5. Close fuse cover. Slide closed the fuse access cover on top of attachment plug.

6. RISK OF FIRE. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed.

Discard product if the attachment plug is damaged.

OPERATE THE REMOTE:

1. Remove the remote from its packing box.

2. Remove the battery compartment cover. (Fig.1) Install the included 23A battery.

Ensure the battery is installed correctly with regard to polarity (+ and -).

3. The remote has two buttons (Fig 2).

Fig. 1 Fig. 2

a. ON/OFF – Press to turn the set ON; press again to turn the set OFF.
b. FUNCTION: Light Colors: Change the light color to any on this list by pressing the button on remote until you reach the

desired color.

1.TOTAL LIGHTSHOW™

2.SPARKLE™

3.STARRY NIGHT™

4.STEADY GLOW™

5.SHOOTING STAR™

NOTES:

1. When using the remote to turn ON your set there may be up to a 2 seconds delay before the light pattern starts working.

2. To change light patterns it is recommended to wait 2 seconds each time after pressing the Function button until you reach

the desired pattern.

3. If for any reason the signal from the remote (transmitter) to the control box (receiver) hangs up, please turn off and then

restart the power to the set.

4. If a power interruption, the system’s memory keeps the last light pattern displayed.

5. The effective operating distance of the remote is 20’ (6m).

SETTING SAME LIGHT PATTERN ON MULTIPLE SETS

Before installing your sets you will need to preset each string to the same light pattern.

1. Plug one set into a working 120V outlet.

2. Using any remote press the Function button until you have selected the desired lighting effect and note that pattern from

the remote.

3. Unplug the set and then plug in the next set into the same outlet for ease of controlling.

4. With the remote follow Steps 2 and 3 setting the same light pattern (same function ) as the previous set.

2