GE MDS DS-ENETL2TU Users Manual

05-4186A01-eNETL2TUV_Manual_RevD.doc
GE MDS eNETL2T/U/V Manual
P/N 05-4186A01 Rev D.
05-4186A01 Rev. D Page 1 of 7 2/17/2015
05-4186A01-eNETL2TUV_Manual_RevD.doc
Table of Contents
1.1 RF Exposure ......................................................................................................................................................................... 3
1.2 FCC Approval Notice ....................................................................................................................................................... 3
1.3 FCC Part 80 Information ............................................................................................................................................... 3
1.4 FCC Part 90 Information ............................................................................................................................................... 3
1.5 FCC Part 95 Information ............................................................................................................................................... 3
2.1 Product Description ......................................................................................................................................................... 4
2.2 Power Control Loop Modes ......................................................................................................................................... 4
3.1 J101 Control Interface ................................................................................................................................................... 5
3.2 J102 RF Output .................................................................................................................................................................. 5
3.3 J103 RF Input ...................................................................................................................................................................... 5
3.4 J104 External/Internal Keying Jumper ................................................................................................................. 5
3.5 R112 Power Control Adjustment .............................................................................................................................. 5
4.1 Mounting the Unit ............................................................................................................................................................. 6
4.2 Connecting the Unit ........................................................................................................................................................ 6
05-4186A01 Rev. D Page 2 of 7 2/17/2015
05-4186A01-eNETL2TUV_Manual_RevD.doc
Amplifier Power Setting
ERP
Maximum Antenna Gain
2 W
4 W
3 dBd (5.2 dBi)
4 W
4 W
0 dBd (2.2 dBi)
2 W
20 W
10dBd (12.2 dBi)
10 W
20 W
3 dBd (5.2 dBi)
20 W
20 W
0 dBd (2.2 dBi)
1 Important Information
1.1 RF Exposure
Professional installation required. The radio equipment described in this guide emits radio frequency energy. Although the power level is low, the concentrated energy from a directional antenna may pose a health hazard. Do not allow people to come closer than 2.07 meters (6.79 feet) to the antenna when the transmitter is operating in indoor or outdoor environments. More information on RF exposure can be found on the Internet at: www.fcc.gov/oet/info/documents/bulletins.
1.2 FCC Approval Notice
This device is offered as a licensed transmitter per FCC Parts 80, 90 and 95. It is approved for use under the following conditions: Changes or modifications not expressly approved by GE MDS, LLC will void the user’s authority to operate the equipment.
1.3 FCC Part 80 Information
For FCC Part 80, valid frequencies are 216-218 MHz pursuant to Part 80.385 at up to 40 watts input to the antenna terminals (as per this product’s grant) pursuant to Part 80.215(h)(5).
1.4 FCC Part 90 Information
For FCC Part 90, valid frequencies are 217-220 MHz at up to 2 Watts input to the antenna terminal pursuant to Part 90.259 or 220-222 MHz at up to 500 Watts Effective Radiated Power (ERP) pursuant to Part 90.729 and applicable antenna height restrictions.
1.5 FCC Part 95 Information
For FCC Part 95, valid frequencies are 218-219 MHz. The Effective Radiated Power (ERP) must be less than or equal to 4 Watts for mobile use and 20 Watts for fixed use pursuant to Part 95.855. This can be accomplished by adjusting the output power of the amplifier and selecting an antenna with appropriate gain. Consult the following table for assistance in setting the output power and selecting an antenna to maintain compliance. The table provides examples, however other combinations can be used.
05-4186A01 Rev. D Page 3 of 7 2/17/2015
Loading...
+ 4 hidden pages