GE INTERLOGIX SIMON 3 User Manual

0 (0)

)

Part No: 60-875

60-910 (Not investigated for use by UL)

466-1873 Rev F

September 2002

*( ,QWHUORJL[

Doors &		Motion			System
Windows		Sensors			Status
							H O M E S E C U R I T Y
	Arm			Disarm
1 / 2	3 / 4		5 / 6		7 / 8	9 / 0
							C O D E
Chime
Doors Motion			Time	Sensor		On	Off
							H O M E C O N T R O L
Bypass					Lights
							E M E R G E N C Y
	FIRE		POLICE			AUX

Test Weekly

Simon® Security

System

Installation Instructions

FCC Notices

FCC Part 15 Information to the User

Changes or modifications not expressly approved by Interlogix Inc. can void the user’s authority to operate the equipment.

FCC Part 15 Class B

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits.

•Consult the dealer or an experienced radio/TV technician for help.

FCC ID: B4Z-787E-SIMON

ACTA Part 68

This equipment complies with Part 68 of the FCC Rules. Located on this equipment is a label that contains, among other information, the FCC registration number and the ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.

FCC Part 68 Registration No. B4ZUSA-27621-AL-E REN: 0.2B

The REN is used to determine the maximum number of devices that may be connected to your telephone line. Excessive RENs on a telephone line may result in devices not ringing in response to an incoming call. In most areas, the sum of all device RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements as adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compliant modular jack that is also compliant. See the Installation Instructions for details.

Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly installed RJ31X jack that is electrically in series and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the following diagram. If you have any questions concerning these instructions, consult your local telephone company or a qualified installer about installing an RJ31X jack and alarm dialing equipment for you.

	CustomerPremisesEquipmentandWiring
Network		AlarmDialing
Service	RJ31X
		Equipment
Provider's	Jack

Facilities

Unused	Computer
Unused
RJ-11Jack

Telephone
Line
		Answering	Telephone
		System	Telephone
		System
			Unused
			RJ-11Jack
Network	Telephone	FaxMachine
	Telephone

Demarcation
Point
		Telephone

If this equipment causes harm to the telephone network, the telephone company may temporarily disconnect your service. If possible, you will be notified in advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. You will be given advance notice in order to maintain uninterrupted service.

If you experience trouble with this equipment, please contact the company that installed the equipment for service and/or repair information. The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning.

This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.

)

*( ,QWHUORJL[

! "

Canada Notice

The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a singleline individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

For your protection, make sure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together

!Do not attempt to make connections yourself. Contact the appropriate electrician or electric inspections authroity.

Caution

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the devices does not exceed 100. Load Number: .1 The term “IC:” before the certification/registration number only signifies that the Industry Canada technical specifications were met. IC: 867A 787SIMON

“AVIS: - L ´étiquette du ministère des Communications du Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme a certaines normes de protection, d ´ exploitation et de sécurité des réseaux de télécommunications. Le ministère n ´ assure toutefois pas que le matériel fonctionnera a la satisfaction de l ´ utilisateur.

Avant d ´ installer ce matériel, l ´ utilisateur doit s ´ assurer qu´ il est permis de le raccorder aux installations de l ´ enterprise locale de télécommunication. Le matériel doit également etre installé en suivant une méthod acceptée de raccordement. Dans certains cas, les fils intérieurs de l´ enterprise utilisés pour un service individuel a ligne unique peuvent etre prolongés au moyen d´ un dispositif homologué de raccordement (cordon prolongateur téléphonique interne). L ´ abonné ne doit pas oublier qu ´ il est possible que la conformité aux conditions énoncées ci-dessus n ´ empechent pas le dégradation du service dans certaines situations. Actuellement, les enterprises de télécommunication ne permettent pas que l ´ on raccorde leur matériel a des jacks d ´ abonné, sauf dans les cas précis prévus pas les tarrifs particuliers de ces enterprises.

Les réparations de matériel homologué doivent etre effectuées pas un centre d ´ entretien canadien autorisé désigné par le fournisseur. La compagne de télécommunications peut demander a l ´ utilisateur de débrancher un appareil a la suite de réparations ou de modifications effectuées par l ´ utilisateur ou a cause de mauvais fonctionnement.

Pour sa propre protection, l ´ utilisateur doit s ´ assurer que tous les fils de mise a la terre de la source d ´ énergie électrique, des lignes téléphoniques et des canalisations d ´´ eau métalliques, s ´ il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.

Avertissment. - L ´ utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d ´ inspection des installations électriques, ou a electricien, selon le cas”.

Une note explicative sur les indices de charge (voir 1.6) et leur emploi, a l ´ intention des utilisateurs du matériel terminal, doit etre incluse dans l ´ information qui accompagne le materiel homologué. La note pourrait etre rédigée selon le modèle suivant:

“L ´ indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui peut etre raccordée a un circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé peut etre constituée de n ´ import somme des indices de charge de l ´ ensemble des dispositifs ne dépasse pas 100.”

L ´ Indice de charge de cet produit est ____________.

Contents
About This Manual	1
Special Installation Requirements .....................................................................................................	1
UL Listed Installations ..................................................................................................................	1
Central Station Reporting ..............................................................................................................	2
UL Canada Listed Installations .....................................................................................................	2
California State Fire Marshall Listed Installations ........................................................................	2
Planning the Installation	3
Standard Panel ...................................................................................................................................	3
Interrogator 200 Audio Verification Module ....................................................................................	3
Installing the System	3
System Components..........................................................................................................................	3
Control Panel .................................................................................................................................	4
System Devices ..............................................................................................................................	4
Planning Sensor Types & Locations	6
Device Locations ...............................................................................................................................	6
Control Panel ..................................................................................................................................	6
Remote Handheld Touchpad ..........................................................................................................	6
Keychain Touchpad .......................................................................................................................	6
X10 Modules .....................................................................................................................................	7
House Code and Unit Numbers .....................................................................................................	7
Installing the System	8
Materials Needed ...............................................................................................................................	8
Opening the Panel Cover and Chassis ...............................................................................................	8
Mounting the Panel ...........................................................................................................................	9
Connecting Hardwire Devices ........................................................................................................	10
AC Terminals ...............................................................................................................................	10
HWIN1, HWIN2, and DCOUT Terminals ..................................................................................	10
Wiring Interior Sirens ......................................................................................................................	10
LD105 Hardwire Interior Siren ...................................................................................................	11
Wiring Exterior Sirens .....................................................................................................................	11
Hardwire Exterior Siren with Supervision ..................................................................................	11
Hardwire Exterior Siren without Supervision .............................................................................	12
Wiring Hardwire Contacts ...............................................................................................................	12
Wiring a Phone Line to the Panel.....................................................................................................	12
Full Line Seizure ..........................................................................................................................	13
No Line Seizure ...........................................................................................................................	14
Wiring the Power Transformer ........................................................................................................	14
Powering Up the Panel ....................................................................................................................	14
Installing the Panel Backup Battery ............................................................................................	14
Applying AC Power ....................................................................................................................	15
Installing X10 Modules ...................................................................................................................	15
Lamp and Appliance Modules .....................................................................................................	15
Universal Module ........................................................................................................................	15
Sensor Installation ...........................................................................................................................	16
Programming	16
Entering Program Mode ..................................................................................................................	16
Exiting Program Mode ....................................................................................................................	16

Simon Security System	Contents

Reset Memory to the Factory Defaults ...........................................................................................	16
Set the Clock ...................................................................................................................................	16
Adding (Learning) Sensors .............................................................................................................	17
X10 Module Operation ...................................................................................................................	18
Numbered Options ..........................................................................................................................	19
Option 01: Panel Piezo Beeps .....................................................................................................	20
Option 02: Panel Voice ................................................................................................................	20
Option 03: Latchkey ....................................................................................................................	21
Option 04: Primary Phone Number .............................................................................................	21
Option 05: Secondary Phone Number .........................................................................................	21
Option 06: Downloader Phone Number ......................................................................................	21
Option 07: Account Number .......................................................................................................	22
Option 08: Phone Lock ................................................................................................................	22
Option 09: Downloader Code ......................................................................................................	22
Option 10: Entry Delay ...............................................................................................................	22
Option 11: Exit Delay ..................................................................................................................	22
Option 12: Phone Mod 1 .............................................................................................................	23
Option 13: Phone Mod 2 .............................................................................................................	23
Option 14: DTMF Dialing ...........................................................................................................	24
Option 15: No Activity Time-out ................................................................................................	24
Option 16: Auto Phone Test ........................................................................................................	24
Option 17: Dialer Delay ..............................................................................................................	25
Option 18: Alarm Cancel Report .................................................................................................	25
Option 19: RF Timeout ................................................................................................................	25
Option 20: Manual Phone Test ....................................................................................................	25
Option 21: Opening Reports ........................................................................................................	26
Option 22: Closing Reports .........................................................................................................	26
Option 23: Force Armed Report ..................................................................................................	26
Option 24: AC Power Failure Report ..........................................................................................	26
Option 25: CPU Low Battery Report ..........................................................................................	26
Option 26: Fail to Communicate .................................................................................................	27
Option 27: Ring/Hang/Ring ........................................................................................................	27
Option 28: No Delay from Keychain Touchpad ..........................................................................	27
Option 29: Panel Piezo Alarms ...................................................................................................	28
Option 30: Panel Panic Alarms ...................................................................................................	28
Option 31: Downloader Enable ...................................................................................................	28
Option 32: 300 Baud ...................................................................................................................	28
Option 33: Audio Verification .....................................................................................................	28
Option 34: Fail to Open Report ...................................................................................................	29
Option 35: Fail to Close Report ...................................................................................................	29
Option 36: Sensor Activated Light Lockout Start Time ..............................................................	29
Option 37: Sensor Activated Light Lockout Stop Time ..............................................................	29
Option 38: Auto Arm ...................................................................................................................	29
Option 39: Siren Timeout ............................................................................................................	30
Option 40: Trouble Beeps ............................................................................................................	30
Option 41: Chime Voice ..............................................................................................................	31
Option 42: Speaker Level ............................................................................................................	31
Option 43: Numeric Pager/Voice Event Notification Phone Number .........................................	31
Option 44: Numeric Pager/Voice Event Notification Phone Mod 3 ...........................................	31
Option 45: Sensor Alarm Restoral Report ...................................................................................	32
Option 46: Fire Shutdown - AVM ...............................................................................................	32

Contents	Simon Security System

Option 47: AVM Mode ................................................................................................................	32
Option 48: Panic Talk - AVM ......................................................................................................	32
Option 49: Arming LEDs Shutdown ...........................................................................................	33
Option 50: RF Jam Detect ...........................................................................................................	33
Option 51: 24 Hour Tamper ........................................................................................................	33
Option 52: Unvacated Premises ..................................................................................................	33
Option 53: Hardwire Siren Supervision ......................................................................................	33
Option 54: Access Code Length ..................................................................................................	34
Option 55: Status Beep Volume ...................................................................................................	34
Option 56: Call Waiting ...............................................................................................................	35
Option 57: Supervisory/Tamper Report ......................................................................................	35
Option 58: Remote Touchpad Arming ........................................................................................	35
Option 59: Exit Extension ...........................................................................................................	35
Option 60: Secure Arming ...........................................................................................................	36
Option 61: Demo Mode ...............................................................................................................	36
Option 62: Supervisory Protest ...................................................................................................	36
Option 63: 24 Hour Time ............................................................................................................	36
Option 64: No Arm on Panel Low Battery ..................................................................................	36
Option 65: No Usage Report .......................................................................................................	37
Option 66: External Siren Delay .................................................................................................	37
Option 67: Quick Exit .................................................................................................................	37
Option 68: Swinger Shutdown ....................................................................................................	37
Option 69: SIA Limits .................................................................................................................	37
Option 70: Not Available .............................................................................................................	38
Option 71: Programming Report .................................................................................................	38
Option 72: Supervisory Time ......................................................................................................	38
Option 73: Modem Sensitivity ....................................................................................................	38
Option 74: Silent Panel Police Panic ...........................................................................................	38
Option 75: VOX Mic Gain ..........................................................................................................	39
Option 76: VOX Gain Range ......................................................................................................	39
Option 77: Manual Mic Gain ......................................................................................................	39
Option 78: VOX Receiver Gain ..................................................................................................	39
Option 79: Panel Cover Tamper ..................................................................................................	40
Option 80: Alarm Report Verification.........................................................................................	40
Option 81: Heating Set Point .......................................................................................................	40
Option 82: Cooling Set Point ......................................................................................................	40
Programming System Access Codes ...............................................................................................	41
Testing the System	41
Control Panel ...................................................................................................................................	41
Sensor Testing ..................................................................................................................................	42
Improving Sensor/Panel Communication .......................................................................................	44
Antenna ........................................................................................................................................	44
If a Sensor Fails the Sensor Test ..................................................................................................	44
Phone Communication ....................................................................................................................	44
Off-Site Phone Operation ................................................................................................................	45
Central Station Communication ......................................................................................................	45
Pager Communication .....................................................................................................................	46
2-Way Voice Operation ...................................................................................................................	46
Voice Event Notification .................................................................................................................	47
RF Thermostat Operation.................................................................................................................	47
X10 Operation .................................................................................................................................	47

Contents	Simon Security System

Manual Lamp Module Control ....................................................................................................	48
X10 Siren and Lamp Module Functions .....................................................................................	48
Emergency Planning	48
Appendix A: Troubleshooting	49
System Status ...............................................................................................................................	49
Control Panel ...............................................................................................................................	50
Options (Programmable by the homeowner) ..............................................................................	50
Sensors .........................................................................................................................................	50
X10 Modules ...............................................................................................................................	51
Appendix B: System Configuration	52
Sensor Assignments/Locations .......................................................................................................	52
Alphabetical Listing of Sensor Names ............................................................................................	52
Sensor Group Characteristics ..........................................................................................................	53
Home Control Planning ..................................................................................................................	54
System Access Codes ......................................................................................................................	54
Option Settings ................................................................................................................................	55
Specifications	58
Quick Reference Table	Back Page

Contents	Simon Security System

About This

Manual

This manual provides information for planning, installing, programming, and testing this security system. When necessary, this manual refers you to other documentation included with compatible devices.

Planning sheets are included for you to record sensor locations and software programming settings.

Special Installation Requirements

This security system can be used as a fire warning system, an intrusion alarm system, an emergency notification system, or any combination of the three.

Some installations may require configurations dictated by city/state codes, insurance, or Underwriter’s Laboratories (UL). This section describes the various component and configuration listings.

UL Listed Installations

This section describes the requirements for UL Listed installations.

Basic System

•Control Panel: 60-875-95R (basic panel)

60-875-01-95R (with *2-way voice) 60-875-10-3 (with *transmitter)

60-875-11-3 (with *2-way voice and *transmitter)

•Backup Battery 6V 1.2 AH (34-025)

•Standard Class II 9 VAC, 700 mA Power Transformer (22-109) or Class II 9 VAC, 700 mA Line Carrier Power Transformer (22-129)

•Hardwire Interior Siren (13-374) or Hardwire Exterior Siren (13-046)

*Not investigated for use by UL.

Household Burglary Alarm System Unit (UL 1023)

Basic system, plus:

•Hardwire Magnetic Contact (13-068 or 13-071) or Wireless Learn Mode Door/ Window Sensor (60-670)

•Option 01: Panel Piezo Beeps set to on

•Option 10: Entry Delay set to 45 seconds or less

•Option 11: Exit Delay set to 60 seconds or less

•Option 19: RF Timeout set to 24 hours

•Option 29: Control Panel Alarms turned on

•Option 38: Auto Arm set to on

•Option 39: Siren Timeout set to 4 minutes or more

•Option 40: Trouble Beeps set to on

•Option 50: RF Jam Detect set to on

•Option 53: Hardwire Siren Supervision set to on if Option 29: Control Panel Alarms is set to off

•Option 59: Exit Extension set to off

•Option 67: Quick Exit set to off

Household Fire Warning System (UL 985)

Basic system, plus:

•Wireless Smoke Sensor 60-848-95 learned into sensor group 26

•Option 01: Panel Piezo Beeps turned on

1	Simon Security System

Note

These option settings are in addition to UL 1023 and 985 and are required only if the system is set up for Central station reporting.

Note

Before beginning installation, installers must verify compatibility with the following central station receivers.

•Option 19: RF Timeout set to 4 hours

•Option 29: Control Panel Alarms set to on

•Option 39: Siren Timeout set to 4 minutes or more

•Option 40: Trouble Beeps set to on

•Option 50: RF Jam Detect set to on

•Option 53: Hardwire Siren Supervision set to on if Option 29: Control Panel Alarms is set to off

UL 1023 & 985 24-Hour Backup

•For 24-hour backup, the total current draw for all connected devices is limited to 25 mA (during normal standby conditions) using a 1.2 AH battery.

UL 1635 Digital Alarm Communicator System

Same as UL 1023 & 985, plus:

•Option 12: Phone Mod 1 set to 0 or 1

•Option 16: Auto Phone Test set to 001

•Option 19: RF Timeout set to 4 hours

•Option 24: AC Power Failure Report set to on

•Option 25: CPU Low Battery Report set to on

•Option 26: Fail to Communicate set to on

•Option 50: RF Jam Detect set to on

Central Station Reporting

The panel has been tested with the following central station receivers using SIA and Contact ID reporting formats:

•Radionics D6600 Central Station Receiver

•Sur-Gard Central Station Receiver with models SG-DRL2A and SG-CPM2

•CS5000 Digital Alarm Communicator Receiver

UL Canada Listed Installations

This section describes the requirements for CUL (UL Canada) Listed installations.

Canadian Standards CSA Certified Accessories

Residential Burglary Alarm System Unit (ORD-C1023-1974)

Basic system as described for “UL 1023 Listed Installations” plus:

•Hardwire Magnetic Contact (13-068 or 13-071) or Wireless Learn Mode Door/ Window Sensor (60-670)

•Option 39: Siren Timeout set to 5 minutes or more

Residential Fire Warning System Control Unit (ULC-S545-M89)

Basic system as described for “UL 985 Listed Installations” plus:

•Wireless Smoke Sensor 60-848-95 learned into sensor group 26

•Option 39: Siren Timeout set to 5 minutes or more

•For 24-hour backup, the total current draw for all connected devices is limited to 33 mA (during normal standby conditions) using a 1.2 AH battery.

California State Fire Marshall Listed Installations

Applied for.

Simon Security System

Planning the

Installation

This section describes system capabilities to help you get familiar with the system. “Appendix B” provides planning sheets with tables that let you record the hardware and programming configuration of the system. Fill in all necessary information ahead of time to help prepare for system installation.

Standard Panel

The following describe the basic panel (out-of-box) hardware capabilities.

•Power: Input for an AC step-down, plug-in style transformer.

•2 Siren Outputs/Zone Inputs: Terminals for connecting hardwire sirens or normally closed (NC) loop switch circuits.

•Phone Line Connection: Allows panel to communicate with central monitoring station and/or pagers.

Interrogator 200 Audio Verification Module

Adding this module allows central station operators to listen-in and talk to occupants on the premises to verify an emergency when an alarm report is received.

Installing the	This section describes how to install the system control panel. Before starting installa-
System	tion, plan your system layout and programming using the worksheets in “Appendix B.”
	Installing the system consists of the following:
	• Determining Panel and Device Locations
	•	Mounting the Panel
	•	Connecting Sirens

• Connecting Normally Closed Loop Switch Circuits

• Connecting the Phone Line to the Panel

• Connecting the AC Power Transformer

• Powering Up the Panel

System Components

The security system has three types of components: the control panel, devices that report to the panel, and devices that respond to commands from the panel (see Figure 1)

DOOR/WINDOW

SENSOR

MOTION

KEYCHAIN

SENSOR

*TOUCHPAD

SMOKE

STATUS

SENSOR

SYSTEM

ARM

Doors&

Windows

ARM

Motion

Sensors

DISARM

Doors& Motion

System

WindowsSensors

Status

HOME SECURITY

Arm

Disarm

1/2 3/4 5/6 7/8 9/0

CODE

Special

Doors Motion

Time

Sensor On Of

HOME CONTROL

Chime

Lights

EMERGENCY

EMERGENCY-

FIRE

POLICE AUX

* Not investigated for use by UL

REMOTEHANDHELD

TestWeekly

TOUCHPAD

*2-WayRF

TOUCHPAD

Hold Prog Mode Fan

HAI

< >

X-10POWERHOUSE

9 7

*RFELECTRONIC

THERMOSTAT

*UNIVERSAL

*LAMP *APPLIANCEMODULE

MODULE

Figure 1. Typical Security System Components

3	Simon Security System

Note

ToolBox has not been investigated by UL and should not be used to program panels in UL listed systems.

Control Panel

The control panel is the main processing unit for all system functions. It receives and responds to signals from wireless sensors and wireless touchpads throughout the premises. For monitored systems, the panel can be connected to the premises phone line for central monitoring station and/or pager reporting.

Two panel models are available. One has an on-board 2-way voice microphone, the

other does not. The Interrogator® 200 Audio Verification Module can be added to either panel.

User Interface

When the panel cover is closed, the panel buttons operate the security system. The user operates the panel by pressing panel buttons or by using a touchpad. See the User Manual for complete operation instructions.

When the panel cover is open, the buttons program the security system. The panel can

be programmed on-site by the installer or user, or from off-site using ToolBox® software. See the “Programming” section of this manual for complete on-site programming instructions. See the ToolBox manual and ToolBox on-line help for off-site programming instructions.

Panel Tamper

If the panel cover is opened while the system is armed, an intrusion alarm occurs. When the system status button is subsequently pressed, the panel says System Access Alarm.

System Devices

The system can monitor up to 24 sensors and may use any of the following:

Door/Window Sensor (60-670)

For intrusion protection, install Door/Window sensors on all ground-floor doors and windows. At a minimum, install them in the following locations:

•All easily accessible exterior doors and windows.

•Interior doors leading into the garage.

•Doors to areas containing valuables such as cabinets and closets.

Indoor Motion Sensor (60-639)

Indoor motion sensors are ideal whenever it is not practical to install door/window sensors on every opening. Identify areas where an intruder is likely to walk through. Large areas in an open floor plan, downstairs family rooms, and hallways are typical locations for indoor motion sensors. For installations with pets, use the SAW Pet Immune PIR (60-807).

Outdoor Motion Sensor (60-639)

Use outdoor motion sensors to detect motion in a protected outdoor area. Detected motion in this protected area can sound chimes or turn on outside lights. Do not use

Outdoor Motion Sensors for intrusion protection.

Freeze Sensor* (60-742)

Freeze sensors detect low temperature conditions which may indicate a furnace failure. The sensor contains a bimetallic thermal switch connected to the built-in transmitter. The sensor transmits an alarm signal to the panel when the surrounding temperature drops to about 41°F. When the temperature rises to 50°F, the sensor transmits a restore signal.

Water Sensor* (60-744)

Water sensors detect a water leak/rising water. The detector is connected to the sensor by an 8-foot (2.4-meter) cable. Water that reaches both detector contact points activates the sensor, causing it to transmit an alarm signal.

Simon Security System

Note

The ELM Keychain Touchpad is only compatible with Simon 3 panels version 3.3 and later.

Note

Use of X10 modules has not been investigated by UL.

Smoke Sensor (60-848-95)

Smoke sensors provide fire protection by causing an alarm to sound throughout the house. You can add smoke sensors near sleeping areas and on every floor of the house. Avoid areas that could have some smoke or exhaust such as attics, kitchens, above fireplaces, dusty locations, garages, and areas with temperature extremes. In these areas you may want to install Rate-of-Rise sensors to detect extreme temperature changes. See “Emergency Planning” and the instructions packaged with the smoke sensor for complete placement information.

Carbon Monoxide (CO) Alarm* (60-652-95)

The Learn Mode™ CO Alarm alerts users to hazardous levels of carbon monoxide gas. If dangerous concentrations of gas are present, the red indicator light comes on, the internal siren goes off, and an alarm is transmitted to the panel. The panel sounds its own alarm and reports to the central station.

Keychain Touchpad* (60-659)

The Keychain Touchpad lets you turn the system on and off from right outside the home or activate a panic alarm if there is an emergency. If you have X10 Lamp Modules, you can use keychain touchpads to turn all system controlled lights on and off.

ELM (Encrypted Learn Mode) Keychain Touchpad (60-832)

The ELM (Encrypted Learn Mode™) 2-Button Keychain Touchpad is an alkaline bat- tery-powered, wireless touchpad that allows users to arm and disarm their system, and activate a police or auxiliary panic alarm. Random encrypted signal transmissions provide high security to help prevent signal copying.

Remote Handheld Touchpad (60-671)

The Remote Handheld Touchpad lets you turn the system on and off while in the home, turn system controlled lights on and off (all or individual lights), or activate a panic alarm if there is a non-medical emergency.

Dialog Touchtalk 2-Way RF Touchpad* (60-924-3)

The wall-mounted wireless Dialog Touchtalk 2-Way RF Touchpad combines a conventional Learn Mode™ touchpad with an RF receiver, speech chip, and voice amplification circuit.

Dialog RF Electronic Thermostat* (60-909-95)

The Dialog RF Electronic Thermostat provides a money saving and convenient way to monitor and control temperatures. The thermostat uses low and high temperature limits to save energy. Temperature limits set on the thermostat determine when the heat or air conditioning turns on. There can be only one RF Thermostat per system.

X10 Modules*

When the panel is powered using the line carrier power transformer, the system can work with any of the following modules:

•X10 Lamp Module

•X10 Appliance Module (13-402)

•X10 Powerhorn/Remote Siren Module (13-398)

•X10 Universal Module (13-399)

Interrogator 200 Audio Verification Module* (60-787)

The Audio Verification Module (AVM) gives the central station operator the ability to hear what’s happening at the premises during an alarm and to speak directly to the system user. The operator can then determine how serious an alarm is, find out what kind of help is needed, and dispatch the appropriate assistance. Only one AVM may be installed per panel.

5	Simon Security System

Planning

Sensor Types &

Locations

The first step to an easy and successful installation is to decide what areas or items to protect, which lights or appliances to operate, and the best location for the panel, touchpad, sensors, and sirens.

Metal objects, mirrors, and metallic wallpaper can block signals sent by the wireless sensors. Make sure there are no metal objects in the way when installing the system.

Use the planning tables in “Appendix B” to determine the appropriate Sensor Type for the sensors you will be adding. You’ll need to understand the application for each sensor. For example, Keychain Touchpads are typically programmed as sensor group 01 (Portable panic), used to send an intrusion alarm to a central monitoring station. This sensor type is instant intrusion, it does not require restoral or supervisory communication with the panel and it is active in 4 arming levels (disarm, arm doors & windows, arm motion sensors, and arm doors/windows and motions sensors).

* Not investigated for use by UL.

Recommended Sensor Groups

Device	Recommended Sensor Group

Keychain Touchpad	01, 03, 06, 07

ELM Keychain Touchpad	01, 03, 06, 07

Remote Handheld Touchpad	01, 03, 06, 07

2-Way RF Touchpad	01, 03, 06, 07

Indoor Motion Sensor	17 (intrusion), 25 (chime)

Outdoor Motion Sensor	25

Smoke Sensor	26

Exterior Door	10

Interior Door	14

Window Sensor	13

CO Alarm	34

Freeze Sensor	29

Water Sensor	38

RF Electronic Thermostat	28

Device Locations

Control Panel

Locate the panel where alarm sounds can be heard and is easily accessible for operation.

Do not install the panel near a window or door where it can be reached easily by an intruder.

Remote Handheld Touchpad

Locate Remote Handheld Touchpads where they will be convenient and offer quick access to the user.

2-Way RF Touchpad

Locate 2-Way RF Handheld Touchpads where they will be convenient and offer quick access to the user. They must be mounted within 600 feet of the control panel.

Keychain Touchpad

Keychain Touchpads attach to the owner’s key ring or can be conveniently carried.

Simon Security System

Note

All Lamp Modules with the same house code will turn on or flash as a group during an alarm or when operating the “Light” button on a Keychain Touchpad.

Note

The house code instructions that come with the Powerhorn Siren won’t work with this panel. Follow the housecode instructions given here.

Note

If you are using a Universal Module to operate a device, make sure to assign a unique unit number to this module, choosing from 1-8.

X10 Modules

The system can control up to 8 individual unit numbers on Lamp, Wall switch, Appliance, and Universal Modules.

House Code and Unit Numbers

Each device (lamp, appliance, etc.) controlled by the panel must have an identification setting. The modules use two dials to set identification codes: one with letters A through P and one with numbers 1 through 16.

The lettered dial sets the house code, which enables the system to differentiate this home from other homes in the area. Set all modules (except the remote siren) and the panel to the same house code.

The numbered dial sets the unit number, which identifies and lets you control a specific device. Each device must have a unique unit number (1-8) to be individually controlled. For example, lights and appliances operated from a Remote Handheld Touchpad or operated by a sensor; or lights programmed to go on during the entry/exit delay or at scheduled times.

Note

When unit numbers 9-16 are used for lamp modules, they can only be controlled by an all on or all off command. A lamp will flash to the arming level if its unit number is set to 10. A lamp set to unit number 10 will flash once if the panel is disarmed, twice if doors & windows are armed, etc. The remote siren can be set to any unit number to hear alarm sounds. Set it to unit number 9 to also hear arming level beeps, status beeps, and trouble beeps. Do not use a lamp module to control appliances. Use an appliance module, since the wattage rating on Lamp Modules is less than on Appliance Modules.

To Fill Out the Home Control Planning Table:

1.Set the house code on all modules (except the remote siren) to the same letter.

2.Set the Remote Siren house code to the next alphabetical letter. For example, if you chose house code B in step 1 above, set the remote siren house code to C.

3.Set the module unit numbers.

4.List the location of the lamp or appliance in the Location column of the Home Control Planning Table.

5.Write the location of each Lamp Module on an adhesive note and label the module.

6.Decide if the device should be activated by sensors, entry/exit delay, time, or a combination. An example of sensor activation is using a motion sensor to turn on a light. Record the information in the appropriate columns.

Use the following tables to help you further plan X10 module installation.

X10 House Code Assignments

X10 Device	Settings

Lamp, Appliance, Universal	Set all modules to the same house code (A
	- P) except the remote sirens.

Remote Siren	House code must be set to the next higher
	alphabetical letter.

7	Simon Security System

			X10 Unit Number Assignements

		Unit #	Result

		1 - 8	Used for sensor-activated, time-activated, and entry/exit delay
			lights.
			Sensor-activated lights are enabled and disabled by pressing the
			LIGHTS Sensor Activated button on the panel.
			Time-activated lights are enabled and disabled by pressing the
			LIGHTS Time Activated button on the panel.
			If using the universal module to operate a device, be sure to assign
			a unique unit number.
			The STAR button on the KeyChain Touchpad activates the universal
			module controlled device or to turn on special lights if programmed.

		9	Used for remote siren or light control.
			For remote siren use, sirens with this setting sound alarms, arming
			level beeps, status beeps, and trouble beeps.
			For light control, lamp modules with this setting are controlled by an
			all on or all off command.

		10	Used for remote siren or light control.
			For remote siren use, sirens with this setting only sound alarms.
			For light control, lamps will flash according to selected arming level
			and are controlled by an all on or all off command.

		11 - 16	Used for lamp modules and controlled by an all on or all off com-
			mand.


Installing the	This section describes how to open the panel for mounting, mount the panel, connect
System	sirens, hardwire contacts, and the AC power transformer.

Materials Needed

•Pencil

•Phillips Screwdriver

Opening the Panel Cover and Chassis

Tabs at the top of the panel secure and release the front cover and the chassis. The plastic hinges on the panel bottom allow the cover and chassis to swing down and out of the way (see Figure 2).

Simon Security System

Press tab with thumb,				Press tab up with
Press tab with thumb,				screwdriver, then
then swing cover down.				screwdriver, then
then swing cover down.				swing chassis
				swing chassis
				down.
Doors& Motion
WindowsSensors			Status
			HOME SECURITY
Arm		Disarm	System
1/2 3/4 5/6 7/8 9/0
			CODE
Special
Doors Motion	Time	Sensor On Of
			HOME CONTROL
Chime		Lights
			EMERGENCY
FIRE	POLICE		AUX
	TestWeekly

Note

When choosing the AC outlet location for the AC power transformer, make sure the outlet is not controlled by a switch or that it is not part of a ground fault interrupt circuit (GFIC).

Figure 2. Opening the Panel Cover and Chassis

Mounting the Panel

The panel can be mounted on a wall or on the optional Tabletop Base.

1.Choose a panel location.

2.Run all necessary power, phone, siren, and hardwire contact wires to the desired panel location.

3.Refer to Figure 3 for mounting hole locations.

For wall mounting, hold the panel against the wall and mark the mounting hole locations with a pencil. For Tabletop Base mounting, place the panel back on the base until the top and bottom mounting holes line up with the mounting posts on the base.

9	Simon Security System

Mounting

Holes

Note

All inputs and outputs are Class II power limited circuits.

Note

These terminals cannot provide both functions simultaneously.

Note

The total current available from the DCOUT terminal is 250 mA at up to 122° F (50° C).

Figure 3. Panel Mounting Hole Locations

4.For wall mounting, insert anchors into holes where studs are not present.

5.Install all screws and tighten gently.

Connecting Hardwire Devices

The panel has 5 screw terminals located on the upper-right corner of the circuit board (see Figure 3) for connecting AC power, sirens and/or hardwire detectors.

AC Terminals

These terminals are used for connecting a 9 VAC, 700 mA AC power transformer. For systems with no X10 modules, use transformer part no. 22-109. For systems with X10 modules, use transformer part no. 22-TBD.

HWIN1, HWIN2, and DCOUT Terminals

These terminals are dual purpose and can be used for either siren or hardwire detector connections.

Sirens

From the factory, these terminals are set up for siren operation with HWIN1 handling interior sirens (status and alarm sounds), HWIN2 handling exterior sirens (alarm sounds only), and DCOUT providing the positive (+) voltage.

With Option 53: Hardwire Siren Supervision turned on, sirens connected to HWIN1 and HWIN2 are supervised and require a 4.7k resistor in the circuit. If either of these terminals is not used with Option 53 on, you must connect a 47k resistor between the unused terminal and DCOUT.

Hardwire Detectors

To set up HWIN1 and/or HWIN2 for hardwire detectors, make the required connections as described under “Wiring Hardwire Detectors,” then proceed to the “Programming” section to add (learn) them into panel memory.

Wiring Interior Sirens

Panel terminal HWIN1 can be used for connecting interior sirens and activates for status and alarm sounds.

Simon Security System

Note

Do not install the resistor at the panel terminals. This does not provide supervision of the wire.

Note

If you are installing only an interior siren and no exterior siren and Option 53 is on, you must connect a 4.7k resistor between the HWIN1 and DCOUT terminals.

Note

Do not install the resistor at the panel terminals. This does not provide supervision of the wire.

Note

If you are installing only an exterior siren and no interior siren and Option 53 is on, you must connect a 4.7k resistor between the HWIN2 and DCOUT terminals.

Interior sirens must always be wired with a resistor in the circuit. For circuit supervision which allows the panel to detect if the siren wire is cut (open), Option 53: Hardwire Siren Supervision must be turned on (see the “Programming” section).

LD105 Hardwire Interior Siren

Connect the LD105 Hardwire Interior Siren (13-374) to the panel using a 4.7k resistor (included with siren) as shown in Figure 4. The resistor must be connected across the siren wires as close to the siren as possible.

AC AC HWIN2DCOUTHWIN1

Red

Black

4.7k Resistor (located at siren)

Figure 4. Hardwire Interior Siren with Supervision

Wiring Exterior Sirens

Panel terminal HWIN2 can be used for connecting exterior sirens and activates when intrusion and fire alarms occur.

Exterior sirens can be wired with or without a resistor in the circuit for supervision. For circuit supervision which allows the panel to detect if the siren wire is cut (open), Option 53: Hardwire Siren Supervision must be turned on (see the “Programming” section).

Hardwire Exterior Siren with Supervision

Connect the Hardwire Exterior Siren (13-046) to the panel using a 4.7k resistor (included with siren) as shown in Figure 5. The resistor must be connected across the siren wires as close to the siren as possible.

AC AC HWIN2DCOUTHWIN1

Black

Red

4.7k Resistor

(located at siren)

Figure 5. Hardwire Exterior Siren with Supervision

11	Simon Security System

Hardwire Exterior Siren without Supervision

With Option 53 turned off, connect the Hardwire Exterior Siren (13-046) to the panel without a resistor as shown in Figure 6

AC AC HWIN2DCOUTHWIN1

Black

Red

Important !

Connect only normally closed (N/C) reed switches to HWIN1 and/or HWIN2. Other types of hardwire detectors should not be used.

Note

Do not install the resistor at the panel terminals. This does not provide supervision of the wire.

Figure 6. Hardwire Exterior Siren without Supervision

Wiring Hardwire Contacts

You can connect hardwire reed switches (normally closed loop only) to HWIN1 and/or HWIN2, if either terminal is not being utilized for a hardwire siren.

The total resistance of the wire loop must not exceed 3 ohms. This allows you to use up to 200 feet of 2-conductor, 22-gauge stranded wire.

Connect hardwire reed switches to the panel using a 47k resistor as shown in Figure 7. The resistor must be connected at the last switch in the circuit.

AC AC HWIN2DCOUTHWIN1

47k Resistor

Figure 7. Connecting Normally Closed Hardwire Reed Switches

Wiring a Phone Line to the Panel

You can connect a phone line to the panel for systems monitored by a central monitoring station and/or systems that notify users by a digital pager or voice event notification.

Basically, there are two methods for connecting the panel to a phone line; full line seizure and no line seizure.

Simon Security System

Note

For UL Listed systems, the RJ-31X jack must be mounted within 5 feet of the panel.

Note

If the customer ever adds a phone or other phone device to another phone jack, full line seizure no longer exists. Inform the customer to contact you if they want to add a phone or other device so that you can rewire for full line seizure by adding an RJ-31X.

Full Line Seizure

This method requires that the panel be wired ahead (or in front) of all other phones, answering machines, computers, or any other devices on the phone line. This allows the panel to take over (seize) the phone line, even if another device on the line is in use.

An RJ-31X (CA-38A) jack should be installed when wiring for full line seizure. This lets the user quickly and easily disconnect the panel from the phone line in case the panel disables the phone line due to a malfunction.

Full Line Seizure Wiring with an RJ-31X

1.Run a 4-conductor cable from the TELCO block to the RJ-31X (A in Figure 8).

2.Connect the 4-conductor cable wires to the RJ-31X (B in Figure 8).

3.Disconnect the Green and Red premises phone jack wires from the TELCO block and splice them to the 4-conductor cable Black and White (or Yellow) wires (C in Figure 8). Use weatherproof wire connectors for these splices.

4.Connect the 4-conductor cable Green and Red wires to the TELCO block TIP (+) and Red to RING (-) posts (D in Figure 8).

	BRN		GRY
				B
GRN			RED
Black	Green	Red	White	(or Yellow)

HWIN2

HWIN1

TIP RING		A
D (+)	(-)
Green	Red
Black	White (or Yellow)
C	White (or Yellow)
C

								Premises
	Green							Premises
	Green							Phone Jack
								Phone Jack
								Wires
								Wires

Lone Premises Phone

Premises

Phone Jack

HWN2I

HWN1I

Figure 8. Full Line Seizure Wiring with an RJ-31X Figure 9. Full Line Seizure Wiring with 1 Premises Phone

Full Line Seizure Wiring with 1 Premises Phone

If a single phone is all that exists on the premises, full line seizure can be accomplished without an RJ-31X.

1.Disconnect the phone from the premises phone jack and plug it into the panel PHONE jack (A in Figure 9). This jack is disconnected automatically whenever the panel reports.

2.Connect the phone cord included with the panel to the panel LINE IN jack and the premises phone jack (B in Figure 9).

13	Simon Security System

Note

Connecting the panel to a standard phone (voice) line in this manner should be avoided. Other devices in use at the same time the panel is using the line can prevent reports from going through.

Note

Do not plug in the transformer at this time

No Line Seizure

This method is typically used where DSL (digital subscriber line) service exists. DSL allows multiple devices on a single phone line to be used simultaneously. Simply connecting the panel LINE IN jack to an available phone jack on the premises is all that is required.

An in-line filter may be required to ensure panel reporting is successful.

* For UL installations, installer needs to verify line seizure.

Wiring the Power Transformer

Connect the power transformer to the panel AC terminals as shown in Figure 10.

AC AC HWIN2DCOUTHWIN1

Figure 10. Connecting the Power Transformer

Powering Up the Panel

When applying power to the panel connect the battery first, then plug in the AC power transformer. This sequence prevents a battery fault condition.

Installing the Panel Backup Battery

1.Position and push the battery between the 2 flexible tabs (A in Figure 11).

2.Slide the battery to the left until the tabs snap into place, securing the battery (B in Figure 11)

Tabs

+ +

Figure 11. Installing the Panel Backup Battery

3.Connect the red and black battery leads (included with panel) to the battery and panel terminals (see Figure 12 A - Open Battery / B - Covered Battery).

Connecting the Battery Leads to the Battery and Panel Terminals (see Figure 12).

Simon Security System

+ 47 hidden pages