Page 1
KKaallaatteell DDVVSSee
Installation and Users Manual
Page 2
Kalatel DVSe
2
0150
-
0178
F
Warning!
To prevent fire and electronic shock, do not expose this product to rain or moisture.
The lightning flash with the arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence of
uninsulated “dangerous voltage” within the
products enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point, within an equilateral
triangle, is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
!
Caution!
To prevent electric shock, do not remove cover. No user
serviceable components inside. Refer servicing to qualified
service personnel.
!
Caution! Lithium Battery
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the
manufacturer.
Attention
This product contains a recyclable lithium battery.
It may be illegal to dispose of this battery
improperly under local, state, or federal laws.
Check with your local waste management officials
for disposal and recycling options.
Caution! Electrostatic-Sensitive Device!
Use proper CMOS and MOSFET handing precautions, including approved
grounded wrists straps, etc., to avoid damage to this unit or its internal
components, from electric discharge.
Warning!
This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions in this manual, may cause
interference to radio communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to subpart J of part 15 of FCC rules which
are designed to provide reasonable protection against such interference when operated in
a commercial environment. This equipment has also been tested and found to comply with
the requirements for a CE Class A device and TUV safety standards.
Operation of this equipment in a residential area may cause interference, in which case the
user is required to take all measures that are necessary, at the user's expense, to correct
the interference.
Copyright Information
Software and/or firmware is furnished to the purchaser under a license for use on a single
system. Software and/or firmware included with this equipment are the sole proprietary
property of, confidential to, and copyrighted by GE Interlogix, Corvallis, Oregon, USA. The
software/firmware are not to be copied or disclosed in any manner without the express
written consent of GE Interlogix.
All information and specifications furnished by GE Interlogix are believed to be accurate
and reliable. No responsibility is assumed by GE Interlogix for neither its use nor any
infringements of rights of third parties that may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of GE Interlogix.
The Kalatel™ brand name and product model numbers are the property of GE Interlogix.
COPYRIGHT, 2003: The contents of this manual may not be copied or reproduced in any
manner or form without the prior written consent of GE Interlogix.
Page 3
0150
-
0178
F 3 Kalatel DVSe
Table of Contents
1 Introduction ................................................................... 4
1.1 Product Description...........................................................................4
1.2 Unpacking ........................................................................................4
1.3 Installation Environment....................................................................4
1.4 The Back Panel ................................................................................5
1.5 Connections......................................................................................5
1.6 Front Panel Indicators.......................................................................7
2 Hard Drive Installation................................................... 9
2.1 Opening The DVSe...........................................................................9
2.2 Identifying The Components..............................................................9
2.3 Configuring Master/Slave................................................................10
2.4 Mounting The Hard Drives...............................................................10
2.5 Connecting the Hard Drives.............................................................11
2.6 Compatible Hard Drives ..................................................................12
2.7 Jumper Settings..............................................................................12
3 DVSe Setup .................................................................. 13
3.1 Connecting by SCSI or 1394...........................................................13
3.2 Power-Up .......................................................................................14
3.3 Setup Menu....................................................................................14
3.4 Supervisor Menus...........................................................................16
3.5 Upgrading the DVSe.......................................................................17
4 Warranty and Service .................................................. 19
4.1 Factory Service...............................................................................19
4.2 Warranty.........................................................................................20
Page 4
Kalatel DVSe
4
0150
-
0178
F
1 Introduction
1.1 Product Description
The DVSe is a rack mountable ethernet-ready high capacity digital video storage
system. From 1 to 8 hard drives can be installed in each DVSe chassis. The
unit may be purchased with or without hard drives installed.
1.2 Unpacking
Check the package and contents for visible damage. If any components are
damaged or missing, do not attempt to use the unit. Contact the supplier
immediately. If the unit must be returned, it must be shipped in the original
packaging.
Package Contents
• The DVSe.
• US & EU Power Cables.
• The Kalatel DVSe Installation and Users Manual.
• The Kalatel DVSe Release Note.
• The Archiving Addendum Manual.
• WaveReader Software and Manual.
• WaveWatch Software and Manual.
• IDE Hard Drive Power Connectors x 2. (If shipped without drives installed)
• IDE Hard Drive Connection Ribbon x 4. (If shipped without drives installed)
• Hard Drive Fastening Screws x 24. (If shipped without drives installed)
• SCSI Cable, 50 HD to 50 HD.
• IEEE 1394 Firewire Cable.
1.3 Installation Environment
Power: Ensure that the site’s AC power is stable and within the rated voltage of
the external power supply. Ensure that a reliable Earthing path is maintained.
This unit is designed to be connected to earth ground. If the site’s AC power is
likely to have spikes or dips, use power line conditioning or an Uninterruptable
Power Supply. Do not overload the circuit.
Ventilation: Ensure that the location is well ventilated. Do not obstruct the
cooling vents or fans.
Temperature: Observe the unit’s ambient temperature specifications when
choosing a location for the unit. Extremes of heat or cold beyond the specified
operating temperature limits may cause the unit to fail. Do not install this unit on
top of other hot equipment.
Moisture: Do not expose the unit to rain or moisture. Moisture can damage
internal components. Do not install this unit near sources of water.
Page 5
0150
-
0178
F 5 Kalatel DVSe
Rack Mount: Carefully load the rack so that it remains stable and unlikely to tip
over. The unit is also suitable for desktop installation.
1.4 The Back Panel
ETHERNET
10/100
RELAY
SCSI
IEEE-1394
RS-232SW 1
PORT 1PORT 1 OFF
OFF
1 2 3 4
ON
ON
PORT 2 PORT 2
1: SCSI TERMINATION
2: SCSI POWER
3: BUZZER
4: AUX
1 222 3 4
567
8
Back Panel Components
1. Cooling Fan: Do not obstruct.
2. Power Connector, Voltage Selector and On/Off Switch.
3. IEEE-1394 Firewire Ports 1 and 2.
4. 10/100 Ethernet Port.
5. SCSI Ports 1 and 2.
6. Dip Switches (SW1).
7. RS-232 Port.
8. Alarm Out Relay Connection (Future feature).
1.5 Connections
10/100 Ethernet Port
The Ethernet port is used to connect
the DVSe into a network
environment.
Wire Type: Cat 5.
Connector Type: RJ-45.
Cable Required: Ethernet.
SCSI Ports 1 and 2
Connect a SCSI device to one of the
two SCSI ports. Set the dip switches
(SW1) on the back panel. Set SCSI
Termination and SCSI Power to On
and use the Bus Select menu option
to enable this feature.
Connector: 50 pin, high density SCSI-2.
Gender (on unit): Female.
SCSI ID: 0.
The unit does not currently support multiple SCSI device connections.
Page 6
Kalatel DVSe
6
0150
-
0178
F
Caution! Ensure the power to DVSe is OFF BEFORE
connecting any SCSI or 1394 devices. Do not attempt to use
the SCSI and 1394 ports simultaneously.
1394 Firewire Ports 1 and 2
Connect a 1394 Firewire device to
one of the two 1394 ports. Use the
Bus Select menu option to enable
this feature.
Cable: 6 position IEEE 1394.
Connectors: 6 position DIP.
Dip Switches (SW1)
Set the Dip Switches to enable or
disable the features listed on the
illustration to the right. Switch
position up to turn off (disable), down
to turn on (enable).
OFF
1 2 3 4
ON
1: SCSI TERMINATION
2: SCSI POWER
3: BUZZER
4: AUX
RS-232 Port
The RS-232 port can be used for
Serial Debugging.
Connector Type: DB-9.
Gender (on unit): Male.
Cable Required: Null Modem.
DB-9 Pin Configuration For RS-232 Port
Pin Use Pin Use
1 DCD 6 Not Connected
2 RX 7 RTS
3 TX 8 CTS
4 Not Connected 9 Not Connected
5 Ground
To receive serial debug data from the DVSe’s RS-232 port, set up the
receiving serial port at 57600 bps, No Parity, 8 data bits, and 1 stop
bit.
NOTE
Page 7
0150
-
0178
F 7 Kalatel DVSe
1.6 Front Panel Indicators
ACTIVITYPWR
1 2 3 4 5 6 7 8 LNK RD WR 100
ETHERNET
STATUS
HARD DRIVES
1
222
3
5
4
Kalatel DVSe
e
1. Power LED.
2. Hard Drive Status Indicators.
3. Ethernet Indicators.
4. LCD Display.
5. Key Pad buttons.
Hard Drive Status Indicators (Green LEDs)
LED On: Drive present and operating normally.
LED Off: No drive present, drive not detected, drive disabled due to error.
Hard Drive Activity Indicators (Red LEDs)
The LED blinks when the drive is being accessed (read or write).
Ethernet Indicators
The ethernet LEDs light to indicate the following:
• Link: A detected ethernet connection.
• RD: Receiving Data.
• WR: Transmitting Data.
• 100: 100 Mbps bandwidth
LNK RD WR 100
ETHERNET
LCD Display
Once power-up is complete, the LCD
displays the total disk storage capacity of the
unit. The LCD display also provides visual
feedback for the menu settings. See DVSe
Menu Setup for details.
Page 8
Kalatel DVSe
8
0150
-
0178
F
Key Pad
The Key Pad buttons provide access and control of the Setup Menu.
• Up Arrow: Change field data (ascending).
• Left Arrow: Move field selection to left.
• Enter Button: Press to access setup
menu. Toggles through menu screens.
• Right Arrow: Move field selection to right.
• Down Arrow: Change field data
(descending).
Page 9
0150
-
0178
F 9 Kalatel DVSe
2 Hard Drive Installation
This section contains important information on adding or replacing the internal
Disk Drives. Please read the entire section before performing any work.
Caution: Do not allow any metal object to contact the
motherboard. Do not allow loose screws to become lost inside
the DVSe chassis. Wear an Electro Static Discharge protection
device any time work is being performed inside the unit.
2.1 Opening The DVSe
Before removing the cover, turn off the unit and unplug it. Using a Phillips-head
screwdriver, carefully remove the twelve screws fastening the lid to the chassis.
Save the screws and use them to refasten the lid when finished.
2.2 Identifying The Components
Complete Internal Overview
Mother
Board
Disk Drives
Power
Supply
Drive Support Bracket
Page 10
Kalatel DVSe
10
0150
-
0178
F
Motherboard Overview
IDE Power
Connectors
IDE
Connectors
Power
Supply
Load
Resistors
Jumpers
2.3 Configuring Master/Slave
Hard drives are connected in pairs to
each of the four IDE connectors. Each
pair of hard drives must be configured
as a Master and a Slave. Configure
the Master/Slave settings on each hard
drive individually using the jumpers
provided with the drive. Use the
diagram located on the hard drive to
determine the proper jumper
configuration.
If a single drive is connected to an IDE
connector, it must be configured as a
Master.
IDE Connector #1
IDE Connector #2
IDE Connector #3
IDE Connector #4
Disk 1
Master
Disk 2
Slave
Disk 3
Master
Disk 4
Slave
Disk 5
Master
2.4 Mounting The Hard Drives
Remove the Hard Drive Support Bracket. This entails removing the screws at
either end and one screw from each installed hard drive.
Orient the hard drive so that the IDE Power Connector is near the bottom of the
chassis and facing the motherboard. Populate the drive array in order, starting
from the left.
Fasten the drive in place using the supplied screws. Fasten each drive using two
screws through the bottom of the chassis and one screw in the Hard Drive
Support Bracket.
Page 11
0150
-
0178
F 11 Kalatel DVSe
2.5 Connecting the Hard Drives
Power Supply Cables
It is recommended, for ease of installation, that the IDE and power
cables be first connected to the drives before the drive screws are
tightened.
Connect the hard
drives to the power
supply connectors
with power supply
cables.
When connecting a
single drive to a
cable, attach the
drive to the
connector at the end
of the power cable.
Disk 1
Disk 2
Disk 3
Disk 4
Disk 5
Disk 6
Disk 7
Disk 8
Power Supply
Mother Board
The diagram above shows a typical connection. The connections
may vary according to the number of drives in the system and the
power cable type.
IDE Data Cables
Use an IDE cable to connect the drives as shown in the diagram in section 2.3.
When attaching the IDE connector, make sure the connectors are oriented
properly.
Connecting To The Motherboard
The red stripe on the connection ribbon
should connect nearest the Pin 1 indicator
on the motherboard.
Pin 1
Indicator
Connecting To The Hard Drive
The red stripe on the connection ribbon
should connect near the jumpers on the hard
drive.
Pin 1 Near
Jumpers
NOTE
NOTE
Page 12
Kalatel DVSe
12
0150
-
0178
F
2.6 Compatible Hard Drives
The DVSe is designed to be compatible with Maxtor D540X series hard drives.
Hard drives in this series up to 250 GB may be used. Refer to www.maxtor.com
for details.
GE Interlogix cannot provide technical support for DVSe units using
hard drives other than those described above. Using drives other
than those described above may result in failure or intermittent data
errors.
Please contact GE Interlogix technical support regarding hard disk
compatibility.
2.7 Jumper Settings
Jumper Configuration
Configure the jumpers based on the number of hard drives installed in the unit.
Do not throw away unused jumpers.
See section 2.2 to locate this block of jumpers.
1-7 Drives 8 Drives
Load 4
Load 3
Load 2
Load 1
Load 4
Load 3
Load 2
Load 1
After any drives are installed, replaced or removed, the Reset Disk
Failure command must be run from the Supervisor Menu for the
changes to be recognized by the DVSe.
NOTE
NOTE
Page 13
0150
-
0178
F 13 Kalatel DVSe
3 DVSe Setup
This section contains important information on setting up the DVSe for
operation. Please read the entire section before performing any work.
3.1 Connecting by SCSI or 1394
Caution! The DVSe does NOT support the simultaneous use
of the SCSI and 1394 ports. Only connect one type of device at
a time.
SCSI
Connect a SCSI device to one of the two SCSI ports using the supplied SCSI
cable. Set the dip switches (SW1) on the back panel. Set SCSI Termination
and SCSI Power to On. Select SCSI as the type of Bus in the Setup Menu
under Bus Select.
Caution! Power must be shut down before connecting SCSI
cables between SCSI devices and the DVSe.
Dip Switches (SW1)
Set the Dip Switches to enable or
disable the features listed on the
illustration to the right. Switch
position up to turn off (disable), down
to turn on (enable).
OFF
1 2 3 4
ON
1: SCSI TERMINATION
2: SCSI POWER
3: BUZZER
4: AUX
1394 Firewire
Connect a 1394 device to one of the two 1394 ports using the supplied 1394
cable. Set the dip switches (SW1) on the back panel. Set SCSI Termination
and SCSI Power to OFF. Select 1394 as the type of Bus in the Setup Menu
under Bus Select.
Caution! Power must be shut down to all devices before
connecting 1394 cables between the 1394 device and the
DVSe.
Page 14
Kalatel DVSe
14
0150
-
0178
F
3.2 Power-Up
Select the correct voltage before supplying power to the unit. Use the voltage
selector switch located on the back panel of the unit, between the power
connector and the On/Off Switch.
Caution! Applying incorrect voltage could damage unit.
Once the correct voltage has been selected and all connections have been
made, connect the power cable suited to your geographic location. Apply power
to the unit.
3.3 Setup Menu
The Setup menu provides setup options for the following features:
• Ethernet enable/disable.
• Bus Select: SCSI/1394
• Auto Delete Mode.
• IP Address.
• Subnet Mask Address.
• Default Gateway Address.
• Date/Time Setup.
Menus will automatically be exited after 30 seconds of inactivity.
Access to menu is only allowed when the DVSe is Offline, i.e. the
DVSe is not presently archiving or connected via ethernet.
Press the Enter Button to access the first menu.
Ethernet Enable
Select ethernet enable, yes or no. Default
setting is no.
Bus Select
Select from SCSI or 1394 to enable. Default
setting is 1394.
NOTE
NOTE
Page 15
0150
-
0178
F 15 Kalatel DVSe
Auto Delete Mode
Auto Delete Mode, select yes or no. Default
setting is no. Auto Delete Mode
automatically invalidates data that is over 30
days old.
Obtain the required network addresses from you Network
Administrator.
The DVSe will automatically reboot if any of the Bus or Network
parameters are changed.
IP Address
Enter the assigned IP address by using the
left/right arrows to select the field and the
up/down arrows to change the values.
Subnet Mask
Enter the assigned Subnet Mask address by
using the left/right arrows to select the field
and the up/down arrows to change the
values.
Default Gateway
Enter the assigned Default Gateway address
by using the left/right arrows to select the
field and the up/down arrows to change the
values.
Date/Time
Enter the current date and time by using the
left/right arrows to select the field and the
up/down arrows to change the values.
Required only when Auto Delete Mode is set
to yes.
NOTE
NOTE
Page 16
Kalatel DVSe
16
0150
-
0178
F
3.4 Supervisor Menus
The Supervisor menus provides advanced options for the following features:
• Serial Debug Output.
• Disk Status.
• Disk Failure Reset.
The Key Pad buttons provides access and control of the Supervisor Menus. To
access the Supervisor menus press the left and right arrows simultaneously.
• Up Arrow: Quits the menu.
• Left Arrow: Move field selection to left.
• Enter Button: Press to access setup
menu. Toggles through menu screens.
• Right Arrow: Move field selection to right.
• Down Arrow: Quits the menu.
Serial Debug
Serial Debug output, select yes or no.
Default setting is no. Enabling serial debug
will output debug messages on the RS232
port at 57600 bps. Changing this setting will
cause the unit to restart.
Disk Status
This menu indicates the current disk status.
Disk status is viewable only on this display.
• N: Normal
• W: Error writing to Disk
• R: Error Reading Disk
• T: Timeout during disk initialization or disk
absent
The letters on the Disk Status screen represent Disk 1 (left) thru Disk 8 (right).
Do not attempt to reset a disk with read/write errors (a R or W
status). This could lead to more disk errors and data loss. Disks
with read/write errors should be replaced.
NOTE
Page 17
0150
-
0178
F 17 Kalatel DVSe
Disks with a T status may be recovered, but the DVSe will
attempt to start recording to this disk. A recovery should not be
attempted until the preceding disk is filled up. Contact Technical
Support for detailed instructions on replacing or recovering
problem hard disks.
Be sure to confirm that the drives are connected according to the
diagram in Section 2.3 before removing or replacing. The disk
status display and LEDs represent the wiring and Master/Slave
configuration, not the physical location of the drives.
Reset Disk Failure
This command allows the DVSe to re-enable
disks with timeout errors and reset the Disk
Status. Changing this setting restart the unit.
Any time that a disk is replaced, added, or
removed this command must be executed.
3.5 Upgrading the DVSe
Upgrading the software for the DVSe is accomplished via the ethernet port
and a PC/Laptop equipped with a web browser.
To properly upgrade the Kalatel DVSe the following preconditions must exist:
1. The Flash upgrade file and path. This file is obtained by calling Kalatel
Technical Support at 1-800-469-1676. When calling, please have the
following information available:
q The model number of the product.
q The serial number and revision of the product
q The current firmware version.
q The date purchased.
q Symptoms of the unit that might require upgrade.
2. The DVSe unit connected to a PC equipped with Microsoft Internet
Explorer version 5.5 or later via ethernet cable.
3. The IP address of the DVSe.
4. WaveReader software must NOT be connected to the DVSe. Please
exit all non-essential software on the PC.
NOTE
NOTE
Page 18
Kalatel DVSe
18
0150
-
0178
F
5. Ensure that the DVSe is not currently recording or archiving.
Follow the steps below to Upgrade the DVSe:
Step 1. Launch the Browser software (Microsoft Internet Explorer 5.5 or
later).
Step 2. Enter the IP address of the DVSe in the address field of the Browser
followed by /upgrade.ssi and press enter. For example if the IP
address is 3.18.173.71 type 3.18.173.71/upgrade.ssi.
Step 3. The Enter Network Password window should appear. Enter the
correct Username and Password in their respective fields. (The
default username is admin and the password is admin. It is
recommended that the defaults be changed ASAP). Click the OK
button. The DVSe upgrade page should appear.
Step 4. Navigate to the upgrade file using the Browse button or type in the
correct path and filename. Click on the Send File button.
Step 5. Click on the Confirm Button. A progress bar will appear. PLEASE
WAIT FOR THE PROGRESS BAR TO FINISH, THEN WAIT FOR
CONFIRMATION!
Step 6. Click on the Reboot button to restart the unit for changes to take
effect. If unsuccessful, download the flash file again and retry the
steps 1-6.
Page 19
0150
-
0178
F 19 Kalatel DVSe
4 Warranty and Service
4.1 Factory Service
If the unit requires factory service, contact the dealer who supplied the unit to you for the
correct procedures on returning the unit to the factory or the nearest factory service center.
If the dealer is not available, contact the manufacturer of the unit as detailed below and
request a Return Material Authorization number (RMA). The unit’s serial number must be
provided before an RMA number can be issued. Units returned to the factory for service
must have freight and insurance prepaid, and must show the RMA number clearly on all
shipping documents. The failure symptoms must be clearly described by the operator and
enclosed with the unit together with a copy of the original supplier’s invoice. Failure to
comply with these instructions will delay service of the unit, and may result in the unit not
being accepted by the Repair Center.
Factory Address
GE Interlogix
Attention: Repair Center
3197-C Airport Loop Drive
Costa Mesa, CA 92626
United States of America
Telephone: 800-343-3358 (7:00 AM to 4:30 PM, Pacific Time)
In Oregon: 541-754-9133
Fax: 541-754-7162 (24 hours a day)
For warranty information, see the following page.
Page 20
Kalatel DVSe
20
0150
-
0178
F
4.2 Warranty
GE Interlogix warrants all of its equipment for three years from the date of purchase. This
warranty covers any defects in materials and workmanship. Equipment failures that are due
to improper installation, modification, abuse, or acts of nature will not be covered by this
warranty. The repair department will evaluate all equipment returned for repair to determine
warranty coverage. The Tech Support Manager will resolve any questions that may arise
during evaluation to make a final determination.
Note: The three-year warranty does not apply to the following products:
MobileView® and the monitor CRT, which carry a 12-month warranty from the date of
purchase.
The warranty specifically covers any defects in material and workmanship and does not
cover equipment that has been abused, damaged, or modified.
For all warranty repairs, GE Interlogix will cover all costs, including parts, labor, and
shipping. Repaired equipment will be returned via the same method of shipment in which it
was received. If a customer requests a faster return shipment, the difference will be
charged.
For all non-warranty repairs, the customer will be billed for parts, labor, and shipping.
Labor will be billed in half-hour increments.
Note: Customers requesting an estimate prior to repair will be notified by phone. If they
cannot be reached, they will be notified by fax. If we are unable to reach the contact person
for repair authorization after one phone attempt and two fax attempts, the equipment will be
returned without being repaired. We will hold equipment no longer than two weeks.
Advance Replacement Policy
When an advance replacement is required, we will send the customer replacement
equipment from our stock and receive the returned product in exchange. The received
equipment will be evaluated and the repair department will determine whether it is a
warranty replacement. If it is non-warranty, see our repair policy above for details. The
following guidelines will be used for all advance replacements:
• Fewer than 45 days from purchase, GE Interlogix will replace the product with new
equipment.
• From 45 days to 1 year from purchase, GE Interlogix will replace the product with
refurbished equipment.
• From 1 year to 3 years from purchase, the product must be sent in for repair.
Advance replacements will be sent for a fee of $100.
If you have questions about this policy, please contact the GE Interlogix RMA Department
at 800-469-1676.
Loading...