EXT-DVI-FM1000
P
s
e
a
w
®
r Man
l
ww.gefen.co
T
t
0
0
(
0
T
:
8
e
:
C
c/
e
0600
1
s
e
y
f Gef
C
©
y of
ASKING FOR ASSISTANC
E
3
echnical Suppor
Telephone (818) 772-910
(800) 545-690
Fax
echnical Support Hours
:00 AM to 5:00 PM Monday through Friday, Pacifi c Tim
Write To
efen LL
o Customer Servic
2
www.gefen.com
Nordhoff St
hatsworth, CA 9131
upport@gefen.com
818) 772-912
Notic
efen, LLC reserves the right to make changes in the hard ware, packaging, and
accompanying doc u men ta tion without prior written notice.
an
VI FM 1000 PLUS is a trademark o
2012 Gefen, LLC. All rights reserved.
All trademarks are the propert
their respective owners.
en, LL
Rev A
S
1 Intr
oduction
O
3
S
t
5 S
6
t
8 C
S
8
9
g
y
CONTENT
2
4
7 Receiver Descriptions
10 Specifi cations
11 Warrant
peration Notes
Features
ender Layou
ender Descriptions
Receiver Layou
onnecting the DVI FM 1000 PLU
Wiring Diagram
EDID Programmin
INTRODUCTIO
N
s
g
sy
g
T
S
000
y
f SC
e
y f
S
y
c
ongratulations on your purchase of the DVI FM 1000 PLUS. Your complete
atisfaction is very important to us.
efen
efen delivers innovative, progressive computer and electronics add-on solutions
that harness inte
efen’s reliable, plug-and-play products supplement cross-platform computer
stems, professional audio/video environments and HDTV systems of all sizes
with hard-workin
he Gefen DVI FM 1000 PLU
ration, extension, distribution and conversion technologies.
solutions that are easy to implement and simple to operate.
The DVI FM 1
DVI source to a displa
o
-terminated multimode fi ber optic cable. Automatic EDID Programming
nables quick integration of the video source to the display. The optical signal
transmission provides immunit
How It Works
The
a DVI displa
ender module plugs into a DVI source. The Receiver module plugs into
onnects the Sender to the Receiver module.
Plus extender uses two small transceivers to extend a
up to 3300 feet (1000 meters) using a single-strand
rom electromagnetic interference (EMI).
. A single strand of multimode SC-terminated fi ber optic cable
S
S
y
S
c
y
62.5/125
f
2
OPERATION NOTES
:
t
READ THESE NOTE
BEFORE INSTALLING OR OPERATING THE DVI FM 1000 PLU
• The DVI FM 1000 PLUS only uses a multi-mode SC fi ber optic cable.
ATTENTION
of 50/125 is required, in order to extend to distance of 3300 fee
1000 meters).
• The supplied power adapter must onl
Power to the
ender module is supplied by the source through the DVI
Multi-mode fi ber optic cable with a core diameter
be used on the Receiving module.
onnector. If the LED on the Sender module does not activate when
the source is connected and powered, an external power suppl
.
•
to 1000
μm (OM1) fi ber may also be used at reduced maximum range of up
eet (300 meters).
will be
3
S
Features
f
)
e
e
)
y
n
e
e
y
e
FEATURE
• Extends DVI up to 3300
ultimode fi ber optic cabl
• Extends DVI up to 1000 feet (300 meters) over a single-strand of OM1
62.5/125μm) multimode fi ber optic cabl
•
• Automatic EDID programming provides continuous connection of source to
•
•
upports resolutions up to 1920 x 1200 (WUXGA
displa
turdy die-cast metal enclosures provide a robust solution for professional
and industrial applications
ompact Sender and Receiver modules provide a clean, easy installatio
ackage Includes
1) DVI FM 1000 PLUS - Sender Modul
1) DVI FM 1000 PLUS - Receiver Modul
1) 5V DC Power Suppl
1) Quick Start Guid
eet (1 km) over a single-strand of OM2 (50/125μm
4
SENDER LAYOU
T
t
3
4
Fron
Back
t
3
e
C
y
r
SENDER DESCRIPTION
S
DVI Inpu
onnect this part of the Sender module to the DVI port on the computer.
SC Fiber Connector
onnect an SC fi ber optic cable from the Sender to the Receiver module.
ower Receptacl
If the source does not supply enough voltage to power the Sender module,
connect a 5V D
suppl
This LED will glow bright green when the Sender module is powered. It is also
will not be required.
tatus Indicato
sed to indicate the status of the Sender module when programming the EDID.
ee page 9 for details.
power supply to this receptacle. In most situations, the power
5
RECEIVER LAYOU
T
t
3
Fron
Back
RECEIVER DESCRIPTION
S
t
3
e
r
DVI Outpu
onnect this part of the Receiver module to a dual-link DVI display.
SC Fiber Connector
onnect an SC fi ber optic cable from the Receiver to the Sender module.
ower Receptacl
onnect the included 5V DC power supply to this receptacle.
tatus Indicato
This LED will glow bright green when the Receiver module is powered.
7
CONNECTING THE DVI FM 1000 PLUS
S
3
g
S
How to Connect the DVI FM Extender PLU
1.
2.
.
optic cable.
4.
onnect a dual-link DVI source to the Sender module.
onnect a dual-link DVI display to the Receiver module.
onnect the Sender to the Receiver module using an SC multimode fi ber
onnect the 5V DC power supply to the Receiver module.
Wirin
DVI Source
Diagram for the DVI FM 1000 PLU
SC FIBER OPTIC CABLE
(up to 3,300 feet)
Transmitter
Receiver
DVI Display
EXT-DVI-FM1000P
e
y
f
g
y
3
f
fl
y f
9
DID PROGRAMMIN
G
DID Programming Procedur
Display information (EDID) contains resolution and timing information for your
displa
these steps to record the EDID o
will not be necessary.
. This information is needed by the source for proper video output. Follow
the display into the Sender module. If you
now that EDID is not required by the source, the followings steps for recordin
1.
2. Power on the displa
4. Disconnect the power suppl
onnect the Sender module to a display.
.
.
onnect the included 5V DC power supply into the Sender module.
The LED on the back o
ashing and is solid, the displays EDID will have been successfully recorded.
the module will fl ash rapidly. Once the LED stops
rom the Sender module then from the display.
SPECIFICATION
S
z
e
e
SC
C
)
C)
C)
g
)
g)
aximum Pixel Clock................................................................................165 MH
Video Input Connector (Sender)................................. (1) DVI-D (24 pin), mal
Video Output Connector (Receiver).................................. (1) DVI-D (24 pin), mal
Link Connector (Sender / Receiver).............................................. (1) Type
Power Supply (Receiver)...............................................................................5V D
Power Consumption...................................................................... 2.5 Watts (max.
perating Temperature............................................ +32° to +122°F (0° to +50°
torage Temperature.............................................. -4° to +158°F ( -20° to +70°
elative Humidity......................................................10% to 80%, non-condensin
Dimensions.......................(W x H x D): 1.6” x 0.6” x 2.8” (40mm x 14mm x 70mm
hipping Weight:................................................................................ 1 lb (0.45 k
10
1
efen warrants the equipment it manufactures to be free from defects in material
f
y
e
e
f
eff
y of
y
y
f of
3
g
f
Gef
y
g
y
g
s
y
y
N
.
and workmanship.
I
equipment fails because of such defects and Gefen is notifi ed within two (2)
ears from the date of shipment, Gefen will, at its option, repair or replace the
quipment, provided that the equipment has not been subjected to mechanical,
lectrical, or other abuse or modifi cations. Equipment that fails under conditions
other than those covered will be repaired at the current price o
ect at the time of repair. Such repairs are warranted for ninety (90) days from
the da
reshipment to the Buyer.
parts and labor in
This warrant
without limitation, an
articular purpose, all of which are expressly disclaimed.
1. Proo
2.
The in
be accurate. However,
that ma
direct, indirect, special, incidental, or consequential dama
an
dama
For the latest warrant
Polic
ustomers outside the US are responsible for shipping charges to and from
efen.
.
opper cables are limited to a 30 day warranty and cables must be in their
ori
ormation in this manual has been carefully checked and is believed to
defect or omission in this manual, even if advised of the possibility of such
es. The technical information contained herein regarding the features and
pecifi cations is subject to change without notice.
under the Support section of the Gefen Web site at www.gefen.com.
is in lieu of all other warranties expressed or implied, including
implied warranty or merchantability or fi tness for any
sale may be required in order to claim warranty.
inal condition.
en assumes no responsibility for any inaccuracies
be contained in this manual. In no event will Gefen be liable for
es resulting from
coverage information, refer to the Warranty and Return
RODUCT REGISTRATIO
lease register your product online by visiting the Register Product page
nder the Support section of the Gefen Web site
1
Rev A
3
1
800
6900
20
m
Nordhoff St., Chatsworth CA 9131
1-
-545-
www.gefen.com support@gefen.co
818-772-9100 fax: 818-772-91
Pb
This product uses UL or CE listed power supplies.
Loading...