GEFEN EXT-DVI-2-HDSDIPRO EXT-DVI-2-HDSDIPRO.pdf

Page 1
®
DVI to HD-SDI
Scaler Pro
USER MANUAL
www.gefen.com
Page 2
ASKING FOR ASSISTANCE
Technical Support:
Telephone (818) 772-9100 (800) 545-6900
Technical Support Hours:
8:00 AM to 5:00 PM Monday through Friday Pacifi c Time
Write To:
Gefen Inc. C/O Customer Service 20600 Nordhoff Street Chatsworth, CA 91311
www.gefen.com support@gefen.com
Notice
Gefen LLC reserves the right to make changes in the hard ware, packaging and any
accompanying doc u men ta tion without prior written notice.
The DVI to HDSDI PRO is a trademark of Gefen LLC
All trademarks are the property of their respective owners.
© 2010 Gefen Inc., All Rights Reserved
Rev X2
Page 3
TABLE OF CONTENTS
Introduction
1
Operation Notes
2
Panel Descriptions
3
Menu Functions
4
Supported Input/Output Resolutions
6
RMT-8HDS-IR Installation
7
RS-232 Control and Firmware Update Procedure
8
Specifi cations
9
Warranty
10
Page 4
INTRODUCTION
The Gefen DVI to HDSDI Pro Scaler combines two of our DVI to HDSDI Scaler Plus units into one rack-mountable unit. It still incorporates full single-link DVI-D conversion scaled to your choice of SD/HDSDI Single- or Dual-link modes, but now simplifi es your rack. Resolutions of up to 1080p are supported over the HDSDI link for those that want true “High Defi nition.” Performance has been greatly enhanced due to Gennum’s VXP Scaler circuitry onboard, allowing for new features such as Genlock, Color & Gamma Correction, Noise Reduction, Detail Enhancement, Aspect Ratio Selection, Pattern Generator Mode, and Multiple Language Menu Support. Bottom Line? More performance, less cost.
HOW IT WORKS
DVI devices are connected to the DVI inputs and SDI devices are connected to the SDI outputs. When the source, display and the Scaler are powered and connected, video signals are converted to the proper format. There are two separate menu systems for each integrated DVI to HDSDI box. Input 1 is labeled as the Master device in the menu system while Input 2 is labeled as the Slave device. Please refer to page 2 on how to access each separate menu system
CONTENTS
The DVI to HD-SDI Pro consists of: (1) DVI to HDSDI Pro Scaler unit
(2) 6 foot DVI Cable (m-m) (1) RMT-8HDS-IR Remote Control (1) 5V Universal DC Power Supply (1) User's Manual
1
Page 5
OPERATION NOTES
On power up, the DVI to HD-SDI Pro will automatically detect the format of the input signal. The unit is controlled using the included remote or through the RS-232 port.
The following are the buttons for the RMT-8HDS-IR Remote Control Unit (included):
- UP (Navigates cursor up)
- LEFT (Navigates cursor left)
- Enter (Accept Operation / Return to Menu)
- RIGHT (Navigates cursor right)
- DOWN (Navigates cursor down)
- MENU (Show / Hide On screen Display)
- OUTPUT (Change Output Format)
- SOURCE (Non operational) To bring up the on screen menu for the master device, press the MENU button once.
To bring up the menu for the slave device, press the MENU button again. Pressing the MENU button once more will exit the menu system. Navigation is done using Buttons up, left, right, and down; Push the Enter button to accept the cursor focus.
Pressing the Output button cycles through the following output modes: 480i - 576i - 720p - 1080i
Other functions and output modes can be accessed through the on screen menu. To Restore I/O settings, simply recycle power on the Scaler
*Note: The IR Remote Control Unit has a small bank of adjustment switches known as DIP (Dual Inline Package) switches located inside the battery compartment. Both DIP switches under the remote battery cover must initially be in the OFF position to communicate with the Scaler, as they control the IR frequency used. Please see page 7 for more information on how to set the DIP switches.
Front
RMT-8HDS-IR
Remote Control
Unit
DIP
switches
2
Back
Page 6
PANEL DESCRIPTIONS
Front
RS-232
5V
Power Input
Port 1
DVI
Input 1
HD-SDI
Output 1
GenLock
Reference
Input 1
HD-SDI
Output 2
Back
IR Receiver 2IR Receiver 1
Power LED
Indicator
RS-232
Port 2
HD-SDI
Output 1
DVI
Input 2
GenLock
HD-SDI
Output 2
Reference
Input 2
DVI to HDSDI Unit 1 DVI to HDSDI Unit 2
3
Page 7
Menu Functions
Aspect:
-Full Screen: Stretches input to fi ll the Monitor.
-Letter / Pillar Box: Sets the aspect ratio to fi t a letter or pillar box format.
-Panoramic: Panoramic Zoom feature
-Extract: Feature to magnify the signal.
-Extract Size: Adjusts signal magnifi cation.
-Horizontal / Vertical Position: Moves the magnifi ed signal Horizontally and Vertically
-Through: Feature to crop the signal.
-Horizontal / Vertical Size: Horizontally and Vertically contracts or expands the cropping viewport.
-Horizontal / Vertical Position: Move the signal Horizontally or Vertically inside the cropping viewport.
Layout:
-Size and Position:
-Horizontal / Vertical Size: Adjust Horizontal or Vertical resolution.
-Horizontal / Vertical Position: Move image Horizontally or Vertically.
Picture:
-Image Color:
-Contrast: Individually adjust the contrast for red, green and blue
-Brightness: Individually adjust the brightness for red, green and blue
-Black level: Adjust black levels between 0 (default) and 100
-Detail Enhancement:
-Detail Enhancement: Digitally enhance signal
-Noise Threshold: Adjusts noise allowed in detail enhancement
-Noise Reduction: Digitally reduce signal noise
-Motion Threshold
4
Page 8
Menu Functions (continued...)
Input:
-Input Video Format: Auto Detect by default. Signal can be forced to a specifi c High-defi nition resolution. (Please see Supported Input/Output Resolutions for more information).
-Input Graphic Format: Auto Detect by default. Signal can be forced to a specifi c computer resolution. (Please see Supported Input/Output Resolutions for more information).
-Clean Aperture:
-Horizontal and Vertical Size: Stretch image Horizontally or Vertically
-Horizontal and Vertical Position: Move image in view port Horizontally or Vertically
-Non-standard sync
-Remote Channel: Changes the IR code of the DVI to HDSDI Scaler to one of 4 different settings between 0 and 3. When the remote channel is changed, dip switches in the remote must be changed to the corresponding code in order to continue operating the DVI to HDSDI Scaler.
(Please see RMT-8HDS-IR Installation page for more information.) Output:
-Output Format: Select the desired output resolution. (Please see Supported Input/Output Resolutions for more information).
-Link Confi guration
-Genlock Reference: Locks input clock in sync with output clock. 2 locking methods by either the DVI input or the Reference input. (Note: feature only works if input and output frequencies are multiples of each other)
-Language: Set menu to display English or French text.
-Gamma Correction:
-Default: Set for Default Gamma settings.
-sRGB
-Custom: Enables Gamma Coeffi cient menu item as the current Gamma coeffi cient.
-Gamma Coeffi cient: (0.3 - 3.0); Default set at 1.0. Patterns:
-Color Bars: Display color bar video pattern.
-Cross Hatch: Display cross hatch video pattern. General:
-Save confi guration
-Restore default confi guration
5
Page 9
SUPPORTED INPUT/OUTPUT RESOLUTIONS
Input Video Formats Supported:
480i 10305i/59.94 1080p/50M 480p 1035i/60 1080p/59.94 576i 1080i/50 1080p/60 576p 1080i/50M 1080sf/23.98 720p/23.98 1080i/59.94 1080sf/24 720p/24 1080i/60 1080sf/25 720p/25 1080p/23.98 1080sf/29.97 720p/29.97 1080p/24 1080sf/30 720p/30 1080p/25 2K-p/23.98 720p/50 1080p/29.97 2K-p/24 720p/59.94 1080p/30 2K-sf/23.98 720p/60 1080p/50 2K-sf/24
Input Graphic Format Supported:
640x350/85 1024x768/85 1366x768/60 640x400/85 1280x854 1366x923/50 640x480/60 1152x864/75 1440x900/60 640x480/75 1280x768/60 1440x1080/60 640x480/85 1280x960/60 1440x1080/60 800x600/60 1280x960/85 1600x1024 800x600/75 1280x1024/60 1600x1200/60 800x600/85 1280x1024/75 1680x1050/60 1024x768/60 1280x1024/85 1920x1200/60 1024x768/75 1360x768/60 2048x1080
Output video formats supported:
480i 10305i/59.94 1080p/50M 480p 1035i/60 1080p/59.94 576i 1080i/50 1080p/60 576p 1080i/50M 1080sf/23.98 720p/23.98 1080i/59.94 1080sf/24 720p/24 1080i/60 1080sf/25 720p/25 1080p/23.98 1080sf/29.97 720p/29.97 1080p/24 1080sf/30 720p/30 1080p/25 2K-p/23.98 720p/50 1080p/29.97 2K-p/24 720p/59.94 1080p/30 2K-sf/23.98 720p/60 1080p/50 2K-sf/24
6
Page 10
RMT-8HDS-IR Installation
1. Remove battery cover from the back of the RMT-8HDS-IR remote.
2. Verify that DIP switches 1 & 2 are in the down (OFF) position.
3. Insert the battery, hold the battery so that you can see the positive side facing up. The side that is not marked must be facing down.
4. Test the RMT-8HDS-IR remote by pressing ONLY one button at a time. The indi­cator light on the remote will fl ash once each time you press a button. WARNING: Do not press multiple buttons simultaneously and do NOT press buttons rapidly. These actions will cause the remote to reset and steps 1-4 will have to be repeated.
Note: The RMT-8HDS-IR ships with two batteries. One battery is required for opera­tion, the second battery is a spare.
The following are the DIP switch combinations that correspond to the Remote Code menu option on the DVI to HDSDI Scaler (Please see Menu Functions section for more information):
Remote Channel 0:
Remote Channel 2:
Battery Compartment
Remote Channel 1:
1
1
2
2
Remote Channel 3:
1
1
2
2
DIP Switches
RMT-8HDS-IR Remote Control Unit (Back)
7
Page 11
RS-232 CONTROL
The DVI to HD-SDI Pro can be controlled via the RS-232 port on the rear of the unit. Please refer to the Communication Protocol for Gennum VXP Products on Gefen’s website at: http://www.gefen.com/kvm/support/download.jsp.
FIRMWARE UPDATE PROCEDURE
1 Connect your computer’s RS-232 (serial) port to the RS-232 port on the DVI to HD-SDI Scaler Pro using a male to female, straight pin-to-pin RS-232 cable. Do not use a null modem cable.
2 Please download the latest fi rmware from Gefen’s website at: http://www.gefen.com/kvm/support/download.jsp
3 Open and edit the setup.bat fi le and on the line “set comport=” edit the port number to match your comport number.
4 Run the setup.bat batch fi le and follow the instructions
8
Page 12
SPECIFICATIONS
Input Video Bandwidth............................................................................. 2 x 165 MHz
Output Video Bandwidth...........................................................................4 x 165 MHz
Maximum Input Resolution..........................................................................2048x1080
Maximum Output Resolution.................................................................2048x1080p24
DVI Connector...........................................................DVI-I 29 pin female (digital only)
SDI/HDSDI Connector...............................................................................BNC female
Data Port................................................................................................Serial RS-232
Power Supply................................................................................................5V 8A DC
Power Consumption.............................................................................20 watts (Max.)
Dimensions..................................................................................6.5”W x 1”H x 6.75”H
Shipping Weight...................................................................................................5 lbs.
9
Page 13
WARRANTY
Gef
f
y
e
e
eff
p
Gef
3
s
pag
p
N
en warrants the equipment it manufactures to be free from defects in material
and workmanship. I
equipment fails because of such defects and Gefen is notifi ed within two (2) ears from the date of shipment, Gefen will, at its option, repair or replace the quipment, provided that the equipment has not been subjected to mechanical, lectrical, or other abuse or modifi cations. Equipment that fails under conditions
other than those covered will be repaired at the current price of parts and labor in
ect at the time of repair. Such repairs are warranted for ninety (90) days from
the day of reshipment to the Buyer. This warranty is in lieu of all other warranties expressed or implied, including
without limitation, any implied warranty or merchantability or fi tness for any
articular purpose, all of which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2.Customers outside the US are responsible for shipping charges to and from en.
.Copper cables are limited to a 30 day warranty and cables must be in their
original condition.
The information in this manual has been carefully checked and is believed to be accurate. However, Gefen assumes no responsibility for any inaccuracies that may be contained in this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. The technical information contained herein regarding the features and
pecifi cations is subject to change without notice.
For the latest warranty coverage information, please visit Gefen’s Warranty web
e at http://www.gefen.com/kvm/aboutus/warranty.js
RODUCT REGISTRATIO
lease register your product online by visiting Gefen’s web site at
http://www.gefen.com/kvm/Registry/Registration.jsp
10
Page 14
Page 15
Rev X2
b
20600 Nordhoff St., Chatsworth CA 91311
1-800-545-6900 818-772-9100 fax: 818-772-9120
www.gefen.com support@gefen.com
P
Loading...