Geemarc Large Display Alarm Clock User Manual
Wakenshake gti
Large display alarm clock with shaker
Réveil grand écran avec vibreur
GB
User guide p.2
F
Notice d’utilisation p.12
A l a r m C l o c k
2
DESCRIPTION
PM
AL
Alarm mode switch
Snooze key / Flash
PM LED indicator
Alarm LED indicator
Shaker Lo / Hi switch
Alarm + ring / Off / Ring function
switch
Alarm and ring
volume
Set alarm
Set clock
(*) Modular jack
(*) Classified TVN-3 according to EN60950 standard.
3
3
Alarm tone
Alarm off for 24H.
Set hours & minutes
(*) Shaker jack
(*) Adaptor jack
Dimmer switch
1 - CONNECTING THE TELEPHONE
AC adaptor
1
PTT plug
(**) 230V
3
5
2
1 - Connect the PTT line cord.
2 - At your option you may connect your
telephone in the doubler plug.
4
Shaker
3 - Connect the PTT doubler plug in the wall
socket.
4 - Connect the adaptor line cord.
5 - Connect the adaptor in the wall socket. (**)
(**) Classified “hazardous voltage” according to EN60950 standard.
Electrical connection : The apparatus is designed to operate from a 230V 50Hz
supply only. (Classified as «hazardous voltage» according to EN60950 standard).
The apparatus does not incorporate an integral power on/off switch. To
disconnect the power, either switch off supply at the mains power socket or
4
unplug the AC adaptor. When installing the apparatus, ensure that the mains
power socket is readily accessible.
Telephone connection : Voltages present on the telecommunication network are
classified TNV-3 (Telecommunication Network Voltage) according to the
EN60950 standard.
2 - SETTING THE TIME ( )
- Press and hold (set clock) button.
- Press H (hour) and M (minute) until correct
hour and minutes appear on the display .
- Release (set clock) button.
- For p.m. hours, the p.m. indicator will appear
on the display near the inscription PM.
3 - SETTING THE ALARM TIME ( )
- Press and hold (set alarm) button.
- Press H (hour) or M (minute) until correct hour
and minutes appear on the display .
- Release (set alarm) button.
- Press , H and M to reset the alarm clock to
12.
5
4 - SETTING THE ALARM MODE
Put the function switch on A+T position.
Choose which alarm mode you wish to be
awakened to by moving the alarm mode switch
to one of the following selections :
V : only shaker activated
V+S : both sound and shaker alarm activated
S+F : both strobe light and sound alarm
activated
F+V : both strobe light and shaker alarm
activated
When the alarm is set to one of the alarm mo-
des, the alarm indicator will appear on the
display near the inscription AL.
The table below shows how the alarm modes
indicate an incoming call from the alarm clock.
ALARM MODE
SOUND
SHAKER
STROBE LIGHT
ACTION
Buzzer
Vibrates
Flashes
ALARM CLOCK
Continuous
Continuous
Continuous
INCOMING CALL
With pauses
With pauses
With pauses
6
5 - SNOOZE KEY ( )
When the alarm mode you have chosen is
switched on by the alarm time setting, pressing
the button will stop the alarm mode for
approximately 9 minutes. The alarm will then
switch the alarm mode on again for a further 9
minutes. This sequence can be carried out for
up to 2 hours after which the alarm mode will be
automatically switched off.
6 - SWITCHING THE ALARM OFF FOR 24H.
(OFF)
Press the alarm off button (OFF), the alarm will
then operate at the same time the next day . The
alarm if not switched off will continue to sound
for up to 2 hours and then be automatically
switched off.
7 - RINGER On/Off SWITCH ( A+T / OFF / T )
- A+T (alarm + telephone) : for the alarm and
telephone ring position.
- OFF : alarm and ring off.
- T (telephone) : for the telephone ring position.
7
Loading...