GE Digital IC755CxS06RDx, IC755CxW07CDx, IC755CxS10CDx, IC755CxS12CDx, IC755CxS15CDx Operating Manual

GFK-2847V

QuickPanel⁺ Operator

User

Dec 2016

IC755CxS06RDx (6” Display)
IC755CxW07CDx (7” Display)
IC755CxS10CDx (10" Display)
IC755CxS12CDx (12” Display)
IC755CxS15CDx (15” Display)

Manual

Interface

For public

disclosure

For public disclosure

These instructions do not purport to cover all details or variations in equipment, nor to provide for every
contingency

to be met during installation, operation, and maintenance. The information is supplied for informational

possible

purposes only, and GE makes no warranty as to the accuracy of the information included herein. Changes, modifications,
and/or improvements to equipment and specifications are made periodically and these changes may or may not be
reflected herein. It is understood that GE may make changes, modifications, or improvements to the equipment referenced
herein or to the document itself at any time. This document is intended for trained personnel familiar with the GE products
referenced herein.

GE may have patents or pending patent applications covering subject matter in this document. The furnishing of
this document does not provide any license whatsoever to any of these patents.

Public – This document is approved for public disclosure.

GE provides the following document and the information included therein as is and without warranty of any
kind, expressed or implied, including but not limited to any implied statutory warranty of merchantability or
fitness for particular purpose.

For further assistance or technical information, contact the nearest GE Sales or Service Office, or an authorized GE Sales
Representative.

Revised: Dec 2016
Issued: Nov 2013

© 2013 - 2016 General Electric Company.

* Indicates a trademark of General Electric Company and/or its subsidiaries.
All other trademarks are the property of their respective owners.

We would appreciate your feedback about our documentation.
Please send comments or suggestions to [e-mail]

GFK-2847V 3

For public disclosure

Document Updates

Location

Description

Updated ATEX Directive to 14/34/EU

Removed ATEX protection string - refer to the QP+ Operator Interface

Added the procedure for USB retaining clamps used in hazardous

Appendix A Product Certifications and Installation
Guidelines, Agency Approval

Conditions of Safe Use for Installation in Hazardous
Locations

Installation and Maintenance Requirements (IMR) (GFK-2981)

location installations for 7” Display units

Acronyms and Abbreviations

ARM Advanced RISC Machine
BBSRAM Battery-backed SRAM

DRAM Dynamic Random Access Memory

FG Frame Ground
FTP File Transfer Protocol
GND Ground
GUI Graphical user interface HTTP

HyperText Transfer Protocol

LCD Liquid Crystal Display

LED Light-emitting Diode

MIB Management Information Base (or Database)

OS Operating System

PME Proficy Machine Edition

RoHS Restrictions on Hazardous Substances
SELV Safety Extra Low Voltage

SNMP Simple Network Management Protocol

USB Universal Serial Bus
VESA Video Electronics Standards Association

4 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

Safety Symbol Legend

Warning

Caution

Attention

Indicates a procedure or condition that, if not strictly observed, could result
in personal injury or death.

Indicates a procedure or condition that, if not strictly observed, could result in
damage to or destruction of equipment.

Indicates a procedure or condition that should be strictly followed to improve
these applications.

GFK-2847V 5

For public disclosure

Contact Information

1-780-420-2010 (if toll free 800 option is unavailable)

GE Intelligent Platforms GmbH

+ 49-821–5034–0

If you purchased this product through an Authorized Channel Partner, then contact the seller directly.

Online technical support and GlobalCare

Additional information

Solution Provider

Technical Support

Contact us by telephone, email, or at http://support.ge-ip.com.

Online Technical Support

Phone

International Americas Direct Dial

Technical Support Email

Customer Care Email

Primary language of support

Online Technical Support

Phone

EMEA Direct Dial

Technical Support Email

Customer Care Email

Primary languages of support

Online Technical Support

Europe (not Germany), Middle East, and Africa (EMEA)

General Contact

http://support.ge-ip.com

http://www.ge-ip.com/

[e-mail]

http://support.ge-ip.com

1-800-433-2682

[e-mail]

[e-mail]

English

http://support.ge-ip.com

+ 800-1-433-2682

+ 420-23-901-5850 (if toll free 800 option is unavailable or dialing from a

mobile telephone)

[e-mail]

[e-mail]

English, French, Italian, Czech, Spanish

http://support.ge-ip.com

Information

Americas

Germany

Address

Phone

Fax

Technical Support Email

Online Technical Support

Phone

Technical Support Email

Customer Care Email

Memminger Str. 14

86159 Augsburg

Germany

+ 800–322–3616

+ 49–821–5034–119

[e-mail]

Asia Pacific

http://support.ge-ip.com

+ 86-400-820-8208

+ 86-21-3217-4826 (India, Indonesia, and Pakistan)

[e-mail] (China)

[e-mail] (Japan)

[e-mail] (remaining Asia customers)

[e-mail]

[e-mail]

(APO)

(China)

6 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

Notes

GFK-2847V 7

For public disclosure

Contents

1

1.1 Specifications

1.1.1 Physical Specifications and Mounting

Overview ..................................................................................................................................... 9

............................................................................................................................................ 10

1.1.2 Environmental

Specifications ........................................................................................................ 15

Options............................................................................. 10

2

2.1 Physical Characteristics

2.2 LED

3

3.1 Operating System

3.2 Backup

3.3 Storage Manager

3.4 Copy Project to SD

3.5 Proficy Machine Edition Project

3.6 FTP

3.6.1 Remote User Authentication

3.7 HTTP Server

3.8 SNTP

3.9 QuickPanel

3.9.1 Firmware Upgrade

3.10 Display Screen Sensitivity

3.11 Launch

3.12 VNC

3.13 Battery Life

3.14 Simple Network Management Protocol

Hardware.................................................................................................................................. 17

........................................................................................................................... 17

Indicators............................................................................................................................................ 23

2.2.1 Operation Status

2.2.2 Ethernet Port Operation LEDs

LEDs.................................................................................................................... 23

Software .................................................................................................................................... 25

..................................................................................................................................... 25

Utility............................................................................................................................................. 25

...................................................................................................................................... 25

Card ............................................................................................................................ 26

Update................................................................................................... 26

Server .................................................................................................................................................. 27

3.6.2 FTP with Removable Flash Devices

.............................................................................................................................................. 28

Server............................................................................................................................................... 28

+

OS Utilities Settings Tool

......................................................................................................................... 30

3.9.2 Firmware Upgrade for Specific Build

3.9.3 Bypass Startup

3.9.4 Reset Enhanced Security

3.9.5 Enable or Disable

Application .................................................................................................................................. 39

Server ............................................................................................................................................... 40

Prediction............................................................................................................................. 41

3.14.1 Configure Trap

3.14.2 Enable or Disable

3.14.3 Export MIB to SD

3.14.4 Load MIB into SNMP

3.14.5 Data Types Mapping between PME Project and SNMP

3.14.6 Establish SNMP

3.15 Screensaver…………..

Programs ............................................................................................................... 33

................................................................................................................ 35

SNMP

Agent

Tool ................................................................................................................ 38

Destinations........................................................................................................ 49

SNMP

Agent

Card.................................................................................................................. 50

Manager .................................................................................................... 51

Communication ................................................................................................. 52

................................................................................................................................ 53

....................................................................................................... 23

......................................................................................................... 27

.............................................................................................. 27

..................................................................................................... 29

Version................................................................................ 32

....................................................................................................... 36

(SNMP) .................................................................................... 45

.................................................................................................... 50

............................................................. 52

4 Pre-installation

Checks........................................................................................................ 55

4.1 Unpacking and Inspection

4.2 Basic Setup

4.3 Initial

4.3.1 Connecting Input

4.3.2 Initial

............................................................................................................................................ 57

Startup ......................................................................................................................................... 58

Configuration ............................................................................................................ 59

................................................................................................................... 55

Power ..................................................................................................... 58

8 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

4.4 Runtime Setup

4.5 Firmware

4.6

Shutdown .............................................................................................................................................. 60

...................................................................................................................................... 59

Updates................................................................................................................................. 60

5 Mounting and

5.1 Protective Sheet

5.2 Mounting Location

5.3 Panel

5.4 Mounting and Installation Procedure

5.5 VESA Arm

5.6 Battery Installation and

5.6.1

5.6.2

5.6.3

5.7

5.7.1 Power Connector Pin-out for IC755CxS06RDx, IC755CxW07CDx, and

5.7.2 Ethernet for IC755CxS06RDx, IC755CxW07CDx, and IC755CxSxxCDx

5.7.3 Serial Port Details

5.7.4 Universal Serial Bus (USB)

5.7.5 Audio (LINE OUT) Details for IC755CxS06RDx, IC755CxW07CDx, and

5.7.6 Audio (MIC IN) Details (Only Applicable to IC755CxS06RDx and

5.7.7 SD Card Slot and Storage

6

6.1 Touchscreen Display

6.2 Keyboard

6.2.1 External Keyboard

6.2.2 Soft Input

6.3 Mouse

6.4

6.5 Memory

6.5.1 DRAM Memory

6.5.2 Memory Allocation

Mounting ......................................................................................................................................... 63

Mounting.................................................................................................................................. 68

IC755CxS06RDx ............................................................................................................................... 70

IC755CxW07CDx............................................................................................................................. 72

IC755CxSxxCDx ............................................................................................................................... 74

Connectors ............................................................................................................................................... 76

Operation ...................................................................................................................................... 89

6.1.1 Display Brightness

6.1.2 Display Backlight

6.1.3 Touchscreen

Configuration............................................................................................................................ 92

........................................................................................................................................................ 92

Printing....................................................................................................................................................... 93

..................................................................................................................................................... 94

7 Secomea Security

7.1 Secomea Configuration

7.2 Secomea

Products .................................................................................................................................... 98

Installation...................................................................................................... 61

Installation .................................................................................................................... 61

................................................................................................................................... 62

..................................................................................................... 66

Replacement .................................................................................................... 69

........................................................................................................................... 78

Ports ..................................................................................................... 84

IC755CxW07CDx).................... 85

............................................................................................................... 86

................................................................................................................................ 89

Adjustment ............................................................................................... 89

Configuration .............................................................................................. 90

Re-calibration ..................................................................................................... 91

(Optional).................................................................................................... 92

Panel ......................................................................................................................... 92

..................................................................................................................... 94

Modification .............................................................................................. 95

(Optional).................................................................................................... 97

Tool .................................................................................................................... 97

IC755CxSxxCDx ........... 76

...................................... 76

IC755CxSxxCDx ............. 85

Appendix A Product Certifications and Installation
Appendix B Orderable Part
Appendix C IC755CxS10CDx, IC755CxS12CDA, and IC755CxS15CDx Serial Port

Details .......................................................................................................................................................

Guidelines.........................................

Numbers .............................................................................................

101

107

109

Overview

For public disclosure

GFK-2847V 9

1 Overview

Note This manual specifically describes the QuickPanel+ IC755CxS06RDx, IC755CxWxxCDx and IC755CxSxxCDx

display units.

The QuickPanel
based on an Advanced RISC Machine (ARM) core micro-processor to combine a high-resolution touchscreen operator
interface with a variety of communications options. Users can connect to most industrial equipment using the
QuickPanel

The QuickPanel+ is equipped with several memory types to satisfy the most demanding applications. A section of
Dynamic Random Access Memory (DRAM) is split between the operating system, an object store, and application
memory. Additionally, a section of Non-volatile Random Access Flash Memory (NOVRAM), functioning as a virtual hard
drive, is divided between the operating system and persistent storage for application programs. Retentive memory is a
battery-backed Static Random Access Memory (SRAM) to store and protect data during a power failure.

+

Operator Interface is an all-in-one micro-computer designed for maximum flexibility. The design is

+

communications ports.

QuickPanel+ Operator Interface

Display

10 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

1.1 Specifications

Item

Specification

Freescale i.MX535 (1 GHz ARM Cortex A8)

RAM

DDR3 SDRAM 512 MB

ROM

NAND FLASH 256 MB

512 KB (with battery backup)

Operating System

Microsoft Windows Embedded Compact 7

Type

5.7” TFT LCD

320(W) x 240(H) pixels QVGA

65,536

Brightness

Backlight

Touch Panel Type

Analog Resistive

Single-touch

Ethernet Port

1x10Base-T / 100Base-TX

1x RS-232C (COM1) (5-pin connector)

2x USB 2.0 (Type-A) maximum power (5 V at 0.5 A)

USB, Device

1x USB 2.0 (mini Type-B)

Storage

1x Mic In (Mono) (3.5 mm jack),
Noise Voltage

1500 V p-p

1µs

Rise Time

1ns

Rated Voltage

24 V dc ±20% (3-pin connector)

Power Consumption

Frame Ground (FG)

Frame Ground (GND) is connected internally to Signal GND

Dimensions (L×W×D)

192 × 137 × 36 mm (7.56 × 5.39 × 1.42 in)

Weight

0.7 Kg (1.54 lb)

183.50 × 128.50 mm (7.22 × 5.06 in)

75 x 75 mm (2.95 x 2.95 in)

1.1.1 Physical Specifications and Mounting Options

1.1.1.1 IC755CxS06RDx Specifications

Processor

Memory

SRAM

Resolution

Display

Color

375 cd/m

LED

2

Touchscreen

Communications

Audio

Noise Immunity

Input power

Mounting Options

Multi-touch

Serial Port
USB, Host

1x SD/SDHC card slot

1x Line Out (Stereo) (3.5 mm jack)

Pulse Duration

15 W maximum

Panel Cutout Dimensions
VESA Mount

Overview

For public disclosure

GFK-2847V 11

1.1.1.2 IC755CxW07CDx Specifications

Item Specification

Processor

Freescale i.MX535 (1 GHz ARM Cortex A8)

RAM

DDR2 SDRAM 512 MB

ROM

SLC NAND 256 MB

SRAM

512 KB (with battery backup)

Operating System

Microsoft Windows Embedded Compact 7

Type

7" Widescreen TFT LCD

Resolution

800(W) x 480(H) pixels WVGA

Color

65,536

Brightness

310 cd/m

Backlight

LED

Touch Panel Type

Projected capacitive

Multi-touch

Two-point

Ethernet Port

1x 10/100Base-T (RJ-45)

Serial Port

1x RS-232 UART port (5-pin connector)

USB, Host

2x USB 2.0 (Type-A) maximum power (5 V at 0.5 A)

USB, Device

1x USB 2.0 (mini Type-B)

Storage

1x SD/SDHC card slot

1x Mic In (Mono) (3.5 mm jack)
Noise voltage

1500 V p-p

Pulse duration

1µs

Rise time

1ns

Rated Voltage

24 V dc ±20% (3-pin connector)

Power Consumption

15 W maximum, 0.625 A

Frame Ground (FG)

Frame GND is connected internally to Signal GND

Dimensions (L×W×D)

192 × 137 × 36 mm (7.56 × 5.39 × 1.42 in)

Weight

0.80 kg (1.76 lbs)

183.50 × 128.50 mm (7.22 × 5.06 in)

75 x 75 mm (2.95 x 2.95 in)

Memory

Display

Touchscreen

Communications

2

Audio

Noise Immunity

Input power

Mounting Options

1x Line Out (Stereo) (3.5 mm jack)

Panel Cutout Dimensions

VESA Mount

12 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

1.1.1.3 IC755CxS10CDx Specifications

Item Specification

Processor

Freescale i.MX535 (1 GHz ARM Cortex A8)

RAM

DDR3 SDRAM 1 GB

ROM

SLC NAND 512 MB

SRAM

512 KB (with battery backup)

Operating System

Microsoft Windows Embedded Compact 7

Type

10.5" Standard TFT LCD

Resolution

800(W) x 600(H) pixels SVGA

Color

65,536

Brightness

400 cd/m

Backlight

LED

Touch Panel Type

Projected capacitive

Multi-touch

Two-point

2x 10/100Base-T (RJ-45)

1x RS-232 UART port
USB, Host

2x USB 2.0 (Type-A) maximum power (5 V at 0.5 A)

USB, Device

1x USB 2.0 (mini Type-B)

Storage

1x SD/SDHC card slot

1x Line Out (Stereo) (3.5 mm jack)

Noise voltage

1500 V p-p

Pulse duration

1µs

Rise time

1ns

Rated Voltage

12/24 V dc ±20% (3-pin connector)

Power Consumption

Frame Ground (FG)

Frame GND is connected internally to Signal GND

Dimensions (L×W×D)

278 × 222 × 65 mm (10.95 × 8.74 × 2.56 in)

Weight

2.40 kg (5.29 lbs)

266 × 210 mm (10.47 × 8.27 in)

100 x 100 mm (3.94 x 3.94 in)

Memory

Display

Touchscreen

Ethernet Port

2

Communications

Audio

Noise Immunity

Input power

Mounting Options

Serial Port

Panel Cutout Dimensions

VESA Mount

1x RS-232/485 port (2x 5-pin connector)

18 W maximum 1.5 / 0.75 A

Overview

For public disclosure

GFK-2847V 13

1.1.1.4 IC755CxS12CDx Specifications

Item Specification

Processor

Freescale i.MX535 (1 GHz ARM Cortex A8)

RAM

DDR3 SDRAM 1 GB

ROM

SLC NAND 512 MB

SRAM

512 KB (with battery backup)

Operating System

Microsoft Windows Embedded Compact 7

Type

12.1" Standard TFT LCD

Resolution

800(W) x 600(H) pixels SVGA

Color

65,536

Brightness

450 cd/m

Backlight

LED

Touch Panel Type

Projected capacitive

Multi-touch

Two-point

2x 10/100Base-T (RJ-45)

1x RS-232 UART port

USB, Host

2x USB 2.0 (Type-A) max power (5 V at 0.5 A)

USB, Device

1x USB 2.0 (mini Type-B)

Storage

1x SD/SDHC card slot

1x Line Out (Stereo) (3.5 mm jack)

Noise voltage

1500 V p-p

Pulse duration

1µs

Rise time

1ns

Rated Voltage

12/24 V dc ±20% (3-pin connector)

Power Consumption

30 W maximum, 2.5 / 1.25 A

Frame Ground (FG)

Frame GND is connected internally to Signal GND

Dimensions (L×W×D)

314 × 248 × 65 mm (12.36 × 9.76 × 2.56 in)

Weight

3 kg (6.61 lbs)

Panel Cutout Dimensions

302 × 228 mm (11.89 × 8.98 in)

VESA Mount

100 x 100 mm (3.94 x 3.94 in)

Memory

Display

Touchscreen

2

Communications

Audio

Noise Immunity

Input power

Mounting Options

Ethernet Port

Serial Port

1x 10/100Base-T (RJ-45) for IC755CxS12CDA

1x RS-232/485 port (2x 5-pin connector) (1x
10-pin connector for IC755CxS12CDA)

14 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

1.1.1.5 IC755CxS15CDx Specifications

Item Specification

Processor

Freescale i.MX535 (1 GHz ARM Cortex A8)

RAM

DDR3 SDRAM 1 GB

ROM

SLC NAND 512 MB

SRAM

512 KB (with battery backup)

Operating System

Microsoft Windows Embedded Compact 7

Type

15" Standard TFT LCD

Resolution

1024(W) x 768(H) pixels XGA

Color

65,536

Brightness

310 cd/m

Backlight

LED

Touch Panel Type

Projected capacitive

Multi-touch

Two-point

2x 10/100Base-T (RJ-45)

1x RS-232 UART port
USB, Host

2x USB 2.0 (Type-A) maximum power (5 V at 0.5 A)

USB, Device

1x USB 2.0 (mini Type-B)

Storage

1x SD/SDHC card slot

1x Line Out (Stereo) (3.5 mm jack)

Noise voltage

1500 V p-p

Pulse duration

1µs

Rise time

1ns

Rated Voltage

12/24 V dc ±20% (3-pin connector)

Power Consumption

30 W maximum, 2.5 / 1.25 A

Frame Ground (FG)

Frame GND is connected internally to Signal GND

Dimensions (L×W×D)

399 × 323 × 70 mm (15.71 × 12.72 × 2.76 in)

Weight

4.46 kg (9.83 lbs)

Panel Cutout Dimensions

379 × 305 mm (14.92 × 12.01 in)

VESA Mount

100 x 100 mm (3.94 x 3.94 in)

Memory

Display

Touchscreen

Ethernet Port

2

Communications

Audio

Noise Immunity

Input power

Mounting Options

Serial Port

1x RS-232/485 port (2x 5-pin connector)

Overview

For public disclosure

GFK-2847V 15

1.1.2 Environmental Specifications

Item

IC755CxS06RDx

IC755CxW07CDx

IC755CxS10CDx

IC755CxS12CDx

IC755CxS15CDx

Cooling

Ambient

Ambient

Ambient

Pollution Degree 2, Indoor use

only

5 to 9 Hz single-amplitude 3.5 mm; 9 to 150 Hz

constant-accelerated

velocity 9.8 m/s2; X, Y,

800~1114 hPa, altitude up to 2000 m (6561.68 ft)

Compliant with EU RoHS Directive 2011/65/EU

Enclosure

Note Install the QuickPanel

+

in a well-ventilated location that is not exposed to dust, corrosive gases or liquids, rain,

strong ultra-violet light or direct sunlight, and meets the following specifications.

Natural

convection

Operating
Temperature

Storage
Temperature

Humidity
(Operating
and Storage)

Environment
Vibration

Resistance
Altitude

RoHS

Rating

0 to 55°C (32 to 131

-10 to 60°C (14 to 140

85% RH Non-condensing, wet-bulb temperature: 30°C (86 °F) or less

Z directions 10 time (100 minutes) (Compliance 3502, IEC61131-2 JIS B)

UL

Type 4X rating; IP65 in panel mount only

°F)

°F)

Note For additional product standards and agency approvals, refer to Appendix A.

16 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

Notes

Hardware

For public disclosure

GFK-2847V 17

2 Hardware

This chapter describes the QuickPanel+ hardware features, including physical characteristics and LED
indicators.

2.1 Physical Characteristics

In addition to the primary touchscreen interface, the QuickPanel+ Operator Interface supports a variety of
communication ports. The following diagrams illustrate the physical layout of the QuickPanel
including locations of status LEDs, communications ports, and connectors.

+

Operator Interface,

18 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

144.7 (5.70 in)

1

)

75 (2.95 in)

137 (5.39 in) x 2

192 (7.56 in) x 2

36 (1.42 in) x 2

115.2

(4.5 in)

SD Card

LCD Active Area

115.2 x 86.4
(4.5 x 3.4 in)

USB Device

LINE OUT

MIC IN

Input Power

LAN

USB Host Ports

183.50 (7.22 in)
75 (2.95 in)

Serial Interface

Battery Cover

28.50 (5.06 in

Effective Screw Depth 6 mm (0.24 in)

IC755CxS06RDx Hardware

License Label

Product Nameplate

Features

Hardware

For public disclosure

GFK-2847V 19

Indicator LED

Touchscreen

LCD

I

nput

Power

LAN

USB Host

Por

t

s

COM

IC755CxW07CDx Hardware

Features

Note Refer to the section IC755CxW07CDx Specifications for drawing dimensions.

tat

us

S

Battery
Cover

SD Card

MICRO USB

LINE OUT

I

N

MIC

20 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

SD Card

T

ouchscreen

LCD

A

LAN2

U
Hos
P

orts

SB

t

N1

L

IC755CxS10CDx Hardware

Note Refer to the section IC755CxS10CDx Specifications for drawing dimensions.

MICRO C

U

SB

O

M2

O

M1 LIN

C

O

UT

Features

Stat

us

E

Indicator L

I

nput

E

P

ower

D

Hardware

For public disclosure

GFK-2847V 21

!

!

IC755CxS12CDx Hardware

Features

Note Refer to the section IC755CxS12CDx Specifications for drawing dimensions.

22 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

SD Card

T

ouchscreen

LCD

I

Stat

us

ndicator

E

D

L

LAN2

LAN1

USB

MICRO C

Hos

t

SB

U

Port

s

O

M2

COM1

L

INE
OUT

I

nput

P

ower

Note Refer to the section IC755CxS15CDx Specifications for drawing dimensions.

IC755CxS15CDx Hardware

Features

Hardware

For public disclosure

GFK-2847V 23

2.2 LED Indicators

LED State

QuickPanel+ State

Amber, solid

Operating system starting

Normal operating state

Green, blinking

Backlight off

Red, blinking

Backlight failure

Off

Power not applied to unit

Operating State

Speed

Yellow, on

The QuickPanel+ Operator Interface provides LED indication for the following:

• Operation status

• Ethernet Port operation

2.2.1 Operation Status LEDs

The QuickPanel+ has one tri-color LED that provides visual operation status indication for
IC755CxS06RDx, IC755CxW07CDx, the and IC755CxSxxCDx units.

Green, solid

2.2.2 Ethernet Port Operation LEDs

The Ethernet port has two LED indicators: Speed and Link Activity.

Speed Link Activity

LED

LED State

10/100

Link Activity

Green, on

Link status

24 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

Notes

Software

For public disclosure

GFK-2847V 25

3 Software

This chapter provides QuickPanel+ software information and procedures to perform the most common tasks.

3.1 Operating System

Note Refer to http://windows.microsoft.com.

The QuickPanel
user interface (GUI). It is stored in flash memory and copied to a block of DRAM for execution. The OS automatically
starts following QuickPanel

3.2 Backup Utility

+

operating system (OS), Microsoft Windows Embedded Compact 7, is a full 32-bit OS with graphical

+

unit powerup or reset.

Attention

The QuickPanel
Registry or Desktop to Flash Memory. The Backup Utility achieves the following:

• Stores the Windows Embedded Compact 7 registry (including any control panel settings) in Flash memory

• Stores changes (or additions) made to the \Windows sub-tree of the file system in the user block of flash memory

+

is not battery powered; therefore, a Backup Utility feature saves the changes made to the Windows

Run the Backup Utility after configuration changes to the operating system
or installing applications, and before shutdown.

3.3 Storage Manager

Note Storage Manager is accessed from the Control Panel folder. Online help is available.

Use Microsoft Storage Manager to repair or format lost or corrupted data volumes existing in the SD Card, battery-backed
SRAM (BBSRAM), or USB Flash Keys (thumb drives).

Note Data volumes existing in the main flash file system of the QuickPanel

+

may not be repaired by Storage Manager.

26 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

3.4 Copy Project to SD Card

The custom utility Copy Project to SD Card transfers Proficy Machine Edition View and Control projects between compatible
QuickPanel

+

units using SD cards.

Caution

➢ To copy a Proficy Machine Edition project to an SD card

1. Verify that there is a blank SD card in the SD card port.

2. Double tap the Copy Project to SD Card icon on the desktop.

3. If the project is secured with an enhanced security password, then the password authentication window will be

displayed. The user shall be able to proceed only when the password is successfully authenticated.

4. From the Copy Project Query confirmation window, tap Yes.

Caution

Before disconnecting power, verify that the copy or update operation is complete
(no busy message or wait cursor).

Copying a project while Proficy Machine Edition runtimes are active may cause an
incomplete copy to be created if the runtimes are also writing to files in the project
folders. If the utility detects this situation, it will notify you to stop the runtimes
before making the backup. You will not be able to create a backup while the
runtimes are writing files.

3.5 Proficy Machine Edition Project Update

Update a Proficy Machine Edition (PME) application that is currently stored on the QuickPanel+ unit with a revision stored
on a

flash device, such as an SD card.

➢ To update a Machine Edition project

1. Insert the flash device containing an upgraded version of the Proficy Machine Edition project into the appropriate port.

2. Restart the unit.

Note Depending on set options, the update may or may not be enabled, or may update automatically. If there is
more than one flash device with a valid project copy present, a Select Media confirmation window displays,
prompting you to choose with which flash device to update Select the device from the list and click OK to continue.
When a valid project
is found on the flash device, you will be prompted to install the project or skip it. Tap OK to install or Cancel to skip
the installation, and continue to restart. If an invalid project is found, an error message displays. This window must
be closed
before the unit will restart.

3. Remove the flash device from the port.

Software

For public disclosure

GFK-2847V 27

3.6 FTP Server

The File Transfer Protocol (FTP) server included with the QuickPanel+ unit supports standard (RFC 959). It does not
support Secure File Transfer Protocol (SFTP) or implicit FTPS, which uses different ports and is based on Secure Shell
(SSH) rather than Secure Sockets Layer (SSL).

The FTP server is configured with the Quick Panel+ Setup Tool. By default, the server is not enabled. Once enabled, a
background program will run, waiting for clients to connect. Up to ten connections are supported. Sessions that are
idle for five minutes are terminated by the server.

The server supports non-secure operation. All information including username, password, and data is transmitted
with no encryption and is susceptible to packet sniffing and various FTP attacks.

Note If the server status is changed, the QuickPanel

+

must be restarted before changes take effect.

3.6.1 Remote User Authentication

Note The FTP root directory is available from the QuickPanel

+

as \, and is the root of the flash device.

The server only supports anonymous login with password requested (but not validated). This may prevent some
types of attacks and is required by some clients. Once connected, the remote user is logged into the FTP root
directory.

3.6.2 FTP with Removable Flash Devices

All removable flash devices remote-FTP users as directories off the FTP root directory. Computer Flash card
partitions display as directories such as \SDMemory and USB Flash Keys display as directories such as \Hard Disk.
Full access privileges are granted for the client in these folders/devices.

Removable flash device directories are captured when a session is opened and are not changed while the session exists.
If you start without an installed SD Card, close your session and log on again to view the SD Card directory. If the SD Card
existed when you logged on, and is removed and inserted, it will still work, provided the SD Card’s device name did not
change during

reinsertion.

28 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

3.7 HTTP Server

The HyperText Transfer Protocol (HTTP) server included with the QuickPanel+ supports standard (RFC 2616). The HTTP
server is configured with the Quick Panel+ Setup Tool. By default, the server is not enabled. Once enabled, a background
program will run, waiting for clients to connect. From the QuickPanel

+

Operator Interface, the default web page is
located in
\Windows\www\wwwpub.

The server supports non-secure port 80 operation.

Note If the server status is changed, the QuickPanel

+

must be restarted before changes take effect.

3.8 SNTP Server

The SNTP server included with the QuickPanel+ supports SNTP Version 4 for IPv4, IPv6 and OSI. The SNTP server is
configured with the Quick Panel+ Setup Tool. By default, the server is not enabled. Once enabled, the server will refresh
the time specified in the setup tool configuration. Pressing the Update Now button immediately obtains the time from
the configured time server.

The SNTP server supports non-secure UDP port 123 operation.

Software

For public disclosure

GFK-2847V 29

3.9 QuickPanel+ OS Utilities Settings Tool

QuickPanel+ Product

Firmware Build

IC755CxS06RDx (6" Display)

01 (initial

release)

IC755CxW07CDx (7” Display)

IC755CxS10CDx (10” Display)

IC755CxS15CDx (15” Display)

Note DIP switches are set in the OFF position (default) in the factory.

The QuickPanel

+

Operator Interface is equipped with DIP switches to perform control functionality, as follows:

• DIP Switch 1 (SW2 Switch) enables firmware upgrade. Firmware upgrade is allowed only after turning this switch
in the ON position. It is highly recommended to turn the switch position to OFF after firmware upgrade is
completed as a security measurement.

• DIP Switch 2 (SW2 Switch) controls Force Startup. Turning this switch to the ON position forces the
startup applications to run when the operating system is started.

Note The DIP Switch feature is designed as a security measurement. However, security requirements can also be met
using the gesture-based feature.Prior to the listed firmware builds, these operations were only supported using the DIP
Switch
settings.

Some operators find it difficult to use the DIP Switch settings to perform these functions (such as removing the back
plate of the device and adjusting the positions of DIP Switch for each operation). As an alternative to using the DIP
Switch settings, the QuickPanel

+

OS Utilities Settings tool contains finger gesture-based utilities to perform the same

operations. This functionality is available with the firmware builds listed in the following table.

QuickPanel+ OS Utilities Settings Tool Support

21

IC755CxS12CDx (12” Display)

12

The tool operation buttons for each utility only respond to a double-tap finger gesture. It will not accept any keyboard or
mouse clicks, finger simulator-based inputs, or click inputs from any remote touch-based device. The user can access
the tool from the Start menu by selecting Programs, System, and QuickPanel

+

OS Utilities Settings on the device. The

tool can be used to perform the following operations using the double-tap feature, without adjusting the DIP Switch
positions:

• Firmware Upgrade

• Bypass Startup Programs

• Reset Enhanced Security

• Enable/Disable

SNMP

Agent

For security, only permit these operations when the operator is physically located
near the QuickPanel

+

and require that users perform a physical action on the device.

Attention

30 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

3.9.1 Firmware Upgrade

Note This utility operates similar to the QuickPanel

The operator can continue to use the QuickPanel

+

Update Tool, which comes with the OS image upgrade binaries.

+

Update Tool to use the DIP Switch feature.

The Firmware Upgrade utility setting enables operators to upgrade the firmware. Firmware updates are not supported
over

Ethernet or Serial interfaces. Insert the media (SD Card) containing the required files for firmware upgrade and perform
the following procedure.

Note Make sure the copy of required binaries to the SD card is not within a folder.

Note The firmware package contains encrypted .nbo files. Use the PreUpdate.exe tool to decrypt the .nbo files before

using them for upgrade.

After a firmware upgrade, which refreshes the device fresh, the user must download the project again and install
their own tools (including third party tools) on the device.

Note It is recommended that the user back up any important data prior to firmware upgrade so that they can replace
the data after firmware upgrade if necessary.

If the current firmware build version on the QuickPanel+ is any of the following, refer
to the section Firmware Upgrade for Specific Build Version:

• Build 3 or below for IC755CxS06RDx

(6” Display)

• Build 23 or below for IC755CxW07CDx

Attention

(7” Display)

• Build 14 or below for

IC755CxS10CDx

(10" Display), IC755CxS12CDx

(12” Display), and IC755CxS15CDx

(15” Display)

Software

For public disclosure

GFK-2847V 31

➢ To perform a firmware upgrade

1. From the Start menu, select Programs, System, and QuickPanel+ OS Utilities Settings Tool to display the

QuickPanel

2. Upgrade the firmware.

+

OS Utilities Settings window.

From the QuickPanel + OS Utilities
Settings window , select Firmware

Upgrade, then double- tap Upgrade.

3. The operator interface guides the operator through the firmware upgrade process. After successful upgrade,

restart the device.

4. Download the project and install any site-specific tools, including third party tools, on the device.

32 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

3.9.2 Firmware Upgrade for Specific Build Version

The following procedure is applicable to the following QuickPanel+ display units:

• QuickPanel+ IC755CxS06RDx (6” Display) with build 3 or below

+

• QuickPanel

• QuickPanel
14 or below

➢ To perform a firmware upgrade for a specific firmware build version

1. Put the files in the firmware package on the SD Card.

2. Double-click QPPlusUpdate.exe and run the program.

3. Perform the firmware upgrade.

Attention

IC755CxW07CDx (7” Display) with build 23 or below

+

IC755CxS10CDx (10" Display), IC755CxS12CDx (12” Display), and IC755CxS15CDx (15” Display) with build

From the QuickPanel+ Update Tool dialog box, click Upgrad e.

For a QuickPanel+ 7” inch Display unit, the following message displays during the
process of firmware upgrade. You must re-run the QPPlusUpdate.exe program after
reboot, which means you will run the QPPlusUpdate.exe program a total of two
times to complete the upgrade process.

QuickPanel+ 7” inch Display Reboot and Run Program Message

Software

For public disclosure

GFK-2847V 33

3.9.3 Bypass Startup Programs

Note This utility functions the same as disabling or enabling the Don’t startup Program functionality using DIP Switch

Position 2.

The Bypass Startup Programs utility enables the operator to choose the gesture-based feature or DIP Switch (Use DIP
Switch)

feature to perform the Force Startup operation.

➢ To bypass startup programs and force startup

1. From the Start menu, select Programs, System, and QuickPanel+ OS Utilities Settings Tool to display the

QuickPanel

2. Enable or disable the bypass startup programs feature.

+

OS Utilities Settings window.

From the QuickPanel
window , select Bypass Startup

+

OS Utilities

Settings

Prog rams.

To use th e DIP Switch feature to perform
operation , select Use DIP

Switch.

To use the double-tap feature to
this operation , double -tap

Enab le.

this

perform

34 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

If Enable is double- tapped, the startup
window displays and all startup

.

programs are enabled to run

If Disab le is double- tapped, the startup
window displays . Click Don’t run Startup
programs to stop all s

.

from running

If Use DIP Switch is selected, Don’t run StartUp Programs displays on the startup window based on the position of
DIP Switch 2.

tart

up programs

Software

For public disclosure

GFK-2847V 35

3.9.4 Reset Enhanced Security

The QuickPanel+ Operator Interface is configured using the Proficy Machine Edition (PME) application. Using the PME
Enhanced Security feature, users can specify password protection for any network-connected QuickPanel
perform certain operations, such as the download operation. Every operation to connect to the device requires a
password.

If you forget or do not know your password, the Reset Enhanced Security feature enables a QuickPanel
configuration download on the device by permitting the user to disable the Enhanced Security feature using the
double-tap feature.

Note Prior to support of the QuickPanel

+

OS Utilities Settings Tool, if the user forgot or did not know their password,

the only resolution was to contact Technical Support to reset the password or upgrade the firmware on the device.

➢ To disable Enhanced Security

1. From the Start menu, select Programs, System, and QuickPanel+ OS Utilities Settings Tool to display the

QuickPanel

2. Disable the Enhanced Security setting.

+

OS Utilities Settings window.

From the QuickPanel + OS Utilities
Settings window , select Reset
Enhanced Security, then double ­tap Disable.

+

+

device to

36 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

3.9.5 Enable or Disable

SNMP

Agent

The QuickPanel+ Operator Interface can be enabled as a Simple Network Management Protocol (SNMP) Agent with
the capability to communicate with SNMP Managers for notification of Traps and responding to Query HMI Tag
values.

Since it is designed to run over a public network, SNMP communication is disabled by default on the QuickPanel+ device
for security reasons. As a security measure, the SNMP feature requires a tactile input gesture to enable and disable
SNMP
communication.

Note Refer to the section Simple Network Management Protocol (SNMP) for further details.

Note Enabling or disabling SNMP communication is a one-time user configuration.

➢ To enable the

SNMP

Agent

1. From the Start menu, select Programs, System, and QuickPanel+ OS Utilities Settings Tool to display the

QuickPanel

2. Enable SNMP communication.

+

OS Utilities Settings window.

From the QuickPanel+ OS Utilities
Settings window, select SNMP.

Double-tap Enabl e to enable
SNMP communication .

Attention

SNMP communication is enabled on the device only when the user acknowledges
this security dialog box and clicks Yes.

Click Yes to acknowledge the security
risk and enable SNMP

communication

.

Software

For public disclosure

GFK-2847V 37

Note Any failure or errors while enabling or disabling the SNMP service would be communicated to the user
through a dialog box.

➢ To disable the

1. From the Start menu, select Programs, System, and QuickPanel+ OS Utilities Settings Tool to display the

QuickPanel

2. Disable SNMP communication.

SNMP

Agent

+

OS Utilities Settings window.

From the QuickPanel+ OS Utilities
Settings window, select SNMP.

Double-tap Disable to disable
SNMP communication .

38 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

3.10 Display Screen Sensitivity Tool

The QuickPanel+ 7”, 10”, 12”, and 15” display units use capacitive screen technology that is far more responsive than the
previously used resistive touchscreen technology. Resistive screens required the operator to firmly press down on the
resistive overlay for a response. Capacitive screens rely on the capacitive properties of the operators finger pressing
lightly on the screen.

If the operator is wearing gloves, this can affect the operation of the capacitive screens. The thickness of the glove
keeps the operator’s finger slightly further from the screen. To accommodate gloved operation, the Sensitivity Tool
allows the screen sensitivity to be set to a higher level. Setting the screen sensitivity to High enables the QuickPanel
display screen to operate with the user wearing most types of work gloves. For thicker gloves, the user may need to
press down more firmly to place
the finger closer to the screen, which causes the finger pad to spread out slightly to make a larger capacitive area.

Note Gloved operation works best when the operator is wearing gloves that fit. If the fingers do not extend to the end
of the glove, the empty space at the fingertip may make it difficult to operate the display screen while wearing gloves.

Setting the screen sensitivity to Low enables the QuickPanel

+

operator actions to be slow and deliberate as they were

using resistive screens. With low sensitivity, the operator must press firmly down on the display screen for a response.

➢ To modify the Sensitivity Tool

1. From the Start menu, select Programs, System, and Sensitivity Tool to display the Sensitivity Setting window.

2. Set the sensitivity level.

Select the sensitivity
level and press OK.

+

Software

For public disclosure

GFK-2847V 39

3.11 Launch Application

The Launch application window contains the shortcuts to launch some of the major QuickPanel+ Operator
Interface applications.

➢ To launch an application

From the Start menu , select

Programs, System , and
Launch Appli catio n.

From the Launch Application
window, tap an applicatio n icon
to start the application.

If the application is not listed, select
… to browse f or and select an
application, then click to
open (start) the application.

40 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

3.12 VNC Server

The VNC Server enables remote, visual connectivity to the QuickPanel+ Operator Interface from a laptop computer or a
mobile device through the remote VNC Viewers. User authentication of the VNC Server in the QuickPanel
by the configuration of the Enhanced Security feature on the device. If the Enhanced Security feature is enabled for the
device, a VNC Viewer can connect to the QuickPanel

+

on the VNC Server. Connection is dependent upon user
authentication with the correct password. User password entry is validated with the Enhanced Security password. If the
Enhanced Security feature is disabled for the device, the VNC Server does not enforce authentication of VNC Viewers.

The VNC Server is automatically launched during QuickPanel+ startup. It can also be launched manually from the Launch
Application.

➢ To manually launch the VNC Server: from the Start menu, select Programs, System, Launch Application

and start the VNC Server application.

From the Launch Application
window , tap the QP

Server application

Note The VNC server starts approximately 40 sec after the QuickPanel

+

startup process has completed.

+

is determined

+

VNC

icon

.

Software

For public disclosure

GFK-2847V 41

3.13 Battery Life Prediction

The QuickPanel+ Operator Interface provides an estimated lifespan of the battery in the device. To display the battery
life prediction, the current time on the QuickPanel

+

device must be set. If a battery is not present, the QuickPanel

BatteryStatus tab cannot provide battery life prediction.

➢ To display the battery life prediction: from the Start menu, select System, open the QuickPanel+ Setup tool, and

select the BatteryStatus tab.

+

Battery Life Prediction

Example

Note If the current time is not set on the device, the QuickPanel+ Setup Tool dialog box will not be capable of provide

an accurate battery life prediction.

➢ To set the current time to display battery life prediction

1. If the current time is not set on the device, the QuickPanel+ Setup Tool displays the following message stating that

the current date and time must be set on the device to display the correct battery life prediction.

Click OK and set the current date and time on the device.

Current Time Not Set

Message

42 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

2. After setting the current time, open the QuickPanel+ Setup Tool, and select the BatteryStatus tab to display the

correct battery life prediction information.

Example of Battery Life Prediction Displayed After Current Time

Set

3. If the battery was replaced or removed on the QuickPanel+, QuickPanel+ Setup Tool BatteryStatus displays

two possible scenarios related to the battery.
(The battery life prediction is estimated based on this selection.)

Battery Status

Options

Software

For public disclosure

GFK-2847V 43

4. If the option The battery is not present is selected, a message displays stating that battery life cannot be
predicted without a battery installed on the device.

Battery is Not Present

Message

5. If the option The battery was replaced is selected, enter the date of when the battery was first used in a
QuickPanel

device. (This date should reflect the date of first use in any QuickPanel+ device, not just the current device.)

+

6. Enter the current date.

Select the current d ate and from the calendar and click Apply.

Select the date from the calendar and click Next.

44 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

7. Close and re-open the QuickPanel+ Setup Tool dialog box to display the battery life prediction information.

Close and Reopen

Message

Battery Life Prediction Example after Battery

Replacement

Software

For public disclosure

GFK-2847V 45

3.14 Simple Network Management Protocol (SNMP)

The SNMP is an application–layer protocol defined by the Internet Architecture Board (IAB) in RFC1157 that is used
for exchanging management information between network devices. It is a part of the Transmission Control
Protocol/Internet Protocol (TCP/IP) suite.

The QuickPanel+ Operator Interface is enabled as an
Managers

(software tools run independently and are not part of QuickPanel

• Send notification of HMI Alarms as Traps

• Provide live values for SNMP Manager’s GET/GETNEXT Query calls for HMI Tags

The following diagram illustrates the QuickPanel+ operating as the
Traps notification and responding to Query HMI Tag values.

HMI

Tags
Alarms
System

Info

QuickPanel+ Management Information Base (MIB) Overview

The QuickPanel+ SNMP
such. The SNMP Manager uses the MIB to request specific information for the
as needed for the SNMP Managers or Network Management System (NMS).

The MIB is a collection of information for managing network elements. It is a plain text file, self-explanatory, and
prepared based on the Structure of Management Information (SMI), an adapted subset of Abstract Syntax Notation
One (ASN.1)
standard and notation.

Attention

The MIB is comprised of managed objects identified as Object Identifier (Object ID or OID). Each Identifier is unique and
denotes specific characteristics of a managed device. When queried, the return value of each identifier may be
different.

Agent maintains a MIB that describes the managed device parameters like HMI Tags, alarms, and

The QuickPanel+ MIB is follows the SNMP V2c and is also be compatible with SNMP
V1 based on the strictness of MIB compilers supported by SNMP Managers.

SNMP

Agent with the capability to communicate with SNMP

+

Operator Interface) for the following purposes:

SNMP

Agent to communicate with a SNMP Manager for

+

QuickPanel

Device

SNMP

Manager

SNMP

Agent and translates the information

46 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

The following figure displays the MIB tree structure and the private enterprise number allocated by the Internet Assigned
Numbers Authority (IANA) for the GE SNMP products and OID for the QuickPanel

OID for GEIP node: .1.3.6.1.4.1.24893

OID for qppMIB node: .1.3.6.1.4.1.24893.1.5.2.1.1

+

MIB:

It is highly recommended that you pre-load GE MIBs (GEIP-SMI.txt and
GEIP-PRODUCTS-MIB.txt

Attention

into SNMP Managers to avoid any MIB compiler errors.

Contact technical support or download the MIBs GEIP-SMI.txt and
GEIP-PRODUCTS-MIB.txt
copied from the QuickPanel+ device by performing the procedure Export MIB to SD

Card.

in sequence) prior to loading the QuickPanelMIB.mib file

from the Support Site and QuickPanelMIB.mib can be

Software

For public disclosure

GFK-2847V 47

The following figure displays the HMI Alarms notification (TRAP information) with alarm objects as part of the Alarm
Record. The SNMP Manager is notified with the TRAP information when alarms are generated on the HMI running on
a QuickPanel

+

device.

OID for Alarm Trap: .1.3.6.1.4.1.24893.1.5.2.1.1.10

48 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

The following figure displays the list of HMI Tags that the SNMP Manager can query to retrieve live values from the HMI
running on a QuickPanel

+

device.

Note The list of all HMI tags are populated within the hmiTags node of MIB tree and the HMI Tag access level is
currently restricted to Read-only for the SNMP Manager.

OID for starting HMI Tag element (also called Index element): .1.3.6.1.4.1.24893.1.5.2.1.1.50.1.1

If there are 40 HMI tags in total, the last OID would be .1.3.6.1.4.1.24893.1.5.2.1.1.50.1.40

Software

For public disclosure

GFK-2847V 49

The following sections provide the procedures to enable and configure the QuickPanel+ device to operate as a

SNMP

Agent and establish communication with a SNMP Manager.

• Configure Trap Destinations

• Enable or Disable

SNMP

Agent

• Export MIB to SD Card

• Load MIB into SNMP Manager

• Data Types Mapping between PME Project and SNMP

• Establish SNMP Communication

3.14.1 Configure Trap Destinations

TRAP Destinations are configured through the QuickPanel+ Setup Tool by providing the IP Address of the SNMP Manager
to which Traps should be sent. The user can configure two different Trap Destinations (IP Addresses).

Note If you do not want to be notified of Traps, you do not need to configure Trap Destinations.

➢ To configure Trap Destinations

Attention

1. From the Start menu, select System, open the QuickPanel

2. Configure the Trap destination(s) of the SNMP Manager.

3. Click OK to save the changes.

Close the QuickPanel+ Setup Tool, then re-open the tool to view the configured Trap Destination details from the
SNMP Agent tab.

If Trap Destination(s) is/are configured after enabling the
it

is highly recommended that you disable and then re-enable the

SNMP

Agent on the

service on the device.

+

Setup Tool, and select the

SNMP

Agent tab.

Enter the IP Address(es) of the SNMP Manager to which
Traps should be sent.

SNMP

device,

Agent

50 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

3.14.2 Enable or Disable

SNMP communication disabled by default on the QuickPanel+ device for security purposes. To enable or disable SNMP
communication using the QuickPanel+ OS Utilities Settings tool refer to the procedure Enable or Disable

Note Enabling or disabling SNMP communication is a one-time user configuration.

SNMP

Agent

SNMP

Agent.

3.14.3 Export MIB to SD Card

With the
QuickPanelMIB.mib file to a SD Card.

SNMP

Agent is enabled on the QuickPanel+ device, export the QuickPanel+ Management Information Base (MIB)

Attention

It is highly recommended that you pre-load GE MIBs (GEIP-SMI.txt and
GEIP-PRODUCTS-MIB.txt

into SNMP Managers to avoid any MIB compiler errors.

Contact technical support or download the MIBs GEIP-SMI.txt and
GEIP-PRODUCTS-MIB.txt
copied from the QuickPanel+ device by performing the following procedure.

in sequence) prior to loading the QuickPanelMIB.mib file

from the Support Site and QuickPanelMIB.mib can be

➢ To export the MIB to a SD Card

1. Insert a working SD Card into the external card slot on the QuickPanel+ device.

2. From the Start menu, select System, open the QuickPanel+ Setup Tool, and select the

3. Copy the MIB file to the SD Card.

Click Copy MIB T o SD Card.

SNMP

Agent tab.

Software

For public disclosure

GFK-2847V 51

A dialog box displays when the copy is successful or if a failure occurs.

3.14.4 Load MIB into SNMP Manager

After successfully exporting the MIB to a SD Card, archive the QuickPanel+ MIB file to a folder on a machine running with
SNMP Manager.

➢ To load the MIB into the SNMP Manager: from the SNMP Manager tool File menu, select Load the MIBs.

Loading MIBs in 3

rd

Party SNMP Manager

Tool

If there are no errors, the MIB will be loaded successfully and the SNMP Manager will be ready for communication with
QuickPanel

+

device operating as a

SNMP

Agent.

52 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

3.14.5 Data Types Mapping between PME Project and SNMP

PME VIEW Data Types

SNMP Data

Types

BOOL

INTEGER

DINT

INTEGER

LREAL

DISPLAYSTRING

STRING

DISPLAYSTRING

When you configure HMI tags in a PME project and you would like to use them in SNMP communication, all of the HMI
tags are mapped to the corresponding data type in SNMP as listed in the following table. To verify this, review the
Sequence of HMI Tags object in the MIB file.

Note The PME VIEW LREAL data type is mapped to DISPLAYSTRING to retain the data intact.

You can continue to use the data type override/suffix mechanism in PME for the LREAL data type to represent a INT/DINT
if you have configured the data type for driver variables. This enables you to map to the DISPLAYSTRING data type in the
SNMP communication as well.

For example, for the GE SRTP driver, you can override the IO Address of LREAL variable LREALVar data type as %R100
[INT]. This maps LREALVar to DISPLAYSTRING in the MIB file.

3.14.6 Establish SNMP Communication

Attention

SNMP communication requires that both the QuickPanel+ device and the SNMP
Manager running on a machine are connected on a valid Ethernet network.

➢ To establish SNMP communication with the QuickPanel+ device

1. Download the Project to the network connected QuickPanel+ device and start Runtime.

2. Configure the Trap Destinations with the IP Address of the SNMP Manager.

Note If you do not want to be notified of Traps, you do not need to configure Trap Destinations.

3. Enable a

4. Export the MIB to a SD Card.

5. Auto-discover or connect the QuickPanel+ SNMP

SNMP Manager tool.

The SNMP Manager communicating with QuickPanel
Alarms/Trap notification from the QuickPanel

SNMP

Agent.

Agent from the SNMP Manager. Once connected, load the MIB to the

+

device can query values for HMI Tags and receive

+

device operating as a

SNMP

Agent.

Tip � If you get out of sequence in the steps for configuring Traps and starting the SNMP service to establish the SNMP
communication, enable or disable the

SNMP

Agent again using the QuickPanel+ OS Utilities Setting tool.

Software

For public disclosure

GFK-2847V 53

3.15 ScreenSaver

QuickPanel+ shall have the ability to run a video as a screensaver. The configuration for this can be done at the
‘ScreenSaver’ Tab in the ‘QuickPanel+ Setup Tool’ window.

The dialog provides the following options

1) Enabiling\Disabling the ScreenSaver

2) Browsing the video file to be run as the ScreenSaver

3) The elapse idle time setting to trigger the ScreenSaver

54 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

Notes

Pre-installation Checks

For public disclosure

GFK-2847V 55

4 Pre-installation Checks

This chapter provides information and procedures to perform pre-installation checks of the QuickPanel+ Operator

Interface. Before installing and using the QuickPanel

• Unpacking and Inspection

• Basic Setup

• Initial Startup

• Runtime Setup

• Firmware Updates

• Shutdown

4.1 Unpacking and Inspection

Upon receipt of the QuickPanel+ Operator Interface, carefully inspect all shipping containers for damage. If any part of
the system is damaged, notify the carrier immediately. Save the damaged shipping container for inspection by the
carrier. It is the
consignee’s responsibility to register a claim with the carrier for damage incurred during shipment.

Note For phone numbers and email addresses, refer to the section, Contact Information.

After unpacking the unit, record all serial numbers. These are needed to contact Customer Care during the warranty
period. Save all shipping containers and packing material for future transport or shipping. Verify that all system
components have been received and agree with the order. If the system received does not agree with your order,
contact Customer Care.

+

, complete the following procedures:

Before initial powerup, inspect the unit for loose or damaged components. If damage is found (such as bent component
leads or loose components), contact GE Intelligent Platforms for additional instructions.

Do not apply power to the unit if it has visible damage. Applying power to a unit
with damaged components may cause additional damage.

Caution

56 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

+

QuickPanel

Operator Interface

Battery (Qty 1) (pre- installed)

Serial Port Connector (Qty 1)

Power Connector (Qty 1)

Mounting Brackets (Qty 4)

Protective Sheet (Qty 1) (not shown) Gasket

( Qty 1) (not shown, pre- inst alled)

IC755CxWxxCDx Example Package Contents

Pre-installation Checks

For public disclosure

GFK-2847V 57

4.2 Basic Setup

The QuickPanel+ Operator Interface is shipped ready for use after initial configuration.

To power up the unit, connect a dc power supply using the supplied quick-connect plug. Depending on the application,
you may also want to connect and configure optional input devices, communications ports, and expansion adapters.

Power

Warning

Warning

Supply

To avoid personal injury or damage to equipment, ensure that the dc supply is
disconnected from power and the leads are not energized before attaching them to
the unit's power supply plug.

If this equipment is used in a manner not specified by the manufacturer,
equipment protection may be impaired.

Optional USB Keyboard and

Basic Setup

Diagram

Mouse

Optional

Serial

I/O

Optional Serial

Ethernet

Connection

I/O

58 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

4.3 Initial Startup

You will need the following:

• Safety Extra Low Voltage (SELV) and Limited Energy Circuit or

• The power terminal block is supplied with the product. For voltage and requirements, refer to the Input Power
specifications in the table, General Specifications.

• The mating power terminal block supports stranded 30 to 14 AWG
(0.05 to 2.00 mm

2

) wires. The user calculates proper gauge wiring for current carrying capacity and loss according to

local regulations.

• At a minimum, the cable must be rated for 75°C (167 °F) or more.

• USB-compatible keyboard (optional)

• USB-compatible mouse (optional)

4.3.1 Connecting Input Power

➢ To connect input power

1. Verify that the power cable is not energized.

2. Loosen the screw clamps on the mating power connector.

3. Strip the insulation from the power cables.

4. Secure the power cable to the mating connector, noting polarity, and

tighten the screw clamps. The torque for the attaching screws is 0.3 Nm
(2.66
in-lb).

5. Apply dc power to the unit. During normal startup and operation, the
QuickPanel

• Solid amber while the QuickPanel+ is starting up

• Solid green during normal operation

6. Once power is applied, the QuickPanel
splash screen is the initial display.

➢ To skip running any programs included in the StartUp folder: tap

Don’t run Startup programs. The Microsoft Windows Embedded

Compact 7 operating system starts automatically.

+

status LED indicator displays as follows:

+

begins initializing. The

SELV

and Class 2 dc power supply.

M2.5

Mounting

FG

GND +24 V dc

Power Connector

clamps

Screw

M2

clamps

Pre-installation Checks

For public disclosure

GFK-2847V 59

4.3.2 Initial Configuration

Perform the following procedure during initial startup.

➢ To configure the QuickPanel

1. Tap Start , point to Settings, then tap Control Panel.

2. Configure the system clock.

+

display

From the

Date and Time

3. From the Control Panel, double-tap System to configure a Network Device Name. Many applications, including Proficy

Historian, require a unique Device Name.

Attention

4. From the Control Panel, double-tap Network and Dial-up Connections to configure network settings.

5. Run the Backup Utility to save the settings.

It is recommended to set a unique Device Name for the QuickPanel+ to avoid
future conflicts.

4.4 Runtime Setup

To download an application to a QuickPanel+ Operator Interface, set up a data link between the unit and the
development workstation. Refer to the section, Ethernet for IC755CxS06RDx, IC755CxWxxCDx and IC755CxSxxCDx, and
the PME online help, Downloading a Machine Edition Project.

60 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

4.5 Firmware Updates

Update the unit to the most recent released version of the firmware, with the latest feature upgrades and issues
addressed. Firmware updates for the QuickPanel

+

are available on the Support website.

Note The firmware update will remove the application and change the IP Address of the QuickPanel

+

Operator Interface.

Note The firmware package contains encrypted .nbo files. Use the PreUpdate.exe tool to decrypt the .nbo files before
using them for upgrade.

4.6 Shutdown

There are no specific dangers associated with a power failure or other unplanned shutdown of the QuickPanel+ unit. In
general, programs are retained in flash memory and user data can be retained in BBSRAM. Some operating system
settings are retained only with user intervention. Perform the following procedure to properly shut down the
QuickPanel

➢ To shut down the QuickPanel+ unit

1. Quit any programs that are running and wait for all file operations to complete.

2. If you have not changed operating system settings (for example, brightness or touchscreen sensitivity), or do not

3. Run the Backup Utility to save changes to operating system settings. When the Backup window displays Completed

+

unit.

want to save the changes, remove ac power from the dc supply.

Successfully, remove power from the dc power supply connected to the QuickPanel+ unit.

Mounting and Installation

For public disclosure

GFK-2847V 61

5 Mounting and Installation

This chapter provides the following procedures to mount and install the QuickPanel+ Operator Interface:

• Protective Sheet Installation

• Mounting Location

• Panel Mounting

• VESA Arm Mounting

• Battery Installation and Replacement

• Connectors

5.1 Protective Sheet Installation

➢ To install the protective sheet

1. Remove the protective film from the QuickPanel+ display screen.

2. Wipe the display unit of any dust or fingerprints.

3. Peel back a corner of the clear side of the protective sheet.

4. Begin applying the corner to the display screen.

5. Slowly apply the rest of the protective sheet, smoothing out as you go.

6. Peel the green curing film from the protective sheet.

62 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

5.2 Mounting Location

Note Refer to the section, Environmental Specifications.

When mounting the QuickPanel+ Operator Interface, make sure the mounting area allows room to insert and remove
the SD card, cables, and mounting brackets. Select a location that allows natural convection air flow from bottom to
top of the QuickPanel+ enclosure. Do not mount the QuickPanel+ at an angle more than 30° from the vertical, as
illustrated in the following figure.

Mounting

Angle

Mounting and Installation

For public disclosure

GFK-2847V 63

5.3 Panel Mounting

To mount the QuickPanel+ in an enclosure, you will need the following equipment:

• One #2 Phillips head screwdriver

• Mounting brackets (supplied)

The mounting holes for IC755CxS06RDx, IC755CxW07CDx, and IC755CxS10CDx are located on the top and bottom sides
of the unit.

IC755CxS06RDx Mounting

Holes

IC755CxW07CDx Mounting

Holes

64 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

IC755CxS10CDx Mounting

Holes

The IC755CxS12CDx and IC755CxS15CDx mounting holes are located on the top, bottom, and sides of the unit.

IC755CxS12CDx Mounting

Holes

Mounting and Installation

For public disclosure

GFK-2847V 65

IC755CxS15CDx Mounting

Holes

66 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

228 mm

(

8.98 in)

128.50 mm (5.06 in)

305

m

m (12.01 in)

210 mm (8.27 in)

5.4 Mounting and Installation Procedure

Observe the following guidelines to properly mount and install the QuickPanel+ Operator Interface:

Note To order replacement gaskets, refer to the part number listed in Appendix B.

• The enclosure should be of metal material.

• The metal enclosure panel should ensure proper thickness and rigidity suitable to minimize impact to the QuickPanel
unit.

• The recommended torque for the plastic back cover and interior metal cover for the 10, 12, and 15” QuickPanel
display units that is accessed for panel updates and serial port DIP Switches is 0.5 Nm (4.4 in-lb).

• To avoid gasket degradation, limit repeated insertions or removals of the unit and retightening of the mounting
clips. For full protection, always use a fresh gasket.

• The unit will not fit through the cutout with any cables connected, or with the power supply plug inserted in the

socket.

Caution

➢ To install the QuickPanel

1. Cut an opening in the panel according to the specifications in the following figures.

Note Panel cutout tolerances are +0.50, –0.00 mm (+0.02, –0.00 in).

When installing the QuickPanel+ into the panel, pay careful attention while
handling the unit so it does not drop and damage the unit.

+

183.50 mm (7.22 in)

266 mm (10.47 in)

Panel T

1.0 to 5.0

(0.04 to 0.20 in)

Panel T

1.6 to 5.0

(0.06 to 0.20 in)

hickness

hickness

:

mm

IC755CxSO6RDx or

Panel Cutout

:

mm

IC755CxS12CDx Panel Cutout Dimensions

IC755CxW07CDx

Dimensions

302 mm ( 11.89 in)

hickness

Panel T

1.6 to 5.0

(0.06 to 0.20 in)

Panel T

hickness

1.6 to 5.0

(0.06 to 0.20 in)

:

mm

IC755CxS10CDx Panel Cutout Dimensions

379 mm (14.92 in)

:

mm

IC755CxS15CDx Panel Cutout Dimensions

+

+

Mounting and Installation

For public disclosure

GFK-2847V 67

2. Verify that the gasket is present and properly seated in the bezel channel located on the sides of the unit.

Display Unit

Torque Range

IC755CxS06RDx

0.3 Nm (2.66 in-lb)

IC755CxW07CDx

0.3 Nm (2.66 in-lb)

IC755CxS10CDx

0.7 Nm (6 in-lb)

IC755CxS12CDx

1.0 to 1.2 Nm (8.9 to 10.6 in-lb)

IC755CxS15CDx

1.0 to 1.2 Nm (8.9 to 10.6 in-lb)

3. Insert the QuickPanel+ into the mounting panel cutout.

4. Insert the hook of the mounting bracket into the mounting hole as displayed in the following figure.

5. Tighten the screws on the mounting bracket in a clock-wise direction.

Torque Range for Mounting Clamp Screws

68 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

75

mm

(2.95

in)

100 mm

(3.94 in)

5.5 VESA Arm Mounting

Display Unit

Torque Range

IC755CxS06RDx

0.7 to 0.8 Nm (6.2 to 7.1 in-lb)

IC755CxW07CDx

0.7 to 0.8 Nm (6.2 to 7.1 in-lb)

IC755CxSxxCDx

1.0 to 1.2 Nm (8.9 to 10.6 in-lb)

The QuickPanel+ unit can be installed on a commercially available Video Electronics Standards Association (VESA) MIS-D
arm, stand, or apparatus that complies with the UL1678 standard.

Note Refer to the mounting arm manual for instructions.

➢ To VESA mount the QuickPanel

following figures).

+

unit: use the mounting holes located on the back of the unit (displayed in the

The mounting holes for IC755CxS06RDx and IC755CxW07CDx attach with M4 screws that are 6 mm (0.24 in) or less in
length.

The mounting holes for IC755CxSxxCDx attach with M4 screws that are 8 mm (0.32 in) or less in length.

Torque Range for Mounting M4

Screws

75 mm

75 mm

(2.95

in)

m
m
5

7

IC755CxW07CDx or IC755CxS06RDx VESA Mounting Holes

100 mm

(3.94 in)

IC755CxSxxCDx VESA Mounting

Holes

Mounting and Installation

For public disclosure

GFK-2847V 69

5.6 Battery Installation and Replacement

Batteries may present a risk of fire, explosion, or chemical burn if mistreated. Do
not crush, disassemble, short-circuit, or dispose of in fire.

Warning

Warning

Caution

Attention

Use of batteries not specified for use with the QuickPanel+ product may present a
risk of fire or explosion.

Do not recharge, disassemble, heat or incinerate lithium batteries.

Dispose of lithium batteries in accordance with federal, state, and local regulations.
Be sure to consult with the appropriate regulatory agencies before disposing of
batteries.

1) Replacing the battery should only be performed by trained personnel and in
a non-hazardous location.

2) If the QuickPanel+ Operator Interface is VESA mounted, detach from the VESA
arm when replacing the battery.

3) The battery should only be replaced when the unit is powered off.

4) Care should be taken to protect and insert the battery with correct polarity.

5) Do not use any metallic item to remove the battery (such as screwdrivers,
knives, pliers, and so forth).

6) Be careful to not drop the battery or any associated screws into the unit.

7) Be careful of edges on internal sides of the enclosure and frame.

The PC controller does not start automatically when the battery is replaced in
QuickPanel
using the #Command in the Proficy Machine Edition (PME) runtime.

+

Operator Interface. After battery replacement, start the controller

70 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

5.6.1 IC755CxS06RDx

➢ To install or replace the battery for IC755CxS06RDx

Caution

1. Remove the battery cover by pressing down while sliding outward.

Replace the battery for the IC755CxS06RDx only with GE battery part number
IC755ACCBATT.

IC755CxS06RDx Battery Cover

Removal

2. Connect the battery harness connector to the header, noting keyed orientation.

Battery Part Number

I

C755ACC

BATT

IC755CxS06RDx Battery Harness Connection

3. Verify that the positive (red) is down and negative (black) is up.

Mounting and Installation

For public disclosure

GFK-2847V 71

4. Wrap the harness connector around to match the following figure. Do not let the harness connector go above the tab.

Harness Connector

Orientation

5. Slide the battery cover into place, taking care not to pinch the harness connector.

72 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

5.6.2 IC755CxW07CDx

➢ To install or replace the battery for the IC755CxW07CDx

Caution

1. Remove the battery cover by pressing down while sliding outward.

Replace the battery for the IC755CxW07CDx only with GE battery part number
IC755ACCBATT.

2. Connect the battery harness connector to the header, noting keyed orientation.

IC755CxW07CDx Battery Cover Removal

Battery Part Number

IC755ACCBATT

3. Verify that the positive (red) connection is down and the negative (black) connection is up.

Battery Harness

Connection

Mounting and Installation

For public disclosure

GFK-2847V 73

4. Wrap the harness connector around to match the following figure. Do not let the harness connector go above the tab.

Harness Connector

Orientation

5. Slide the battery cover into place, taking care not to pinch the harness connector.

74 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

5.6.3 IC755CxSxxCDx

➢ To install or replace the battery for the IC755CxSxxCDx

Caution

1. Remove the screws (quantity 7) from the back cover.

Replace the battery for the IC755CxSxxCDx only with GE battery part number
IC755ACCBATTNL.

2. Gently press on either side tab to release the back cover.

3. Lift up and remove the back

cover.

IC755CxSxxCDx Screw Locations (Back Cover)

Side Tab for Cover Release

Mounting and Installation

For public disclosure

GFK-2847V 75

The battery will be exposed on the back of the unit.

Battery Part Number IC755ACCBATTNL

IC755CxSxxCDx

Battery

4. Gently remove the coin battery and replace with a new one, noting the polarity of the battery.

5. Replace the battery cover and tighten all screws to 0.5 Nm (4.4 in-lb).

76 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

5.7 Connectors

Pin #

Signal Name

Pin-out

1

+24 V

dc

2

GND

IC755CxSxxCDx supports both +12 V dc or +24 V dc IN

Pin #

Signal Name

Pin-out

1

TX+

2

TX-

3

RX+

4

NC

5

NC

6

RX-

7

NC

5.7.1 Power Connector Pin-out for IC755CxS06RDx, IC755CxW07CDx, and

IC755CxSxxCDx

Note Refer to the section Connecting Input Power.

Connector: Terminal Euro (Tyco Electronics 284539-3)
Mating Connector: (Tyco Electronics 284510-3)

†

3

†

5.7.2 Ethernet for IC755CxS06RDx, IC755CxW07CDx, and IC755CxSxxCDx

Note Refer to the section Ethernet Port LED Operation.

The QuickPanel
(unshielded-twisted pair, CAT 5) to the unit through the RJ-45 connector(s) on the bottom of the enclosure. LED indicators
on the port indicate channel status. The port can be accessed by Windows Embedded Compact 7 network
communications or by your application.

+

display is equipped with 10Base-T/100-Base-TX Ethernet port(s). Connect an Ethernet network cable

FG

1 3

5.7.2.1 Ethernet Port Details

Interface: Ethernet 10BASE-T/100BASE-TX

8

Note Dual Ethernet ports are separate ports (only applicable to QuickPanel

NC

Yellow Green

8 1

+

IC755CxSxxCDx 10, 12, and 15" display units)

Mounting and Installation

For public disclosure

GFK-2847V 77

5.7.2.2

IP

Address Setting

The QuickPanel+ Operator Interface provides two methods to set an IP address:

• DHCP (Dynamic Host Configuration Protocol)

+

The network server assigns an IP address during QuickPanel

initialization. There must be a DHCP server on the
connected network for a valid IP address to be assigned. Contact your network administrator to ensure correct
DHCP
server configuration.

• Manual Method
Specify the numeric addresses obtained from your network administrator for the QuickPanel

+

IP Address, Subnet

Mask and Default Gateway (if applicable).

Note Run the Backup utility to save the settings.

78 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

5.7.3 Serial Port Details

Pin

#

Signal Name

1

TXD

2

RXD

3

RTS

4

CTS

5

SGND

5.7.3.1 IC755CxS06RDx

Adhere to the following guidelines:

• A terminal block is supplied with the unit.

2

• The mating terminal block supports stranded 30 to 14 AWG (0.05 to 2.00 mm

• At a minimum, the cable must be rated for 75°C (167 °F) or more.

• Secure the serial cable to the mating connector while noting signal orientation and tighten the screw clamps.

• The torque for the attaching screws is 0.3 Nm (2.66 in-lb).

Connectors: Euro Terminal (Tyco Electronics 284539-5)
Mating Connectors: Tyco Electronics 284510-5

Serial Port COM1 Details

Interface: RS-232

COM1 Pin Details

) wires.

Pin 1

Pin 5

IC755CxS06RDx Serial Port COM1 Pin-out

Mounting and Installation

For public disclosure

GFK-2847V 79

5.7.3.2 IC755CxW07CDx

Signal Name

1

TXD

2

RXD

3

RTS

4

CTS

5

SGND

Adhere to the following guidelines:

• A terminal block is supplied with the unit.

2

• The mating terminal block supports stranded 30 to 14 AWG (0.05 to 2.00 mm

) wires.

• At a minimum, the cable must be rated for 75°C (167 °F) or more.

• Secure the serial cable to the mating connector while noting signal orientation and tighten the screw clamps.

• The torque for the attaching screws is 0.3 Nm (2.66 in-lb).

Serial Port COM1 Details

Interface: x1 RS-232
Connectors: Euro Terminal (Tyco Electronics 284539-5)
Mating Connector: (Tyco Electronics 284510-5)

Pin

#

COM1 Pin

Details

Pin 1

Pin 5

IC755CxW07CDx Serial Port COM1 Pin-out

80 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

5.7.3.3 IC755CxSxxCDx

Note For an IC755CxS12CDA serial port, refer to Appendix C IC755CxS12CDA Serial Port Details.

Adhere to the following guidelines:

• Terminal blocks are supplied.

2

• The mating terminal blocks support stranded 30 to 14 AWG (0.05 to 2.00 mm

) wires.

• At a minimum, the cable must be rated for 75°C (167 °F) or more.

• Secure the serial cable to the mating connector while noting signal orientation and tighten the screw clamps.

• The torque for the attaching screws is 0.3 Nm (2.66 in-lb).

Connectors: Euro Terminal (Tyco Electronics 284539-5)
Mating Connectors: Tyco Electronics 284510-5

Serial Port COM1 Details

Interface: RS-232C

Pin #

1
2
3
4
5

COM1 Pin

Details

Signal

TXD
RXD
RTS
CTS

SGND

Name

COM1 COM2

Pin 1 Pin 5

IC755CxSxxCDx Serial Port COM1 Pin-out

Mounting and Installation

For public disclosure

GFK-2847V 81

DIPSW

Bit

ON/OFF

1 OFF 2 OFF

3 OFF

4 OFF

5 OFF 6 OFF

7 OFF

8 OFF

1 ON 2 ON 3 ON 4 ON

DIPSW

Bit

ON/OFF

1 OFF 2 OFF

3 OFF

4 OFF

5 ON 6 ON 7 OFF 8 ON

1 ON

2 OFF 3 OFF 4 OFF

RS–232C

RS–485

Signal Name

Signal Name

DATA+

2 RXD TXD-

DATA-

DATA+

4 CTS RXD-

DATA-

5 SGND SG SG

Full-duplex RS–485 is backwards compatible to RS–422 mode.

SW2

SW3

COM2 DIP Switch Setting for

Serial Port COM2 Details

Interface: RS-232C/485 (default is RS-485 Half-duplex)

COM2 Pin

Details

SW4

SW5

RS-232C

Pin #

1

3

†

‡

Pins 1-3 and 2-4 are connected internally.

Signal Name

COM1

(Full-duplex†)

TXD

RTS

Pin 1 Pin 5

IC755CxSxxCDx Serial Port COM2 Pin-out

COM2

TXD+

RXD+

(Half-duplex†)

‡

‡

‡

‡

82 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

DIP SW

Bit

ON/OFF

1 ON 2 ON

3 OFF

4 OFF

5 ON

6 ON

7 OFF 8 OFF

1 OFF 2 OFF 3 OFF 4 OFF

DIP SW

Bit

ON/OFF

1 OFF

2 OFF 3 OFF 4 OFF 5 ON 6 ON 7 OFF 8 ON

1 OFF

2 ON 3 OFF 4 OFF

Example of Full-duplex (RS–422 Mode)

Connection

SW2

SW3

COM2 DIP Switch Setting for

SW4

SW5

RS–422

Example of Half-duplex (RS–485 Mode) Connection

Mounting and Installation

For public disclosure

GFK-2847V 83

DIPSW

Bit

ON/OFF

1 ON 2 ON

3 ON

4 ON

5 ON 6 ON

7 OFF

8 OFF

1 OFF 2 OFF 3 OFF 4 OFF

DIPSW

Bit

ON/OFF

1 OFF 2 OFF

3 ON

4 OFF

5 ON 6 ON 7 OFF 8 ON

1 OFF

2 ON 3 OFF 4 ON

SW2

SW3

COM2 DIP Switch Setting for

SW4

SW5

RS–485

84 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

5.7.4 Universal Serial Bus (USB) Ports

Signal Name

1

USB_VCC

USB_D-

USB_D+

Signal Name

1 VCC

2 D-

3 D+

4 NC

5 GND

5.7.4.1 USB Host Port Details for IC755CxS06RDx, IC755CxW07CDx, and
IC755CxSxxCDx

The QuickPanel+ has two full-speed USB 2.0 host ports. A variety of third party USB peripheral devices are also
available. Each connected USB device requires a specific driver. The driver supplied with the QuickPanel
keyboard or mouse support; other devices require installation of the custom driver software.

Interface: USB 2.0
Number of Ports: Two
Connectors: Type-A connector
Maximum Supply Current: 0.5 A (per port)

Pin #

2
3

Pin-out

+

is for optional

4

USB_GND

5.7.4.2 USB Device Port Details for IC755CxS06RDx, IC755CxW07CDx, and
IC755CxSxxCDx

The USB device port allows the QuickPanel+ Operator Interface to be used as Slave

device. Interface: USB 2.0
Number of Ports: One
Connectors: Type-B Mini connector

Pin #

Pin-out

5 1

Mounting and Installation

For public disclosure

GFK-2847V 85

5.7.4.3 Serial USB and Ethernet USB Adapters for All Models Using Adapters

Signal Name

1 GND

2 Lineout R

Signal Name

1 GND

2 Lineout R

Recommended adapters are as follows:

• Serial USB adapters based on FTDI chipset

• Ethernet USB adapters based on ASIX AX88179 or AX88772B

Note For serial USB adapters (USB to RS-485 and such), configure the correct COM port depicted in the System Info
tool and configure the same port in the Driver configuration. In the System Info tool, the USB ports shown (COM3,
COM4) are
based on the USB connection sequence on the device, and need to be configured accordingly.

5.7.4.4 Wi-Fi Support for All Models Using Adapters

Recommended USB wifi adapters based on the Ralink chipset are as follows:

• RT–2070

• RT–2870

• RT–3070

• RT–3071

• RT– 3072

5.7.5 Audio (LINE OUT) Details for IC755CxS06RDx, IC755CxW07CDx, and

IC755CxSxxCDx

Interface: LINE OUT (stereo)
Number of Ports: One
Connectors: φ3.5 mm jack
Maximum output level: 1 Vrms

Pin #

Pin-out

1
2

3

Lineout L

3

5.7.6 Audio (MIC IN) Details (Only Applicable to IC755CxS06RDx and

IC755CxW07CDx)

Interface: MIC IN (monaural)
Number of Ports: One
Connectors: φ3.5 mm jack
Maximum output level: 250 mVrms

Pin #

3

Lineout L

Pin-out

1
2

3

86 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

5.7.7 SD Card Slot and Storage

The QuickPanel+ is equipped with one standard SD Card port. SD/SDHC memory cards are supported. The SD card slot
is spring-loaded for easy insertion and removal.

Note Micro SD slot is not supported on the 6” display unit (IC755CxS06RDx).

Connectors: SD card slot (push in-push out
method) Card support: SD/SDHC memory card
Maximum capacity: 32 GB

Note During insertion, observe the orientation of the SD card as displayed in the following figures.

IC755CxS06RDx SD Card

Location

IC755CxW07CDx SD Card

Location

Mounting and Installation

For public disclosure

GFK-2847V 87

IC755CxSxxCDx SD Card

Location

88 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

Notes

Operation

For public disclosure

GFK-2847V 89

6 Operation

6.1 Touchscreen Display

The QuickPanel+ Operator Interface features a LED Backlight LCD touchscreen display with two-point touch
The

touch technology is based on projected capacitance that allows finger tracking without pressured contact. It is
conducive to smooth scrolling and multi-touch gesturing capability. Display brightness and backlight operation can be
configured using
the QuickPanel

Caution

+

Setup tool available in the program system menu.

Although we recommend the use of the protective sheet, do not operate the
touchscreen with any hard materials, such as a screwdriver. This could damage
the touchscreen display.

Note IC755CxS06RDx (6” display) is an Analog Resistive touch display that does not support two-point touch
capability. Single point gestures such as swipe, pan, and double-tap are supported.

6.1.1 Display Brightness Adjustment

➢ To adjust the brightness of the display

1. Open the QuickPanel+ Setup Tool and select the Backlight tab to display the Backlight Display Properties window.

2. Set the backlight brightness value.

From the Setting backlight
brightness drop-down menu ,

select a value between 1
(lowest setting ) and 16
(highest setting ).

3. Tap OK to exit the QuickPanel

4. Run the Backup Utility to save the settings.

+

Setup Tool.

technology.

90 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

6.1.2 Display Backlight Configuration

➢ To configure the display backlight

1. Open the QuickPanel+ Setup Tool and select the Backlight tab to display the Backlight Display Properties window.

2. Set the backlight to automatically turn off in a specific amount of time.

Select Automatically turn off
the backlight . From the drop-

down menu, select a time
between 15 sec to 2 hr.

3. Tap OK to exit the QuickPanel

+

Setup Tool.

4. Run the Backup Utility to save the settings.

Operation

For public disclosure

GFK-2847V 91

6.1.3 Touchscreen Re-calibration

The QuickPanel+ touchscreen is shipped pre-calibrated. However, if there are any issues with touchscreen
responsiveness, it may need to be re-calibrated.

➢ To re-calibrate the touchscreen

1. Open the QuickPanel+ Setup tool.

2. Select the TouchPanel tab.

3. Select Recalibrate Touch Screen.

4. Select Recalibrate Touch Sensor.

Note During IC755CxS06RDx or IC755CxW07CDx touchscreen sensor re-calibration, the user is prompted to
activate a

switch located in the battery compartment. This is not applicable to any other display units.

5. Remove the battery cover and press the switch.

6. Replace the battery

cover.

Switch

Touchscreen Sensor Calibration Switch

Battery

Cover

92 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

6.2 Keyboard Configuration

The QuickPanel+ Operator Interface can be configured to use either or both a hardware keyboard and a software
emulation keyboard as operator data input devices. Typically, an optional external hardware keyboard is used when
in development mode, while the included Soft Input Panel (SIP) is more applicable in an operational environment.

6.2.1 External Keyboard (Optional)

Any USB-compatible keyboard may be used as an input device for the unit. The USB driver for the keyboard is included
with the operating system and no configuration is required. To use an external keyboard, connect the keyboard to the
unit using the USB cable.

6.2.2 Soft Input Panel

The Soft Input Panel (SIP) is a touchscreen keyboard that may be used in place of a standard hardware keyboard. An
icon in the system tray enables the user to view or hide the SIP.

➢ To show or hide the SIP: from the system tray located on the task bar, tap the icon and select Hide Input Panel.

Note When visible, the SIP can be moved around the screen by dragging the title bar to reveal parts of the screen that
would be obstructed from view by the SIP.

6.3 Mouse

Any USB-compatible mouse may be used as an input device for the unit. The USB driver for the mouse is included with
the operating system and no configuration is required. To use an external mouse, plug it into the appropriate port.

Operation

For public disclosure

GFK-2847V 93

6.4 Printing

Warning

USB-connected printers will violate the electrical compliance ratings. They can only
be used for maintenance and are not supported as a standard service.

The QuickPanel+ Operator Interface supports printing with PCL v5 compatible laser and inkjet printers. The printer can
be connected by either USB (on models with USB ports) or by a network shared printer over Ethernet. The control panel
applet Printers is used to configure the port connection and other general printing options.

For the fastest printing performance, select draft mode and portrait orientation, and disable color for print settings.
These settings also minimize the amount of memory needed to print a document.

The built-in driver has a document spooling function to improve GUI performance. This spooler supports only one
document at a time. However, on an Ethernet connected printer, the print server usually supports multiple documents in
its queue. Windows Embedded Compact 7 does not support the ability to observe which documents are queued up at
the printer.

For a list of printers that are compatible with that QuickPanel+ Operator Interface, refer to the document Third Party Device
Compatibility (KB8259).

94 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

6.5 Memory

6.5.1 DRAM Memory

The QuickPanel+ Operator Interface is equipped with Dynamic RAM (DRAM). Part of the DRAM is reserved for the
Windows operating system and is not accessible by user applications. The remaining memory is split between two
functions: an object store for temporary file storage and the main memory for running programs.

Typically, compressed programs stored in flash memory are expanded and moved to DRAM for execution. Temporary
storage of program variables or data files is also provided by DRAM. Any data stored in DRAM is not retained through a
power cycle or restart.

The split between program memory and storage memory can be adjusted as necessary to make more room for one or
the other, depending on specific application needs. For example, if an application is short of memory, alter the DRAM
memory
allocation from the System Properties window.

Setting the Program Memory too low may prevent additional applications from
starting, or may cause currently running applications to fail due to lack of
memory.

Setting the Storage Memory too low may prevent the saving of files into the
object store portion of the file system, which may also cause application
failures.

Caution

For the QuickPanel+ 6” display unit, setting the Storage Memory too high or
extreme
or windows and it may also require a power cycle. It is recommended that the
Storage Memory is set to a valid limit.

to

limit may make the device become unresponsive to launch any applications

Operation

For public disclosure

GFK-2847V 95

6.5.2 Memory Allocation Modification

➢ To change the memory allocation

1. From the Control Panel, double-tap System to display the System Properties window.

2. From the Memory tab, drag the slider bar to divide into Storage and Program memory. The amount of memory

allocated to and used by each area is displayed in the window. The blue slider bar indicates the current amount of
unallocated SDRAM and determines the boundaries within which the slider can move.

System Memory Slider

Bar

Note Storage memory is limited to a maximum of 128 MB. Using the slider bar to increase storage memory will

provide more RAM-based storage in the folder \Object Store.

3. Tap OK to apply the new setting.

4. Run the Backup Utility to save the settings.

96 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

Notes

Secomea Security (Optional)

For public disclosure

GFK-2847V 97

7 Secomea Security (Optional)

7.1 Secomea Configuration Tool

Note The SiteManager™ and its related GateManager™, LinkManager™ and LinkManager™ Mobile products are

licensed, sold, and supported by Secomea and Secomea’s licensed distributors. Additional information, is available at

www.secomea.
com.

Secomea SiteManager software (also known as the Secomea Configuration tool) is installed on QuickPanel
Secomea Configuration tool enables the user to configure and enable the QuickPanel

Note It is recommended to have a Network Architect on-site and working with Secomea team to enable this functionality.

➢ To access the Secomea Configuration tool and enable the QuickPanel

1. From the QuickPanel+ Start menu, select Programs to display the Secomea Configuration tool window.

2. Enable the QuickPanel+ device on the Secomea network.

+

on the Secomea network

+

device on the Secomea network.

Select Enable Remote
Management and enter the
values provided to you by
the Secomea team.

+

products. The

Note The Appliance Name can be any name but should be unique so that Secomea network can identify the

device. Proxy Address allows the user to connect from their local network with firewall enabled and blocking ports

80, 443, and

11444. The SiteManager will attempt to establish a connection with and without proxy.

98 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

7.2 Secomea Products

Note Activation and deployment of the Secomea product features is optional. SiteManager, GateManager, and

LinkManager products are licensed, sold, and supported by Secomea and Secomea’s licensed distributors. QuickPanel
customers wanting
to activate licenses for Secomea products can do so at www.secomea.com.

The available Secomea SiteManager (embedded on QuickPanel

+

), GateManager, and LinkManager products are

described as follows:

SiteManager is a device-monitoring front-end feature for multiple industrial devices on a location. Working with
GateManager and LinkManager, it ensures uninterrupted and secure access to remote devices over the Internet or a
private Wide-area Network (WAN) for all users.

LinkManager is an off-the-shelf software component in Remote Device Management Solutions from Secomea that
provides security for external programming and monitoring applications. LinkManager Mobile provides similar
functionality for mobile devices.

GateManager is the central component of Secomea’s Industry solution. The GateManager M2M Server operates as a
termination point for all LinkManagers and SiteManagers. All connections and the encrypted traffic between
LinkManagers
and devices controlled by SiteManagers are handled by the GateManager, where all events are also logged.

Note The GateManager is typically offered as a service hosted by Secomea. Users will receive an isolated domain on the
GateManager and benefit from central hosting and back-up by Secomea. Or, the user can host their own GateManager.

Additionally, other devices such as PLCs and PCs (in addition to the QuickPanel
Secomea network to be part of Secured Communication using the Add Agents feature in the SiteManager GUI. This
can be achieved using extended license feature from Secomea.

Note Secomea products installed throughout the application as suggested by the following figure do not intrinsically
provide the level of security associated with firewalls. The network architect needs to satisfy himself or herself that the
security level required by the application is present in the overall implementation.

+

) can be added as new agents on the

+

Secomea Security (Optional)

For public disclosure

GFK-2847V 99

Secomea Products used with QuickPanel+ in Application

100 GFK-2847V

For public disclosure

QuickPanel⁺ Operator Interface User

Notes