Process Automation Control Systems
PACSystems RX3i Controller
Analog I/O Modules (Input)
GE offers easy-to-use analog modules and HART analog modules for control processes such as
flow, temperature and pressure.
IC694ALG232 IC694ALG233 IC695ALG600
PACSystems RX3i
Analog Input, Voltage, High Density
(16 Channel) 16 Bit with
Product Name
Lifecycle Status Active Active Active
Module Type
Backplane Support No Backplane Restrictions No Backplane Restrictions Universal Backplane Only. Uses PCI Bus.
Number of Slots Module
Occupies on Backplane
Range
HART Support
advanced diagnostics
Analog Input Analog Input Universal Analog Input
1 1 1
-10 V to +10 V, 0 to 10 V 0-20 mA, 4-20 mA,
N/A N/A N/A
PACSystemsRX3i
Analog Input, Current, High Density
(16 Channel) 16 Bit with
advanced diagnostics
4-20 mA Enhanced
PACSystems RX3i Analog Input.
Configurable per channel for Current,
Voltage, RTD, Thermocouple and
Resistive. High Density (8 Channel)
Requires High Density Terminal Block
(IC694TBB032 or IC694TBS032). Cold
Junction Compensation are available
for Thermocouple configurations
(IC695ACC600 contains 2 CJCs)
Voltage: +50 mV, +150 mV, 0–5 V, 1–5 V,
0–10 V, +10 V; Current: 0–20 mA, 4–20 mA,
+20 mA; Thermocouple Inputs: B, C, E, J, K, N, R,
S, T; RTD Inputs: PT 385 / 3916, N 618 / 672, NiFe
518, CU 426: Resistance Inputs: 0 to 250 / 500 /
1000 / 2000 / 3000 / 4000 Ohms
Channel-to-Channel
Isolation
Number of Channels 16 Single Ended, 8 Differential 16 8
Single Ended: 5 ms for all channels
Update Rate
Resolution
Accuracy
Input Impedance
Input Filter Response
Notch Filter N/A N/A Yes
Diagnostics
Internal Power Used
External Power Requirement
Connector Type
Differential: 3 ms all channels
16 bit; ±10 V, 0.3125 mV, 1 LSB;
0-10 V, 0.3125 mV, 1 LSB
500K Ohms (single-ended mode)
1 MegaOhms (differential mode)
23 Hz (single-ended mode)
38 Hz (differential mode)
Under Range/Over Range,
Positive/Negative Rate of Change, High,
High-High, Low, Low-Low
112 mA (maximum) @ +5 VDC 120 mA @ +5 VDC 400 mA @ 5 V; 350 mA @ 3.3 V
110 mA (maximum) +24 VDC supply
connected to TB1 on IC695CHSxxx
Terminal Block (20 screws),
No No Two Groups of Four
6 ms all channels 10ms per Channel; 4 Channels = 40ms (1KHz
16 bit; 0-20 mA, 0.625 µA/bit;
4-20 mA, 0.5 µA/bit; 4-20 mA
Enhanced, 0.5 µA/bit
0.25% at 25ºC (77ºF) 0.25% at 25ºC (77ºF) Calibrated Accuracy at 25°C.
250 ohms Current 249 ohms ±1%
23 Hz Configurable: 8Hz, 12Hz, 16Hz,
Under Range/Over Range, Open Wire,
Positive/Negative Rate of Change, High,
High-High, Low, Low-Low
65 mA @ 24 VDC N/A
included with module.
Terminal Block (20 screws),
included with module.
filter) 127ms per Channel 4 Channels = 508ms
(8Hz filter) Channels that are disabled
are not scanned, shortening scan time.
11 to 16 bits, depending on configured
range and A/D filter frequency
Better than 0.1% of range (except
10 ohm CU RTD) Accuracy depends
on A/D filter, data format, input noise,
and ambient temperature.
40Hz, 200Hz, 1000Hz
Open Wire, Short Circuit,
Positive/Negative Rate of Change,
High, High-High, Low, Low-Low
IC694TBBx32 or IC694TBSx32.
Sold Separately.
www.geautomation.com
Automation & Control Systems
1.15
PACSystems RX3i Controller
Process Automation Control Systems
Analog I/O Modules (Input)
GE offers easy-to-use analog modules and HART analog modules for control processes such as
flow, temperature and pressure.
IC695ALG608 IC695ALG616 IC695ALG628
PACSystems RX3i Analog Input.
Configurable per channel for Current
or Voltage. High Density (8 Channel)
Product Name
Lifecycle Status Active Active Active
Module Type
Backplane Support Universal Backplane Only. Uses PCI Bus. Universal Backplane Only. Uses PCI Bus. Universal Backplane Only. Uses PCI Bus.
Number of Slots Module
Occupies on Backplane
Range
Requires High Density Terminal Block
(IC694TBB032 or IC694TBS032).
Analog Input Analog Input Analog Input with HART Communications
1 1 1
Current: 0 to 20 mA, 4 to 20 mA, ±20 mA;
Voltage: ±10 V, 0 to 10 V, ±5 V, 0 to 5 V, 1 to 5 V
PACSystems RX3i Analog Input.
Configurable per channel for Current
or Voltage. High Density (16 Channel)
Requires High Density Terminal Block
(IC694TBB032 or IC694TBS032).
Current: 0 to 20 mA, 4 to 20 mA, ±20 mA;
Voltage: ±10 V, 0 to 10 V, ±5 V, 0 to 5 V, 1 to 5 V
PACSystems RX3i Analog Input
with HART Communications.
Configurable per channel for Current
or Voltage. High Density (8 Channel)
Requires High Density Terminal Block
(IC694TBB032 or IC694TBS032).
Current: 0 to 20 mA, 4 to 20 mA, ±20 mA;
Voltage: ±10 V, 0 to 10 V, ±5 V, 0 to 5 V, 1 to 5 V
HART Support
Channel-to-Channel
Isolation
Number of Channels 8 16 8
All 8 Channels at 5 msec @ 500Hz.
Update Rate
Resolution
Accuracy
Input Impedance
Input Filter Response
Notch Filter Yes Yes Yes
Diagnostics
Internal Power Used
External Power Requirement
Connector Type
Performance is dependent on filtering.
32-bit IEEE floating point or 16-bit integer
(in 32-bit field) input data format
Calibrated Accuracy @ 13°C – 33°C with
8 Hz, 12 Hz and 16 Hz filter; 0 to 10 V,
±10 V input types: 10 mV0 to 5 V, 1 to 5 V,
±5 V input types: 5 mV0 to 20 mA,
4 to 20 mA, ±20 mA input types: 20 µA
Configurable: 8Hz, 12Hz, 16Hz,
Open wire, short circuit, positive/negative rate
of change, High, High-High, Low, Low-Low
450 mA @ 5 V; 600 mA @ 3.3 V 450 mA @ 5 V; 600 mA @ 3.3 V 450 mA @ 5 V; 600 mA @ 3.3 V
IC694TBBx32, IC694TBSx32 or IC694TBC032
N/A N/A Get HART Device Information (Function 1)
One Group of Eight One Group of Sixteen One Group of Eight
All 16 Channels at 9 msec @ 500Hz.
Performance is dependent on filtering.
32-bit IEEE floating point or 16-bit integer
(in 32-bit field) input data format
Calibrated Accuracy @ 13°C – 33°C with
8 Hz, 12 Hz and 16 Hz filter; 0 to 10 V,
±10 V input types: 10 mV0 to 5 V, 1 to 5 V,
±5 V input types: 5 mV0 to 20 mA,
4 to 20 mA, ±20 mA input types: 20 µA
Current 249 ohms ±1% Current 249 ohms ±1% Current 249 ohms ±1%
40Hz, 200Hz, 500Hz
N/A N/A N/A
Sold Separately.
Configurable: 8Hz, 12Hz, 16Hz,
40Hz, 200Hz, 500Hz
Open wire, short circuit, positive/negative rate
of change, High, High-High, Low, Low-Low
IC694TBBx32, IC694TBSx32 or IC694TBC032
Sold Separately.
Simplified HART Pass-Thru Command (Function 2)
Enterprise HART Pass-Thru Command (Function 3)
All 8 Channels at 5 msec @ 500Hz.
Performance is dependent on filtering
and HART enabled channels could add
6 to 8 seconds.
Selectable per channel
Calibrated Accuracy @ 13°C – 33°C
with 8 Hz, 12 Hz and 16 Hz filter;
0 to 10 V, ±10 V input types: 10 mV0 to
5 V, 1 to 5 V, ±5 V input types: 5 mV0 to 20 mA,
4 to 20 mA, ±20 mA input types: 20 µA
Configurable: 8Hz, 12Hz, 16Hz,
40Hz, 200Hz, 500Hz
Open wire, short circuit, positive/negative rate
of change, High, High-High, Low, Low-Low
IC694TBBx32 or IC694TBSx32.
Sold Separately.
Automation & Control Systems
1.16
www.geautomation.com
Process Automation Control Systems
PACSystems RX3i Controller
Analog I/O Modules (Input)
GE offers easy-to-use analog modules and HART analog modules for control processes such as
flow, temperature and pressure.
IC695ALG626 IC695ALG106 IC695ALG112
PACSystems RX3i Analog Input
with HART Communications.
Configurable per channel for Current
Product Name
Lifecycle Status Active Active Active
Module Type
Backplane Support Universal Backplane Only. Uses PCI Bus. Universal Backplane Only. Uses PCI Bus. Universal Backplane Only. Uses PCI Bus.
Number of Slots Module
Occupies on Backplane
Range
or Voltage. High Density (16 Channel)
Requires High Density Terminal Block
(IC694TBB032 or IC694TBS032).
Analog Input with HART Communications Analog Input with Channel
1 1 1
Current: 0 to 20 mA, 4 to 20 mA, ±20 mA;
Voltage: ±10 V, 0 to 10 V, ±5 V, 0 to 5 V, 1 to 5 V
PACSystems RX3i Isolated Analog Input
Configurable per channel for Current
or Voltage. High Density
(6 Isolated Channels)
Requires High Density Terminal Block
(IC694TBB032 or IC694TBS032).
to Channel Isolation
Current: 0 to 20 mA, 4 to 20 mA, ±20 mA;
Voltage: ±10 V, 0 to 10 V, ±5 V, 0 to 5 V, 1 to 5 V
PACSystems RX3i Isolated Analog Input.
Configurable per channel for Current or
Voltage. High Density (12 Isolated Channels)
Requires High Density Terminal Block
(IC694TBB032 or IC694TBS032).
Analog Input with Channel
to Channel Isolation
Current: 0 to 20 mA, 4 to 20 mA, ±20 mA;
Voltage: ±10 V, 0 to 10 V, ±5 V, 0 to 5 V, 1 to 5 V
HART Support
Channel-to-Channel
Isolation
Number of Channels 16 6 12
Update Rate
Resolution
Accuracy
Input Impedance
Input Filter Response
Notch Filter Yes N/A N/A
Diagnostics
Internal Power Used
External Power
Requirement
Connector Type
Get HART Device Information (Function 1)
Simplified HART Pass-Thru Command (Function 2)
Enterprise HART Pass-Thru Command (Function 3)
One Group of Sixteen Yes (250 VAC continuous, 1500 VAC for 1
All 16 Channels at 9 msec @ 500Hz.
Performance is dependent on filtering
and HART enabled channels could add
32-bit IEEE floating point or 16-bit integer
Calibrated Accuracy @ 13°C – 33°C with 8 Hz,
12 Hz and 16 Hz filter; 0 to 10 V, ±10 V input :
types 10 mV0 to 5 V, 1 to 5 V, ±5 V input
types: 5 mV0 to 20 mA, 4 to 20 mA, ±20 mA
Open wire, short circuit, positive/negative rate
of change, High, High-High, Low, Low-Low
6 to 8 seconds.
(in 32-bit field) input data format
input types: 20 µA
Current 249 ohms ±1% Current = 250 ohms ±1%,
Configurable: 8Hz, 12Hz, 16Hz,
40Hz, 200Hz, 500Hz
450 mA @ 5 V; 600 mA @ 3.3 V 400 mA @ 5 V; 600 mA @ 3.3 V 800 mA @ 5 V; 600 mA @ 3.3 V
N/A 19.2 V to 30 VDC, Current required: 500 mA 19.2 V to 30 VDC,
IC694TBBx32 or IC694TBSx32.
Sold Separately.
32-bit IEEE floating point or 16-bit integer
(in 32-bit field) input data format
±0.1% of span at 25°C, ±0.25%
of span over operating temperature range
Configurable low-pass: 8Hz, 12Hz, 16Hz,
40Hz, 250Hz, and 1000Hz
Open wire, under range, over range,
positive/negative rate of change, High,
High-High, Low, Low-Low
IC694TBBx32 or IC694TBSx32.
N/A N/A
minute per channel)
1 ms for all channels. 1 ms for all channels
Voltage >= 500k Ohms
Sold Separately.
Yes (250 VAC continuous, 1500 VAC
for 1 minute per channel)
32-bit IEEE floating point or 16-bit integer
(in 32-bit field) input data format
±0.1% of span at 25ºC, ±.25% of span
over operating temperature range
Current = 250 ohms ±1%,
Voltage >= 500k Ohms
Configurable: 8Hz, 12Hz, 16Hz,
40Hz, 250Hz, and 1000Hz
Open wire, under range, over range,
positive/negative rate of change,
High, High-High, Low, Low-Low
Current required: 500 mA
IC694TBBx32 or IC694TBSx32.
Sold Separately.
www.geautomation.com
Automation & Control Systems
1.17
PACSystems RX3i Controller
Process Automation Control Systems
Analog I/O Modules (Input)
GE offers easy-to-use analog modules and HART analog modules for control processes such as
flow, temperature and pressure.
IC694ALG220 IC694ALG221 IC694ALG222 IC694ALG223
PACSystems RX3i Analog Input,
Voltage, 4 Channel
Product Name
Lifecycle Status Active Active Active Active
Module Type
Backplane Support No Backplane Restrictions No Backplane Restrictions No Backplane Restrictions No Backplane Restrictions
Number of Slots Module
Occupies on Backplane
Analog Input Analog Input Analog Input Analog Input
1 1 1 1
-10 V to +10 V 4-20 mA, 0-20 mA -10 V to ±10 V, 0 to 10 V 0-20 mA, 4-20 mA
PACSystems RX3i
Analog Input, Current,
4 Channel
PACSystems RX3i
Analog Input,Voltage,
High Density (16 Channel)
PACSystems RX3i
Analog Input, Input,
Current, High Density
(16 Channel)
Range
HART Support
Channel-to-Channel
Isolation
Number of Channels 4 4 1 16
Update Rate
Resolution
±10 mV/40µA at 25ºC (77ºF) 0.1 % full scale 0.25% at 25ºC (77ºF) 0.25% at 25ºC (77ºF)
Accuracy
Input Impedance
Input Filter Response
Notch Filter N/A N/A N/A N/A
Diagnositics
N/A N/A N/A N/A
N/A N/A N/A N/A
4 ms all channels 2 ms all channels 13 ms all channels 13 ms all Channels
12 bit; 5 mV/20 µA/bit 12 bit; 0-20 mA, 5 µA/bit;
4-20 mA, 4 µA/bit
>9 Megohms 250 ohms 250 ohms 250 ohms
17 Hz 325 Hz 200 Hz 200 Hz
N/A N/A N/A N/A
12 bit; ±10 V, 5 mV/20 µA/bit;
0-10 V, 5 mV/20 µA/bit
12 bit; 0-20 mA, 5 µA/bit;
4-20 mA, 4 µA/bit; 4-20 mA
Enhanced, 5µA/bit
Internal Power Used
External Power
Requirement
Connector Type
Automation & Control Systems
1.18
27 mA @ 5 VDC; 98 mA @
24 VDC Isolated
N/A N/A N/A N/A
Terminal Block (20 screws),
included with module.
25 mA @ 5 VDC; 100 mA @
24 VDC Isolated
Terminal Block (20 screws),
included with module.
112 mA @ 5 VDC; 4150 mA- User
Supplied 24 VDC
Terminal Block (20 screws),
included with module.
120 mA @ 5 VDC; 65 mA-User
Supplied 24 VDC
Terminal Block (20 screws),
included with module.
www.geautomation.com
Loading...