GE ZTD910BF-SF-WF User Manual

Monogram.

“

ZTD910BF/SF/WF – GE Monogram 30" Warming Drawer

26"

Including Handle

23-1/4"

30"

10-1/2"

Drawer

Open

27"

1" Min. Above Toekick or Adjust to Oven Installation Height

28-1/2"

2" Min.

Allow 5/8" Overlap on All Sides

30"

10-1/2"

23-1/4"

23-1/2" Min.

Inside

Oven

Cutout

9-1/4"

2x2 or 2x4 Anti-Tip Block Against Rear Wall, 9" From Floor to Bottom of Block

28-1/2"

2" Min.

Allow 5/8" Overlap on All Sides

30"

10-1/2"

23-1/4"

23-1/2" Min.

Inside

1" Min. Above Toekick

Oven

Cutout

2x2 or 2x4 Anti-Tip Block Against Rear Wall, 9" From Floor to Bottom of Block

9-1/4"

2x4 or 2x2

Run ners or So lid Bottom

Install 2x4 or 2x2 Anti-Tip Block Against Rear Cabinet Wall 9" From Floor to Bottom of Block

Single Oven Installation (in inches)

Double Oven Installation (in inches)

Warming Drawer Dimensions (in inches)

Note: Additional clearance between cutouts may be required.

Check to be sure that oven supports above the Warming Drawer location do not obstruct the required interior 23-1/2" depth and 9-1/4" height.

Specification Revised 10/05

130716

Listed by Underwriters Laboratories

For answers to your Monogram,® GE Profile™ or GE appliance questions, visit our website at GEAppliances.com or call GE Answer Center® service, 800.626.2000.

Monogram.

“

ZTD910BF/SF/WF – GE Monogram 30" Warming Drawer

Electrical Outlet 16" Max. From Left Side

Installation Belo

a Dr

23-1/2 Min.

Solid Barrier

1/4

Air Gap

1-1/2 Cabinet Top

Countertop

Height

1 Min.*

28-1/2

9-1/4

Electrical Outlet 42" Max.

From Right Side

Install a Solid Barrier

Below a Cooktop

See Note

Electrical Outlet Flush With Side of Cabinet 7" Max.

Install 2x4 or 2x2 Anti-Tip Block Against Rear Cabinet Wall 9" From Floor to Bottom of Block

Install a Solid Barrier

and a 1/4" Air Gap

Above Warming Drawer

Min.

Side to Side Installation

Undercounter Installation (in inches)

Note: When installing warming drawer with a cooktop,

allow a 2" minimum from cooktop burner box bottom to top of cut-out.

Important Installation Note: Must provide anti-tip brace at the back of the cabinet and at the top of the cutout.

Optional Accessories: ZXD30B – 3/4" wood panel trim kit

* Note: When installing the warming drawer below a

cooktop, a solid barrier must be installed at 1" from the lowest point of the bottom of cooktop burner box to the top of cutout. Use any solid material such as 1/4" thick plywood. Allow at least 1/4" air gap between the barrier and the top of the warming drawer. See label on top of the warming drawer for approved cooktop models.

• When installed, the front face of the drawer will be nearly flush with adjacent cabinetry doors.

• Drawer overlaps will conceal cut edges on all sides of the opening.

The rough opening for the drawer must be:

–Depth 23-1/2" min. from inside back to front of cabinet frame. –Width 25-1/2" for 27" wide models, 28-1/2" for 30" wide models. –Height 9-1/4"

• 5" min. above floor or 1" above toekick. 23-1/4" from floor to bottom of cutout is recommended for under countertop installation.

Installation below a cooktop:

Warming drawers are approved for installation below only certain specified cooktop models. See the label attached to the top of the warming drawer for approved models. A solid barrier and air gap between cooktop and warming drawer is required. See Note above.

Installation below a cabinet drawer:

The warming drawer may be installed beneath a cabinet drawer. In this installation, a solid barrier should be installed above the warming drawer to block access. Use any solid material such as 1/4" thick plywood. Allow at least 1/4" air gap between the barrier and the top of the warming drawer. Observe the 5" min. above the floor or 1" above the toekick minimum installation height.

Note: If you are installing in frameless cabinets, it may be necessary to install 1/2" wide cleats to accept drawer mounting screws. See drawer to find exact locations of mounting screws.

Specification Revised 10/05

130716

Side to Side Installation:

Install two warming drawers in separate cutouts. Allow 2" min. between cutouts.

Listed by Underwriters Laboratories

For answers to your Monogram,® GE Profile™ or GE appliance questions, visit our website at GEAppliances.com or call GE Answer Center® service, 800.626.2000.

+ 1 hidden pages