GE ZISW420DM User Manual

Monogram.

™

ZISW420DM – GE Monogram 42" Built-In Refrigerator

with Dispenser and Water Filter

41-1/2

7"

5"

Electrical
Area

84 1/2" max

83 1/2" min

Finished
Opening

74" From Floor

to Bottom

of Electrical

24"

5"

5"

3 1/2"

Water Supply

3 1/2"

42" Models 18"

THE INSTALLATION SPACE

*84" From
Floor to
Top Frame

42"

Frame to Frame

41"

Case Width

*83-1/2"

at

Rear

*Shipping height.

The refrigerator
can be adjusted to fit
into a cutout that is
83-1/2” min. to
84-1/2” max. height.
Note that the top
case trim at the front
is 1/2” higher and
will overlap upper
cabinetry or soffit.
Use leveling legs
and wheels for
height adjustment.

Specification Revised 8/03

110176

19"

13"

23-7/8"
Behind
Frame

26-5/8"

130° Door Swing

90° Door Swing

Water And Electrical Locations

The opening must be prepared with the electrical and water
supply located as shown.

The cutout depth must be 24".

Designed for industry standard flush installation. The refrigerator
will project forward, slightly beyond adjacent cabinetry,
depending on your installation.

The cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot exceed
the 24" installation depth shown. The top case trim overlaps
the bottom of the soffit.

Frameless cabinets:

The case trim overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require filler strips to
prevent interference with cabinet door swing. The opening
must allow for filler strips.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.

• Water line can enter the opening through the floor or back wall.
The water line should be 1/4" O.D. copper tubing between
the cold water line and water connection location, long
enough to extend to the front of the refrigerator. Installation
of an easily accessible shut off valve in the water line
is recommended.

As an ENERGY STAR® Partner,

GE has determined that this product

meets the ENERGY STAR®

guidelines for energy efficiency.

Product Clearances

These refrigerators are equipped with a 2 position door stop.
The factory set 130° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.

Allow minimum clearances for freezer door and fresh food
door for a full 130° door swing and to allow for pan removal.

4" minimum clearance is required when door swing is adjusted
to 90°. If the 90° door stop position is used, pan access is
maintained, but pan removal is restricted.

For answers to your Monogram,® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.

R

Listed by
Underwriters
Laboratories

Monogram.

™

ZISW420DM – GE Monogram 42" Built-In Refrigerator

with Dispenser and Water Filter

1/4" FRAMED PANEL DIMENSIONS

If you choose to install framed panels, they must
be cut to the dimensions shown. The panels will
slide into the frame on the door and grille.

If the custom panel is less than 1/4" thick and it
fits loosely in the door frame it can be backed up
with a piece of filler material or foam tape to
improve the fit.

1/4"

Panel

Door

5/16"

Trim

Reveal

IMPORTANT NOTE: Maximum weight for fresh food panel is
50 pounds and 30 pounds for freezer panel.

IMPORTANT NOTE – Dispenser Models

The refrigerator is supplied with two dispenser trims,
one for framed panels and one for overlay panels.

• If the panel is less than 0.250" thick a noticeable gap
may be created around the dispenser trim. Foam
tape may be applied on the door to improve the fit.

• If the panel is more than 0.250" thick, the dispenser
trim cannot be secured to the door.

Fresh Food

Panel

Freezer

Panel

24-9/16

14-9/16

17-13/16

3-1/8

39-7/8

9-1/2

Grille Panel

68-3/8

Dispenser

Cutout

9-5/8"

Dispenser Cutout

15-3/8"

The framed panel
must be 1/4" nominal
thickness to fit the
dispenser trim.

SIDE PANELS

Side panels must be used whenever
the sides of the refrigerator will be
exposed. The 1/4" side panels will
slip into the side case trim. Order
the side panels from the cabinet
manufacturer.

* Depending on installation height.

*84"

2-9/16"

24"

*3" to 4"

As an ENERGY STAR® Partner,

GE has determined that this product

meets the ENERGY STAR®

guidelines for energy efficiency.

For answers to your Monogram,® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.

R

Listed by
Underwriters
Laboratories

Specification Revised 8/03

110176