Installation
Instructions
Side bg Side Refrigerators
Design Guide
With Installation Instructions
POObJ
02-08 JR
monogram,corn
7
Safety Information
BEFOREYOU BEGIN
Read these instructions completely and carefully.
•IN PORTANT- Savetheseinstructions
for local inspector's use. Observe all governing codes
and ordinances.
• Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions
with your Owner's Manual for future reference.
WARNING:
This appliance must be properly grounded.
See "Grounding the Refrigerator," page 10.
AVERTISSEMENT
Cet appareil dolt _tre correctement mis 6 la terre.
Consultez << Mise 6 la terre du r6frig6rateur >>,page 10.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
CAUTION:
Due to the weight and size of this refrigerator,
and to reduce the risk of personal injury or damage
to the product - THREE PEOPLE ARE REQUIRED
FOR PROPER INSTALLATION OF A 36" WIDE UNIT.
FOUR PEOPLE ARE REQUIRED FOR INSTALLATION
OF A 42" OR 48" WIDE MODEL.
PRUDENCE
_,cause du poids et de la taille de ce r6frig_rator
et pour r_duire le risque de blessure et de dommages,
IL FAUT TROIS PERSONNES POUR INSTALLER
CORRECTEHENT D'UN APPAREIL DE 91 cm (36 po}
DE LARGE. IL FAUT QUATRE PERSONNES POUR
L'INSTALLATION D'UN MODELE DE 107 OU 122 cm
(42 OU 48 po} DE LARGE.
Skill Level - Installation of this refrigerator requires
basic mechanical, carpentr 9 and plumbing skills.
Proper installation is the responsibilit 9 of the installer.
Product failure due to improper installation is not
covered under the GEAppliance Warranty.
See the Owner's Manual for warranty information.
WARNING:
• These refrigerators are tap-heavy and must
be secured to prevent the possibility of tipping
forward. Anti-Tip protection is required. See page 12
for details.
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service cords
that become frayed or damaged.
• Unplug the refrigerator before cleaning or making
repairs.
• Repairs should be made bg a qualified service
technician.
AVERTISSEMENT
• Ces r_frig6rateurs sont Iourds en haut et il faut les
arrimer pour _viter leur basculement. II faut avair
un sgst_me de protection contre le renversement.
Voir les d6tails page 12.
• II ne faut utiliser cet appareil qua pour I'utilisatian
appropri_e.
• R6parer ou remplacer imm6diatement tout cordon
61ectrique effiloch& ou endommag6.
• IIfaut d_brancher le r_frig&rateur avant le nettogage
ou toute intervention.
• Les r_parations doivent 6tre faites par un technician
qualifi&
For Monogram local service in your area,
call 1.800.444.1845.
ForMonogram serviceinCanada,
call1.800.561.:3344
ForMonogram Partsand Accessories,
call1.800.626.2002.
www, monogram.com
CONTENTS
Planning Guide
The Installation Space ......................................3
Dimensions and Clearances ..........................3
130°Door Swing ..................................................4
90° Door Swing ....................................................5
Customization Basics ........................................6
l/A" Framed Panel Dimensions ....................7
3/4" Overlay Panel Dimensions ....................8
Raised Overlay Panel Design ........................9
Side Panels ..........................................................10
Installation Instructions
Tools, Hardware, Materials ..........................10
Grounding the Refrigerator ........................10
Step 1, Remove Packaging ............................
Step 2, Hove Refrigerator into House ...11
Step 3, Install Water Line ......................11-12
Step 4, Household Water Filtration ........12
Step 5, Install Side Panels ............................12
Step 6, Install Anti-Tip Brackets ................12
Step 7, Level Refrigerator ............................13
Step 8, Alternate Anti-Tip Procedure _..13
Step 9, SecureRefrigerator to Cabinetry _14
Step 10, Adjust Door Swing ........................1/4
Step 11, Install Grille Panel ..........................14
Step 12, Install Framed Panels ..................15
2
Step 12A, Install Overlay Panels .__.16-17
Step 13, Install Dispenser Trim ..................18
Step 14,Connect Water Supply ................18
Step 15,Connect Power ..............................19
Step 16, Start Icemaker ................................19
Step 17, Install Toekick ..................................19
ZKHSS2Tubular Handle Kit
Step 1, Remove Door Handles ..................20
Step 2, Install Handles onto Panels ........21
Step 3, Install Assembled Handles ..........22
Step 4, Install Dispenser Trim ....................22
Design Guide
THE INSTALLATION SPACE
36"Models12"
42"Models18"
48"Models20"
_FiNshed Width
841/2" max
831/2" mhr
Finished
Opening
_24" f Electrical
31/2"
*Thefinishedcutoutwidth mustbe:
35-1/2"for 36"models
41q/2" for 42"models
4T1/2" for 48"models
Water And Electrical Locations
The opening must be prepared with the electrical
and the cold water supplg located as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightlg begond
adjacent cabinetrg, depending on gour installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. Thetop case
trim overlaps the bottom of the soffit.
75"FromFloor
toBottom
Area
f _
DIMENSIONS AND CLEARANCES
25-3/8"FramedModels
35",41", or47" adels
* Shippingheight.The
refrigeratorcanbe
adjustedtofit intoa
cutoutthat is 83-1/2"
min.to 84-1/2"max.
_84"From height.Notethatthe
"83-b
at
36",42"or48"
Frameto Frame
DepthIncludingHaedles:
26-7/8"FramedModels
27-3/4"StainlessSteelModels
28-11/16"ProfessionalModels
Product Clearances
These refrigerators are equipped with a 2-position door
stop. The factorg-set 130° door swing can be adjusted
to 90° if clearance to adjacent cabinets orwalls
is restricted.
130° DoorSwing
Floorto top casetrim atthe
TopFrame front is 1/2"higher
andwill overlap
uppercabinetryor
soffit. Useleveling
legsandwheelsfora
maxhnum1" height
adjustment.
90° DoorSwing
T
23-7/8"
Behind
I
Frame
J! 4-
..,._j.i!Lk,.
L_ J _
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supplg is
required. An individual properlg grounded branch
circuit or circuit breaker is recommended. Install
a properlg grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on the rear wall as shown.
NOTE:GFI(ground fault interrupter} is not
recommended.
• The water line can enter the opening through
the floor or back wall. The water line should be 1/4"
O.D.copper tubing or GESmartConnect TM kit between
the cold water line and water connection location,
long enough to extend to the front of the refrigerator.
Installation of an easilg accessible shut-off valve
in the water line is required.
Models A B C *Min. Distance
36" 13" 15" 20-5/8"
42" 13" 19" 26-5/8" q" Stainlessand
48" 15" 20" 28-5/8" TrimmedModels.
5" ProSeries
Allow minimum clearances for the freezer door
(Dimension A) and fresh food door (Dimension B)
for a full 150° door swing and to allow for pan removal.
For a 90° door swing, allow 4" min. clearance to a wall,
for framed and stainless steel models. Allow 5" min.
clearance for professional series models. If the 90° door
stop position is used, pan access is maintained, but pan
removal is restricted.
See the illustrations on pages 4 and 5to determine door
swing interaction with adjacent cabinets or countertops.
3
toWall
Refrigerator
\
Design Guide
Frameless Cabinets: The case trim overlaps
cabinets at the top and sides. Therefore,
frameless cabinets may require filler strips
23-7/8" From
Rearof
Refrigerator
\
to prevent interfeence with cabinet door
swing. The opening must allow for filler strips.
4
Refrigerator
Design Guide
CaseTrim
Frameless Cabinets:
The case trim overlaps
cabinets at the top
and sides.Therefore,
frameless cabinets mag
require filler strips to
prevent interference
with cabinet door swing.
The opening must allow
far filler strips.
23-7/8"
FromRearof
Refric_rator
1/4"
Top View
90 ° DOOR SWING
(optional setting)
Scale 1:1
IMPORTANTNOTE-
FOR DISPENSERMODELS:
Dispenser models are supplied
with two dispenser trims, one to fit
framed panels and one for overlag
panels. Dispenser trim fit to the
custom panel depends on correct
panel thickness. Framed panels
must be 1/4" nominal. Overlag
panels should be constructed as
shown to accomplish a total 1.100"
thickness. See pages 7 and 8 for
details.
• 1/2"
............
Doer
5
Design Guide
CUSTOMIZATION BASICS:
Framed Or Overlag Panels, Custom Handles and Accessorg Kits
Professional Style Stainless Steel Refrigerators
Stainless steel wrapped refrigerators have beveled edges
and professional-style handles. These models are shipped
ready for installation.
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refrigerators have wrapped doors
and grille panel, beveled edges, and tubular stainless steel
handles that coordinate with other Monogram appliances.
These models are shipped ready for installation.
Trimmed Refrigerators
Trimmed refrigerators are designed to be customized
with decorative panels. Field installed custom door
and grille panels are required.
Framed panels
You may install 1/4" thick custom panels from
gour cabinet manufacturer. The decorative panel slides
into the factory installed trim. Order black or stainless steel
accessory panels from gour Honogram dealer.
Overlag panels
You mag also choose to install custom overlag panels
from your cabinet manufacturer. This design provides
a seamless appearance which integrates smoothly with
surrounding cabinetrg.
StandardDoorHandles
Standardsuppliedhandlesshownin3/4" overlaypanelposition.
Door Handles
The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied bg gour cabinet maker
can also be installed on 3/4" overlag panels. If desired,
you mag order ZKHSS2Honogram stainless steel
tubular handle kit for 3/4" overlay panels.
FramedPanel
x/
StandardDoorHandles
Standardsuppliedhandlesshowoin1/4" panelposition.
Optional Accessorg Kits
ZKHSS2: Monogram Tubular Stainless Steel handles
designed to fit 3/4" overlay panels.
Accessorg Panels
Black and stainless steel accessory panels are available
from your Monogram dealer. Panels are cut to size and
readg to install.
Side Panels
Side panels must be used whenever the sides
of the refrigerator will be exposed.
ZISW480D ZPS480D
ZIS480N ZPB480N ZPS480N
ZISB420D ZPB420D ZPS420D
ZISW360D ZPS560D
ZIS360N ZPB560N ZPS360N
6
114" FRAMED PANEL DIMENSIONS
Design Guide
If gou choose to install framed panels, theg must
be cut to the dimensions shown. The panels will slide
into the frame on the door and grille.
Non-Dispenser Models
If the custom panel is less than 1/4" thick and it fits
Iooselg in the door frame it can be backed up with
a piece of filler material or foam tape to improve
the fit.
IMPORTANTNOTE- DISPENSERMODELS
The refrigerator issupplied with two dispenser trims,
one for framed panels and one for overla9 panels.
• If the panel is less than 0.250" thick, a noticeable gap
mag be created around the dispenser trim. Foam
tape ma9 be applied on the door to improve the fit.
Door
Reveal
.. 1/4"
Panel
\
x
_t
IMPORTANTNOTE:Maximumtotal panelweight:
• Freshfood doorpanel- 75 ibm
• Freezerdoorpanel- 53 Ibm
• GrillePanel- 18Ibs.
• If the panel is more than 0.250" thick, the dispenser
trim cannot be secured to the doon
See Dispenser Trim Fit Example, page 9.
_ Trim
GrillePanel
q
Dispenser F
Cutout J
Freezer FreshFood
Panel Panel
DispenserCutout
I_- 9-5/8"_1
8ide-bg-Side(in inches)
36" Hodels
42" Models
48" Hodeis
33-7/8 9 68-3/8 14-9/1618-9/16
39-7/8 9-1/2 68-3/8 14-9/1624-9/16
95-7/8 9-1/2 68-3/8 18-9/1626-9/16
Theframedpanelmustbe1/4"nominalthicknessto fit
thedispensertrim.
7
Design Guide
3/4" OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlag panels mag
be installed on trimmed models. The averlag panel must
be secured to a 1/4" thick backer panel which slides into
the trim. A spacer panel 0.10" thick must be placed
between the averlag and backer panel.
Assemble the panels with glue and screws:
• Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
• Center the spacer and backer panel on the overlag
panel and secure with glue and screws. Screws must
be countersunk into the backer panel.
IMPORTANTNOTE- DISPENSERMODELS
The refrigerator is supplied with two dispenser trims,
one far framed panels and one for overlag panels. The
overlag dispenser trim is designed to fit a total panel
thickness of 1.100".
• If the panel is lessthan 1.100" a noticeable gap mag
be created around the dispenser trim.
• If the panel is more than 1.100" the dispenser trim
cannot be secured to the door.
See Dispenser Trim Fit Example, page 9.
Door
1'/4"
Backer_
Panel LSpacer
.250" + .10" + .750" -- 1.100"TotalPaoelThickness
NOTE:Left4o-dghtoffset isnot
alwaysequalto top-to-bottom
offset.
• The overlag panel must be constructed according to
the specifications shown to achieve the correct total
thickness.
• Alternative panel construction methods such as
securing a 3/4" panel to a 1/4" backer panel cannot
be used. Another method, routing a 3/4" thick panel
on all sides, cannot be used. These methods will not
result in the required 1.100"panel thickness.
When a raised panel design is to be used, a custom
middle rail is required. See page 9 for details.
0veda
GrillePanel B
3ispenser F
Cutout J
Freezer FreshFood
Paoel Panel
i F
J
DJspenserCutout
*Cutthe dispenseropeningafter the backer,spacerandoverlag
panelshave beenassembled.
IMPORTANTNOTE:Haximum total weight for the assembled
panels:
• Fresh food door panel - 75 Ibs.
• Freezer door panel - 53 Ibs.
• Grille Panel- 18 Ibs.
36" Side-bg-Side (ininches)
c
i14" Backer Panel 33-718 9 68-318 14-9/16 18-9/16
.10" Spacer Panel 33 8-3/8 67 13-I/4 17-1/4
3/4"Overlay Panel 34-i/8 9-i/4 68-5/8 14-13/16 18-13/16
42" Side-b_-Side {in inches)
i/4" Backer Panel 39-7/8 9-i/2 68-3/8 14-9/16 24-9/16
.10" Spacer Panel 39 8-5/8 67 13-i/4 23-i/4
3/4"Overlay Panel 40-i/8 9-3/4 68-5/8 14-13/16 24-13/16
48" Side-b_-Side {in inches)
i/4" Backer Panel 45-7/8 9-i/2 68-3/8 18-9/16 26-9/16
.10" Spacer Panel 45 8-5/8 67 17-i/4 25-i/4
3/4"Overlay Panel 46-i/8 9-3/4 68-5/8 18-13/16 26-13/16
8
DISPENSER MODELS:
RAISED OVERLAY PANEL DESIGN
When a raised panel design isto be used,
a custom wide middle rail is required to accept
the dispenser trim.
• The middle rail must be wide enough to allow
for the dispenser trim to overlap the opening.
• The middle rail must be 1.100" total thickness
to accept the dispenser trim.
Design Guide
1/4"BackerPanel
.lO"Spacer
DISPENSER TRIM FIT EXAMPLES:
(NOT TO SCALE)
i/4" FRAMED PANEL
• The dispenser trim fits over the custom
panel and snaps into the freezer door.
• The clips will not engage the door
if the panel is more than 0.250" thick.
• If the panel is less than 0.250" thick,
a noticeable gap mag be created
around the dispenser trim.
I/4"
Framed
16-3/4"
dJ
10°5/8'L___.J
FREEZERDOOR
0.250"
Thick
t
I/4" Dispenser Trim
314" OVERLAY PANEL
• The dispenser trim fits over the custom
panel and snaps into the freezer door.
• The clips will not engage the door
if the panel is more than 1.100" thick.
• If the panel is less than 1.100" thick,
a noticeable gap mag be created
around the dispenser trim.
.lO"Spacer
9
FREEZERDOOR
1.100"
TotalThickness
3/4"Overlay Dispenser Trim
Design Guide
SIDE PANELS
Side panels must be used
whenever the sides of the
refrigerator will be exposed.
The 1/4" side panels will slip
into the side ease trim.
Secure the panels to the
refrigerator with stick-on
hook and loop fastener _84"
strips. Order the side
panels from the cabinet
manufacturer.
• Cut a notch in the top
front corner as shown
to allow clearance for _ _3"to4"
corner keys in the front _ 2-9/16"
side trim.
* Dependingon installationheight.
TOOLS AND MATERIALS REQUIRED
• Tinsnips to cut banding
• Stepladder
• 1" Bit extenion
• Tape measure
• Gloves
• 1/4" Drywall screws
• 5-Gal. Bucket with cover
• 6" Spirit level
• Appliance hand truck
• Tubing cutter
• 7/16" open-end wrench
• #2 Phillips screwdriver
• Drill and appropriate bits
• 5/16", 7/16" socket
• Safety glasses
• 1-1/8" open end wrench
• Pliers
• 1/4", 5/16" Combo Rachet
• 55" long 2x4 for Anti-Tip support
• 1/4" copper water line tubing or GESmartConnect TM
Refrigerator Tubing kits
• Water shut-off valve
• Custom panels for doors and grille panel
• Screws to secure refrigerator to cabinetrg
• Stick-on hook and loop fastener strips for
1/4" side panels
HARDWARE SUPPLIED
• Water filter bypass plug
• Anti-Tip brackets
• 1/4" nut and ferrule
• Dispenser trims for 2//4"and 5/4" overlag panels
(for use with Custom Panel models}.
• Aluminum cover trim for 3/4" overlag panels
with custom handles. Includes 22 flat head screws
and/4 endcaps.
FLOORING
For proper installation, this refrigerator must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should
be strong enough to support a fullg loaded refrigerator,
or approximately 1,500 Ibs.
NOTE:Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under
the refrigerator where you are working.
GROUNDING THE REFRIGERATOR
IMPORTANT- (Please read carefullg)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLYGROUNDED.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding} wall receptacle
to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
Where a standard 2-prong wall outlet isencountered,
it is your personal responsibility and obligation
to have it replaced with a properlg grounded
5-prong wall outlet.
DO NOT, UNDER
ANY CIRCUMSTANCES,
CUT OR REMOVE
THE THIRD (GROUND) PRONG
FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATORTO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
10
Installation Instructions
[STEP 11 REMOVE PACKAGING
CAUTION: The refrigerator is much heavier at
the top than at the bottom-be careful when moving.
When using a hand truck, handle from the side onlg.
PRUDENCE: Ler6frig_roteur estbeaucoup
plus Iourd en haut qu'en bas. IIfaut _tre prudent Iors
des d_placements. Si un diable est utilis6, il faut soulever
le r6frig&rateur sur le c6t6 seulement.
• Carefullg cut banding at the top and bottom,
remove the outer carton.
• Slide out the back corner posts (2).
• Slide the carton off the top of the cabinet.
NOTE:IT ISNOTNECESSARYTOLAYTHECABINETDOWN
IN ORDERTO REMOVETHESKID!
• The unit is secured to the skid with 4 slotted
tie-down straps. Remove the six 7/16" bolts
from the base channels in the tie-downs.
• The support blocks on the bottom of the refrigeration
case must be removed before the refrigerator is
taken off the skid or damage will occur. Carefullg
tilt the refrigerator and slide the blocks out from
beneath.
• Remove the toekick and set aside for final installation.
• Lift the refrigerator off the skid with an appliance
dallg. Handle from the sides.
[STEP21MOVE THE REFRIGERATOR INTO THE HOUSE
• Remove the six 7/16"
bolts securing the straps
to the skid.
CAUTION: DoNOT
ATTEMPTTO ROLL UNIT
OFFSKID.
Remove
TieDownsPRUDENCE: ,LNE
J FAUTPASESSAYERDEFAIRE
_ POURL'ENLEVERDELAY
ROULERLEREFRIGERATEUR
PALETTE.
• Re-use the corner posts from the packaging to protect stainless steel models. Runthe appliance dollg straps over
the posts and under the handles.
• Leave the protective film on the refrigerator until installation is complete.
IMPORTANT:Never lift the refrigerator bg the handle or push against the grill panel; this could cause damage
or misalignment.
• Avoid laging the unit on its back or side to prevent sealed sgstem restrictions.
[STEP 3] INSTALL WATER LINE
• A cold water supplg is required for automatic
icemaker operation. Thewater pressure must
be between 40 and 120 p.s.i.
• Route 1/4" ODcopper or GESmartConnect TM
plastic tubing between house cold water line
and the water connection location.
• The tubing should be long enough to extend
to the front of the refrigeraton Allow enough tubing
to accommodate the bend leading into the water line
connection.
NOTE:The onlg GEapproved plastic tubing issupplied
in the GESmartConnect TM Refrigerator Tubing kits.
Do not use ang other plastic water supplg line because
the line is under pressure at all times. Other tgpes
of plastic mag crack or rupture with age and cause
water damage to gour home.
GESmartConnect T"Refrigerator Tubing Kits are
available in the following lengths:
2' (.6m) WXO8X10002
6' (1.8 m) WXOSXIO006
15' (4.6m) WXOBX10015
25' (7.6m) WX08X10025
_Cold Water Line
11
Installation Instructions
[STEP 3] (continued)
Shut off the main water supplg.
Turn on the nearest faucet long enough to clear the line
of water.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easilg accessible.
• Turn on the main water supplg and flush debris.
Runabout a quart of water through the tubing into a
bucket. Shut off the water supplg at the shut-off valve.
NOTE:Saddle tgpe shut-off valves are included in mang
water supplg kits. Before purchasing, make sure a saddle
tgpe valve complies with gour local plumbing codes.
NOTE:Commonwealth of Massachusetts Plumbing I
Codes 248CHR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with gour licensed plumber.
ESTEP4] INSTALLATION WITH
HOUSEHOLD WATER
FILTRATION SYSTEM
Skip this step if SOUdo not have a household water
filtration sgstem
If the water supplg to the refrigerator isfrom
ang household water filtration sgstem, the filter
cartridge should be removed. Forbetter ice and water
performance, remove the filter and install the filter
bgpassplug.
I
ISTEP 6 ] INSTALLANTI-TIP BRACKETS
WARNING:ANT,-T,PPRECAUT,ONS
The refrigerator is top-heavy and must be secured
to prevent the possibilitg of tipping forward.
ATTENTION: PRECAUTIONS CONTRE
LES BASCULEMENTS
Lerefrig@rateur estbeaucouppluslourden haut
etilfautlemainteniren placepour@viterlapossibilit@
de son basculementversl'avant.
• Cuta 2"x4"block,35"longand securetheblock
tothemountingbracketsprovidedusing#12 or#14
wood screws.
2x4Cut_J_
35"Length
installation Mounting
Height
FrornFIoor
Screws Mounted intoj
VerdcalWall Studs
• Secure the bracket with wood block to the back wall
so that it is 84" (or gour installation height) from
the finished floor. Use #12 or #14 wood screws.
See the illustration.
BracketsBock.._
Required
Height
Bottom
ofWood
From
Floor
to
Block
Bracket
Brackets
NotRequired
Beneatha
Soffit
RotateClockwiseToRemove FilterBypassPlug
ESTEP5] INSTALL SIDE PANELS
Skip this step when not using side panels.
If Sou are using 1/4" side panels, theg should
be inserted into the case trim. Fasten the panels
to the refrigerator with stick-on hook and loop
fastener strips before setting the refrigerator in place.
SNeView
• The screws must penetrate at least one inch
into the vertical wall studs.
Connect power cord:
• Before pushing the refrigerator into the opening, plug
the power cord into the receptacle. Open the grille
panel and reach into the opening at the back to grasp
the power cord. Pull the power cord into the opening
as gou push the refrigerator back.
• Gentlg push refrigerator into the opening with hands
against front corners.
IMPORTANT NOTE:Whentherefrigerator is installedunderasoffit
or if there isnot enough height for this method of secuntg,brackets
cannot be used Proceedto step 7 to levelthe refrigerator and then to
step9to securerefrigeratorto cabinets Seestep 8 if gou have metal
wall studs Therefrigeratormustbesecuredto preventtipping
12
Installation Instructions
[STEP 71 LEVEL REFRIGERATOR
All models have 4-point leveling. The front is
supported b9 leveling legs, the rear issupported
b9adjustable wheels. Both are accessible from
the front of the refrigerator.
• To level the back of the refrigerator, turn the 7/16" hex
nut located above the front wheels. Turn clockwise
to raise or counterclockwise to lower the refrigerator.
• For front leveling, use a 1-1/4" open-end wrench.
• Adjust height of refrigerator to match installation
cutout opening 83-1/2" to 84-1/2". The refrigerator
should be level and plumb with cabinetrg.
[STEP 81ALTERNATE ANTI-TIP
PROCEDURE
The refrigerator must be secured to prevent tipping,
The anti-tip brackets cannot be used on metal
wall studs. Use this Alternate Procedure to secure
the refrigerator against tip-over whenever metal
wall studs are encountered and there is no soffit,
SideView
TopCaseTrim
i i
! !
InstallFour
1-1/2"DrywallScrews
ThroughTrimand IntoSoffit
or 3/4" Min.WoodBrace
CAUTION:
The rear leveling wheels and front leveling legs
are limited to a maximum height adjustment of 1".
If the installation requires more than 84-1/2" height,
the installer should elevate the refrigerator on a sheet
of plywood or runners. Cabinetrg trim could also
be added across the top of the opening to shorten
the opening. If gou attempt to raise the refrigerator
more than 1", gou will damage the front leveling
legs and the rear leveling wheels, Make adjustments
in small increments,
PRUDENCE
Les roues de nivellement arri_re et les pattes de
nivellement avant permettent un r_glage maximal
de 25 mm (1 po).8i I'ouverture pour le refrig6rateur
a une hauteur sup@ieure 6 2,15 m (84-1/2 po),
I'installateur dolt _lever le r_frig@ateur sur une feuille
de contre-plaqu_ ou des glissi&res. II est _galement
possible d'ajouter des baguettes de finition des
placards sur le haut de I'ouverture afin de la r_duire.
Lever le r_frig_rateur de plus de 25 mm (1pal
endommage les pattes de nivellement avant
et les roues de nivellement arri_re.
• Raisethe grille panel to access case tnm.
• Use a 3/16" bit to drill four evenlg spaced clearance
holes through the metal top case trim.
• Use a 1/16" bit to drill to pilot holes through the metal
clearance holes and into the wood soffit. The holes
should be centered in the soffit or a 3/4" rain. wood
brace. The brace spanning the enclosure must
be securelg fastened to cabinets on both sides.
• Install four, 1-1/2" drgwall screws into the pilot holes.
13
Installation Instructions
ESTEP9] SECURE REFRIGERATOR
TO CABINETRY
Whenever possible, perform this step for anti-tip
securitg, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
• Raise the grille panel to access the case trim.
• Drill a hole in the trim and drive a screw through
the trim into the adjacent cabinet.
• Follow the same procedure on the opposite side.
ThroughCaseTrimInto
AdjacentCabieets
ESTEP10] ADJUST DOOR SWING
ESTEP11] INSTALL GRILLE PANEL
(for Custom Panel Models onlg)
To insert the framed or overlag panel into the grille:
• Raise the grille panel to the stop position.
\
/
Loosen
Side Side
Trim Trim
Screw Screw
AdjustNutBelow
Springto Accommodate
PanelWeight
• Loosen the screws on the side trim behind the frame.
Remove the bottom trim.
NOTE:This refrigerator has a 2-position door stop.
When space does not allow the door to swing open
fullg to 130°, gou mac change the door swing to a 90°
opening. Skip this step if door opening is satisfactorg
for gour installation situation,
130°
letedor
Door
Hiege
• Open the door to view the bottom hinge.
Note the door stop pin locations. The pin isfactorg
installed in the 130° position.
• Close the door. From below, use pliers to unscrew
the door stop and reinstall into the 90° position.
CAUTION: The metal panel mac be
slipperg. Grip the metal panel firmlg so the panel
does not slip out of the frame and cause personal
injurg or damage to the frame.
PRUDENCE : Lepanneauen m&talpeut
b_tre glissant. Tenir fermement le panneau en m&tal,
de mani_re 6 ce que le panneau ne glisse pasen
dehors du cadre en provoquant des blessures
corporelles ou des dommages au cadre.
• Slide the panel over the metal backer panel and into
the trim.
• If necessarg, tap with awood block until the panel
slips under the top trim piece.
• Reassemble the bottom trim. Tighten the screws.
• Adjust the hinge spring to accommodate the panel
weight, if necessarg.
14
Installation Instructions
[STEP 12] INSTALL 114" FRAMED PANELS Go to Step 12A for Overlag Panels
Handle
Trim
SuppliedHandle
Shownin 1/4"
PanelPosition
p..
Install door panels:
• Open the door to 90°.Remove the 6 Phillips head screws
from the door handle.
• Remove the handle. Retain all screws.
• Remove the 6 screws holding the trim, then lift off
the trim. Retain the screws.
• Slide the framed panel into the door trim.
Refrigerator
Door
Dispenser Models Onlg:
• The dispenser controls protrude begond the face
of the freezer door. To avoid damage to the dispenser,
the trim at the top of the door should be removed.
• Remove the screws holding the top trim in place.
• Place the freezer panel into the bottom channel
and slide into the hinge side trim.
• Reinstall the top trim piece with screws.
• There are two sets of holes in the handle side trim.
Replace the handle side trim bg installing the original
screws in the FRONTscrew holes.
• Secure the handle to the door using the REARscrew
holes.
• Follow the same procedures to install the opposite panel.
• Check to be sure the handles are evenlg aligned with
each other at the top. To adjust, loosen the handle
screws and slide up or down. Tighten the screws.
NOTE:Aluminum cover trim is supplied for usewith
custom handles on overlay panels. It is not intended for
use with 1/4" panels. Discard the cover trim when using
1/4" framed panels.
UseFrontHoles
to SecureTrim
UseRearHoles
to SecureHandle
15
Installation Instructions
ISTEP 12AI INSTALL OVERLAY PANELS
b. .
D 46_
Install door panels:
• Open door to 90°. Remove the 6 Phillips head screws
from the door handle.
• Remove the handle. Retain all screws.
• Remove the 6 screws holding the trim, then lift off
the trim. Retain the screws.
• Slide the overlay panel into the door trim.
j DoorTrim
Haedle
Trim
Refrigerator
Door
Move
Forward
F0r3/4"
Panel
SuppliedHandle
Shownin Overlay
PanelPositioe
Dispenser Models Onlg:
• The dispenser controls protrude begond the face
of the freezer door. To avoid damage to the dispenser,
the trim at the top of the door should be removed.
• Remove the screws holding the top trim in place.
• Place the assembled freezer panel into the bottom
channel and slide into the hinge side trim.
• Reinstall the top trim piece with the screws.
• There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original screws
in the REARscrew holes.
• Secure the handle to the door using the FRONT
screw holes.
• Follow the same procedures to install the opposite panel.
• Check to be sure the handles are evenlg aligned with
each other at the top. To adjust, loosen the handle
screws and slide up or down. Tighten the screws.
J
UseFrontHoles
to SecureHandle
UseRearHoles
to SecureTrim
16
Installation Instructions
ISTEP12AI (continued)
Custom Handles
• If gou are using custom handles, the handle must
be praperlg secured to the overlag panel before sliding
the panel into the trim.
• The cabinet manufacturer will supplg the custom
handle and hardware.
• Discard the supplied handle.
Reinstallall originalscrews.
• Reinstall the handle side trim, using all 12 supplied
flat-head screws, plus the 12flat-head screws
originallg installed inthe handle trim.
• Install a supplied end cap onto the top of the door,
using a Phillips head screwdriver and the 2 screws
provided. Hand-tighten the screws into the end caps.
Do not overtighten; damage will occur.
• Clean the aluminum trim with rubbing alcohol-
do not use alcohols with oil or lanolin that will prevent
adhesion of double-sided tape.
• Slip the aluminum cover trim behind the top end cap
to check the fit. The aluminum cover trim has a recess
on each end which fits the end cap.
ISTEP12AI (continued)
• Carefully place the aluminum cover trim into top
end cap so that the recess is aligned with the cap.
Use the top to bottom grooves along the handle side
to align the cover trim accurately. Pull the tape a few
inches at a time while pressing the trim against
the doon Press and hold approximately 10 seconds
before continuing along the length of the doon
• Install another end cap at the bottom of the door
to secure the cover trim. Use a stubby Phillips head
screwdriver and the 2 screws provided.
NOTE: Make sure there are no gaps in the installation.
• Follow the same procedure on the opposite daan
CoverTrim TopEndCapFitsOver
InsertAluminum the AluminumTrim.
TrimIntoEndCap. SecureCapwith
2Screws.
• Remove the trim. Peel awag a few inches
of the adhesive backing.
IMPORTANT:The tape is very sticky and strong. Once
it adheres to a surface, it cannot be removed without
damaging both surfaces. Do not install the trim before
the final wood panels are in place. Besure to align
the trim carefully before removing the paper backing.
17
Installation Instructions
[STEP 13] INSTALL DISPENSER TRIM
Skip this step is gou are installing a stainless steel
wrapped or a non-dispenser refrigerator,
There are two dispenser trims shipped with gour
refrigerator. Select the appropriate trim for gour
application.
Compare the dispenser trims. Note that
the inside depth of the frames are different,
Choose the trim with less depth for framed
panels, choose the deeper one for overlag
panels.
Dispenser trim fit over the custom panel depends on
correct panel thickness. See pages 7 and 8 for panel
construction information.
ISTEP 14] CONNECT WATER SUPPLY
• Locate and bring the tubing to the front
of the cabinet.
• Turn the water on to flush debris from the line.
Runabout a quart of water through the tubing
into a bucket, then shut off the water.
Copper Tubing:
• Slip a 1/4" nut and ferrule (provided) over both ends of
the copper tubing. Insert the tube into the union fitting
on the unit and tighten the nut to the union.
• Turn on the water to check for leaks.
• Pressand snap the dispenser trim into the dispenser
recess on the refrigerator door.
If an excessive gap exists around the dispenser trim
or if the panel fits Ioosel9 in the door frame, foam tape
may be applied to help improve the fit. Remove
the trim and panel and applg the foam tape
to the door around the dispenser and in the corners.
GE SmartConnect T"Tubing:
• Insert the molded end of the tubing
into the refrigerator connection. Tighten
the compression nut until it isjust hand tight.
• Tighten one additional turn with a wrench.
Overtightening can cause leaks!
• Turn on the water to check far leaks.
NOTE: Hake sure excess tubing length does not
interfere with the toekick installation.
18
Installation Instructions
[STEP 15] CONNECT POWER, CLOSE
GRILLE PANEL
• Open the grill panel.
• Plug in the power cord (if necessarg) bg reaching
into the opening next to the water filter. If access is
too tight, remove the 2 screws holding the water
filter bracket and move aside. Plug in the power cord
and secure the bracket with the original screws.
\
MasterLight Electrical
Switches OutletAccess
• Check to make sure power to refrigerator is on
bg opening refrigerator door to see if interior lights
are on.
• The temperature controls are preset at 37°F for
the fresh food section and O°F for the freezer.
• Allow 24 hours to stabilize before making
adjustments.
[STEP 16] START ICEMAKER
[STEP 171 INSTALL TOEKICK
• Locate the supplied toekick (shipped taped to
the side of the refrigerator). Install with the 2 screws
provided, adjust to the desired height and tighten
the screws.
• A custom toekick can be installed to match
or complement the surrounding cabinetrg.
Use the supplied toekick as a template
to cut the shape.
SuppliedToekick
--]
%
1/4"orThickerToekick
INSPECT FINAL INSTALLATION
Check door alignment
Stand back awag from the refrigerator to inspect
the final installation.
• Check to be sure the handles are evenlg aligned with
each other at the top. To adjust, loosen the handle
screws and slide up or down. Tighten the screws.
• Shipping or the addition of heavg door panels
mag have caused the doors to move slightlg out
of alignment.
\
I
aker
/
Power
Switch
• Slide the switch to ON. The icemaker will begin
operation automaticallg.
• Be sure nothing interferes with the sweep
of the feeler arm.
• Discard the first full bucket of ice cubes.
• Toturn the icemaker off, slide the switch to OFF.
FeelerArm
"DoorOutof
Afignmeet
IL_J
• If necessarg, the fresh food door mag be adjusted up
or down to align with the freezer door.
• Use a 5/16" wrench to adjust the hinge pin as shown.
19
ZKHSS2 Tubular Stainless Steel Handles
This kit provides for the installation of Tubular Stainless Steel
handles an 3/4" averlag custom panels.
TOOLS AND MATERIALS REQUIRED
In addition to the custom door panels, gou need:
• #2 PNflipsscrewdriver • Ceeterpunch
• Drill and7/32"bit • Hammer
and7/8" spadebit
• Safetyglasses • Pencil
PARTS LIST
[STEP 1] REMOVE DOOR HANDLES
• Open the refrigerator door to 90 °. Remove
the 6 screws holding the handle to the door.
• Remove the 6 screws holding the handle side trim.
Retain all screws and trim. Discard the handle.
• Follow the same procedure to remove the freezer
handle and trim.
[
II L I1 _
8Handlestaedoffs 3/32"Allenwrenchforsetscrews
10Screwsfor handbstandoffs 10Plasticspacers(8required,2extral
#10-32x1"panheadmachhre
screws(8required,2 extra)
88888
10Setscrews(8 required,2extra)
20
ZKHSS2 Tubular Stainless Steel Handles
[STEP 2 ] INSTALL HANDLE ONTO PANELS
Drill Pilot Holes
• Measure, mark and draw a line, 1-1/8" from
the handle side edge, top to bottom.
• Hold the tubular handle against the appearance side,
centered top to bottom and on the marked line.
• Mark the screw hole locations at the center
of the handle attachment posts. Place the handle
over the marks to check again that the holes are
aligned to the handle posts.
• Center punch to mark the hole locations. Drill 7/32"
pilot holes from the appearance side and through
the entire panel thickness.
• Follow the same procedure to drill pilot holes
on the opposite door. !-1/8"
[STEP 2 ] (continued)
Secure Handles to Panels
• Use a 7/8" spade bit to drill 1/2" to 9/16" max. depth
into the back side of the panel. At this depth there
will be enough screw threads to engage the handle
on the appearance side.See the illustration below.
• Stand the panel up on the hinge side. Place a plastic
spacer into the 7/8" opening, then drop the screw
through the spacer.
1.100"
1/2" Min.
9/16" Max
7/32"
• Place the handle standoffs against the mounting
screws on the appearance side, then drive the top
screw partially into the standoff.
• Drive the next screw partially into the standoff.
Continue installing screws to the bottom location.
Alternate back to the top tightening screws one
at a time until the handle is tight against the panel.
Pa6_
CAUTION:H01elocationsmustbeexactto accept
handlestandoffandhandleassembly.
Assemble Handles
• Place a handle standoff on each attachment post on
the handle. Position the screw hole on the standoff to
point to the floon
• Install set screws into the bottom of each standoff,
using the Allen wrench provided. The standoff should
be tight against the handle.
AttachmentPest
screwinto panel
asshown.
Countersink
21
ZKHSS2 Tubular Stainless Steel Handles
[STEP 3] INSTALL ASSEMBLED HANDLES
• Slide the assembled panels into the door trim.
• Secure both trims using all the original screws.
Dispenser Models Onlg:
• The dispenser controls protrude begond the face of
the freezer door. To avoid damage to the dispenser,
the trim at the top of the door should be removed.
• Remove the screws holding the top trim in place.
Lift off the trim.
• Place the freezer panel into the bottom channel
and slide into the hinge side trim.
• Reinstall the top trim piece with screws.
iii@ii
[STEP 4] INSTALL DISPENSER TRIM
For Dispenser Models Onlg:
There are two dispenser trims shipped with your
dispenser refrigerator. Note that the inside depth
of the frames are different. Choose the trim marked
3/4" overlay panels.
• Press and snap the dispenser trim into the dispenser
recess on the door.
Reinstallalloriginalscrews
22
Notes
23
7
POOSJ
02-08 JR
Printed in the United States
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn
For Honogrom ® local service in gour area, call
1.800,444.1845
NOTE: Product improvement is a continuing endeavor at
General Electric Therefore, materials, appearance and
specifications are subject to change without notice
GE Consumer & Industrial
Appliances
General Electric Compang
Louisville, KY40225
ge,com
Loading...