Installation
Instructions
Side bySide Refrigerators
ZlS360N,ZlSB360D,ZlSW360D
ZlSS360N,ZlSS360D
ZIS420N,ZISB420D,ZISW420D
ZISS420N,ZISS420D
ZIS480N,ZISB480D,ZISW480D
ZISS480N,ZISS480D
Design 6uide
With Installation Instructions
Monogram:
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT- heseinstructionsfor
local inspector's liNe. Observe all governing codes and
ordinances.
• Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions with
your Owner's Manual for fuune reference.
WARNING:
This appliance must be properly grounded. See
"Grounding tile Refligeratoi;" page 10.
AVERTISSEMENT
Cet appareil doit &tre correctemellt mis _ la telre.
Consulter <<MiNe fi la terre du r_flig&ateur >,,page 10.
If you received a damaged refligerator, you should
immediately contact your dealer or buildeL
CAUTION:
Due to tile weight and size of tiffs refrigeratoi; and
to reduce tile risk of personal i_jm y or damage to
tile product - THREE PEOPI,E ARE REQ,UIRED
FOR PROPER INSTA1JATION OF A 36" WIDE
UNIT. FOUR PEOPI,E ARE REQUIRED FOR
INSTA1JATION OF A 42" OR 48" WIDE MODEl,.
PRUDENCE
]k cause du poids et de la taille de ce r_flig_rator et
pour r_duire le risque de blessure et de dommages,
II, FAUT TROIS PERSONNES POUR INSTAIJ,ER
CORRECTEMENT D'UN APPAREII, DE 91 cm (36 po)
DE lARGE. II, FAUT QUATRE PERSONNES POUR
I;INSTAIJATION D'UN MODt_I,E DE 107 OU 122 cm
(42 OU 48 po) DE lARGE.
Skill Level - Installation of tiffs refligerator
requires basic mechanical, carpent_ T and plumbing
skills. Proper installation is tile responsibility of the
insmlleL Product failure due to improper installation
is not covered under tile GE Appliance Warranty. See
tile Owner's Manual for warranty information.
WARNING:
• These refligerators are top-heax T and must
be secured to prevent the possibility of tipping
forward. Anti-Tip protection is required. See page
12 for derails.
• Use this appliance only for its intended purpose.
• hnmediately repair or replace elecuic service cords
that become frayed or damaged.
• Unplug tile refligerator before cleaning or making
repairs.
• Repairs should be made by a qualified service
teclmician.
AVERTISSEMENT
• Ces rdfligdrateurs sont lourds ell haut et il faut les
arrimer pour dviter leur basculement. I1 faut avoir
un syst_Ine de protection contre le renversement.
Voir les d_mils page 12.
• I1 ne faut ufiliser cet appareil que pour l'utilisadon
appropri_e.
• R_parer ou remplacer ilnm_diatement tout cordon
_lecuique effiloch_ ou endommag_.
• I1lCaut d_brancher le r_flig_rateur avant le
nettoyage ou toute intervention.
• I,es r_parations doivent &tre faites pal un
technicien qualifi_.
For Monogram local service in your area,
1-800-444-1845.
For Monogram service in Canada
1-888-880-3030
For Monogram Parts and Accessories, call
1-800-626-2002.
www. monogram.corn
CONTENTS
Planning Guide
The InstallationSpace ....................................3
Dimensions and Clearances ..........................3
130° DoorSwing ..............................................4
90° Door Swing ................................................5
Customization Basics ......................................6
1/4"Framed Panel Dimensions ......................7
3/4"Overlay Panel Dimensions ......................8
Raised Overlay PanelDesign ........................9
Side Panels......................................................10
Installation Instructions
Tools, Hardware, Materials ........................ 10
Grounding the Refrigerator .......................... 10
Step 1, Remove Packaging .......................... 11
Step 2, Install Water Line ............................ 11
Step 2A, RO Water Line ................................ 12
Step 3, Install Side Panels .......................... 12
Step 4, Install Anti-Tip Brackets ................ 12
Step 5, Level Refrigerator ............................ 13
Step 6, Secure Refrigerator to Cabinetry ..13
2
Step7, Adjust Door Swing ..........................13
Step 8,Install Grille Panel ............................14
Step 9,Install Framed Panels......................15
Step 9A, Install Overlay Panels ..................16
Step 10,Install Dispenser Trim....................17
Step 11,ConnectWater Supply ..................17
Step 12,ConnectPower ..............................18
Step 13,Start Icemaker ................................18
Step 14,Install Toekick ................................18
Design Guide
THE INSTALLATION SPACE
36"Models12"
42"Models18"
48"Models20"
/
_f
.... | Electrical _ 1
%//z"maxii ^ _ _,, i
831/2" min iI Area b i
Finished |I
Opening II 75"FromFloor
i 1/2'
*The finished cutout width must be:
35-1/2" for 36" models
41-1/2" for 42" models
47-1/2" for 48" models
Water And Electrical Locations
The opening must be prepared with the electrical
and water supply located as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Cutout depth beneath a soffit:
_qlen installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case
trim overlaps the bottom of the soffit.
*FinishedWidth
Ill to Bottom
Iq - 24" of Electrical
II Area
It 5"t WaterSupplY+5" 3 1/2"
DIMENSIONS AND CLEARANCES
25-3/8"FramedModels
25-3/4"StainlessSteelModels
35",41",or47" CaseDepth
i CaseWidth _..... _........_l * Shippingheight.The
i ..... refrigeratorcanbe
adjustedto fit into a
cutoutthat is 83-1/2"
rain.to 84-1/2"max.
•84"From height.Notethat the
Floorto top casetrim atthe
TopFrame front is 1/2"higher
andwill overlap
uppercabinetryor
soffit. Useleveling
legsandwheelsfor a
maximum1"height
adjustment.
.36",42",or 48"
Frameto Frame
DepthIncludingHandles:
25-7/8"FramedModels
27-3/4"StainlessSteelModels
Product Clearances
These refligerators are equipped with a 2 position
door stop. The factory set 130 ° door swing can be
adjusted to 90 ° if clearance to adjacent cabinets or
walls is resuicted.
130° DoorSwing 90° DoorSwing
'I'T
23_.7/8''
Behind
I c
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on rear wall as shown.
Note: GFI (ground fault interrupter) is not
recommended.
• _rater line can enter the opening through the
floor or back wall. The water line should be 1/4"
O.D. copper robing or GE SmartConnect TM kit
between the cold water line and water connection
location, long enough to extend to the front of the
refligerator. Installation of an easily accessible shut
off valve in the water line is required.
4" Min.
to Wall
Models A B C
36" 13" 15" 20-5/8"
42" 13" 19" 26-5/8"
48" 15" 20" 28-5/8"
Allow minimum clearances for fleezer door
(Dimension A) and fresh food door (Dimension B)
for a flail 130 ° door swing and to allow for pan
removal.
4" minimum clearance is required when door swing
is adjusted to 90°. If the 90 ° door stop position is
used, pan access is maintained, but pan removal is
restricted.
See illusuafions pages 4 and 5 to determine
door swing interaction with adjacent cabinets or
countertops.
3
Refrigerator
Design Guide
FramelessCabinets:The case trim
overlaps cabinets atthe top and sides.
Therefore, frameless cabinets may require
filler strips to )revent interfeence with cabinet
23-7/8"From
Rearof
Refrigerator
door swing. The opening must allow for filler
strips.
Case
Trim
1/4"
1/2"
" 2"
3/4"
1-1/4"
1-3/4"
1-1/2"
2-1/4"
i | q=
'-..... ....... , .... L...; .......... 1"
"',, (NominalSize)
2-3/4"
2-1/2"
3/4"Overlay
Panel
,
Top View
130 ° DOOR SWING
(factory setting)
Scale 1:1
IMPORTANTNOTE-
FORDISPENSERMODELS:
Dispenser models are supplied with two
dispenser trims, oneto fit framed panels
and onefor overlay panels. Dispensertrim
fitto thecustompaneldependson correct
panelthickness. Framedpanels must be
1/4"nominal. Overlay panels should be
constructed as shown to accomplish atotal
l.lO0"thickness. See pages 7 and 8 for details.
Door
4
Design Guide
Refrigerator
_--Case _im
FramelessCabinets:
The case trim overlaps
cabinets atthe top
and sides. Therefore,
frameless cabinets may
require filler strips to
prevent interference with
cabinet door swing. The
opening must allow for
filler strips.
234/8"
FromRearof
Refrigerator
Top View
90 ° DOOR SWING
(optional setting)
Scale 1:1
IMPORTANTNOTE-
FORDISPENSERMODELS:
Dispenser models are supplied
with two dispenser trims, one to fit
framed panels and one for overlay
panels. Dispensertrim fit tothe
custompaneldependson correct
panelthickness. Framedpanels
must be 1/4"nominal. Overlay panels
should be constructed asshown to
accomplish atotal 1.100"thickness.
See pages 7 and 8 for details.
......... 1-1/4"
1-1/2"
Door
3/4" Overlay
Panel
(NominalSize)
5
CUSTOMIZATION BASICS:
Design Guide
Framed Or Overlay Panels, Custom
Stainless Steel Wrapped Models
36" wide models - ZISS360N, ZISS360D
42" wide models - ZISS420N, ZISS420D
48" wide models - ZISS480N, ZISS480D
Trimmed Models
36" wide models - ZIS360N, ZISB360D, ZISW360D
42" wide models - ZIS420N, ZISB420D, ZISW420D
48" wide models - ZIS480N, ZISB480D, ZISW480D
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refrigerators have wrapped
doors and grille panel, beveled edges, and ulbular
stainless steel handles that coordinate with other
Monogram appliances. These models are shipped
ready for installation.
Trimmed Refrigerators
Trimmed refrigerators are designed to be customized
with decorative panels. Field installed custom door and
grille panels are required.
Framed panels
You may install 1/4" thick custom panels flom your
cabinet manufacturer. The decorative panel slides into
the factory installed trim. Or, order black, white and
stainless steel accessory panels flom your Monogram
dealer.
Handles and Accessory Kits
Overlay panels
You may also choose to install custom overlay panels
flom your cabinet manufacmreL This design provides
a seamless appearance which integrates smoothly with
surrounding cabineuy.
//¢/
_ !\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\i
3j40verayPane/JC
Standard supplied handles shown in 3/4"overlay panel position.
Door Handles
The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied by your cabinet maker
can also be installed on overlay panels. If desired, you
may order ZKHSS2 Monogram stainless steel tubular
handle kit for 3/4" overlay panels.
/ 2
1
StandardDoorHandles
FramedPanel _J
Standard supplied handles shown in 1/4" panel position.
Optional Accessory Kits
ZKHSS2: Monogram Tubular Stainless Steel handles
designed to fit,/4 overla) panels.
Accessory Panels
_qlite, black and stainless steel accessory panels are
available flom your Monogram dealeL Panels are cut to
size and ready to install.
3 " 7
StandardDoorHandles
Side Panels
Side panels must be used whenever the sides of the
refrigerator will be exposed.
ZISW480D ZPW480D ZPS480D
ZIS480N ZPW480N ZPB480N ZPS480N
ZISB420D ZPB420D ZPS420D
ZISW360D ZPW360D ZPS360D
ZIS360N ZPW360N ZPB360N ZPS360N
6
Design Guide
1/4" FRAMED PANEL DIMENSIONS
If you choose to install flamed panels, they must be
cut to the dimensions shown. The panels will slide
into the flame on the (loot and grille.
Non-Dispenser Models
If the custom panel is less than 1/4" thick and it fits
loosely in the door frame it can be backed tap with
a piece of fillet material or foam rope to improve
the fit.
IMPORTANT NOTE - Dispenser Models
The refligerator is supplied with two dispenser uims,
one for framed panels and one for overlay panels.
• If the panel is less than 0.250" thick a noticeable
gap may be created around the dispenser trim.
Foam rope may be applied on the door to improve
the fit.
t
t
t
, Door
t
t
t
t
|_5/16"
L Trim
Reveal
............1/4"
\\
\
\
\
I
\
\
\\
Panel
IMPORTANTNOTE:Maximum total panel weight:
• Fresh food door panel-75 Ibs.
• Freezer door panel - 53Ibs.
• Grille Panel- 18Ibs.
• If the panel is more than 0.250" thick, the
dispenser trim cannot be secured to the (loot.
See Dispenser Trim Fit Example, page 9.
A DispenserCutout
I GrillePanel i
-- 154/8"
7
F
Cutout
Dispenser _,
Side-by-Side(ininches)
Freezer FreshFood
Panel Panel
36"Models 33-7/8 9 68-3/8 14-9/16 18-9/16
M
42"Models 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
m
I_E_
48"Models 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16
Theframed panel must be 1/4"nominal thickness
to fit the dispenser trim.
7
Design Guide
3/4" OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may be
installed on trimmed models. The overlay panel must
be secured to a 1/4" thick backer panel which slides
into the uim. A spacer panel 0.10" thick must be
placed between the overlay and backer panel.
Assemble the panels with glue and screws.
• Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
• (]enter the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws must
be countersunk into the backer panel.
IMPORTANT NOTE - Dispenser Models
The refligerator is supplied with two dispenser trims,
one for flamed panels and one for overlay panels.
The overlay dispenser uim is designed to fit a total
panel thickness of 1.100".
• If the panel is less than 1.100" a noticeable gap may
be created around the dispenser uim.
• If the panel is more than 1.100" the dispenser trim
cannot be secured to the door.
See Dispenser Trim Fit Example, page 9.
Door
1/4"
Backer A
Panel _ _ Spacer
.250"+ .10" + .750" = 1.100"TotalPanelThickness
ROTE:Left-to-right offset
is not always equal to
top-to-bottom offset.
• The overlay panel must be consuucted according to
the specifications shown to achieve the correct total
thickness.
• Alternative panel construc6on methods such as
securing a 3/4" panel to a 1/4" backer panel cannot
be used. Another method, rou6ng a 3/4" thick
panel on all sides cannot be used. These methods
will not result in the required 1.100" panel thickness.
When a raised panel design is to be used, a custom
middle rail is required. See page 9 for details.
OverlayPanel
BackerPanel
GrillePanel
7
Dispenser
Cutout
Freezer FreshFood
Panel Panel
m
_D_ I_E_
F
DispenserCutout *Cut the dispenser opening after the backer, spacer and overlay
5!3 panels have been assembled.
IMPORTANTNOTE:Maximum total weight for the assembled
/8 panels:
• Freezer door panel- 53Ibs.
• Fresh food door panel- 75Ibs.
• Grille Panel- 18Ibs.
I" 94/8" _1
36"Side-by-Side(in inches)
1/4"BackerPanel 33-7/8 9 68-3/8 14-9/16 18-9/16
.10"SpacerPanel 33 8-3/8 67 13-1/4 17-1/4
3/4"OverlayPanel 34-1/8 9-1/4 68-5/8 14-13/16 18-13/16
42"Side-by-Side(in inches)
1/4"BackerPanel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
.10"SpacerPanel 39 8-5/8 67 13-1/4 23-1/4
3/4"OverlayPanel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16
48"Side-by-Side(in inches)
1/4"BackerPanel 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16
.10"SpacerPanel 45 8-5/8 67 17-1/4 25-1/4
3/4"OverlayPanel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16
8
Design Guide
DISPENSER MODELS:
RAISED OVERLAY PANEL DESIGN
When a raised panel design is to be used, a
custom wide middle rail is required to accept
the dispenser trim.
• The middle rail must be wide enough to allow
for the dispenser uim to overlap the opening.
• The middle rail must be 1.100" total thickness
to accept the dispenser trim.
1/4"BackerPanel
.10"Spacer
3/4"Overlay
Wide
Middle
16-3/4"
1
DISPENSER TRIM FIT EXAMPLES:
(NOT TO SCALE)
1/4" FRAMED PANEL
• The dispenser trim fits over the
custom panel and snaps into the
fleezer door.
• The clips will not engage the door if
the panel is more than 0.250" thick.
• If the panel is less than 0.250" thick, a
noticeable gap may be created
around the dispenser uim.
3/4" OVERLAY PANEL
• The dispenser uim fits over the
custom panel and snaps into the
freezer door.
• The clips will not engage the door if
the panel is more than 1.100" thick.
• If the panel is less than 1.100" thick, a
noticeable gap may be created
around the dispenser uim.
1/4"
Framed
1/4"Backer Panel
.lO"Spacer
Panel
FREEZERDOOR
0.250"
Thick
1/4"Dispenser Trim
FREEZERDOOR
1.100"
TotalThickness
3/4"Overlay Dispenser Trim
9
Design Guide
SIDE PANELS
Side panels must be used
whenever the sides of the
refligerator will be
exposed. The 1/4" side
panels will slip into the
side case trim. Secure the
panels to the refligerator
with s0ck-on hook and
loop fastener strips. Order
the side panels flom the
cabinet manufactureL
• Cut a notch in the top
fFoIlt coIIleI as showIl
to allow clearance for
corner keys in the flont
side trim.
*84"
,_ q_*3" to 4"
11
2-9/16"
* Dependingon installation
height,
TOOLS REQUIRED
• Tinsnips to cut banding
• Stepladder
• Bucket
• l,evel
• Appliance Hand Truck
• Tubing cutter
• 7/116" open-end wrench
• #2 Phillips screwdriver
• Drill and appropriate bits
• 5/16", 7/16" socket
• Safety glasses
• 1-1/4" open end wrench
• Pliers
• 1/4" ratchet wrench
HARDWARE SUPPLIED
• Water filter bypass plug
• And-Tip brackets
• 1/4" nut and ferrule
• Dispenser uims for 1/4" and 3/4" overl W panels
• 12 pan head screws for custom handle installation
MATERIALS REQUIRED
• 35" long 2x4 for Anti-Tip support
• 1/4" copper water line robing or GE
SmartConnect TM Refligerator Tubing kits
• Water shut-off vane (optional but recommended)
• Custom panels for doors and grille panel
• Screws to secure refligerator to cabinetry
• S0ck-on hook and loop fastener strips for
1/4" side panels
FLOORING
For proper installation, tiffs refligerator must be
placed on a level surface of hard material that is
at tim same height as tim rest of tim flooring. This
surface should be suong enough to support a fidly
loaded refligeratoI, or approximately 1,500 lbs.
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under the
refligerator where you are working.
GROUNDING THE REFRIGERATOR
IMPORTANT - (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERIX GROUNDED.
The power cord of tiffs appliance is equipped with
a three-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle to
minimize the possibility of elecuic shock hazard
flom this appliance.
Have tim wall oudet and circuit checked by a
qualified elecuician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall oudet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong
wall outlet.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG
FROM THE POWER CORD.
DO NOT USE AN ADAPTER PI,UG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTI,ET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPI fiANCE.
10
Installation Instructions
[STEP 11 REMOVE PACKAGING
CAUTION:Refrigerator is much heavier at the
top than at tile bottom - be careful when moving.
When using a hand truck, handle flom side onl>
PRUDENCE:I_er_frig&ateur est beaucoup
plus lourd en haut qu'en bas. I1 faut &tre prudent lots
des d_placements. Si un diable est utilis_, il faut
soulever le r_flig_rateur sur le c6t_ setdement.
• Carefully cut banding at tile top and bottom,
relilove triter carton.
• Slide out back corner posts (2).
• Slide carton off" top of cabinet.
NOTE: IT IS NOT NECESSARY TO I,AY CABINET
DOX_qN IN ORDER TO REMOVE SKID!
• Tile unit is secured to tile skid with 4 slotted
de-down suaps. Remove tile four 5/16" bolts flom
tile base channels ill tile tie-downs.
STEP 2 INSTALL WATER LINE
• Remove tile four 7/16"
bolts securing tile sUaps
to tile skid.
CAUTION:DoNOT
ATTEMPT TO ROI,I,
UNIT OFF SKID.
Remove
TieDowns
J
q
• Support blocks on tile bottom of tile refligerafion
case nlust be removed before tile refligerator is
token off the skid or damage will OCCUL Carefully,
tilt refligerator and slide blocks out flom beneath.
• Remove toekick, set aside for final installation.
• I,ift tile refligerator off tile skid with an appliance
doll},. Handle fiom tile sides.
,d
PRUDENCE:ii,NE
FAUT PAS ESSAYER DE
FAIRE ROUI,ER I,E
REFRIGERATEUR POUR
I/ENLEVER DE LAY
PAI_ETTE.
• A cold water supply is required for automatic
icemaker operation. Tile water pressure must be
between 40 and 120 p.s.i.
• Route 1/4" OD copper or GE SmartConnecff M
plastic robing between house cold water lille and tile
water connection location.
• Tubing should be long enough to extend to tile
flont of tile refligerator. Allow enough tubing to
accommodate bend leading into tile water lille
COIlllectioIl.
NOTE: Tile only GE approved plastic robing is
supplied ill tile GE SmartConnect TM Refligerator
Tubing kits. Do not use any other plastic water supply
lille because tile lille is under pressure at all times.
Other types of plastic m W crack or rupture with age
and cause water damage to your home.
GE SmartConnecff MRefligerator Tubing Kits are
available ill tile following lengths:
2' (.6 m) _9(08X10002
6' (1.8 m) _08X10006
15' (4.6 m) _9408X10015
25' (7.6 m) _08X10025
Shut off the main water supply.
Turn on tile nearest faucet long enough to clear tile
lille of water.
• Install a strut-off valve between tile icemaker water
vane and cold water pipe ill a basement or cabinet.
Tile shut-off valve should be located where it will be
easily accessible.
CopperTubing_'
SaddleType
CompressionNut
Shuto_ve_
Packin_
Outlet Valve
Ferrule
/
/
/
/
//////
/
/
\
(Sleeve)
NOTE: It is best to install tile valve into a vertical
water pipe. If you install tile valve into a horizontal
water pipe, make tile connection at tile top or
side, to avoid drawing off"any sediment flom tile
water pipe.
• Drill a 1/4" hole ill tile water pipe.
• Fasten tile strut-off vane to tile pipe with pipe
clamp.
• Tighten tile clamp screws until tile sealing washer
begins to swell. Do not over tighten.
• Place a compression nut and ferrule (sleeve) onto
tile end of tile tubing and connect it to tile strut-off
valve. Make sure tile tubing is fldly inserted into
tile valve and ferrule is tightened.
11
Installation Instructions
STEP 2 (continued)
• Turn on the main water supply and flush debris.
Run about a quart of water through the robing into
a bucket. Shut off water supply at the shuboff vane.
NOTE: Saddle type shut-off valves are included in
many water supply kits. Before purchasing, make
sure a saddle type vane complies with your local
plumbing codes.
NOTE: Commonwealth of Massaclmsetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massaclmsetts.
Consult with your licensed plumbex.
[STEP 2A WATER LINE
INSTALLATION WITH A REVERSE
OSMOSIS SYSTEM
Skip this step when not using an RO System
If the water supply to the refiigerator is fiom a
Reverse Osmosis Water System use the refiigerator's
filter bypass plug. Using the refligerator's water
filuafion camidge with the RO filter can result
in hollow ice cubes.
STEP 4 INSTALL ANTI-TIP BRACKETS
WARNING:ANT,-T,PPRECAUT,ONS
The refiigerator is top-heax T and must be secured to
prevent the possibility of tipping forward.
ATTENTION:PRECAUTIONS CONTRE LES
BASCULEMENTS
I,e r_frig_rateur est beaucoup plus lourd en haut et il
faut le maintenir en place pour &qter la possibilit_ de
son basculement vers l'avant.
• Cut a 2" x 4" block, 35" long and secure the block to
the mounting brackets provided using #12 or #14
wood scxews.
2x4Cut ,_
35"Lengthi '_ '_
--,,¥ _¥
Installation Mounting "---_-
Height Bracket
FromFloor
ScrewsMountedinto J
VerticalWall Studs
• Secure the bracket with wood block to the back wall
so that it is 84" (or your installation height) flom
the finished floox. Use #112or #114wood screws.
See illustration.
Clockwise_b
STEP 3 INSTALL SIDE PANELS
Skip this step when not using side panels
If you are using 1/4" side panels, they should be
inserted into tim case trim. Fasten the panels to the
refligerator with s0ck-on hook and loop fastener
suips before setting refligerator in place.
Brackets
Required
SideView
• Screws must peneuate at least one inch into vertical
wall studs.
• Before pushing the refrigerator into the opening,
plug the power cord into the receptacle. Open the
grille panel and reach into the opening at the back
to grasp the power cord. Pull the power cord into
the opening as you push the refrigerator back.
• Gently push refrigerator into the opening with
hands against flont corners.
ImportantNote:Whenthe refrigeratoris installedundera soffit or if
there isnot enoughheightfor this methodof security,bracketscannot
be used.Proceedto step5 to levelthe refrigeratorandthento step 6
to securerefrigeratorto cabinets.Therefrigeratormustbesecuredto
preventtipping.
m
Brackets
NotRequired
Beneatha
Soffit
12
Installation Instructions
STEP 5 LEVEL REFRIGERATOR
All models have 4-point leveling. The fiont is
supported by leveling legs, the rear is supported by
adjustable wheels. Both are accessible flom the flont
of the refligerator.
• To level the back of the refligerato_; turn the
7/16" hex nut located above the flont wheels. Turn
clockwise to raise or counterclockwise to lower the
refligerator.
• For flont leveling, use a 1-1/4" open-end wrench.
• Adjust height of refligerator to match installation
cutout opening 83-1/2" to 84-1/2". The refligerator
should be level and plumb with cabineuy.
HexNutAd
RearWheels j_Leveling Leg
STEP 6 SECURE REFRIGERATOR
TO CABINETRY
X4rhenever possible, perform this step for anti-tip
securiD_, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
• Raise the grille panel to access case uim.
• Drill hole in trim and drive screw through the trim
into adjacent cabinet.
• Follow the same procedure on the opposite side.
A
to Stop Position II / 1_11_
ThroughCaseTrimInto
AdjacentCabinets
CAUTION:
The rear leveling wheels and flont leveling legs are
limited to a maximum height adjustment of 1". If the
installation requires more than 84-1/2" height, the
installer should elevate the refligerator on a sheet
of pl)_,vood or rtmners. Cabineuy uim could also be
added across the top of the opening to shorten the
opening. If you attempt to raise the refrigerator
more than 1", you will damage the front leveling
legs and the rear leveling wheels.
PRUDENCE
I,es roues de nivellement arri&re et les pattes de
nivellement avant permettent un r_glage maximal
de 25 mm (1 po). Si l'ouverture pour le r_flig_rateur
a une hauteur sup_rieure _'t2,15 m (84-1/2 po),
l'installateur dolt _lever le r_flig_rateur sur une
feuille de conue-plaqu_ ou des glissib.res. I1 est
_galement possible d'_{iouter des baguettes de
finidon des placards sur le haut de l'ouvermre afin
de la rdduire. Lever le r6frig6rateur de plus de 25
mm (1 po) endommage les pattes de nivellement
avant et les roues de nivellement arri6re.
STEP 7 ADJUST DOOR SWING
NOTE: This refligerator has a 2-position door stop.
_qlen space does not allow the door to swing open
flHly to 130 °, you may change the door swing to a 90°
opening. Skip this step if door opening is satisfactory
for your installation situation.
130°
Interior'_
Door
Hinge
• Open the door to view the bottom hinge. Note the
door stop pin locations. The pin is facto_ T installed
in the 130 ° position.
• Close the dooL From below, use pliers to unscrew
the door stop and reinstall into the 90 ° position.
13
Installation Instructions
STEP 8 INSTALL GRILLE PANEL
To insert fiamed or overlay panel into the grille:
• Raise the grille panel to stop position.
Id" Lotqosen
Loosen
Side Side
Trim Trim
Screw Screw
AdjustNutBelow
Springto Accommodate
PanelWeight
• Loosen screws on side uim behind flame. Remove
bottom trim.
• Slide panel over the metal backer panel and into
the trim.
• If necessary, mp with a wood block until panel slips
under the top uim piece.
• Reassemble bottom trim. Tighten screws.
• Adjust the hinge spring to accommodate the panel
weight, if necessa_ T.
14
Installation Instructions
STEP 9 INSTALL FRAMED PANELS Goto Step9AforOverlayPanels
!,
Install door panels:
• Open door to 90 °. Remove the 6 Phillips head screws
flom the door handle.
• Remove handle. Retain all screws.
• Remove 6 screws holding uim, lift off uim. Retain
screws.
• Slide flamed panel into the door trim.
Dispenser Models Only:
• The dispenser controls protrude beyond the face of
the freezer door. To avoid damage to the dispense_,
the trim at the top of the door should be removed.
• Remove the screws holding the top trim in place.
• Place the fleezer panel into the bottom channel and
slide into the hinge side trim.
• Reinstall the top trim piece with screws.
J
/
Handle
Trim-_
Supplied
HandleShown
in 1/4"Panel
Position
DoorTrim
Refrigerator
Door
I_\\\\\\\\\\\\\\\\\\\\\1
,o :i:i:i:i:il
'i iiiiiiiiiii
• There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original
screws in the FRONT screw holes.
• Secure the handle to the door using the REAR screw
holes.
• Follow the same procedures to install the opposite
panel.
• Check to be sure handles are evenly aligned with each
other at the top. To adjust, loosen handle screws and
slide up or down. Tighten screws.
p -
--/ UseFrontHoles
_\ _/ to Secure Trim
" .........-.... "Use Rear Holes
to Secure Handle
15
Installation Instructions
[STEP 9A INSTALL OVERLAY PANELS
_" • hot
== {_0t
.iiii
I
Install door panels:
• Open door to 90 °. Remove the 6 Phillips head screws
flom the door handle.
• Remove handle. Retain all screws.
• Remove 6 screws holding uiln, lift off uiln. Retain
screws.
• Slide overl W panel into the door trim.
DoorTrim
Handle
Trim
Refrigerator
Door
Move
Forward
For3/4"
Panel
Supplied Handle
Shown in Overlay
Panel Position
Dispenser Models Only:
• The dispenser controls protrude beyond the face of
the fleezer door. To avoid damage to the dispenseL
the trim at the top of the door should be removed.
• Remove the screws holding the top trim in place.
• Place the assembled fleezer panel into the bottom
channel and slide into the hinge side uiln.
• Reinstall the top tHin piece with screws.
• There are two sets of holes in the handle side trim.
Replace handle side tHin by installing the original
screws in the REAR screw holes.
• Secure the handle to the door using the FRONT screw
holes.
• Follow the same procedures to install the opposite
panel.
• Check to be sure handles are evenly aligned with each
other at the top. To adjust, loosen handle screws and
slide lap or down. Tighten screws.
Custom handles
If you are using custom handles, the handle must be
property secured to the panel before sliding the panel
into the trim.
• The cabinet manufacturer will supply the custom
handle and hardware.
i,
' _ UseFrontHoles
/\\ /,
',, _ <_ to Secure Handle
• Secure the door Uilns using both the FRONT and
REAR screw holes. Use pan head screws to secure the
tHin. A package of 12 exua pan head screws can be
found in the literanne package. Discard supplied
handles.
............ UseRearHoles
toSecureTrim
16
Installation Instructions
STEP 10] INSTALL DISPENSER
TRIM
Skip this step is you are installing a stainless
steel wrapped or a non-dispenser refrigerator.
There are two dispenser trims shipped with your
refligeratoL Select the appropriate trim for your
applicad on.
Overlay
I Panel
I mm
Comparethe dispenser trims. Note that the inside
depth of the frames are different, Choosethe trim
with less depth for framed panels, choose the
deeper one for overlay panels.
STEP 11 CONNECT WATER SUPPLY
Check to be sure that refrigerator power cord is not
plugged into the wall outlet.
11
I
---.
,\ Refrigerator House
"-\.Water Supply Water Supply//
• I,ocate and bring tubing to the flont of the cabinet.
• Turn the water on to flush debris from line. Run
about a quart of water through robing into a bucket,
then shut-off wateL
Dispenser trim fit over the custom panel depends on
correct panel thickness. See pages 7 and 8 for panel
construction information.
• Press and snap the dispenser trim into the dis-
penser recess on the refrigerator dooL
If an excessive gap exists around the dispenser trim
or if the panel fits loosely in the door flame, foam
tape may be applied to help improve the fit. Remove
the trim and panel and apply foam tape to the door
around the dispenser and in the corners.
Copper Tubing:
• Slip a 1/4" nut and ferrule (provided) over both
ends of the copper tubing. Insert robe into the
union fitting on the unit and tighten nut to union.
• Turn on the water to check for leaks.
GE SmartConnect TM Tubing:
• Insert the molded end of the robing into the
refligerator connection. Tighten the compression
ntlt until it isjust hand tight.
• Tighten one additional turn with a wrench.
Overdghtening can cause leaks!
• Turn on the water to check for leaks.
Note: Make sure excess tubing length does not
interfere with toekick installation.
17
Installation Instructions
[STEP 12 CONNECT POWER
• Check to be sure the power cord is plugged into
tile receptacle.
L_
"\', Elec'trical
MasterLight Outlet
Switch
• Check to make sure power to refligerator is on by
opening refligerator door to see if interior lights
are oil.
• Tile temperature controls are preset at 37°F for tile
fresh food secOon and 0°F for tile freezeL
• Allow 24 hours to stabilize before making
adj tlsQIleIltS.
[STEP 13] START ICEMAKER
STEP 14 INSTALL TOEKICK
• I,ocate tile supplied toekick (shipped roped to
tile side of tile refligerator). Install with 2 screws
provided, adjust to desired height and tighten
scIews.
• A custom toekick can be installed to match or
complement tile surrounding cabinetry. Use tile
supplied toekick as a template to cut tile shape.
SuppliedToekick
[ t. _.t,
%
1/4"orThickerToekick
=====_. "%,
%
%
INSPECT FINAL INSTALLATION
Check door alignment
Stand back away flom tile refrigerator to inspect tile
final installation.
• Check to be sure handles are evenly aligned with
each other at tile top. To adjust, loosen handle
screws and slide up or down. Tighten screws.
• During shipping or tile addition of heaxT door
panels may have caused tile doors to move slightly
out of alignment.
• Flip tile switch to I (ON). Tile icemaker will begin
operation automatically.
• Be stlie nothing interferes with tile sweep of tile
feeler arm.
• Discard tile first fifll bucket of ice cubes.
• To turn tile icemaker off; set tile switch to O
(OFF).
"DoorOutof
Alignment
/
\
----q
/
\\
• If necessary, tile flesh food door may be adjusted
up or down to align with tile fleezer dooL
• Use a 5/16" wrench to adjust tile hinge pin as
S tl O_'V II.
18
Notes
19
_wbgNO._49-6013s-2
•No. 164D4373PO01t
10-03JR
25739-1
Note: While performing installations described in this book,
safety glasses or goggles should be worn•
For Monogram ® lo_wl s_r_ia_ in 3'o_ir (m_a, _wll
1-800-444-1845.
Note: Product improvement is a continuing endeavor at
General Electric. Thereli)re, materials, appearance and
specifications are sul)ject to change without notice.
Monogram:
GEConsumer Products
General Electric Company
Louisville, KY40225
©2003 General Electric Company
Loading...