GE ZIFS360NXRH User Manual
maintained but pan removal is restricted.
36" (91.5)
25 3/4" (65.45)
23 7/8" (60.7)
*84"
(213.4)
2 3/4"
(7.0)
*73 1/4"
(186.1)
*3 1/2"
(8.9)
*83 1/2"
(212.1)
64 1/4"
(163.2)
*6 1/2"
(16.5)
SIDE VIEWFRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
OVERALL DIMENSIONS
36" (91.5)
64 1/4"
(163.2)
*73 1/4"
(186.1)
*84"
(213.4)
ZIFS360NXRHGE Monogram® 36" Built-In All-Freezer
2 3/4"
(7.0)
25 3/4" (65.45)
23 7/8" (60.7)
*83 1/2"
(212.1)
SPECIFICATIONS
Overall Width 36" (91.4 cm)
Overall Height 84" (213.4 cm)
Overall Depth 25 3/4" (65.41 cm)
Door Clearance 36 3/4" (93.4 cm)
Cutout Width 35 1/2" (90.2 cm)
Cutout Height 83 1/2" - 84 1/2"
Cutout Depth 24" (61 cm)
(212.1 - 214.6 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 569 lb
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An inidividual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
*6 1/2"
(16.5)
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
35" (89.0)
Case width
** Allow 25" (63.5) min
clearance for 130˚
door swing
36 3/4"
(93.4)
TOP VIEW
*3 1/2"
(8.9)
SIDE VIEWFRONT VIEW
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
**These units are equipped with a 2-position door stop. The factory set 130° door swing can
be adjusted to 90° if clearance to adjacent cabinets or walls is restricted. Allow 15" minimum
clearance to wall for pan removal. If the 90˚ door stop position is used, pan access is
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimension may vary due to manufacturing tolerances.
Product Specification Created 3/14
SIDE VIEW
W
24" (61.0 )
2"
(5.1)
4"
(10.2)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
FRONT VIEW
ELEC.
35 1/2" (90.2)
2 5/16"
(5.9)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75
1/2
"
(191.8)
From floor
to bottom
of electrical
area
5 1/2"
(14.0)
9"
(22.9)
WITH ANTI-TIP BRACKET
5"
(12.7)
5"
(12.7)
WATER
3 1/2"
(9.0)
GE Monogram® 36" Built-In All-Freezer ZIFS360NXRH
STANDARD INSTALLATION
2 5/16"
(5.9)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
ANTI-TIP BRACKET
35 1/2" (90.2)
ELEC.
9"
(22.9)
5"
(12.7)
A
5 1/2"
(14.0)
WATER
3 1/2"
(9.0)
B
(12.7)
81 1/2"
(207.0)
5"
3 1/2"
75
1/2
(191.8)
From floor
to bottom
of electrical
area
(8.9)
locations at end
"
Use two
additional hole
of brackets
4"
(10.2)
holes selected
24" (61.0 )
2"
(5.1)
C
L
Screws
mounted
into vertical
wall studs
Make sure
are centered
on the studs
Wall
Studs
W
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
NOTES
A
Mounting the junction
box in this location will
also allow for front
accessability through
access panel.
B
Water supply area.
WARNING:
The freezer is top heavy
and must be secured to
prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the antitip system you must use
the product installation
instructions.
The information below
applies to all installation
constructions:
• A wall bracket, bolts and
toggles will be supplied
with the unit.
• The bolts will be used to
attach bracket to wall in
4 locations. Two of the
locations must penetrate
the center of the wall
studs.
• The toggles are used for
stability in drywall and
when metal studs are
encountered. Lag bolts
are used in wood studs.
• In installation opening,
measure 81 ½” from
floor and draw a
horizontal line.
• Locate and mark the wall
studs on horizontal line.
Verify at least two studs
have their centerlines
within the center 32.5”
of installation opening to
ensure 2 wall studs are
penetrated.
• The bracket will be
centered left to right in
opening with bottom of
bracket on the horizontal
line.
• When unit is placed in
opening, the bracket tabs
will align with openings
in back of the unit. The
unit will be secured to the
bracket using supplied
“L” bolts.
SIDE VIEW INSTALLED
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
See Installation
Instructions for detailed
instructions.
Product Specification Created 3/14
Loading...