Page 1
Monogram.
“
Monogram.
“
ZIF36NM – GE Monogram 36" Built-In All-Freezer
10-3/4" Max.
10" Min.
24-3/4"
35" Case
36" Overall
84-1/2" Max.
83-1/2" Min.
4"
73-1/2"
26-3/4"
R
36"
Frame to Frame
84*
26-1/4"
Including
Handle
35"
Case
Width
24-3/4"
Case
Depth
75" From Floor
to Bottom
of Electrical
Area
84-1/2" max
83-1/2" min
Finished
Opening
*Finished Width
Electrical
Area
5
5
3-1/2
24 3/4" Total
Depth
Water Supply
3-1/2
Wall View
2-1/2
5
6
75" From Floor
to Bottom
of Electrical
Area
84-1/2" max
83-1/2" min
Finished
Opening
*Finished Width
Electrical
Area
5
5
3-1/2
24 3/4" Total
Depth
Water Supply
3-1/2
Wall View
2-1/2
5
6
Enclosure Cutout and Product Dimensions (in inches)
ZIF36NMRH, Freezer
Handle on the left side, the door swings left to right.
ZIF36NMLH, Freezer
Handle on the right side, the door swings right to left.
Refrigerators are much heavier at the top than
at the bottom – be extra careful when moving.
Caution
• To achieve a flush fit, the finished cutout width must be
at least 36" wide.
• In a semi-flush installation, the finished cutout must
be 35-1/2".
• The electrical and water locations must be located as
shown for either type of installation.
*Shipped at 84" installation height. Can be adjusted to
83-1/2" or 84-1/2" with Grille Panel Kits.
Specification Revised 4/05
110156
*36" for a flush installation.
35-1/2" Min. for a semi-flush installation.
Note: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width. See installation examples.
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Page 2
Monogram.
“
Monogram.
“
ZIF36NM – GE Monogram 36" Built-In All-Freezer
23 9/16"
84"
2 9/16"
Trim
24 3/4"
84"
3 3/4"
R
1/4" Accessory Panels:
Factory trim accepts accessory panel kits. Panels are cut to size
and ready to install. Kits must be ordered separately.
White Black Stainless
Models Lexan® Lexan® Steel
ZIR36/ZIF36 ZWWR36 ZWBR36 ZWSR36
Door Handles – To match or complement cabinetry!
ZKHR1 – Provides the necessary framework to install a custom
handle of your choice, onto a 1/4" thick custom panel. (Handle
not included.)
ZKHTR1 – Provides the necessary framework to install a custom handle of your choice, onto a 3/4" thick custom panel.
(Handle not included.) This kit must be used in combination with
ZKTR36LH or ZKTR36RH.
ZKHRSS1 – Tubular stainless steel handle for 1/4" thick panel
installation.
ZKHTRSS1 – Tubular stainless steel handle for 3/4" thick panel
installation. This kit must be used in combination with ZKTR36LH
or ZKTR36RH.
• Side panels are required whenever the sides of the
product will be exposed and when installed between
frameless cabinets.
• Side panels are not required when installed into
an enclosure.
• Side panel installation will be determined by the design
of the side panel you have previously chosen.
• Side panels must be installed plumb.
Illustration A
1/4" Side Panels – Insert
end of side panel into case
trim. Fasten with hook and
loop strips.
Custom Panels – Match the cabinetry!
ZKTR36LH for ZIR36NMLH, ZIF36NMLH
ZKTR36RH for ZIR36NMRH, ZIF36NMRH
Provides for the installation of 3/4" thick custom door and grille
panels. Use this kit for a trimless appearance. This kit provides
a standard handle to fit the 3/4" panel.
Grille Panel – For Installation height adjustments!
ZGC2 – Provides 1/4" grille panel frame side pieces for 83-1/2"
and 84-1/2" installation heights. The supplied grille panel frame
is set for 84".
Side-by-Side Installation
ZUG75 Trim Kit – For side-by-side installation of two trimmed
units. This kit provides for the
installation of a unified 3/4" grille
panel to span the width of two
units. This kit contains a trim
strip to cover the inside case
trim for a finished appearance.
This kit must be used in
combination with BOTH the
ZKTR36LH and ZKTR36RH kits.
• If you choose to use 1/4" side panels, they should be inserted into
the case trim as illustrated. Fasten the panels to the product
with stick-on hook and loop fastener strips (not provided) before
setting in place. See illustration A.
• 1/2" to 3/4" side panels are normally set into place and fastened
to adjacent cabinetry or the back wall before rolling the product
into the opening. See illustration B.
Illustration B
1/2" to 3/4" Side Panels –
Leading edge of side panel
is flush with cabinet front.
Fasten to the back wall
using a cleat.
Top View
Standard 4" high toekick or trim to fit.
Height may vary depending on application.
Specification Revised 4/05
110156
Top View
Standard 4" high toekick or trim to fit.
Height may vary depending on application.
For answers to your Monogram,® GE Profile™ or
Listed by
Underwriters
Laboratories
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Page 3
Monogram.
“
Monogram.
“
ZIF36NM – GE Monogram 36" Built-In All-Freezer
37"
1/2" Thick
Side Panels
36"
Finished Dim.
Roughed-In Dim.
Cabinet
Refrigerator
Cabinet
Refrigerator Door
73"
1/2" Thick
Side Panels
72"
Finished Dim.
Rough-In Dim.
36"
84"
24-3/4"
36"
1/4" Thick
Side Panels
71 1/2"
Finished Dim.
72"
Rough-In Dim.
2 1/2"
75" From Floor
to Bottom
of Electrical
Area
84 1/2" max
83 1/2" min
Finished
Opening
*Finished Width
Electrical
5"
5"
3 1/2"
24 3/4" Total
Depth
Water Supply
Wall View
6"
5"
6"
28 1/2"
26"
Freezer Refrigerator
R
Installation at End of Run
Refrigerator and Freezer
installed side-by-side
Note: 1/2" thick side panels shown. Side
panels can be any thickness. Add side
panel thickness to outside trim width
(36" or 72" for two models) to calculate
the rough-in dimension. The leading
(front) edge must be finished to match
surrounding cabinetry.
Side-By-Side Installation of Freezer and Refrigerator
For a complete food storage center, install a Monogram
Freezer and Refrigerator side-by-side. For even more
capacity, install two refrigerators and/or two freezers.
• Order ZUG75 Unified Grille Panel Kit for one
• The electrical and water locations must be located
Specification Revised 4/05
110156
continuous 3/4" custom grille panel.
as shown for either type of installation. A separate
115V, 60Hz., 20 amp power supply is recommended
for each product.
*72" min. for a flush installation
71-1/2" min. for a semi-flush installation
Note: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width.
For answers to your Monogram,® GE Profile™ or
Listed by
Underwriters
Laboratories
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Page 4
Monogram.
“
Monogram.
“
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Custom
Panel
A
B
Rout for 3/4"
Handle Kits Only
See Details
1/4"
Max.
Appearance Side
For Handle Kits Only
Rout Back Side of Panel
1-13/16"
Width
Height
Custom Grille Panels
Width
Height
ZUG75 Grille Panel
R
Custom Panel Dimensions
IMPORTANT: Maximum
weight for custom door
panel is 67 pounds and
9 pounds for the grille
panel.
CUSTOM DOOR PANEL SIZES
SIZES A B
1/4" Panels 35-1/16" 68-7/8"
3/4" Panels 35-1/16" 68-15/16"
3/4" Panels
(custom handles) 35-1/4" 68-15/16"
Custom Grille Panel Dimensions
1/4" THICK CUSTOM GRILLE PANEL
Panel Panel Height
Width to Fit Installation Height
83-1/2" 84" 84-1/2"
35-1/8" 7-1/2" 8" 8-1/2"
Note: The grille panel frame is factory assembled
for 84" installation height. Order ZGC2 Grille Panel
Kit when installation height is more or less than 84".
3/4" THICK CUSTOM GRILLE PANEL
Requires ZKTR36 Trim Kit
Panel Panel Height
Width to Fit Installation Height
83-1/2" 84" 84-1/2"
35-1/4" 7-3/4" 8-1/4" 8-3/4"
Note: A grille panel support is included with the
ZKTR36 trim kit and fits all installation heights.
Routing Detail
Rout the panel when installing a ZKHTR1 Custom
Handle Kit or ZKHTRSS1, Tubular Stainless Steel
Handle Kit.
Specification Revised 4/05
110156
ZUG75 Grille Panel Dimensions
This Grille Panel Kit should be used in combination
with ZKTR36H and ZKTR36RH, 3/4" panel kits.
3/4" THICK CUSTOM GRILLE PANEL
Requires ZUG75 Trim Kit
Panel Panel Height
Width to Fit Installation Height
83-1/2" 84" 84-1/2"
71-3/8" 7-3/4" 8-1/4" 8-3/4"
For answers to your Monogram,® GE Profile™ or
Listed by
Underwriters
Laboratories
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Page 5
Monogram.
“
Monogram.
“
ZIF36NM – GE Monogram 36" Built-In All-Freezer
25"
Minimum
to Wall
130° Door Swing
36-3/4"
4" Min.
to Wall
90° Door Swing
25"
Min. to
Wall
0"
25"
Min. to
Wall
130
° Door Swing 130° Door Swing
R
Clearances
• Factory set for a 130° door swing. Order WX14X99
adjustable door stop to reduce swing to as little
as 90°.
When Installed into a corner:
Allow 25" for a full 130° door swing. Allow 15" for
pan removal. Allow 4" min. clearance when
door swing is adjusted to a 90° opening for pan
access, but pan removal is restricted.
When installing an All-Refrigerator and All-Freezer
side-by-side, allow 25" for a full 130° door swing,
or 15" min. on the hinge sides for pan access.
90° door swing with
optional WX14X99
door stop.
Specification Revised 4/05
110156
ZUG75 Unified Grille Panel Kit is available for side-by-side
installations. See Trim Kit descriptions.
For answers to your Monogram,® GE Profile™ or
Listed by
Underwriters
Laboratories
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Page 6
Monogram.
“
Monogram.
“
ZIF36NM – GE Monogram 36" Built-In All-Freezer
0"
3/4"
R
Design Information
Flush or Semi-Flush Enclosure Installation
True Flush Installation
True Flush Installation
In a flush installation,
the freezer doors
will align evenly
with the front face
of adjacent cabinet
doors. The freezer
blends into the
surrounding cabinetry.
Monogram built-in refrigerators and freezers can be
installed flush with typical 24-3/4" deep cabinetry.
When installed semi-flush, the case trim will conceal
slight gaps around the enclosure. The refrigerator
will project forward approximately 3/4" beyond the
front face of surrounding cabinetry.
Semi-Flush Installation
Semi-Flush Installation
These freezers can
also be installed
semi-flush into an
enclosure using the
minimum cutout width.
The case trim creates
a frame around
the opening.
Side Panel Requirements:
• Side panels are not required whenever the refrigerator or
freezer is installed into an enclosure or between pantry and
oven cabinets.
• Side panels are required whenever the sides of the product
are exposed.
• Side panel sizes vary depending on the type of installation being
made.
Specification Revised 4/05
110156
To accomplish an attractive installation, you must:
1. Determine the need for side panels.
2. Determine side panel thickness.
3. Order matching side panels from the cabinet manufacturer.
Be sure to provide the exact dimensions.
For answers to your Monogram,® GE Profile™ or
Listed by
Underwriters
Laboratories
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Page 7
Monogram.
“
Monogram.
“
ZIF36NM – GE Monogram 36" Built-In All-Freezer
ZIR36NDLH/ZIF36NDLH
Features and Benefits
• 21.9 Cu. Ft. Freezer Capacity
• Wire Freezer Shelves (5 Adjustable,
• Wire Baskets with Full-Extension Slides
• 2 Extra Large Wire Baskets with
• 8 Door Bins and Gallon Storage
• Automatic Defrost Sealed System Design
• Full Extension Slides
• Door Panels Required
• Model ZIF36NMRH – Door panels required
• Model ZIF36NMLH – Door panels required
1 Fixed, 1 Full-Width Fixed)
(2 Regular, 4 Large)
Easy Access Lid and Full Extension Slides
(right-handed door swing)
(left-handed door swing)
Specification Revised 4/05
110156
Loading...