GE ZIR36N RH, ZIF36N LH User Manual 2
GE Monogram
®
36" Refrigerators
and 36" Freezers
Custom
Options Guide
and
Installation
Instructions
With Custom Pas ifimenstions
CAUTION
Before you begin – Read these instructions completely and carefully.
IMPORTANT – Save these instructions for local inspector’s use.
IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
2
Contents
Design Information
Flush or Semi-Flush Enclosure Installations ....................3
Enclosure Cutout and Product Dimensions ......................3
Clearances ..............................................................................4
Side By Side Installation of Freezer
and Refrigerator ....................................................................4
Installation Examples ........................................................4, 5
Frameless Cabinets ..............................................................5
Accessory Panel Kits ............................................................5
Models Available ..................................................................6
Advance Planning Appearance Options ..........................6
Trim Kit Descriptions ............................................................6
Custom Panel Dimensions
Product and Cutout Information ..........................................7
1/4" Thick Custom Panels on 1/4" backing ........................8
3/4" Thick Panels with Supplied Handle ............................9
3/4" Thick Panels with Custom Handle ............................10
Side Panel or Filler Options ................................................11
Installation Instructions ................................................12-18
If you received a damaged product, you should
immediately contact your dealer or builder.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliance Warranty. See the
Owners’ Manual for warranty information.
For Monogram local service in your area,
1.800.444.1845.
For Monogram service in Canada,
1.888.880.3030
For Monogram Parts and Accessories, call
1.800.626.2002.
WARNING
• Il ne faut utiliser cet appareil que pour l’usage pour
lequel il a été construit.
• Il faut réparer ou remplacer immédiatement tout
cordon d’alimentation électrique effiloché ou
endommagé.
• Débrancher le réfrigérateur avant le nettoyage ou
toute intervention.
• Les réparations doivent être faites par un
technicien qualifié.
ATTENTION
Cet appareil doit être correctement mis à la terre.
Consulter « Mise à terre du réfrigérateur », page 12.
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service cords
that have become frayed or damaged.
• Unplug the refrigerator before cleaning or making
repairs.
• Repairs should be made by a qualified service
technician.
ATTENTION
This appliance must be properly grounded. See “Grounding the Refrigerator,”
page 12.
CAUTION
PRUDENCE
Due to the weight and size of this refrigerator, and
to reduce the risk of personal injury or damage to
the product – THREE PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
À cause du poids et de la taille de ce réfrigérator et
pour réduire le risque de blessure et de dommages,
IL FAUT TROIS PERSONNES POUR FAIRE
L’INSTALLATION CORRECTEMENT.
Trim Kits
ZGC2 Trim Kit, Grille Panel Frame Adjustment ..............19
ZKHR1 Trim Kit (for 1/4" Panels),
Support for Custom Handles ......................................20-21
ZKTR36LH/ZKTR36RH Trim Kit,
3/4" Custom Panels ......................................................22-25
ZKHTR1 Trim Kit (for 3/4" Panels),
Support for Custom Handles ......................................26-28
ZKHRSS1 Trim Kit (for 1/4" Panels),
Tubular Stainless Steel Handles ................................29-32
ZKHTRSS1 Trim Kit (for 3/4" Panels),
Tubular Stainless Steel Handles ................................33-34
ZUG75 Trim Kit, Unified 3/4" Grille Panel Kit ............ 35-40
CAUTION
WARNING
3
Design Information
36" Refrigerators, Freezers
Flush or Semi-Flush Enclosure Installations
Side Panel Requirements:
• Side panels are not required whenever the
refrigerator is installed into an enclosure or between
pantry and oven cabinets.
• Side panels are required whenever the sides of the
refrigerator are exposed.
• Side panel sizes vary depending on the type of
installation being made.
To accomplish an attractive installation, you must:
1. Determine the need for side panels.
2. Determine side panel thickness.
3. Order matching side panels from the cabinet
manufacturer. Be sure to provide the exact
dimensions.
True Flush Installation
In a flush installation,
the refrigerator doors
will align evenly with the front
face of adjacent cabinet doors.
The refrigerator blends into the
surrounding cabinetry.
Semi-Flush Installation
These refrigerators
can also be installed
semi-flush into an enclosure
using the minimum cutout
width. The case trim creates a
frame around the opening.
Monogram built-in refrigerators and freezers can be
installed flush with typical 24-3/4" deep cabinetry.
When installed semi-flush, the case trim will conceal
slight gaps around the enclosure. The refrigerator or
freezer will project forward approximately 3/4" beyond
the front face of surrounding cabinetry.
In any installation situation, a wide range of appearance
options can be accomplished through the use of one or
more trim kits. See trim kit descriptions and appearance
options on page 6.
Enclosure Cutout and Product Dimensions
• To achieve a flush fit the finished cutout width must be
at least 36" wide.
• A semi-flush installation requires 35-1/2" min. finished
cutout width.
• The electrical and water locations must be located as
shown for either type of installation.
*36" Min. for a flush installation
35-1/2" Min. for a semi-flush installation
NOTE: Additional cutout width may be required when
side panels are used. Add side panel thickness to
the finished cutout to calculate rough-in width.
See installation examples on the following page.
Advance Planning
*Shipped at 84" installation height.
Can be adjusted to 83-1/2" or 84-1/2" with grille panel kits.
0"
3/4"
36"
Frame to Frame
84"*
26-1/4"
Including
Handle
35"
Case
Width
24-3/4"
Case
Depth
75" From Floor
to Bottom
of Electrical
Area
84 1/2" max
83 1/2" min
Finished
Opening
*Finished Width
Electrical
Area
5"
5"
3 1/2"
24 3/4" Total
Depth
Water Supply
3 1/2"
Wall View
2 1/2"
5"
6"
DESIGN
INFORMATION
4
For a complete food storage center,
install a Monogram Freezer and
Refrigerator side by side. Order ZUG75
Unified Grille Panel Kit for one
continuous 3/4" panel.
• Electrical and water locations must
be located as shown for either type of
installation. A separate 115V, 60Hz. 20
amp power supply is recommended
for each product.
NOTE: Additional cutout width may be required
when side panels are used. Add side panel
thickness to the finished cutout to calculate
rough-in width. See installation examples
below.
*72" min. for a flush installation
71-1/2" min. for a semi-flush installation
Side panels are required whenever the sides of the
product will be exposed.
1/2" to 3/4" side panels are normally set into place and
fastened to adjacent cabinetry or back wall before
rolling the refrigerator or freezer into the opening.
Therefore, the rough-in dimensions must allow for side
panel thickness. In a flush and semi-flush installation,
the finished dimension (width of the opening after side
panels are installed), must accommodate the full width
of the product. See page 11 for side panel sizes.
Side By Side Installation Of Freezer And Refrigerator
Installation Examples
2 1/2"
75" From Floor
to Bottom
of Electrical
Area
84 1/2" max
83 1/2" min
Finished
Opening
*Finished Width
Electrical
5"
5"
3 1/2"
24 3/4" Total
Depth
Water Supply
Wall View
6"
5"
6"
28 1/2"
26"
Freezer Refrigerator
Clearances
Factory set for a 130° door swing. Order WX14X99
adjustable door stop to reduce swing to as little as 90°.
When Installed into a corner:
Allow 25" for a full 130° door swing. Allow 15" for pan
removal. Allow 4" min. clearance when door swing is
adjusted to a 90° opening for pan access, but pan
removal is restricted.
Clearances for two products installed side-by-side
with the same (left or right) door swing
Allow 2" minimum clearance between the products to
prevent door swing interference. Order the WX14X99
adjustable door stop to reduce the factory set 130° door
swing. Allow 15" minimum to a wall to achieve full drawer
extension and pan removal. Additional clearances are
required when using custom handles and panels.
NOTE: ZUG75 Grille Panel Kit will not fit this installation.
25"
Min. to
Wall
130°
130° Door
Swing
36-3/4"
4" Min.
to Wall
90° Door Swing
25"
Min. to
Wall
0"
25"
Min. to
Wall
130° Door
Swing
130° Door
Swing
2"
15"
5"
Clearances for Multiple Single Door Installations
In a side-by-side installation of a left and right door
swing product, no clearance between the units is
required. If you are installing 3/4" thick custom panels,
order ZUG75 Unified Grille Panel Kit for one continuous
grille panel.
Clearances for two products installed side-by-side
with right and left side hinges together
Allow 5" minimum between the two products to prevent
one door from striking the other. Use the WX14X99
adjustable door stop to reduce the factory set 130° door
swing and to allow pan removal. Additional clearances
are required when using custom handles and panels.
NOTE: ZUG75 Grille Panel Kit will not fit this installation.
DESIGN
INFORMATION
Design Information
36" Refrigerators, Freezers
5
Installation
At End-of-Run
Frameless Cabinets
NOTE: 1/2" thick side panels shown.
Side panels can be any thickness.
Add side panel thickness to outside
trim width, (36” or 72" for two
models) to calculate the rough-in
dimension. The leading (front)
edge must be finished to match
surrounding cabinetry.
Side panels, 1/2" minimum thickness are required when
using frameless cabinets. The side panel acts as a
spacer between the cabinet and the case trim and
prevents interference with cabinet door swing. The
leading (front) edge must be finished to match
surrounding cabinetry.
1/2" To 3/4" Side Panels. Leading
Edge Flush With Cabinet
Accessory Panel Kits
These refrigerators and freezers require field installed
door and grille panels. The factory installed trim will
accept accessory panel kits. White or black Lexan
®
and
stainless steel kits are available. Panels are cut to size
and ready to install. Panel kits must be ordered
separately.
ZWBR36, Black Lexan
®
Panels
ZWWR36, White Lexan
®
Panels
ZWSR36, Stainless Steel Panels
Refrigerator or Freezer
Refrigerator and Freezer
installed side-by-side
These refrigerators and freezers are designed to be
customized with decorator door and grille panels. Field
installed custom door and grille panels are required.
Door and grille panel sizes vary to accommodate the kit
being used. Sizes are provided in this booklet.
CAUTION: Maximum door panel weight is 50 pounds.
Side panels must be used whenever the sides of the
refrigerator will be exposed. Side panel sizes vary
depending on the installation.
Advance
planning
exterior
appearance
options
3/4" thick custom panels-Without trim kits
A raised panel design, screwed or glued to a 1/4" thick
backing can be used. See page 8.
You should:
1. Select the appearance option.
2. Order the trim kit for that option.
3. Order the custom door and grille panels from the
cabinet manufacturer. The exact dimension for each
trim kit application is provided in this booklet. Find
and pull out the page for your application and fax or
send it to the cabinet manufacturer.
4. Determine the final installation situation and order
matching side panels.
73"
1/2" Thick
Side Panels
72"
Finished Dim.
Rough-In Dim.
Refrigerator
Cabinet
Refrigerator door
37"
1/2" Thick
Side Panels
36"
Finished Dim.
Roughed-In Dim.
Installation
Between
Base and
Wall Cabinets
NOTE: 1/4" thick side panels can be inserted into
the case trim, making the rough-in the same as
the outside trim width, 36”.
Refrigerator or Freezer
1/4" Thick
Side Panels
35-1/2"
Finished Dim.
36"
Rough-In Dim.
Cabinet
Refrigerator
Cabinet
Refrigerator door
Cabinet
Door
Refrigerator
Cabinet
Design Information
36" Refrigerators, Freezers
6
Trim kit descriptions
ZGC2 – Provides 1/4" grille panel frame side pieces for
83-1/2" and 84-1/2" installation heights. The supplied
grille panel frame is factory set for 84".
ZKHR1 – Provides the necessary framework to install a
custom handle, of your choice, onto a 1/4" thick panel.
(Handle not included.)
ZKHRSSI – Tubular stainless steel handle for 1/4" thick
panel installation.
ZKHTR1 – Provides the necessary framework to install
a custom handle, of your choice, onto a 3/4" thick panel.
(Handle not included.) This kit must be used in
combination with ZKTR36LH or ZKTR36RH.
ZKHTRSS1 – Tubular stainless steel handles for 3/4"
thick panel installations. This kit must be used in
combination with ZKTR36LH or ZKTR36RH.
ZKTR36LH (left opening models),
ZKTR36RH (right opening models) – Provides for the
installation of 3/4" thick custom door and grille panels.
This kit provides a standard handle to fit 3/4" thick
panels.
ZUG75 – For side by side installation of two products.
This kit provides for the installation of a unified 3/4"
custom grille panel to span the width of two products.
Includes a trim strip to cover inside case trim for a
more finished appearances. This kit must be used in
combination with both the ZKTR36LH and ZKTR36RH.
3/4" Custom panel with
Tubular Stainless Steel
handle, Trim Kits
ZKTR36LH (or ZKTR36RH)
and ZKHTRSSI.
1/4" Panel with standard
handles. No kits required.
1/4" Custom panel with
custom handles. Trim Kit
ZKHR1.
1/4" Custom panel with
Tubular Stainless Steel
handles, Trim Kit
ZKHRSS1.
3/4" Custom panels with
supplied handle. Trim Kit
ZKTR36LH (or ZKTR36RH).
3/4" Custom panel with
custom handle. Trim kits
ZKTR36LH (or ZKTR36RH)
and ZKHTR1.
ZIR36N RH, Refrigerator ZIF36N RH, Freezer
36" wide models with handle on left side, the door
swings left to right.
Models available
ZIR36N LH, Refrigerator ZIF36N LH, Freezer
36" wide models with handle on right side, the door
swings right to left.
Side by side installation
with 3/4" custom panels and
unified custom grille panel.
Trim Kits ZUG75, ZKTR36LH,
ZKTR36RH.
Design Information
36" Refrigerators, Freezers
7
ZIR36N Refrigerator
ZIF36N Freezer
Design Information
Designed to be installed flush or semi-flush with
surrounding cabinetry. Cutout dimensions, clearances
and side panel sizes are determined by the many
installation options available. Side panels must be used
whenever the sides of the refrigerator will be exposed.
Side panels are not required when installed into an
enclosure or between pantry and oven cabinets.
IMPORTANT – Side panels, 1/2" minimum thickness are
required when using FRAMELESS CABINETS.
• Field installed custom panels, Lexan
®
or stainless steel
panels are required. The door and grille panel sizes
vary to accommodate the kit being used.
• The supplied toekick is vented and must remain
unobstructed for proper air circulation.
Optional Panel Kits:
• ZWBR36: Black Lexan®Panel Kit
• ZWWR36: White Lexan
®
Panel Kit
• ZWSR36: Stainless Steel Panel Kit
Optional Custom Trim Kits:
• ZKHR1: For installation of a custom handle of your
choice onto a 1/4" Panel.
• ZKTR36LH or ZKTR36RH: For installation of a 3/4" thick
custom panel.
• ZKHTR1: For installation of a custom handle of your
choice onto a 3/4" thick panel. (This kit must be used in
combination with ZKTR36LH or ZKTR36RH).
• ZKHRSS1: Tubular Stainless Steel handle for 1/4" thick
panel.
• ZKHTRSS1: Tubular Stainless Steel handle for 3/4" thick
panel.
• ZGC2: 1/4" grille panel frame side pieces for 83-1/2" and
84-1/2" installation heights. (Factory set for 84").
• ZUG75: Unified 3/4" Grille Panel for side by side
installations. This kit must be used in combination with
ZKTR36LH and ZKTR36RH kits.
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install a
properly grounded
3-prong electrical receptacle recessed into the back
wall. Electrical must be located on rear wall as shown.
• Water line can enter opening through the floor or
back wall. The water line should be 1/4" O.D. copper
tubing or GE SmartConnect™ kit between the cold
water line and water connection location, long enough
to extend to the front of the refrigerator. Installation of
an easily accessible shut off valve is required.
* 36" Min. for a flush installation into an enclosure.
* 35-1/2" Min. for a semi-flush installation into an
enclosure.
NOTE: Additional cutout width may be required when
side panels are used. Add side panel thickness to the
finished cutout width to calculate rough-in width.
See installation examples, pages 4 and 5.
Clearances:
When installed into a corner:
Allow 25" for a full 130° door swing. Allow 15" for pan
removal. Allow 4" min. clearance when door swing is
adjusted to a 90° opening for pan access, but pan
removal is restricted. Order WX14X99 adjustable door
stop to reduce door swing to as little as 90°.
10-3/4" Max.
10" Min.
24-3/4"
35" Case
36" Overall
84-1/2" Max.
83-1/2" Min.
4"
73-1/2"
26-3/4"
6"
*Finished Width
Wall View
(not to Scale)
Locate Grounded
Electrical outlet
Within Solid
Area Above84 1/2" max
83 1/2" min
Finished
Opening
75" From
Floor to
Bottom of
Electrical Area
5"
5"
3 1/2"
5"
3 1/2"
2 1/2"
Locate Freezer Water
Supply Within
Shaded Area
Custom Panel Dimensions
36" Refrigerators, Freezers
8
Custom Door Panel Dimensions Using Standard Trim
1/4" thick panels
or
Panels secured to 1/4" thick backing
ZIR36N Refrigerator
ZIF36N Freezer
• 1/4" Panel: Cut panels to size.
• Custom handle with 1/4" door panel requires Trim kits
ZKHR1 or ZKHRSS1 for tubular stainless steel handles.
Standard Trim with Panels secured
to 1/4" thick backing
• Applying a raised panel design to a 1/4" thick backing
(screws or glued): Cut 1/4" thick panels to size.
Fabricate the raised panel to permit at least 2" fingertip
clearance of the standard handle. 1-1/4" clearance
from the hinge side to avoid striking adjacent
cabinetry and 5/16" from the top and bottom edges to
allow for the trim flange.
NOTE: ZKHTR1 custom handle kit cannot be used in this
configuration.
IMPORTANT: Maximum total weight for assembled
door panel is 67 lbs., maximum grille panel weight
is 9 lbs.
Installation Height Panel Height
83-1/2" 7-1/2"
84-1/2" 8-1/2"
The grille panel frame is factory assembled for 84"
installation height. If installation height varies, order
ZGC2 trim kit that provides optional side trim pieces.
Cut grille panel to sizes shown below.
35 1/8"
8" 1/4" Thick Panel
Custom Grille Panel
1-1/4"
Clearance
hinge side
Appearance
Panel
1/4"
Thick
Backing
Raised Panel on 1/4" Thick Backing
Using Standard Handles
2" Clearance
handle Side
Raised Panel
on 1/4" Thick
Backing With
Standard
Handles
5/16" Clearance
5/16" Clearance
5/16" Clearance
1/4" Thick
Custom Panel
35-1/16"
68-7/8"
CUSTOM PANEL
DIMENSIONS
Custom Panel Dimensions
36" Refrigerators, Freezers
9
ZIR36N Refrigerator
ZIF36N Freezer
• The ZKTR36LH (or ZKTR36RH) trim kit provides for the
installation of 3/4" thick custom door and grille panels,
using the supplied handle. Cut panel to size and install.
Custom Door Panel Dimensions
Using Trim Kits ZKTR36LH or ZKTR36RH
3/4" thick panel with kit supplied handle
Installation Height Dimension A
83-1/2" 7-3/4"
84" 8-1/4"
84-1/2" 8-3/4"
IMPORTANT: Maintain 1-1/2" min. gap between
top of door and bottom of grille panel.
Grille Panel height can vary to fill installation
height.
35 1/4"
A
3/4" Thick Panel
Custom Grille Panel
3/4" Thick
Custom Panel
35 -1/16"
68-15/16"
3/4" Thick Panel
A
71-3/8"
Unified Custom Grille Panel
Custom Panel Dimensions
36" Refrigerators, Freezers
IMPORTANT: Maximum door panel weight is 67 lbs.,
maximum grille panel weight is 9 lbs.
10
ZIR36N Refrigerator
ZIF36N Freezer
• The ZKTR36LH (or ZKTR36RH) trim kit installed
together with a ZKHTR1 custom handle kit provides
for the installation of 3/4" thick custom door and grille
panels with a custom handle of your choice. Order
ZKHTRSS1 for a tubular stainless steel handle.
Cut panels to size, rout the handle side of the panel
as shown below and install.
Custom Door Panel Dimensions Using Standard Trim
Using Trim Kit ZKTR36LH or ZKTR36RH
3/4" thick panel
with custom handle
Installation Height Dimension A
83-1/2 " 7-3/4"
84" 8-1/4"
84-1/2" 8-3/4"
IMPORTANT: Maintain 1-1/2" min. gap between
top of door and bottom of grille panel.
Grille Panel height can vary to fill installation
height.
35 1/4"
A
3/4" Thick Panel
Custom Grille Panel
3/4" Thick
Custom Panel
With Custom
Handle
35 1/4 "
68-15/16"
1/4"
max
Appearance Side
Rout back side of panel as shown
on the handle side
1-13/16"
3/4" Thick Panel
A
71-3/8"
Unified Custom Grille Panel
Custom Panel Dimensions
36" Refrigerators, Freezers
IMPORTANT: Maximum door panel weight is 67 lbs.,
maximum grille panel weight is 9 lbs.
23 5/16"
84"
2 5/16"
24 3/4"
84"
3 3/4"
23 9/16"
84"
2 9/16"
Trim
11
1/4" Side Panels
Insert end of
side panel into trim.
Use stick-on hook and
loop fastener strips to
secure the panel to the
refrigerator.
Standard 4" high toekick or trim to fit.
Height may vary depending on application.
1/2" to 3/4" Side Panels
Recessed front edge.
Standard 4" high toekick or trim to fit.
Height may vary depending on application.
1/2" to 3/4" Side Panels
Leading Edge
Flush with Cabinet
Front. The front or
leading edge must be
finished to match
cabinetry.
Standard 4" high toekick or trim to fit.
Height may vary depending on application.
Side Panel or Filler Options
(Not to scale)
Side panels must be used whenever the sides of the
refrigerator or freezer will be exposed.
Top View
Top View
Top View
CUSTOM PANEL
DIMENSIONS
Custom Panel Dimensions
36" Refrigerators, Freezers
12
Tools
Required
• Tinsnips to cut banding
• Stepladder
• 1-1/4" open-end wrench
• Bucket
• Level
• Appliance Hand Truck
• Tubing cutter
• 7/16" open-end wrench
• #2 Phillips screwdriver
• Stubby Phillips
screwdriver
• Drill and appropriate bits
• 7/16" socket with 3"
extension for ratchet
• Safety glasses
Materials
Required
Hardware
Supplied
Flooring
• 1/4-1/4 union with nuts
• Anti-Tip Mounting Brackets
• Water shut-off valve
• Water filter WR97X0214 (optional but recommended)
• Custom panel for door and grille panel.
• 1/4" Copper water line tubing or GE SmartConnect
™
Tubing Kit
For proper installation, the refrigerator or freezer must
be placed on a level surface of hard material the same
height as the rest of the flooring. The floor should be
strong enough to support a fully loaded refrigerator or
freezer, or approximately 1,200 lbs.
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under the
product where you are working.
Grounding the
Refrigerator
When disconnecting the power cord from the adapter,
always hold the adapter in place with one hand and
pulling the power cord with the other hand. If this is not
done, the adapter ground terminal is very likely to break
with repeated use.
Should the adapter ground terminal break, DO NOT USE
the appliance until a proper ground has again been
established.
Use of Extension Cords
Because of potential safety hazards under certain
conditions, we strongly recommend against the use of
an extension cord. However, if you still elect to use an
extension cord, it is absolutely necessary that it be a UL
listed 3-wire grounding type appliance extension cord
having a grounding type plug and outlet and that the
electrical rating of the cord be 15 amperes (minimum)
and 120 volts.
IMPORTANT – (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
The power cord of these appliances are equipped with
a three-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle to
minimize the possibility of electric shock hazard from
this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
IMPORTANT:
We recommend two separate 115V, 60Hz. 20 amp.,
properly grounded electrical outlets for a side by
side installation of two products. Each electrical
outlet should have a voltage rating that matches the
rating plate.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG
FROM THE POWER CORD.
Use of Adapter plug
Because of potential hazards under certain conditions,
we strongly recommend against use of an adapter plug.
However, if you still elect to use an adapter, where local
codes permit, a TEMPORARY CONNECTION, may be
made to a properly grounded 2-prong wall outlet by use
of a UL listed adapter available at most hardware stores.
The larger slot in the adapter must be aligned with the
larger slot in the wall outlet to provide proper polarity in
the connection of the power cord.
• Stick-on hook and loop fastener strips for 1/4" side
panels
• 35" long 2x4 for Anti-Tip support
• Screws to secure refrigerator to cabinetry
FICHE D’ADAPTATION
(Fiches d’adaptation non permises au Canada)
Attaching the adapter ground terminal to a wall
outlet cover screw does not ground the appliance
unless the cover screw is metal, and not insulated,
and the wall outlet is grounded through the house
wiring. You should have the circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
CAUTION
PRUDENCE
Installation
36" Refrigerators, Freezers
Loading...