GE ZIDI240BII User Manual
Depth of unit with 3/4" panels 24-7/8"
Depth of body 22-7/16"
Depth of toekick 2-7/16"
Height of toekick 4" (adjustable)
Refrigeration modules
Double-drawer refrigerator
general features
Temperature control. Digital touch controls maintain a
consistent temperature for the upper and lower drawers, and an
LED display allows you to monitor the temperature at a glance.
Storage convenience. A fold-down shelf, adjustable dividers
and removable bottom-drawer bin maximize storage space and
flexibility, allowing room for everything from whole melons to
large turkeys. The top drawer can hold up to 72 twelve-ounce
cans, and the bottom drawer has room for eight two-liter bottles.
Interior lighting. Brilliant full-width LED lighting in both drawers
puts contents into clear view.
Flush installation. The built-in configuration allows nearseamless integration with surrounding cabinetry. Model
ZIDI240WII accepts custom 3/4" panel and handle for
a personalized look.
For additional details on product installation, warranty
coverage, care and maintenance, visit monogram.com.
Double-drawer refrigerator
ZIDS240WSS—Stainless steel
ZIDI240WII—Custom panel
Overall dimensions*
(WxHxD in inches):
23-3/4 x 34 -1/4 –34-3/4 x 23-3/4
Amps @120 Volts 15
Approx. shipping wt. (lbs.) 126
•
Designed to be built-in only;
cannot be used free-standing
•
Factory-installed black toekick;
stainless toekick included
•
Trimmed model designed
to be customized with custom
panel and handle
•
Both designs can be installed flush
in standard 24"-deep cabinets
110
* Height excluding legs, depth excluding handle
Advance planning for double-drawer refrigerator
The installation space
The Monogram® double-drawer refrigerator must
be installed below a countertop. It cannot be used
free-standing.
Note: When installed, model ZIDI240WII with 3/4" custom
drawer panels and model ZIDS240WSS with stainless steel-
wrapped drawers will be flush with adjacent 24"-deep cabinets.
ZKDP240 Professional door with handle
This panel provides a Professional-style handle on a stainless
steel door panel. Transform the ZIDI240WII to complement a
commercial-style kitchen.
34-1/4" – 34-3/4"
22-7/16"
24-7/8"
34-1/2"-35"
Locate Outlet
10-1/2"
9"
Max.
23-3/4" Min.
Depth of unit with 3/4" panels 24-7/8"
Depth of body 22-7/16"
Depth of toekick 2-7/16"
Height of toekick 4" (adjustable)
2-7/16"
24" Min.
1-1/2"
25-7/8”
Including
Handles
23-5/8"
23-5/8"
34-1/4”
to 34-3/4”
Advance planning for double-drawer refrigerator
Overlay
Panel
1/4"
Backer
Panel
Door
3/4" custom panels for
fresh food and bar refrigerator
3/4" custom panels for
double drawer refrigerator
.10 Inch
Spacer
Spacer Panel
Backer Panel
Overlay Panel
Overlay
Panel
1/4"
Backer
Panel
Door
.10 Inch
Spacer
Spacer Panel
Backer Panel
Overlay Panel
3/4" custom panels for
double drawer refrigerator
B
A
1/4" Gap
12-1/2 lbs. max.
B
12-1/2 lbs. max.
Overlay
Panel
1/4"
Backer
Panel
Door
.10 Inch
Spacer
Spacer Panel
Backer Panel
Overlay Panel
monogram.com
Location requirements
All Monogram refrigeration modules may be closed in on
the top and sides as long as the front is unobstructed for air
circulation.
• Do not install these products where the temperatures will
go below 55°F (13°C) or above 90°F (32°C).
• Do not install where they will be subject to direct
sunlight, heat or moisture.
• These products are not designed to be stacked one over
the other.
Electrical
A 120V, 60HZ., 15- or 20-amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall of the installation
opening. See cutout illustration.
The serial plate is located below the bottom drawer liner on
the left side.
Note: GFCI (ground fault circuit interrupter) is not recommended.
Side-by-side installation
For the ultimate in convenience, install two double-drawer
refrigerators together.
• Products must operate from separate properly
grounded receptacles.
3/4" custom panels for
double-drawer refrigerator
Field-installed overlay drawer panels are required for
model ZIDI240WII.
• The overlay panel must be secured to a 1/4"-thick backer
panel that slides into the drawer trim. A 0.10"-thick spacer
panel must be placed between the overlay and backer panel.
• Custom handles of your choice must be installed onto the
assembled overlay panels.
Maximum assembled panel weight is
25 pounds (12-1/2 pounds for each panel).
3/4" overlay panel dimensions (in inches)
A (width) B (height)
1/4" backer 23-3/16" 14-11/16"
0.10" spacer 22-1/2" 14-3/16"
3/4" overlay 23-5/8" 15-1/16"
Note: Maintain 1/4" gap between the
drawer panels.
refrigerator
Double-drawer
bar refrigerator
Fresh-food refrigerator
refrigerator
Outdoor/indoor
Assemble overlay panels with glue and screws.
• Center spacer panel on the backer panel, left to right, and top
to bottom. Secure the panels with glue.
• Center the spacer/backer panel on the overlay panel. Secure
with glue and screws. Countersink all screws.
beverage center
Wine reserve, wine chiller
111
Loading...