GE ZGU48N6RWSS User Manual

™

Monogram.



ZGU48N6RWSS—48" Professional Gas Cooktop

Dimensions and Specifications (in inches)

Cooktop

Front Projects Outward as Shown From Standard Depth Cabinets.

Cooktop

Flush With Cabinet Front

Front Flush With Cabinets - a Minimum of 25-3/4" Cabinet Depth Required

1/2" Above Adjacent Countertops.

26-5/8"

This cooktop is factory set for natural gas and has 6 gas burners and a grill.

Liquid Propane Gas Model Also Available:

ZGU48L6RWSS–6 gas burners and a grill.

Installation Options:

This cooktop can be installed in standard 24" or deeper 25" cabinets.

• In 24" deep cabinets, the front of the cooktop will project approximately 1-7/8" beyond the front of the countertop.

• In 25" deep cabinets, the cooktop will be flush with the front of the countertop

• The stainless surface of the cooktop will be 1/2" higher than adjacent countertop.

Accessory Requirements:

All models require the installation of a backguard. A backguard should be ordered at the same time as the cooktop. Both should be on site before cabinetry has been installed.

Order one backguard:

ZXC1B48WSS–1-1/2" high backguard (required for island installations) ZXC12B48WSS–12" high backguard ZXC22B48WSS–22" high backguard with warming shelf (2 piece)

21-1/4"

Countertop  Level

8-7/16"

3" to Center Line

of Gas Inlet

Revised 7/97

High Back

12"

1/2"

Cabinet Face - Projecting Control Panel

Cabinet Face - Flush Control Panel

Low Back

22-3/4" 23-1/4"

2-1/2"

ZXC22B48WSS

ZXC12B48WSS

ZXC1B48WSS

For answers to your Monogram,®GE Profile, GE, Hotpoint and RCA appliance questions, call GE Answer Center®service, 800.626.2000.

Listed by Underwriters Laboratories

™

™

48" Wide Hood

30" Min.

36" Max.

18" Min.

12" Min. to Combustible Material Each Side

36" Min. to Combustible Material From Cooking  Surface

13" Max.

17"

22-3/4" Min.

Electric/Gas

Supply

46-1/8"

7/8"

2-1/2"

Cooking Surface

Monogram.



ZGU48N6RWSS—48" Professional Gas Cooktop

Dimensions and Specifications (in inches)

Advance Planning:

Refer to dimensional drawings for appropriate placement and necessary clearances when planning the installation.

• Cabinetry cannot be installed directly above the cooktop.

• This cooktop requires the installation of a vent hood, 30" to 36" above the surface. –The vent hood must be at least 24" deep. –The vent hood must be the same width as

the cooktop.

–The vent hood blower should provide at least

800 CFM and up to 1200 CFM.

–Choose a vent hood with 800CFM for best

performance when operating the grill.

2-1/2"

21-1/4"

12"

10"

Low Back

26-5/8"

High Shelf

36" Min. 

to Combustibles

12" Min. to Combustibles Without Backguard

Island Trim

36" Min. 

to Combustible

• Working areas adjacent to the range should have 18" minimum clearance between countertop and cabinet bottom.

• Clearance between cooktop and side wall or combustible material must be at least 12" on each side.

• This cooktop requires 8" free space below the countertop.

• If the cooktop is installed in an island: –Allow 12" min. clearance at the back to

combustible materials.

–Allow 36" min. above the cooking surface to

combustible materials.

• Installation must conform with local codes. In the absence of local codes, the gas cooktop must comply with the National Fuel Gas Code, ANSI Z223.1, latest edition.

A.G.A. approved

For answers to your Monogram,®GE Profile,

™

GE, Hotpoint and RCA appliance questions, call GE Answer Center®service, 800.626.2000.

Revised 7/97

Listed by Underwriters Laboratories

+ 2 hidden pages