GEAppliances.corn
Safety Information ........... 2, 3
Operating Instructions
Care and Cleaning............... 10, 11
Control and Indicator Settings ..... 4, 5
Loading and Using the Washer ...... 8
Features .......................... 6, 7
Installation Instructions .. 12-20
Troubleshooting Tips
Before You Call For Service .... 22-24
Status Indicators .................. 21
Consumer Support
Consumer Support ....... Back Cover
Warranty for Customers
in Canada ........................ 26
Warranty for Customers
in the U.S.A........................ 25
WSLPl 5O0
WSLS1500
Laveuses
La section frangaise commence _ la page 27
Lavadoras
Write the model and serial
numbers here:
#
#
You can find them on a label
on the back of the washer.
La secci6n en espaflol empieza en la p6gina 53
3828EV3068Q Rev: 0
49-90533 ii-14 GE
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
This isthe safety alert symbol.This symbol alerts you to potential hazardsthat can killyou or hurt you and others.All
safety messages will follow the safety alert symbol and the word "DANGER","WARNING",or "CAUTION".Thesewords are
defined as:
Indicates a hazardous situation which, if not avoided, will result in death or serious inJury.
Indicates a hazardous situation which, if not avoided, could result in death or serious inJury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate inJury.
IMPORTANT SAFETYINSTRUCTIONS
To reduce the risk of death, fire, explosion, electric shock, or injury to persons when using your
appliance, follow basicprecautions, including the following:
[] Readallinstructionsbeforeusingtheappliance.
[] DO NOTwash or dry articles that have been previously cleaned in,washed in, soaked in or spotted with gasoline,
dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or
explode.
[] DO NOTadd gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These
substances give off vapors that could ignite or explode.
[] Under certain conditions, hydrogen gas may be produced ina hot-water system that has not been used for 2
weeks or more. HYDROGENGAS ISEXPLOSIVE.If the hot water system has not been used for such a period, before
using a washing machine, turn on all hot-water faucets and let the water flow from each for several minutes. This
will release any accumulated hydrogen gas. As the gas is flammable, DO NOTsmoke or use an open flame during
this time.
[] DO NOTallow children to play on or in this appliance. Close supervision of children is necessary when this appliance
is used near children. Before the washer is removed from service or discarded, remove the door or lid. Failure to
follow these instructions may result in death or injury to persons.
[] DO NOTreach into the appliance if the basket or agitator is moving to prevent accidental entanglement.
[] DO NOTinstall or store this appliance where it will be exposed to the weather.
[] DO NOTtamper with controls, repair or replace any part of this appliance or attempt any servicing unless
specifically recommended inthe user maintenance instructions or in published user repair instructions that you
understand and have the skills to carry out.
[] Keepthe area around your appliance clean and dry to reducethe possibility of slipping.
[] DO NOToperate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts
including a damaged cord or plug.
[] Unplug the appliance or turn off the circuit breaker before servicing. Pressingthe Power button DOESNOTdisconnect
power.
[] See "Electrical Requirements" located in the Installation Instructions for grounding instructions.
SAVETHESE INSTRUCTIONS
GEAppliances.com
. PROPERINSTALLATION
This washer must be properly installed and located in accordance with the Installation Instructions before it is used.
If you did not receive on Installation Instructions, you con receive one by visiting GEAppliunces.com or by coiling
800.GE.CARES(800.432.2737). In Canada, visit www.GEAppliances.ca or coil 800.55.1..3344.
[] Ensurethat the hot water hose is connected to the "H"
(internalred screened)valve and the cold water hose is
connected to the "C"(internal blue screened)valve.
[]
Installor store where it will not be exposed to
temperatures below freezing or exposedto the weather,
which could cause permanent damage and invalidate
the warranty.
[]
Properlyground washer to conform with all
governing codes and ordinances. Follow details
in Installation Instructions.
[] Thiswasher does include water supply hoses.
GEstrongly recommends the use offactory specified
parts.A listof factory hosesavailable for purchase are
listed below.These hosesare manufactured and tested
to meet GEspecifications.
GEstrongly recommends the useof new water supply
hoses.Hoses degrade over time and need to be
replaced every 5 years to reducethe risk of hose failures
and water damage.
Parts and Accessories
'_ Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
DO NOT remove ground prong.
DO NOT use an adapter.
DO NOT use an extension cord.
Failure to do so can result in death, fire or electrical
shock.
WHEN NOT IN USE
[] Turn off water faucets to minimize leakage ifa break or
rupture should occur. Checkthe condition ofthe water
supply hoses;GErecommends changing the water
supply hoses every 5 years.
Order on-line at GEApplionceports.com today, 24 hours a
day or byphone at 800.626.2002during normal business
hours. InCanada,visit your local GEparts distributor or call
800.661.1616.
Pert Number
PM14XlO002
Or
PH14XlO005
WXlOXlO011 Tide®Washing Hachine Cleaner*
PH7X! Washer FloorTray
Accessory
4 ft Rubber Water Supply Hoses
4 ft Braided MetalWater SupplyHoses
SAVE THESE INSTRUCTIONS
* Tide® is a registered trademark of Procter & Gamble 3
About the controland indicator settings.
Before starting the washer:
, Sortlaundry by color and/or fabric type.
, Load laundry in the washer.
, Add detergent to the dispenser drawer.
, Add fabric softener to the fabric softener dispenser.
, Add bleach, ifdesired,to the bleach dispenser.
Power
Press the Power button to turn on the control panel.
NOTE:Pressing Power does not disconnect the appliance from the power supply.
Power
©
Cycles
Press the Cycles button to select the desired cycle.
For heavily to lightly soiled colorfast cottons, household linens,work and play clothes. Thiscycle
Normal providesthe bestoverallcleaningand should be usedfor most everydayitems.Providesnormalwash
Delicates Forlingerie and special-care fabrics with lightto normal soil.Provideslight wash and low speed spin.
Speed Wash high speed spin.
Heavy Duty cycleisextended for extra cleaning.This more aggressive cycleshould be usedsparingly.
Handwash wash and rinse.
Soak Cycle An extended wash cycle to loosen embedded soils and stains.
My Cycle and start.
Basket Clean NOTE: Never load laundry while using Bosket Cleon. The laundry may become damaged. See
Deep Fill
Increases the amount of wash water during all cycles except for Bosket Cleon.
and medium speedspin.
Forsmall loadsof lightly soileditemsthat are needed in a hurry. Provideslight wash/rinse and short
An above normal cyclefor heavily soiled or stained clothes.A soak cycle isadded and the agitate
For items labeled hand-washable with light soils. Provides gentle tumbling and soak during
Tosave a favorite cycle, set Cycles to My Cycle and select the desired Process, Options and
Woter Temp settings. Pressthe Stert button. The washer will automatically save the setting
To change the MYCycle, re-save following the above process.
To use My Cycle, set Cycles to My Cycle and press the Stort button.
Use for cleaning the basket of residue and odor. Recommended use ofot leost once per month.
the Cure end Cleuning section.
4
GEAppliances.com
Options
Press the Options button to select the desired options.
Select to spin excessive water out of swimwear. NOTE:This is NOTa wash cycle. This option
Swimwear can only be selected after turning the unit on by pressing Power. Do NOT load more than 4
pounds of clothes into the washer.
When you use extra detergent or bleach to clean heavily soiled clothes, use the Extra Rinse
Extra Rinse option to better remove additional residues. NOTE:This option is available for Normal, Heavy
Duty, Soak Cycle and My Cycle.
Providesa lowerspin speed.NOTE:This option will be selected automatically in Delicates,
Gentle Spin Handwash and Soak Cycle. This option is available for Heavy Duty and My Cycle.
Water Tamp
Select the water temperature for the wash cycle: Hot; Warm (hot and cold); Cold. Always follow fabric manufacturer's
care label or instructions when laundering.
NOTEFORPORTABLEMODELS:When using a one-faucet connection, adjust the water flow mix and water
temperature at the faucet.
Process
Chose the wash options to include in the cycle. Pressthe Process button until all the options you want to include are
lit. Morethan one option can be selected.
Soak
Wash Select to set a wash cycle only. Washer basket will fill, wash and drain.
Rinse Select to set a rinse cycle only. Washer basket will rinse and spin.
Spin Select to set a spin cycle only. Washer basket will spin.
Select to set a soak cycle only. Washer basket will fill, soak and drain.
NOTE: This option is available for Normal, Heavy Duty, Soak Cycle and Ny Cycle.
Delay Wash
You can delay the start of a wash cycle for 3-48 hours. Press the Delay Wash button to choose the number of hours
you want to delay the start of the cycle, then press the Start/Pause button. The machine willcount down and start
automatically at the correct time.
NOTE:Ifyou forget to fully close the rid,a reminder signal willbeep reminding you to do so.
NOTE:Ifyou open the lidwhen the delay is counting down, the machine willenter the pause state. You must close the lidand
press Start/Pause again in order to restart the countdown.
To cancel Delay Wash, press Power to restart.
Start/Pause
Pressto start a cycle.Ifthe washer isrunning,pressingit once will pausethe washer.Pressagainto restart the cycle.
NOTE:Ifthe washer is pausedandthe cycle isnot restarted within 15minutes,the current cyclewill be cancelled.
Lock Controls
You can lockthe controls to prevent any selectionsfrom being made.Controlscan be locked or unlockedafter you have
started a cycle.
Tolock/unlock the washer, pressand hold the Processand Cyclesbuttons for 3 seconds.
A sound ismade to indicate the lock/unlock status.
Mute Signal
Toturn the signalsoundson/off, pressand hold the Deep Filland Processbuttons for 3 seconds.
Display
The display shows the approximate time remaining until the end of the cycle.
NOTE:The cycle time isaffected by how long it takes the washer to fill.This depends on the water pressure in your home.
NOTE:IfDelay Wash is set, Delay and the time remaining until the cycle starts willbe shown before the remaining cycle
time is displayed. 5
Washer features.
Features and appearance wi!! vary throughout this manua!
Powder Detergent (/_)
Dispenser Drawer
Detergentwillautomatically
dispense into the wash
basket
Fabric Softener,
Dispenser (,_:%)
Fabric softener will
automatically dispense
into the wash basket
Liquid Bleach
Dispenser (_)
Bleach will automatically
dispense into the wash
basket
Control Panel
Hoses
Hake surehose
connectionsdo not leak
Power Cord
Drain Hose and
U-Shaped Guide
_ Wash Basket
Lint Filter
Clean the lint filter
as necessary.
Base
Powder Detergent
Dispenser Drawer
Powder Detergent Dispenser Drawer
Add powder detergent by pouring it in the
back center powder dispenser drawer. Most
detergent will immediately enter the basket.
Liquid detergent should be added directly to
the wash basket following the manufacturer's
directions.
GEAppliances.com
Q O NOTput detergent packets in
dispenser compartments. Laundry
detergent packets should only be
added directly to the wash basket following
the manufacturer's directions.
._@_
LiquidSoftener
Dispenser
LiquidBleach
Dispenser
Fabric Softener Dispenser
Add liquid fabric softener by pouring it into the
left center fabric softener dispenser. The liquid
will be added at the optimum time in the rinse
cycle.
Liquid Bleach
Add liquid bleach by pouring it into the left front
liquid bleach dispenser. The water filldilutes
liquid chlorine bleach as the washer fillsfor the
wash cycle.
rll Check clothing cure labels for special
instructions.
r_ Measure liquid bleach carefully, following
instructions on the bottle.
[] Never pour undilutedliquid chlorine
bleachdirectly onto clothesor into the
wash basket.
[] Do not pour powdered bleach into
bleach compartment.
@ O NOT put detergent packets in
dispenser compartments. Laundry
detergent packets should only be
added directly to the wash basket following
the manufacturer's directions.
[_] Beforestarting the washer, pour measured
amount of bleach directly into bleach
compartment. Avoid splashing or over-filling
dispenser.Ifyou prefer to use powdered
bleach, add it into the wash basket with
your detergent.
[] Donot mix chlorine bleachwith
ammonia or acidssuchas vinegar and/
or rust remover. Mixing canproduce a
toxic gas which may causedeath.
Q DO NOTput detergent packets in
dispenser compartments. Laundry
detergent packets should only be
added directly to the wash basket following
the manufacturer's directions.
Loading and using the washer.
Always follow fabric manufacturer's care label when laundering.
ProperUseofDetergent
Using too little or too much detergent is a
common cause of laundry problems.
Use less detergent if you have soft water, a
smaller load or a lightly soiled load.
Forspots, apply pre-treatment to items as
recommended on the product label.Application
should be made in the basket to prevent overspray
which may cause the coloring on the lid or graphics
to fade.
GErecommends the use of High Efficiency
detergents in all Energy Star rated washers. HE
detergents are formulated to work with low water
wash and rinse systems. HEdetergents reduce
the oversudsing problems commonly associated
with regular detergents.
When using high efficiency or concentrated
detergents, consult the product label to determine
amount required for optimum performance.
Excessive detergent will negatively impact wash
performance.
SortingWashLoads
Sort by color (whites, lights, colors),soil level,
fabric type (sturdy cottons, easy care, delicates)
- Fire Hazard
Neverplace items in the washer that are dampened with gasoline or other flammable liquids.
Nowasher can completely remove oil.
Donot dry anything that hasever had any type of oil on it (including cooking oils).
Doingso can result in death, explosion,or fire.
and whether the fabric produces lint (terry cloth,
chenille) or collects lint (velveteen, corduroy).
ClothesLevel
WaterLevel
theWasher
Load dry items loosely in the washer basket. For
best results, load items evenly and loosely around
the outside of the basket. To add items after
washer has started, pressPause, lift the lid and
submerge additional items around the outside of
the basket. Close the lid and press Start to resume.
Average Small Load Average Medium Load Average Large Load
ClothesLevel
Water Level
[] Do not place large items such as sheets, blankets
and towels across the infusor. Load them around
the outside of the basket.
[] Do not put lawn or sofa cushions into the washer
asthey are too big to move. Removeouter covers
and ONLYwash them.
ClothesLevel
Water Level
NO teS. GEAppliances.com
Care and cleaning of the washer.
Interior of the Washer
To clean the interior of the washer, select the
Basket Clean feature on the control panel.
This Basket Clean cycle should be performed,
at a minimum, once per month. This cycle
will use more water, in addition to bleach, to
control the rate at which soils and detergents
may accumulate in your washer,
NOTE:Read the instructions below
completely before starting the Basket Clean
cycle.
1. Remove any garments or objects from the
washer and ensure the washer basket is
empty.
Pour into the
washer basket
2. Open the washer lid and pour one cup or
250 ml of liquid bleach or other washing
machine cleaner into the basket.
.
Closethe lid and select the Basket Clean
cycle. Push the Start button.
4.
When the Basket Clean cycle is working,
the display will show the estimated cycle
time remaining. The cycle will complete in
about 3 hours. Do not interrupt the cycle.
BasketCleanmay be interrupted by pressing
the Start pad in between cycles. A power
outage in the house might also interrupt the
cycle. When the power supply is back, the
Basket Clean cycle resumes where it had
stopped. When interrupted, be sure to run a
complete Basket Clean cycle before using the
washer. If the Power pad is pressed during
Basket Clean, the cycle will be lost.
IMPORTANT:
[] Run Basket Clean with 1 Cup (250 ml) of
bleach once a month.
[] After the completion of a Basket Clean
cycle, the interior of your washer may
have a bleach smell.
[] It is recommended to run a light color load
after the Basket Clean cycle.
Push top down
and pull out
Lint Filter
Cleanas needed especially after washing loads
of lint producing items such as towels.
1. Remove the blue lint filters from the side of
the basket by unclipping.
2. Open the blue disc, remove all lint, rinse
and close.
3. Replace by snapping filter back into its
location in the washer basket.
o
10
Exterior of the Washer
Immediately wipe off any spills.Wipe with damp
cloth.Try not to hit surface with sharp objects.
Pump Filter and Housing
Cleanas needed to remove any items that may
have been caught in the filter or housing.
1. At the bottom back of the washer, place
a towel on the floor under the filter cap to
catch any water that may flow out.
2. Turn the filter cap counter-clockwise and
pull to remove.
3. Remove any objects and lint from the
housing and filter.
GEAppliances.com
Housing
rib
4. Replace the filter by aligning its guide rib
with the housing rails, pushing all the way
in and turning clockwise to lock in place.
Inlet Water Valve Screen,s)
If the flow of entering water into the washer
isslow,the inletwater valve screen(s)may be
clogged.
1. Turn off water valve(s).
2. Disconnect water hose(s)from the back of
the washer.
3. Remove the screen(s),clean with a brush
and replace.
4. Replace the hose(s).
S. Turn water valves on.
6. Check for leaks,tighten if necessary.
Water Supply Hoses
Hosesconnecting washer to faucet should be
replaced every 5 years.
Noving and Storage
Askthe servicetechnician to remove water from
drain pump and hoses. Donot storethe washer
where it will be exposed to the weather.
Long Vacations
Besurewater supply is shut off at faucets. Drain
all water from hosesand water filter pump area
ifweather will be below freezing.
11
I
stall ti
I
structi
If you hove uny questions, call 800.GE.CARES (800.432.2737)
or visit our Website at: GEAppliunces.com
In Cunudu, call 800.561.3344 or visit www.GEAppliunces.cu
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill you or hurt you and
A
others. All safety messages will follow the safety alert symbol and the word "DANGER","WARNING", or
"CAUTION".These words are defined as:
Indicates a hazardous situation which, if not avoided, will result in death or serious inJury.
Indicates a hazardous situation which, if not avoided, could result in death or serious inJury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate inJury.
SPECIFICATIONS
WSLP1500 end WSLS1500
Wa hers
Type
Bosket copocity
Electricol rotings
Wosh system
Outer dimensions
Weight
Electricity supply
120V, 60Hz
Fully automatic
2,6cu,ft,
120V,60Hz
Rotating drum
23 1/4" (W)x 23 7/8" (D)x 36 1/2" (H)
59.06cm (W)x 60.65cm (D)x 928mm (H)
90 1/2 Ibs.(41kg)
12
Installation Instructions
BEFORE YOU BEGIN
Read these instructions completely and carefully.
. IMPORTANT - Savetheseinstructions
for local inspector's use.
" IMPORTANT - Observe all governing
codes and ordinances.
. Note to Installer - Besure to leave these
instructions with the Consumer.
. Note to Consumer - Keepthese instructions
for future reference.
. Skill level - Installation of this appliance requires
basic mechanical skills.
. Completion time- 1 hour
. Properinstallationisthe responsibilityofthe
installer.
Product failure due to improper installation is not
covered under the Warranty.
Note - This appliance must be properly grounded,
and electrical service to the washer must conform
with local codes and ordinances and the latest
edition of the National Electrical Code, ANSI/NFPA70.
PLUMBING
WATERPRESSURE--Mustbe 10 p.s.i, minimum to
150 p.s.i,maximum dynamic pressure measured at
faucet.
WATERTEMPERATURE--Household water
heater should be set to deliver water at 120° to
!50°F (50° to 66°C) IN THEWASHERwhen HOTwash
is selected.
SHUT-OFF VALVES--Both hot and cold shut-off
valves (faucets) should be supplied.
DRAIN--Water may be drained into a standpipe or
set tub. The discharge height MUST NOT BE LESS
THAN 30" nor more than 8' above the base of the
washer. The standpipe must be !½" minimum inside
diameter and must be open to the atmosphere.
RACK INSTALLATION
. Ensure washer iscentered between the rack sides.
PARTS SUPPLIED
WASHER LOCATION
Washer must be installed on firm flooring to minimize
vibration during spin cycles. Concrete flooring is best,
but wood base is sufficient providing floor support
meets FHAstandards. Washer should not be installed
on rugs or exposed to the weather.
Install or store where it will not be exposed to
temperatures below freezing or exposed to the
weather.
ELECTRICAL
This appliance must be supplied with the voltage and
frequency indicated on the rating plate (located on
the back of the washer) and connected to an
individual, properly grounded branch circuit, protected
by a 15- or 20-amp circuit breaker or time-delay fuse.
Drain Hose
Water Hoses (2)
TOOLS REQUIRED
Pliers
13
Installation Instructions
ELECTRICAL REQUIREMENTS
_ f_,- Fire
Plug into a grounded 3-prong outlet.
DO NOT remove ground prong.
DO NOT use an adapter.
DO NOT use an extension cord.
Failure to follow these instructions can result in death,
fire or electrical shock.
CIRCUIT- Individual, properly polarized and grounded 15
or 20 amp circuit breaker or time-delay fuse.
POWERSUPPLY- 2 wire plus ground, 120 Volt, single
phase, 60 Hz,alternating current.
Outlet Receptacle - Properly grounded _st--,1
3-prong receptacle to be located sothe
power cord isaccessible when the washer
is in an installed position. If a 2-prong
receptacle is present, it is the owner's
responsibility to have a licensed electrician replace it with
a properly grounded 3-prong grounding type receptacle.
Washer must be electrically grounded in accordance with
local codes and ordinances,or in the absence of localcodes,
in accordance with the NATIONALELECTRICALCODE,ANSI/
NFPANO.70 latest edition. Checkwith a licensedelectrician if
you are not sure that the washer is properly grounded.
Hazard
ALL MODELS
Eli FOR YOUR SAFETY
Before beginning the installation,
unplug the appliance or turn off the
circuit breaker. Pressing the Power button DOESNOT
disconnect power.
_)- Entanglement
. A child or adult can become entangled and result in
serious injury.
. Install the base cover to the unit by sliding cover in
place and screwing into the unit.
. Failure to do so can result in serious injury.
Base Cover
Kit Included
If you did not receive a base cover with your purchase,
call 800.626.8774 to receive one at no cost. (In Canada, call
800.561.3344.)For installation instructions of the cover,visit:
www.GEAppliances.com.(InCanada, www.GEAppliances.ca.)
STATIONARY MODELS
GROUNDING INSTRUCTIONS
This appliance must be grounded. Inthe event of
malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance
for electric current. This appliance is equipped with a
cord having an equipment- grounding conductor and
a grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
_ mproper connection of the equipment-
of electrical shock. Checkwith u qualified electrician, or
servicerepresentative or personnel,ifyou are in doubt usto
whether the appliance isproperly grounded.DO NOTmodify
the plug on the power supplycord. If it will notfit the outlet,
have u proper outlet installed by u qualified electrician.
If required by local codes, an external 18 gauge or larger
copper ground wire (not provided) may be added. Attach
to washer cabinet with a #8-18 x 1/2"sheet metal screw
(available at any hardware store) to rear of washer.
Mobile Home Installation:
Installation must conform to Standard for Mobile Homes,
ANSIAl19.1 and National Mobile Home Construction and
Safety Standards Act of 1974 (PL93-383).
!groundingconductor can result inu risk
MAKE SURE WASHER IS IN ITS FINAL
LOCATION AND ADJUST LEGS
Adjust the legs of the
washer by lifting up the
front of the unit and
rotating the legs clockwise
until the unit is level.
PORTABLE MODELS
[-;] INSTALL FRONT LEG STOPPERS
To prevent the washer from "walking" during a spin
cycle, tilt the washer back slightly and insert the leg
stoppers under the front legs.
t _Caster
Leg stopper wheel
14
Installation Instructions
WASHER CONNECTIONS - STATIONARY MODEL WSLS1500
A WARNING: Mo,esure thewasheris
unplugged.
[_] FLUSH WATER LINES
Runsome water from the hot and cold faucets
to flush the water linesand remove particlesthat
might clog up the water valvescreens.
_]CONNECT TO WATER LINES
Connectthe inlet hoseends to the HOTand COLD
water faucets tightly by hand, then tighten another
turn with pliers.Turn the water on and check for
leaks.Retighten if necessary.
F4-1CONNECT DRAIN HOSE
Form a U shape on the end of the drain hosewith
the hose pointed toward the drain. Placethe hosein
a laundry tub or stand pipe and secure it with acable
tie (not included).
NOTE:Ifthe drain hose is placed in a stand pipe
without forming a Ushape, a siphoning action could
occur.There must be an air gap around the drain
hose.A snug hosefit can alsocause a siphoning
action.
Cable Tie
LaundryTub
I-_ CAREFULLY MOVE THE WASHER
TO ITS FINAL LOCATION
Cable Tie
Cable Tie
Stand Pipe
[]PLUG THE POWER CORD INTO A
GROUNDED OUTLET
/
Ensure proper ground
exists before use
15
Installation Instructions
WASHER CONNECTIONS - STATIONARY MODEL WSLS1500
%INSTALLATION CH ECKLIST
Before starting the washer, check to make sure:
klain power isturned on.
CIThewasher isplugged in.
CIThewater faucets are turned on,
CITheunit is level.
CIThedrain hoseis properly tied up.
CIThereare no leaks at the faucet, drain line
or washer.
I-_ RUN THE WASHER THROUGH A
COMPLETE CYCLE
Checkfor water leaksand proper operation.
i81REMOVE THE PROTECTIVE FILM
COVERING THE CONTROL PANEL
i_ READ THE REST OF THIS OWNER'S
MANUAL
It contains valuable and helpful information that will
save you time and money.
OWNERS
MANUAL
ALCOVE OR CLOSET INSTALLATION
If your washer is approved for installation in an alcove or
closet, there will be a label on the back of the machine
describing requirements.
. Minimum clearances between washer and adjacent
walls or other surfaces are: !" either side, 2" front,
4" rear.
. Minimum vertical space from washer to overhead
shelves, cabinets, ceilings, etc. is 24:'
. Closet doors must be Iouvered or otherwise ventilated
and have at least 60 square inches open area for
washer only, or if the closet contains both a washer
and dryer, doors must contain at least 120 square
inches of open area equally distributed.
NOTE:The clearances stated on this label are minimums.
Consideration must be given to providing adequate
clearances for installation and servicing.
16
NOTE: Ifyour washer does not operate, please
review the Before You Call For Service section.
$
60sq.in.
(387.1sq.crn)
O
60sq. in.
(387.1sq.cm)
Closet door
Installation Instructions
WASHER CONNECTIONS FOR PORTABLE MODEL
WSLP1500-- ONE-FAUCET CONNECTIONS
Use the hose connector provided with the washer for a
one-faucet connection.
_]CONNECT TO VALVE INLET
TO CONNECT THE WASHER:
T
[] REMOVE THE UNI-COUPLE ® HOSE
FROM INSIDE THE WASHER BASKET
Drain Connection
Faucet Connector
Water Filter
Uni-Coupler Hose
Attach the COLD water supply connector to the
COLD water valve inlet (color BLUE).Make sure the
washer is inside the connector before tightening.
[-4]TIG HTEN CONNECTOR
Tighten the connector, ensuring the threads are
aligned properly for tightest fit. Inspect for kinks
or binding of the hose.
[][]CONNECT TO WATER LINE
Attach the hose connector to the faucet adapter by
pulling down on the locking collar while lifting up on
the connector until it snaps into place. Make sure
the water filter provided is in place.
Locking Collar
t
Hose Connector
[][]CONNECT DRAIN HOSE
Attach the drain hose to the rear of the washer.
Install the clump on the drain hose and tighten to
prevent leakage of water.
17
Installation Instructions
WASHER CONNECTIONS FOR PORTABLE MODEL
WSLP1500-- ONE-FAUCET CONNECTIONS (CONT.)
_] MAKE SURE THE TEMPERATURE
SELECTOR IS SET AT COLD
[] SLOWLY TURN ON THE WATER
FAUCET ALL THE WAY TO THE
DESIRED TEMPERATURE SETTING
_] PLUG THE POWER CORD INTO A
3-PRONG GROUNDED OUTLET
r9] REMOVE THE PROTECTIVE FILM
COVERING THE CONTROL PANEL
IT0]INSTALLATION CH ECKLIST
Before starting the washer, check to make sure:
CI Main power is turned on.
CI The washer is plugged in.
CI The water faucets are turned on.
Theunit is level.
Thereare no leaks at the faucet drain line
or washer.
The electrical power cord is on the back of the
washer.
z'C.'
Ensure proper ground
exists before use
1
18
Installation Instructions
TO DISCONNECT THE WASHER:
_-] TURN WATER FAUCET OFF
[] UNPLUG POWER CORD AND
RETURN IT TO THE STORAGE AREA
[-4-]DISCONNECT FROM WATER LINE
Hove the locking collar down and pull the hose
connector down to disengage from the faucet
adapter.
Locking Collar
Hose Connector
[_] DRAIN WATER
Drain water from the hoses through the
hose connector.
[-J] PRESS THE RED WATER FLOW
BUTTON TO RELEASE THE WATER
PRESSURE
Water
Flow
Button
Hose Connector
19
Installation Instructions
WASHER CONNECTIONS FOR PORTABLE MODEL
WSLP1500--TWO-FAUCET CONNECTIONS
If you have two separate water connections, your washer
can be connected to both the hot and cold water faucets.
This kit can be purchased from your dealer or from Parts
and Accessories. In the United States, call 800.626.2002.
In Canada, consult the yellow pages for your local Mabe
Canada number.
TO CONNECT THE WASHER:
[_] CONNECT TO WATER LINE
Connect HOT and COLDwater inlet hoses to the
HOT and COLDfaucets.
[]PLUG THE POWER CORD INTO A
3-PRONG GROUNDED OUTLET
Ensure proper ground
exists before use
[-4-]INSTALLATION CH ECKLIST
Before starting the washer, check to make sure:
E_Main power is turned on.
Thewasher is plugged in.
Thewater faucets are turned on.
i
1
_]CONNECT DRAIN HOSE
Secure the drain hose to the sink or stand pipe.
Cable
Tie
Sink
Stand Pipe
Cable
Tie
Theunit is level.
I_ The drain hose is properly tied up.
I_ There are no leaksat the faucet, drain line
or washer.
TO DISCONNECT THE WASHER:
j[_ TURN WATER FAUCETS OFF i
[Z]UNPLUG POWER CORD AND
RETURN IT TO THE STORAGE AREA
i-_ DISCONNECT THE DRAIN AND
WATER SUPPLY HOSES
Hang them on the storage rack.
20
Before you call for service... 6EAppliances.com
Troubleshooting Tips
Save time and money! Review the charts on the following pages
first and you may not need to coil for service.
Status Indicators
[] Indicates washer failed to fill. Ensure wall faucets are on and fill hose is
not clogged or kinked.
[] Indicates water has not drained from washer. Ensure the drain hose is
not kinked or connected improperly.
[] Indicates the laundry load is unbalanced. Reposition laundry evenly in
basket, and ensure washer is level.
[] Indicates the lid is open. Close the lid.
[] Press Power and call service.
[] Indicates water has overflowed. Restart after spinning.
21
Before you call for service...
_ Troubleshooting Tips
POSSIBLECAUSES WHATTODO
Toomany suds Type of detergent • Switchto HE_ detergent,
Very soft water • Try less detergent.
Too much detergent _ Measureyour detergent carefully. Uselesssoap ifyou
have soft water, a smaller load or a lightly soiledload.
Water leaks Fill hoses or drain hose is . Hake sure hoseconnections are tight at faucets and
improperly connected the washing machine. Hake sure the end ofthe drain
hoseis correctly inserted and secured to the drain.
Household drain may be clogged _ Checkhousehold plumbing. You may need to call a
plumber.
Constant water pressure to the fill _Tighten hosesat the faucets and turn the water off
hoses at the water source after each use.
Checkcondition of the fill hoses;they may need
replacement after 5years.
Using too much detergent in . Uselessdetergent. Uselesssoap ifyou have soft
washer water, a smaller load or a lightly soiled load.
Water temperature is Water supply is turned off or . Turn both hot and cold faucets fully on and make sure
incorrect improperly connected hosesare connected to correct faucets.
Water valve screens are stopped _Turnoff the water source and remove the water
up connectionhosesfrom the upperback ofthe washer.
Removescreensand usea brushortoothpickto clean
the screens inthe machine.Reinstallscreens,reconnect
the hosesand turn the water buckon.
House water heater is not set * Hake sure housewater heater isdelivering water at
properly !20°F-!40°F (48°C-60°C).
Water won't drain Drain hose is kinked orimproperly . Straighten drain hose and make sure washer is not
connected sitting on it.
Top of drain outlet should be lessthan 8 ft. above floor.
Pump clogged _ Removeand clean pump filter.
POSSIBLECAUSES WHATTO00
Washer pauses in cycle Thewasher normally pauses
between washing steps
Washer won't operate Washer is unplugged _ Hake surecord is plugged securely into a working
outlet.
Water supply is turned off • Turn both hot and cold faucets fully on.
Controls are not set properly • Make sure all selections have been made.
Lid isopen • Closelid and pressStart/Pause.
Circuit breaker/fuse is tripped/ _ Checkhouse circuit breakers/fuses.Replacefusesor
blown reset breaker.Washer should have separate outlet.
Washer has not been turned on _ Pressthe Power button.
22
GEAppliances.com
POSSIBLECAUSES WHATTO DO
Coloredspots Incorrect use of fabric softener , Checkfabric softener package for instructions and
follow directions for usingdispenser.
Dye transfer . Sortwhites or lightly colored items from dark colors.
Grayed oryellowed Not enough detergent • Usemore detergent (especiallywith larger loads).
clothes
Lint or residue on Clothes are air or line dried . Ifyou do not dryyour clothes with a clothes dryer,your
clothes clothes may retain more lint.
Hard water o Usea water conditioner likeCalgon brand or install a
water softener.
Water is not hot enough • Makesure water heater is delivering water at
120°F-140°F(48°C-60°C).
Washer is overloaded _ Loadclothes no higher than the top row of holes inthe
washer basket
Dye transfer _Sort clothes by color. Iffabric label states wash
separately, unstable dyes may be indicated.
Incorrect sorting oSeparate lint producers from lint collectors.
Washing too long _Wash small loads for a shorter time than larger loads.
Overloading _ Loadclothes no higher than the top row of holes in the
Pilling Result of normal wear on . While this is not caused bythe washer, you can slow
poly-cotton blends and fuzzy the pilling processby washing garments inside out.
fabrics
Snags, holes, tears, rips Pins,snaps, hooks, sharp buttons, . Fastensnaps,hooks,buttons and zippers.
or excessive wear belt buckles, zippers, and sharp o Removeloose items like pins,objects in pockets and
objects left in pockets sharp buttons.
Undiluted chlorine bleach . Check bleach package instructions for proper amount.
Chemicals like hair bleach or dye, * Rinseitems that may have chemicals on them before
permanent wave solution washing.
Wrinkling Improper sorting oAvoid mixing heavy items (likework clothes)with light
Overloading or incorrect water * Loadyour washer soclothes have enough room to
level move freely.
Repeated washing in water that is _Wash inwarm or cold water.
too hot
washer basket
Turn knits (which snag easily)inside out.
Neveradd undiluted bleach to wash or allow clothes to
come in contact with undiluted bleach.
items(like blouses).
Try a fabric softener.
23
Before you call for service...
_ Troubleshooting Tips
POSSIBLECAUSES WHATTODO
WaSherisnoisy Washer is uneven • Levelthe washer. SeeLevelingthe Washer.
Washer load is unbalanced . Pressthe Start/Pause button to stop the washer,open
the lidand redistribute the load evenly. Closethe lid
and restart.
Washer is sitting too close to wall . Pullwasher away from the wall; about 4" isneeded
(causes knocking during cycle}
POSSIBLECAUSES WHATTODO
Labels onthe exterior Occasionally the adhesive used on
of the washer willnot the labels does not release cleanly
pee! off deanly
, Useo hair dryer set at the lowest heat setting, directing
the air at the labelfor a short amount of time. Thiswill
releasethe adhesive easily,without damaging the
surface of the washer.
24