GE UR F35 Series Instruction Manual

Download

832761A2.CDR

LISTED

52TL

IND.CONT. EQ.

E83849

Grid Solutions

GEK-119558C

F35 Multiple Feeder Protection

System

UR Series Instruction Manual

F35 Revision: 7.2x

Manual P/N: 1601-0106-AA4 (GEK-119558C)

GE Grid Solutions 650 Markland Street Markham, Ontario Canada L6C 0M1 Tel: +1 905 927 7070 Fax: +1 905 927 5098 Internet: http://www.GEGridSolutions.com

*1601-0106-AA4*

GE Multilin's Quality Management

System is registered to ISO

9001:2008

QMI # 005094

UL # A3775

7.2x. FlexLogic, FlexElement, FlexCurve, FlexAnalog, FlexInteger, FlexState, EnerVista,

CyberSentry, HardFiber, Multilin, and GE Multilin are trademarks or registered trademarks of GE Multilin Inc.

The contents of this manual are the property of GE Multilin Inc. This documentation is furnished on license and may not be reproduced in whole or in part without the permission of GE Multilin. The content of this manual is for informational use only and is subject to change without notice. Part number: 1601-0106-AA4 (April 2016)

TABLE OF CONTENTS

1. GETTING STARTED 1.1 IMPORTANT PROCEDURES

1.1.1 CAUTIONS AND WARNINGS ........................................................................... 1-1

1.1.2 INSPECTION PROCEDURE ............................................................................. 1-2

1.2 UR OVERVIEW

1.2.1 INTRODUCTION TO THE UR ........................................................................... 1-3

1.2.2 HARDWARE ARCHITECTURE......................................................................... 1-3

1.2.3 SOFTWARE ARCHITECTURE.......................................................................... 1-4

1.3 ENERVISTA UR SETUP SOFTWARE

1.3.1 SYSTEM REQUIREMENTS .............................................................................. 1-5

1.3.2 INSTALLATION.................................................................................................. 1-5

1.3.3 CONFIGURING THE F35 FOR SOFTWARE ACCESS .................................... 1-6

1.3.4 USING THE QUICK CONNECT FEATURE.......................................................1-9

1.3.5 CONNECTING TO THE F35 RELAY...............................................................1-14

1.3.6 SETTING UP CYBERSENTRY AND CHANGING DEFAULT PASSWORD ... 1-15

1.4 UR HARDWARE

1.4.1 MOUNTING AND WIRING............................................................................... 1-16

1.4.2 COMMUNICATIONS........................................................................................1-16

1.4.3 FACEPLATE DISPLAY....................................................................................1-16

1.5 USING THE RELAY

1.5.1 FACEPLATE KEYPAD..................................................................................... 1-17

1.5.2 MENU NAVIGATION ....................................................................................... 1-17

1.5.3 MENU HIERARCHY ........................................................................................1-17

1.5.4 RELAY ACTIVATION....................................................................................... 1-18

1.5.5 RELAY PASSWORDS.....................................................................................1-18

1.5.6 FLEXLOGIC CUSTOMIZATION ...................................................................... 1-18

1.5.7 COMMISSIONING ........................................................................................... 1-19

2. PRODUCT DESCRIPTION 2.1 INTRODUCTION

2.1.1 OVERVIEW........................................................................................................ 2-1

2.1.2 SECURITY ......................................................................................................... 2-2

2.1.3 IEC 870-5-103 PROTOCOL...............................................................................2-6

2.2 ORDER CODES

2.2.1 OVERVIEW........................................................................................................ 2-8

2.2.2 ORDER CODES WITH ENHANCED CT/VT MODULES................................... 2-8

2.2.3 ORDER CODES WITH PROCESS BUS MODULES ...................................... 2-11

2.2.4 REPLACEMENT MODULES ........................................................................... 2-14

2.3 SIGNAL PROCESSING

2.3.1 UR SIGNAL PROCESSING............................................................................. 2-16

2.4 SPECIFICATIONS

2.4.1 PROTECTION ELEMENTS ............................................................................. 2-18

2.4.2 USER-PROGRAMMABLE ELEMENTS...........................................................2-20

2.4.3 MONITORING.................................................................................................. 2-21

2.4.4 METERING ...................................................................................................... 2-21

2.4.5 INPUTS............................................................................................................2-22

2.4.6 POWER SUPPLY ............................................................................................ 2-23

2.4.7 OUTPUTS........................................................................................................2-23

2.4.8 COMMUNICATION PROTOCOLS ..................................................................2-25

2.4.9 INTER-RELAY COMMUNICATIONS............................................................... 2-25

2.4.10 ENVIRONMENTAL .......................................................................................... 2-26

2.4.11 TYPE TESTS ................................................................................................... 2-27

2.4.12 PRODUCTION TESTS ....................................................................................2-27

2.4.13 APPROVALS ................................................................................................... 2-28

2.4.14 MAINTENANCE ............................................................................................... 2-28

3. HARDWARE 3.1 DESCRIPTION

3.1.1 PANEL CUTOUT ............................................................................................... 3-1

3.1.2 REAR TERMINAL LAYOUT............................................................................... 3-7

GE Multilin F35 Multiple Feeder Protection System iii

TABLE OF CONTENTS

3.2 WIRING

3.2.1 TYPICAL WIRING ..............................................................................................3-8

3.2.2 DIELECTRIC STRENGTH..................................................................................3-9

3.2.3 CONTROL POWER............................................................................................3-9

3.2.4 CT/VT MODULES.............................................................................................3-10

3.2.5 PROCESS BUS MODULES .............................................................................3-12

3.2.6 CONTACT INPUTS AND OUTPUTS................................................................3-12

3.2.7 TRANSDUCER INPUTS/OUTPUTS.................................................................3-20

3.2.8 RS232 FACEPLATE PORT..............................................................................3-21

3.2.9 CPU COMMUNICATION PORTS.....................................................................3-22

3.2.10 IRIG-B...............................................................................................................3-24

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

3.3.1 DESCRIPTION .................................................................................................3-25

3.3.2 FIBER: LED AND ELED TRANSMITTERS ......................................................3-26

3.3.3 FIBER-LASER TRANSMITTERS .....................................................................3-27

3.3.4 G.703 INTERFACE...........................................................................................3-28

3.3.5 RS422 INTERFACE .........................................................................................3-31

3.3.6 RS422 AND FIBER INTERFACE .....................................................................3-33

3.3.7 G.703 AND FIBER INTERFACE ......................................................................3-33

3.3.8 IEEE C37.94 INTERFACE................................................................................3-34

3.3.9 C37.94SM INTERFACE ...................................................................................3-37

4. HUMAN INTERFACES 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE

4.1.1 INTRODUCTION ................................................................................................4-1

4.1.2 CREATING A SITE LIST ....................................................................................4-1

4.1.3 ENERVISTA UR SETUP OVERVIEW................................................................4-1

4.1.4 ENERVISTA UR SETUP MAIN WINDOW..........................................................4-3

4.2 EXTENDED ENERVISTA UR SETUP FEATURES

4.2.1 SETTINGS TEMPLATES ...................................................................................4-5

4.2.2 SECURING AND LOCKING FLEXLOGIC EQUATIONS....................................4-9

4.2.3 SETTINGS FILE TRACEABILITY.....................................................................4-11

4.3 FACEPLATE INTERFACE

4.3.1 FACEPLATE.....................................................................................................4-14

4.3.2 LED INDICATORS............................................................................................4-15

4.3.3 CUSTOM LABELING OF LEDS .......................................................................4-18

4.3.4 DISPLAY...........................................................................................................4-23

4.3.5 KEYPAD ...........................................................................................................4-23

4.3.6 BREAKER CONTROL ......................................................................................4-23

4.3.7 MENUS.............................................................................................................4-24

4.3.8 CHANGING SETTINGS ...................................................................................4-27

5. SETTINGS 5.1 OVERVIEW

5.1.1 SETTINGS MENU ..............................................................................................5-1

5.1.2 INTRODUCTION TO ELEMENTS......................................................................5-4

5.1.3 INTRODUCTION TO AC SOURCES..................................................................5-5

5.2 PRODUCT SETUP

5.2.1 SECURITY..........................................................................................................5-8

5.2.2 DISPLAY PROPERTIES ..................................................................................5-24

5.2.3 CLEAR RELAY RECORDS..............................................................................5-25

5.2.4 COMMUNICATIONS ........................................................................................5-27

5.2.5 MODBUS USER MAP ......................................................................................5-65

5.2.6 REAL TIME CLOCK .........................................................................................5-65

5.2.7 FAULT REPORTS............................................................................................5-70

5.2.8 OSCILLOGRAPHY...........................................................................................5-72

5.2.9 DATA LOGGER................................................................................................5-74

5.2.10 DEMAND ..........................................................................................................5-75

5.2.11 USER-PROGRAMMABLE LEDS .....................................................................5-76

5.2.12 USER-PROGRAMMABLE SELF TESTS .........................................................5-80

5.2.13 CONTROL PUSHBUTTONS ............................................................................5-81

5.2.14 USER-PROGRAMMABLE PUSHBUTTONS....................................................5-83

iv F35 Multiple Feeder Protection System GE Multilin

TABLE OF CONTENTS

5.2.15 FLEX STATE PARAMETERS.......................................................................... 5-89

5.2.16 USER-DEFINABLE DISPLAYS ....................................................................... 5-89

5.2.17 DIRECT INPUTS/OUTPUTS ...........................................................................5-92

5.2.18 TELEPROTECTION.........................................................................................5-99

5.2.19 INSTALLATION.............................................................................................. 5-100

5.3 REMOTE RESOURCES

5.3.1 REMOTE RESOURCES CONFIGURATION.................................................5-101

5.4 SYSTEM SETUP

5.4.1 AC INPUTS....................................................................................................5-102

5.4.2 POWER SYSTEM.......................................................................................... 5-103

5.4.3 SIGNAL SOURCES ....................................................................................... 5-104

5.4.4 BREAKERS.................................................................................................... 5-107

5.4.5 DISCONNECT SWITCHES ........................................................................... 5-111

5.4.6 FLEXCURVES ............................................................................................... 5-114

5.5 FLEXLOGIC

5.5.1 INTRODUCTION TO FLEXLOGIC ................................................................ 5-121

5.5.2 FLEXLOGIC RULES...................................................................................... 5-130

5.5.3 FLEXLOGIC EVALUATION ........................................................................... 5-130

5.5.4 FLEXLOGIC EXAMPLE ................................................................................. 5-131

5.5.5 FLEXLOGIC EQUATION EDITOR................................................................. 5-135

5.5.6 FLEXLOGIC TIMERS .................................................................................... 5-135

5.5.7 FLEXELEMENTS........................................................................................... 5-136

5.5.8 NON-VOLATILE LATCHES ........................................................................... 5-141

5.6 GROUPED ELEMENTS

5.6.1 OVERVIEW.................................................................................................... 5-142

5.6.2 SETTING GROUP ......................................................................................... 5-142

5.6.3 PHASE CURRENT ........................................................................................5-142

5.6.4 NEUTRAL CURRENT...................................................................................5-150

5.6.5 WATTMETRIC GROUND FAULT.................................................................. 5-153

5.6.6 GROUND CURRENT..................................................................................... 5-157

5.6.7 NEGATIVE SEQUENCE CURRENT .............................................................5-159

5.6.8 VOLTAGE ELEMENTS.................................................................................. 5-163

5.7 CONTROL ELEMENTS

5.7.1 OVERVIEW.................................................................................................... 5-169

5.7.2 TRIP BUS....................................................................................................... 5-169

5.7.3 SETTING GROUPS ....................................................................................... 5-171

5.7.4 SELECTOR SWITCH.....................................................................................5-173

5.7.5 UNDERFREQUENCY (ANSI 81U) ................................................................ 5-179

5.7.6 AUTORECLOSE (ANSI 79) ...........................................................................5-180

5.7.7 DIGITAL ELEMENTS..................................................................................... 5-186

5.7.8 DIGITAL COUNTERS .................................................................................... 5-189

5.7.9 8-BIT SWITCHES .......................................................................................... 5-191

5.7.10 MONITORING ELEMENTS ........................................................................... 5-193

5.7.11 PID REGULATOR.......................................................................................... 5-208

5.8 INPUTS AND OUTPUTS

5.8.1 CONTACT INPUTS........................................................................................5-211

5.8.2 VIRTUAL INPUTS.......................................................................................... 5-213

5.8.3 CONTACT OUTPUTS.................................................................................... 5-214

5.8.4 VIRTUAL OUTPUTS...................................................................................... 5-217

5.8.5 REMOTE DEVICES.......................................................................................5-217

5.8.6 REMOTE INPUTS..........................................................................................5-219

5.8.7 REMOTE DOUBLE-POINT STATUS INPUTS ..............................................5-220

5.8.8 REMOTE OUTPUTS...................................................................................... 5-220

5.8.9 RESETTING................................................................................................... 5-221

5.8.10 DIRECT INPUTS AND OUTPUTS................................................................. 5-222

5.8.11 TELEPROTECTION INPUTS AND OUTPUTS..............................................5-225

5.8.12 IEC 61850 GOOSE ANALOGS...................................................................... 5-227

5.8.13 IEC 61850 GOOSE INTEGERS..................................................................... 5-228

5.9 TRANSDUCER INPUTS AND OUTPUTS

5.9.1 DCMA INPUTS .............................................................................................. 5-229

5.9.2 RTD INPUTS..................................................................................................5-230

5.9.3 DCMA OUTPUTS .......................................................................................... 5-232

GE Multilin F35 Multiple Feeder Protection System v

TABLE OF CONTENTS

5.10 TESTING

5.10.1 TEST MODE...................................................................................................5-235

5.10.2 FORCE CONTACT INPUTS...........................................................................5-236

5.10.3 FORCE CONTACT OUTPUTS.......................................................................5-237

6. ACTUAL VALUES 6.1 OVERVIEW

6.1.1 ACTUAL VALUES MENU...................................................................................6-1

6.2 STATUS

6.2.1 CONTACT INPUTS ............................................................................................6-4

6.2.2 VIRTUAL INPUTS ..............................................................................................6-4

6.2.3 REMOTE INPUTS ..............................................................................................6-4

6.2.4 REMOTE DOUBLE-POINT STATUS INPUTS...................................................6-5

6.2.5 TELEPROTECTION INPUTS.............................................................................6-5

6.2.6 CONTACT OUTPUTS ........................................................................................6-5

6.2.7 VIRTUAL OUTPUTS ..........................................................................................6-6

6.2.8 AUTORECLOSE.................................................................................................6-6

6.2.9 REMOTE DEVICES............................................................................................6-6

6.2.10 DIGITAL COUNTERS.........................................................................................6-7

6.2.11 SELECTOR SWITCHES ....................................................................................6-7

6.2.12 FLEX STATES....................................................................................................6-8

6.2.13 ETHERNET ........................................................................................................6-8

6.2.14 REAL TIME CLOCK SYNCHRONIZING ............................................................6-8

6.2.15 DIRECT INPUTS ................................................................................................6-9

6.2.16 DIRECT DEVICES STATUS ............................................................................6-10

6.2.17 IEC 61850 GOOSE INTEGERS .......................................................................6-10

6.2.18 EGD PROTOCOL STATUS..............................................................................6-10

6.2.19 TELEPROTECTION CHANNEL TESTS...........................................................6-11

6.2.20 INCIPIENT FAULT DETECTOR.......................................................................6-11

6.2.21 REMAINING CONNECTION STATUS.............................................................6-12

6.2.22 PARALLEL REDUNDANCY PROTOCOL (PRP) .............................................6-12

6.3 METERING

6.3.1 METERING CONVENTIONS ...........................................................................6-14

6.3.2 SOURCES ........................................................................................................6-17

6.3.3 TRACKING FREQUENCY................................................................................6-23

6.3.4 FLEXELEMENTS .............................................................................................6-24

6.3.5 IEC 61580 GOOSE ANALOG VALUES ...........................................................6-24

6.3.6 WATTMETRIC GROUND FAULT.....................................................................6-25

6.3.7 TRANSDUCER INPUTS/OUTPUTS.................................................................6-25

6.4 RECORDS

6.4.1 FAULT REPORTS............................................................................................6-26

6.4.2 EVENT RECORDS...........................................................................................6-26

6.4.3 OSCILLOGRAPHY...........................................................................................6-27

6.4.4 DATA LOGGER................................................................................................6-27

6.4.5 BREAKER MAINTENANCE .............................................................................6-28

6.5 PRODUCT INFORMATION

6.5.1 MODEL INFORMATION...................................................................................6-29

6.5.2 FIRMWARE REVISIONS..................................................................................6-29

7. COMMANDS AND TARGETS

7.1 COMMANDS

7.1.1 COMMANDS MENU...........................................................................................7-1

7.1.2 VIRTUAL INPUTS ..............................................................................................7-1

7.1.3 CLEAR RECORDS.............................................................................................7-2

7.1.4 SET DATE AND TIME........................................................................................7-2

7.1.5 RELAY MAINTENANCE.....................................................................................7-3

7.1.6 SECURITY..........................................................................................................7-4

7.1.7 TARGETS MENU ...............................................................................................7-4

7.1.8 TARGET MESSAGES........................................................................................7-4

7.1.9 RELAY SELF-TESTS .........................................................................................7-5

vi F35 Multiple Feeder Protection System GE Multilin

TABLE OF CONTENTS

8. THEORY OF OPERATION 8.1 FAULT LOCATOR

8.1.1 FAULT TYPE DETERMINATION....................................................................... 8-1

9. COMMISSIONING 9.1 TESTING

9.1.1 TESTING UNDERFREQUENCY ELEMENTS................................................... 9-1

10. MAINTENANCE 10.1 MODULES

10.1.1 REPLACE A MODULE.....................................................................................10-1

10.2 BATTERIES

10.2.1 REPLACE BATTERY....................................................................................... 10-3

10.2.2 DISPOSE OF BATTERY..................................................................................10-5

10.3 UNINSTALL AND CLEAR FILES AND DATA

10.3.1 UNINSTALL AND CLEAR FILES AND DATA.................................................. 10-8

10.4 REPAIRS

10.4.1 REPAIRS ......................................................................................................... 10-9

10.5 STORAGE

10.5.1 STORAGE...................................................................................................... 10-10

10.6 DISPOSAL

10.6.1 DISPOSAL ..................................................................................................... 10-11

A. FLEXANALOG AND

FLEXINTEGER PARAMETERS

B. MODBUS

COMMUNICATIONS

C. IEC 61850

COMMUNICATIONS

A.1 PARAMETER LISTS

A.1.1 FLEXANALOG ITEMS .......................................................................................A-1

A.1.2 FLEXINTEGER ITEMS ....................................................................................A-27

B.1 MODBUS RTU PROTOCOL

B.1.1 INTRODUCTION................................................................................................B-1

B.1.2 PHYSICAL LAYER.............................................................................................B-1

B.1.3 DATA LINK LAYER............................................................................................B-1

B.1.4 MODBUS RTU CRC-16 ALGORITHM...............................................................B-2

B.2 MODBUS FUNCTION CODES

B.2.1 SUPPORTED FUNCTION CODES ...................................................................B-4

B.2.2 READ ACTUAL VALUES OR SETTINGS (FUNCTION CODE 03/04H) ...........B-4

B.2.3 EXECUTE OPERATION (FUNCTION CODE 05H) ...........................................B-5

B.2.4 STORE SINGLE SETTING (FUNCTION CODE 06H).......................................B-5

B.2.5 STORE MULTIPLE SETTINGS (FUNCTION CODE 10H) ................................B-6

B.2.6 EXCEPTION RESPONSES...............................................................................B-6

B.3 FILE TRANSFERS

B.3.1 OBTAINING RELAY FILES VIA MODBUS........................................................B-7

B.4 MEMORY MAPPING

B.4.1 MODBUS MEMORY MAP .................................................................................B-9

B.4.2 DATA FORMATS.............................................................................................B-73

C.1 OVERVIEW

C.1.1 INTRODUCTION................................................................................................C-1

C.1.2 COMMUNICATION PROFILES.........................................................................C-1

C.1.3 FILE TRANSFER BY IEC 61850 .......................................................................C-2

C.2 SERVER DATA ORGANIZATION

GE Multilin F35 Multiple Feeder Protection System vii

TABLE OF CONTENTS

C.2.1 OVERVIEW .......................................................................................................C-3

C.2.2 GGIO1: DIGITAL STATUS VALUES.................................................................C-3

C.2.3 GGIO2: DIGITAL CONTROL VALUES..............................................................C-3

C.2.4 GGIO3: DIGITAL STATUS AND ANALOG VALUES FROM GOOSE DATA ....C-3

C.2.5 GGIO4: GENERIC ANALOG MEASURED VALUES.........................................C-3

C.2.6 MMXU: ANALOG MEASURED VALUES ..........................................................C-4

C.2.7 PROTECTION AND OTHER LOGICAL NODES............................................... C-4

C.3 SERVER FEATURES AND CONFIGURATION

C.3.1 BUFFERED/UNBUFFERED REPORTING........................................................C-6

C.3.2 FILE TRANSFER...............................................................................................C-6

C.3.3 TIMESTAMPS AND SCANNING.......................................................................C-6

C.3.4 LOGICAL DEVICE NAME .................................................................................C-6

C.3.5 LOCATION ........................................................................................................ C-6

C.3.6 LOGICAL NODE NAME PREFIXES.................................................................. C-7

C.3.7 CONNECTION TIMING.....................................................................................C-7

C.3.8 NON-IEC 61850 DATA......................................................................................C-7

C.3.9 COMMUNICATION SOFTWARE UTILITIES..................................................... C-7

C.4 GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE

C.4.1 OVERVIEW .......................................................................................................C-8

C.4.2 GSSE CONFIGURATION..................................................................................C-8

C.4.3 FIXED GOOSE..................................................................................................C-8

C.4.4 CONFIGURABLE GOOSE ................................................................................ C-8

C.4.5 ETHERNET MAC ADDRESS FOR GSSE/GOOSE ........................................C-11

C.4.6 GSSE ID AND GOOSE ID SETTINGS............................................................C-11

C.5 IEC 61850 IMPLEMENTATION VIA ENERVISTA UR SETUP

C.5.1 OVERVIEW .....................................................................................................C-12

C.5.2 CONFIGURING IEC 61850 SETTINGS ..........................................................C-13

C.5.3 ABOUT ICD FILES ..........................................................................................C-14

C.5.4 CREATING AN ICD FILE WITH ENERVISTA UR SETUP..............................C-18

C.5.5 ABOUT SCD FILES.........................................................................................C-18

C.5.6 IMPORTING AN SCD FILE WITH ENERVISTA UR SETUP...........................C-21

C.6 ACSI CONFORMANCE

C.6.1 ACSI BASIC CONFORMANCE STATEMENT ................................................C-23

C.6.2 ACSI MODELS CONFORMANCE STATEMENT............................................C-23

C.6.3 ACSI SERVICES CONFORMANCE STATEMENT.........................................C-24

C.7 LOGICAL NODES

C.7.1 LOGICAL NODES TABLE ...............................................................................C-27

D. IEC 60870-5-103

COMMUNICATIONS

D.1 IEC 60870-5-103

D.1.1 OVERVIEW .......................................................................................................D-1

D.1.2 FACTOR AND OFFSET CALCULATION TO TRANSMIT MEASURAND......... D-1

D.1.3 INTEROPERABILITY DOCUMENT...................................................................D-2

E. IEC 60870-5-104 COMMS. E.1 IEC 60870-5-104 PROTOCOL

E.1.1 INTEROPERABILITY DOCUMENT................................................................... E-1

E.1.2 POINTS LIST..................................................................................................... E-9

F. DNP COMMUNICATIONS F.1 DEVICE PROFILE DOCUMENT

F.1.1 DNP V3.00 DEVICE PROFILE .......................................................................... F-1

F.1.2 IMPLEMENTATION TABLE .............................................................................. F-4

F.2 DNP POINT LISTS

F.2.1 BINARY INPUT POINTS ................................................................................... F-8

F.2.2 BINARY AND CONTROL RELAY OUTPUT...................................................... F-9

F.2.3 COUNTERS..................................................................................................... F-10

F.2.4 ANALOG INPUTS............................................................................................ F-11

viii F35 Multiple Feeder Protection System GE Multilin

TABLE OF CONTENTS

G. RADIUS SERVER G.1 RADIUS SERVER CONFIGURATION

G.1.1 RADIUS SERVER CONFIGURATION.............................................................. G-1

H. MISCELLANEOUS H.1 CHANGE NOTES

H.1.1 REVISION HISTORY .........................................................................................H-1

H.1.2 CHANGES TO THE MANUAL ...........................................................................H-2

H.2 ABBREVIATIONS

H.2.1 STANDARD ABBREVIATIONS .........................................................................H-5

H.3 WARRANTY

H.3.1 GE MULTILIN WARRANTY ...............................................................................H-7

GE Multilin F35 Multiple Feeder Protection System ix

TABLE OF CONTENTS

x F35 Multiple Feeder Protection System GE Multilin

1 GETTING STARTED 1.1 IMPORTANT PROCEDURES

DANGER

WARNING

CAUTION

NOTICE

DANGER

CAUTION

1 GETTING STARTED 1.1IMPORTANT PROCEDURES

Use this chapter for initial setup of your new F35 Multiple Feeder Protection System.

1.1.1 CAUTIONS AND WARNINGS

Before attempting to install or use the device, review all safety indicators in this document to help prevent injury, equipment damage, or downtime.

The following safety and equipment symbols are used in this document.

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

Indicates practices not related to personal injury.

a) GENERAL CAUTIONS AND WARNINGS

The following general safety precautions and warnings apply.

Ensure that all connections to the product are correct so as to avoid accidental risk of shock and/or fire, for example such as can arise from high voltage connected to low voltage terminals.

Follow the requirements of this manual, including adequate wiring size and type, terminal torque settings, voltage, current magnitudes applied, and adequate isolation/clearance in external wiring from high to low voltage circuits.

Use the device only for its intended purpose and application.

Ensure that all ground paths are uncompromised for safety purposes during device operation and service.

Ensure that the control power applied to the device, the AC current, and voltage input match the ratings specified on the relay nameplate. Do not apply current or voltage in excess of the specified limits.

Only qualified personnel are to operate the device. Such personnel must be thoroughly familiar with all safety cautions and warnings in this manual and with applicable country, regional, utility, and plant safety regulations.

Hazardous voltages can exist in the power supply and at the device connection to current transformers, voltage transformers, control, and test circuit terminals. Make sure all sources of such voltages are isolated prior to attempting work on the device.

Hazardous voltages can exist when opening the secondary circuits of live current transformers. Make sure that current transformer secondary circuits are shorted out before making or removing any connection to the current transformer (CT) input terminals of the device.

For tests with secondary test equipment, ensure that no other sources of voltages or currents are connected to such equipment and that trip and close commands to the circuit breakers or other switching apparatus are isolated, unless this is required by the test procedure and is specified by appropriate utility/plant procedure.

When the device is used to control primary equipment, such as circuit breakers, isolators, and other switching apparatus, all control circuits from the device to the primary equipment must be isolated while personnel are working on or around this primary equipment to prevent any inadvertent command from this device.

Use an external disconnect to isolate the mains voltage supply.

Personal safety can be affected if the product is physically modified by the end user. Modifications to the product outside of recommended wiring configuration, hardware, or programming boundaries is not recommended enduse practice. Product disassembly and repairs are not permitted. All service needs to be conducted by the factory.

LED transmitters are classified as IEC 60825-1 Accessible Emission Limit (AEL) Class 1M. Class 1M devices are considered safe to the unaided eye. Do not view directly with optical instruments.

GE Multilin F35 Multiple Feeder Protection System 1-1

1.1 IMPORTANT PROCEDURES 1 GETTING STARTED

832772A3.CDR

Model: Mods: Wiring Diagram: Inst. Manual: Serial Number: Firmware: Mfg. Date: PO Num: Item Num:

F35D00HCHF8AH6AM6BP8BX7A NONE See manual 1601-0106 AAIC07000515 A09MA521.000 NOV 12, 2012

600001234.56

Control Power: Contact Inputs: Contact Outputs:

125-250 V — 0.7A/100-240, 50/60Hz, 0.7A 300 V ---- Max 10mA Refer to Instruction Manual

RATINGS:

F35

Multiple Feeder Management Relay

GE Multilin

LISTED

52TL

IND.CONT. EQ.

E83849

This product is rated to Class A emissions levels and is to be used in Utility, Substation Industrial environments. Not to be used near electronic devices rated for Class B levels.

1.1.2 INSPECTION PROCEDURE

1. Open the relay packaging and inspect the unit for physical damage.

2. View the rear nameplate and verify that the correct model has been ordered and delivered. The model number is at the top right.

Figure 1–1: REAR NAMEPLATE (EXAMPLE)

3. Ensure that the following items are included:

• Instruction manual (if ordered)

• GE EnerVista™ DVD (includes the EnerVista UR Setup software and manuals in PDF format)

• Mounting screws

4. If there is any noticeable physical damage, or any of the contents listed are missing, contact GE Grid Solutions as follows.

GE GRID SOLUTIONS CONTACT INFORMATION AND CALL CENTER FOR PRODUCT SUPPORT:

GE Grid Solutions 650 Markland Street Markham, Ontario Canada L6C 0M1

TELEPHONE: Worldwide +1 905 927 7070

Europe/Middle East/Africa +34 94 485 88 54 North America toll-free 1 800 547 8629

FAX: +1 905 927 5098 E-MAIL: Worldwide multilin.tech@ge.com

Europe multilin.tech.euro@ge.com

HOME PAGE: http://www.gegridsolutions.com/multilin

For updates to the instruction manual, firmware, and software, visit the GE Grid Solutions website.

1-2 F35 Multiple Feeder Protection System GE Multilin

1 GETTING STARTED 1.2 UR OVERVIEW

827822A3.CDR

Input elements

LAN

Programming

device

Operator interface

Contact inputs Contact outputs

Virtual inputs

Virtual outputs

Analog inputs

Analog outputs

CT inputs

VT inputs

Input

status

table

Output

status

table

Pickup Dropout Operate

Protective elements

Logic Gates

Remote outputs

- IEC 61850

CPU module

Output elements

Remote inputs

Direct inputs Direct outputs

1.2UR OVERVIEW 1.2.1 INTRODUCTION TO THE UR

The GE Universal Relay (UR) series is a new generation of digital, modular, and multifunction equipment that is easily incorporated into automation systems, at both the station and enterprise levels.

1.2.2 HARDWARE ARCHITECTURE

a) UR BASIC DESIGN

The UR is a digital-based device containing a central processing unit (CPU) that handles multiple types of input and output signals. The UR device can communicate over a local area network (LAN) with an operator interface, a programming device, or another UR device.

Figure 1–2: UR BLOCK DIAGRAM

The CPU module contains firmware that provides protection elements in the form of logic algorithms, as well as programmable logic gates, timers, and latches for control features.

Input elements accept a variety of analog or digital signals from the field. The UR isolates and converts these signals into logic signals used by the relay.

Output elements convert and isolate the logic signals generated by the relay into digital or analog signals that are used to control field devices.

The unit and software are backwards-compatible with UR devices.

b) UR SIGNAL TYPES

The contact inputs and outputs are digital signals associated with connections to hard-wired contacts. Both ‘wet’ and ‘dry’ contacts are supported.

The virtual inputs and outputs are digital signals associated with UR-series internal logic signals. Virtual inputs include signals generated by the local user interface. The virtual outputs are outputs of FlexLogic™ equations used to customize the device. Virtual outputs can also serve as virtual inputs to FlexLogic equations.

The analog inputs and outputs are signals that are associated with transducers, such as Resistance Temperature Detec- tors (RTDs).

The CT and VT inputs are analog current transformer and voltage transformer signals used to monitor AC power lines. The UR-series relays support 1 A and 5 A CTs.

The remote inputs and outputs provide a means of sharing digital point state information between remote UR-series devices. The remote outputs interface to the remote inputs of other UR-series devices. Remote outputs are FlexLogic operands inserted into IEC 61850 GSSE and GOOSE messages.

GE Multilin F35 Multiple Feeder Protection System 1-3

1.2 UR OVERVIEW 1 GETTING STARTED

The direct inputs and outputs provide a means of sharing digital point states between a number of UR-series intelligent electronic devices (IEDs) over dedicated fiber, RS422, or G.703 interface. No switching equipment is required as the IEDs

are connected directly in a ring or redundant (dual) ring configuration. This feature is optimized for speed and intended for pilot-aided schemes, distributed logic applications, or the extension of the input/output capabilities of a single relay chassis.

1.2.3 SOFTWARE ARCHITECTURE

Firmware is the software embedded in the relay in functional modules that can be installed in any relay as required. This is achieved with object-oriented design and programming (OOD/OOP) techniques.

Object-oriented techniques involve the use of objects and classes. An object is defined as “a logical entity that contains both data and code that manipulates data.” A class is the generalized form of similar objects. By using this approach, one can create a protection class with the protection elements as objects of the class, such as time overcurrent, instantaneous overcurrent, current differential, undervoltage, overvoltage, underfrequency, and distance. These objects represent completely self-contained software modules. The same object-class concept can be used for metering, input/output control, software interface, communications, or any functional entity in the system.

Employing OOD/OOP in the software architecture of the F35 achieves the same features as the hardware architecture: modularity, scalability, and flexibility. The application software for any UR-series device (for example, feeder protection, transformer protection, distance protection) is constructed by combining objects from the various functional classes. This results in a common interface across the UR series.

1-4 F35 Multiple Feeder Protection System GE Multilin

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

1.3ENERVISTA UR SETUP SOFTWARE 1.3.1 SYSTEM REQUIREMENTS

The relay front panel or the EnerVista UR Setup software can be used to communicate with the relay. The software interface is the preferred method to edit settings and view actual values because the computer monitor can display more information.

The minimum system requirements for the EnerVista UR Setup software are as follows:

• Pentium 4 (Core Duo recommended)

• Windows XP with Service Pack 2 (Service Pack 3 recommended), Windows 7, or Windows Server 2008 Release 2

64-bit

• 1 GB of RAM (2 GB recommended)

• 500 MB free hard drive space (1 GB recommended)

• 1024 x 768 display (1280 x 800 recommended)

•Serial port

• Ethernet port of the same type as one of the UR CPU ports or a LAN connection to the UR

• Internet access or a DVD drive The following qualified modems have been tested to be compatible with the F35 and the EnerVista UR Setup software:

• US Robotics external 56K FaxModem 5686

• US Robotics external Sportster 56K X2

• PCTEL 2304WT V.92 MDC internal modem

1.3.2 INSTALLATION

After ensuring that the requirements for using EnerVista UR Setup software are met, install the software from the GE EnerVista DVD. Or download the UR EnerVista software from http://www.gegridsolutions.com/multilin

To install the UR EnerVista software from the DVD:

1. Insert the GE EnerVista DVD into the DVD drive of your computer.

2. Click the Install Now button and follow the instructions.

3. When installation is complete, start the EnerVista Launchpad application.

4. Click the IED Setup section of the Launch Pad window.

Figure 1–3: ADDING A UR DEVICE IN LAUNCHPAD WINDOW

5. In the EnerVista Launch Pad window, click the Add Product button and select the appropriate product as follows.

Select the Web option to ensure the most recent software release, or select CD if you do not have an Internet connec-

and install it.

GE Multilin F35 Multiple Feeder Protection System 1-5

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

tion, then click the Add Now button to list software items for the product. EnerVista Launchpad obtains the software from the Internet or DVD and automatically starts the installation program.

Figure 1–4: IDENTIFYING THE UR DEVICE TYPE

6. Select the complete path, including the new directory name, where the EnerVista UR Setup software is to be installed.

7. Click the Next button to begin the installation. The files are installed in the directory indicated, and the installation program automatically creates icons and adds an entry to the Windows start menu.

8. Click Finish to complete the installation. The UR device is added to the list of installed intelligent electronic devices (IEDs) in the EnerVista Launchpad window, as shown.

Figure 1–5: UR DEVICE ADDED TO LAUNCHPAD WINDOW

1.3.3 CONFIGURING THE F35 FOR SOFTWARE ACCESS

a) OVERVIEW

You connect remotely to the F35 through the rear RS485 or Ethernet port with a computer running the EnerVista UR Setup software. The F35 can also be accessed locally with a computer through the front panel RS232 port or the rear Ethernet port using the Quick Connect feature.

• To configure the F35 for remote access via the rear RS485 port, see the Configuring Serial Communications section.

• To configure the F35 for remote access via the rear Ethernet port, see the Configuring Ethernet Communications section.

• To configure the F35 for local access with a computer through either the front RS232 port or rear Ethernet port, see the Using the Quick Connect Feature section.

1-6 F35 Multiple Feeder Protection System GE Multilin

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

b) CONFIGURING SERIAL COMMUNICATIONS

A computer with an RS232 port and a serial cable is required. To use the RS485 port at the back of the relay, a GE Multilin F485 converter (or compatible RS232-to-RS485 converter) is required. See the F485 instruction manual for details.

1. Connect the computer to the F485 and the F485 to the RS485 terminal on the back of the UR device, or connect

directly the computer to the RS232 port on the front of the relay.

2. In the EnerVista Launchpad software on the computer, select the UR device to start the software.

3. Click the Device Setup button to open the Device Setup window, and click the Add Site button to define a new site.

4. Enter a site name in the Site Name field. Optionally add a short description of the site along with the display order of

devices defined for the site. This example uses “Location 1” as the site name. When done, click the OK button. The new site appears in the upper-left list in the EnerVista UR Setup window.

5. Click the Device Setup button, then select the new site to re-open the Device Setup window.

6. Click the Add Device button to define the new device.

7. Enter a name in the "Device Name” field and a description (optional) of the site.

8. Select “Serial” from the Interface drop-down list. This displays a number of interface parameters that must be entered

for serial communications.

Figure 1–6: CONFIGURING SERIAL COMMUNICATIONS

9. Enter the COM port used by the computer, the baud rate, and parity settings from the front panel

SETUP  COMMUNICATIONS  SERIAL PORTS menu, and the relay slave address setting from the front panel SETTINGS

 PRODUCT SETUP  COMMUNICATIONS  MODBUS PROTOCOL  MODBUS SLAVE ADDRESS menu in their respective

fields.

10. Click the Read Order Code button to connect to the F35 device and upload the order code. If a communications error

occurs, ensure that the EnerVista UR Setup serial communications values entered in the previous step correspond to the relay setting values.

11. Click the OK button when the relay order code has been received. The new device is added to the Site List window (or

Online window) located in the top left corner of the main EnerVista UR Setup window.

The device has now been configured for RS232 communications. Proceed to the Connecting to the F35 section to begin communication.

GE Multilin F35 Multiple Feeder Protection System 1-7

SETTINGS  PRODUCT

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

c) CONFIGURING ETHERNET COMMUNICATIONS

Before starting, verify that the Ethernet network cable is properly connected to the Ethernet port on the back of the relay. To

setup the relay for Ethernet communications, you define a Site, then add the relay as a Device at that site.The computer and UR device must be on the same subnet.

12. Select the “UR” device from the EnerVista Launchpad to start EnerVista UR Setup.

13. Click the Device Setup button to open the Device Setup window, then click the Add Site button to define a new site.

14. Enter the desired site name in the “Site Name” field. If desired, a short description of site can also be entered along with the display order of devices defined for the site. In this example, we use “Location 2” as the site name. Click the OK button when complete.

15. The new site appears in the upper-left list in the EnerVista UR Setup window. Click the Device Setup button then select the new site to re-open the Device Setup window.

16. Click the Add Device button to define the new device.

17. Enter the desired name in the “Device Name” field and a description (optional) of the site.

18. Select “Ethernet” from the Interface drop-down list. This displays a number of interface parameters that must be entered for proper Ethernet functionality.

Figure 1–7: CONFIGURING ETHERNET COMMUNICATIONS

19. Enter the relay IP address specified in the front panel

WORK

 IP ADDRESS in the “IP Address” field.

20. Enter the relay slave address and Modbus port address values from the respective settings in the front panel

 PRODUCT SETUP  COMMUNICATIONS  MODBUS PROTOCOL menu.

21. Click the Read Order Code button to connect to the F35 device and upload the order code. If an communications error occurs, ensure that the three EnerVista UR Setup values entered in the previous steps correspond to the relay setting values.

22. Click OK when the relay order code has been received. The new device is added to the Site List window (or Online window) located in the top left corner of the main EnerVista UR Setup window.

The Site Device has now been configured for Ethernet communications. Proceed to the Connecting to the F35 section to begin communications.

1-8 F35 Multiple Feeder Protection System GE Multilin

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  NET-

SETTINGS

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

842799A1.CDR

END 1 END 2 Pin Wire color Diagram Pin Wire color Diagram

1 White/orange 1 White/green 2 Orange 2 Green

3 White/green 3 White/orange 4 Blue 4 Blue 5 White/blue 5 White/blue 6 Green 6 Orange 7 White/brown 7 White/brown 8 Brown 8 Brown

1.3.4 USING THE QUICK CONNECT FEATURE

a) USING QUICK CONNECT VIA THE FRONT PANEL RS232 PORT

Before starting, verify that the serial cable is properly connected from the computer to the front panel RS232 port with a straight-through 9-pin to 9-pin RS232 cable.

1. Verify that the latest version of the EnerVista UR Setup software is installed (available from the GE EnerVista CD or

online from http://www.gegridsolutions.com/multilin

). See the Software Installation section if not already installed.

2. Select the “UR” device from the EnerVista Launchpad to start EnerVista UR Setup.

3. Click the Quick Connect button to open the Quick Connect dialog box.

4. Select the Serial interface and the correct COM Port, then click Connect.

5. The EnerVista UR Setup software creates a site named “Quick Connect” with a corresponding device also named

“Quick Connect” and displays them at the upper-left of the screen. Expand the sections to view data directly from the F35 device.

Each time that the EnerVista UR Setup software is initialized, click the Quick Connect button to establish direct communications to the F35 device. This ensures that configuration of the EnerVista UR Setup software matches the F35 model number.

b) USING QUICK CONNECT VIA THE REAR ETHERNET PORTS

To use the Quick Connect feature to access the F35 from a computer through Ethernet, first assign an IP address to the relay from the front panel keyboard.

1. Press the MENU key until the SETTINGS menu displays.

2. Navigate to the

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting.

3. Enter an IP address, for example “1.1.1.1,” and select the ENTER key to save the value.

4. In the same menu, select the

SUBNET IP MASK setting.

5. Enter a subnet IP address, for example “255.0.0.0,” and press the ENTER key to save the value. Next, use an Ethernet cross-over cable to connect the computer to the rear Ethernet port. In case you need it, the figure

shows the pinout for an Ethernet cross-over cable.

Figure 1–8: ETHERNET CROSS-OVER CABLE PIN LAYOUT

Now, assign the computer an IP address compatible with the relay’s IP address.

GE Multilin F35 Multiple Feeder Protection System 1-9

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

1. From the Windows desktop, right-click the My Network Places icon and select Properties to open the network connections window.

2. Right-click the Local Area Connection icon and select Properties.

3. Select the Internet Protocol (TCP/IP) item from the list, and click the Properties button.

4. Click the “Use the following IP address” box.

1-10 F35 Multiple Feeder Protection System GE Multilin

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

5. Enter an IP address with the first three numbers the same as the IP address of the F35 relay and the last number dif-

ferent (in this example, 1.1.1.2).

6. Enter a subnet mask equal to the one set in the F35 (in this example, 255.0.0.0).

7. Click the OK button to save the values. Before continuing, test the Ethernet connection.

1. Open a Windows console window by selecting Start > Run from the Windows Start menu and typing “cmd”.

2. Type the following command, substituting the IP address of 1.1.1.1 with yours:

C:\WINNT>ping 1.1.1.1

3. If the connection is successful, the system returns four replies similar to the following:

Pinging 1.1.1.1 with 32 bytes of data:

Reply from 1.1.1.1: bytes=32 time<10ms TTL=255 Reply from 1.1.1.1: bytes=32 time<10ms TTL=255 Reply from 1.1.1.1: bytes=32 time<10ms TTL=255 Reply from 1.1.1.1: bytes=32 time<10ms TTL=255

Ping statistics for 1.1.1.1:

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip time in milliseconds:

Minimum = 0ms, Maximum = 0ms, Average = 0 ms

4. Note that the values for time and TTL vary depending on local network configuration.

5. If the following sequence of messages appears when entering the C:\WINNT>ping 1.1.1.1 command:

Pinging 1.1.1.1 with 32 bytes of data:

Request timed out. Request timed out. Request timed out. Request timed out.

Ping statistics for 1.1.1.1:

Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

Approximate round trip time in milliseconds:

Minimum = 0ms, Maximum = 0ms, Average = 0 ms

Pinging 1.1.1.1 with 32 bytes of data:

verify the physical connection between the F35 and the computer, and double-check the programmed IP address in the PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting, then repeat step 2.

6. If the following sequence of messages appears when entering the C:\WINNT>ping 1.1.1.1 command:

Pinging 1.1.1.1 with 32 bytes of data:

Hardware error. Hardware error. Hardware error. Hardware error.

Ping statistics for 1.1.1.1:

Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

Approximate round trip time in milliseconds:

Minimum = 0ms, Maximum = 0ms, Average = 0 ms

Pinging 1.1.1.1 with 32 bytes of data:

verify the physical connection between the F35 and the computer, and double-check the programmed IP address in

PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting, then repeat step 2.

the

7. If the following sequence of messages appears when entering the

C:\WINNT>ping 1.1.1.1 command:

GE Multilin F35 Multiple Feeder Protection System 1-11

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

Pinging 1.1.1.1 with 32 bytes of data:

Destination host unreachable. Destination host unreachable. Destination host unreachable. Destination host unreachable.

Ping statistics for 1.1.1.1:

Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

Approximate round trip time in milliseconds:

Minimum = 0ms, Maximum = 0ms, Average = 0 ms

Pinging 1.1.1.1 with 32 bytes of data:

verify the IP address is programmed in the local computer by entering the ipconfig command in the command window.

C:\WINNT>ipconfig

Windows IP Configuration

Ethernet adapter <F4FE223E-5EB6-4BFB-9E34-1BD7BE7F59FF>:

Connection-specific DNS suffix. . :

IP Address. . . . . . . . . . . . : 0.0.0.0

Subnet Mask . . . . . . . . . . . : 0.0.0.0

Default Gateway . . . . . . . . . :

Ethernet adapter Local Area Connection:

Connection-specific DNS suffix . :

IP Address. . . . . . . . . . . . : 1.1.1.2

Subnet Mask . . . . . . . . . . . : 255.0.0.0

Default Gateway . . . . . . . . . :

C:\WINNT>

Before using the Quick Connect feature through the Ethernet port, disable any configured proxy settings in Internet Explorer.

1. Start the Internet Explorer software.

2. Select the Tools > Internet Options menu item and click the Connections tab.

3. Click on the LAN Settings button to open the following window.

4. Ensure that the “Use a proxy server for your LAN” box is not checked.

If this computer is used to connect to the Internet, re-enable any proxy server settings after the computer has been disconnected from the F35 relay.

1. Start the Internet Explorer software.

2. Select the “UR” device from the EnerVista Launchpad to start EnerVista UR Setup.

1-12 F35 Multiple Feeder Protection System GE Multilin

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

3. Click the Quick Connect button to open the Quick Connect dialog box.

4. Select the Ethernet interface and enter the IP address assigned to the F35, then click the Connect button. The EnerV-

ista UR Setup software creates a site named “Quick Connect” with a corresponding device also named “Quick Connect” and displays them at the upper-left of the screen.

5. Expand the sections to view data directly from the F35 device. Each time the EnerVista UR Setup software is initialized, click the Quick Connect button to establish direct communica-

tions to the F35. This ensures that configuration of the EnerVista UR Setup software matches the F35 model number. When direct communications with the F35 via Ethernet is complete, make the following changes:

1. From the Windows desktop, right-click the My Network Places icon and select Properties to open the network con-

nections window.

2. Right-click the Local Area Connection icon and select the Properties item.

3. Select the Internet Protocol (TCP/IP) item from the list provided and click the Properties button.

4. Set the computer to “Obtain a relay address automatically” as shown.

If this computer is used to connect to the Internet, re-enable any proxy server settings after the computer has been disconnected from the F35 relay.

AUTOMATIC DISCOVERY OF ETHERNET DEVICES

The EnerVista UR Setup software can automatically discover and communicate to all UR-series IEDs located on an Ethernet network.

Using the Quick Connect feature, a single click of the mouse triggers the software to automatically detect any UR-series relays located on the network. The EnerVista UR Setup software then proceeds to configure all settings and order code options in the Device Setup menu. This feature allows the user to identify and interrogate all UR-series devices at a location.

GE Multilin F35 Multiple Feeder Protection System 1-13

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

842743A3.CDR

Communications status indicators:

Green = OK Red = No communications UR icon = report is open

Quick action hot links

Expand the site list by double-clicking or selecting the +/– box.

NOTE

1.3.5 CONNECTING TO THE F35 RELAY

When unable to connect because of an "ACCESS VIOLATION," access Device Setup and refresh the order code for the device.

1. Open the Display Properties window through the Site List tree as shown. The Display Properties window opens with a status indicator on the lower left of the EnerVista UR Setup window.

2. If the status indicator is red, verify that the Ethernet network cable is properly connected to the Ethernet port on the back of the relay and that the relay has been properly setup for communications (steps A and B earlier).

If a relay icon appears in place of the status indicator, than a report (such as an oscillography or event record) is open. Close the report to re-display the green status indicator.

3. The Display Properties settings can now be edited, printed, or changed.

See chapter 4 in this manual or the EnerVista UR Setup Help File for information about the using the EnerVista UR Setup software interface.

QUICK ACTION HOT LINKS

The EnerVista UR Setup software has several quick action buttons to provide instant access to several functions that are often performed when using F35 relays. From the online window, users can select the relay to interrogate from a pull-down window, then click the button for the action they want to perform. The following quick action functions are available:

• View the F35 event record

• View the last recorded oscillography record

• View the status of all F35 inputs and outputs

• View all of the F35 metering values

• View the F35 protection summary

• Generate a service report

1-14 F35 Multiple Feeder Protection System GE Multilin

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

1.3.6 SETTING UP CYBERSENTRY AND CHANGING DEFAULT PASSWORD

If and when first using CyberSentry security, use the following procedure for set up.

1. Log in to the relay as Administrator by using the Value keys on the front panel or through EnerVista connected serially

(so that no IP address is required). If logging in through EnerVista choose Device authentication. Enter the default password "ChangeMe1#". Note that the "Lock relay" setting needs to be disabled in the Security > Supervisory menu. When this setting is disabled, configuration and firmware upgrade are possible. By default, this setting is disabled.

2. Enable the Supervisor role if you have a need for it.

3. Make any required changes in configuration, such as setting a valid IP address for communication over Ethernet.

4. Log out of the Administrator account by choosing None. Next, device or server authentication can be chosen on the login screen, but the choice is available only in EnerVista. Use

device authentication to log in using the five pre-configured roles (Administrator, Supervisor, Engineer, Operator, Observer, or Administrator and Supervisor when device authentication is disabled). When using a serial connection, only device authentication is supported. When server authentication is required, characteristics for communication with a RADIUS server must be configured on the UR. This is possible only through the EnerVista software. The RADIUS server itself also must be configured. The appendix called RADIUS Server gives an example of how to setup a simple RADIUS server. Once both the RADIUS server and the parameters for connecting UR to the server have been configured, you can choose server authentication on the login screen of EnerVista.

Figure 1–9: LOGIN SCREEN FOR CYBERSENTRY

During the commissioning phase, you have the option to bypass the use of passwords. Do so by enabling the

ACCESS

commissioning the device. You can change the password for any role either from the front panel or through EnerVista. If using EnerVista, navigate to Settings > Product Setup > Security. Change the Local Administrator Password, for

example. It is strongly recommended that the password for the Administrator be changed from the default. Changing the passwords for the other three roles is optional.

GE Multilin F35 Multiple Feeder Protection System 1-15

setting under SETTINGS > PRODUCT SETUP > SECURITY > SUPERVISORY. Be sure to disable this bypass setting after

BYPASS

1.4 UR HARDWARE 1 GETTING STARTED

EnerVista

Ethernet 10/100 Mbps

Regional

control

center

Modem

Remote

communications link Local control

Engineer

GE Multilin F485 communications converter

UR-series IED

Troubleshooting Commissioning Setting changes

Reports

RS485 115 kbps

RS232

EnerVista

842759A2.CDR

1.4UR HARDWARE 1.4.1 MOUNTING AND WIRING

See Chapter 3: Hardware for mounting and wiring instructions.

1.4.2 COMMUNICATIONS

The EnerVista UR Setup software communicates to the relay via the faceplate RS232 port or the rear panel RS485 / Ethernet ports. To communicate via the faceplate RS232 port, a standard straight-through serial cable is used. The DB-9 male end is connected to the relay and the DB-9 or DB-25 female end is connected to the computer COM2 port as described in the CPU Communication Ports section of chapter 3.

Figure 1–10: RELAY COMMUNICATION OPTIONS

To communicate through the F35 rear RS485 port from a computer RS232 port, the GE Multilin RS232/RS485 converter box is required. This device (catalog number F485) connects to the computer using a straight-through serial cable. A shielded twisted-pair (20, 22, or 24 AWG) connects the F485 converter to the F35 rear communications port. The converter terminals (+, –, GND) are connected to the F35 communication module (+, –, COM) terminals. See the CPU Communica- tion Ports section in chapter 3 for details. The line is terminated with an R-C network (that is, 120 Ω, 1 nF) as described in the chapter 3.

All messages are displayed on a backlit liquid crystal display (LCD) to make them visible under poor lighting conditions. While the keypad and display are not actively being used, the display defaults to user-defined messages. Any high-priority event-driven message automatically overrides the default message and appears on the display.

Settings files conversion from previous firmware versions is supported.

1-16 F35 Multiple Feeder Protection System GE Multilin

1.4.3 FACEPLATE DISPLAY

1 GETTING STARTED 1.5 USING THE RELAY

1.5USING THE RELAY 1.5.1 FACEPLATE KEYPAD

Display messages are organized into pages under the following headings: actual values, settings, commands, and targets. The MENU key navigates through these pages. Each heading page is divided further into logical subgroups.

The MESSAGE keys navigate through the subgroups. The VALUE keys increment or decrement numerical setting values when in programming mode. These keys also scroll through alphanumeric values in the text edit mode. Alternatively, values can be entered with the numeric keypad.

The decimal key initiates and advances to the next character in text edit mode or enters a decimal point. The HELP key can be pressed at any time for context-sensitive help messages. The ENTER key stores altered setting values. When entering an IP address on the front panel, key in the first sequence of the number, then press the • key for the deci-

mal place. For example, for 127.0.0.1, press 127, then •, then 0, then •, then 0, then •, then 1. To save the address, press the ENTER key.

1.5.2 MENU NAVIGATION

Press the MENU key to select a header display page (top-level menu). The header title appears momentarily followed by a header display page menu item. Each press of the MENU key advances through the following main heading pages:

• Actual values

• Settings

• Commands

• Targets

• User displays (when enabled)

1.5.3 MENU HIERARCHY

The setting and actual value messages are arranged hierarchically. The header display pages are indicated by double scroll bar characters (), while sub-header pages are indicated by single scroll bar characters (). The header display pages represent the highest level of the hierarchy and the sub-header display pages fall below this level. The MESSAGE UP and DOWN keys move within a group of headers, sub-headers, setting values, or actual values. Continually pressing the MESSAGE RIGHT key from a header display displays specific information for the header category. Conversely, continually pressing the MESSAGE LEFT key from a setting value or actual value display returns to the header display.

HIGHEST LEVEL LOWEST LEVEL (SETTING

 SETTINGS  PRODUCT SETUP

 SETTINGS  SYSTEM SETUP

 SECURITY 

VALUE )

ACCESS LEVEL: Restricted

GE Multilin F35 Multiple Feeder Protection System 1-17

1.5 USING THE RELAY 1 GETTING STARTED

NOTE

1.5.4 RELAY ACTIVATION

The relay is in the default “Not Programmed” state when it leaves the factory. When powered up successfully, the Trouble LED is on and the In Service LED off. The relay in the “Not Programmed” state blocks signaling of any output relay. These conditions remain until the relay is explicitly put in the “Programmed” state.

Select the menu message

RELAY SETTINGS: Not Programmed

1. To put the relay in the “Programmed” state, press either of the VALUE keys once and then press ENTER. The faceplate Trouble LED turns off and the In Service LED turns on.

The settings for the relay can be programmed manually (see Chapter 5) via the faceplate keypad or remotely via the EnerVista UR Setup software (see the EnerVista UR Setup help file).

a) PASSWORD SECURITY

It is recommended that passwords be set for each security level and assigned to specific personnel. There are two user security access levels, COMMAND and SETTING.

1. COMMAND

The COMMAND access level restricts the user from making any settings changes, but allows the user to perform the following operations:

• Change state of virtual inputs

• Clear event records

• Clear oscillography records

• Operate user-programmable pushbuttons

2. SETTING

The SETTING access level allows the user to make any changes to any of the setting values.

See the Changing Settings section in Chapter 4 for complete instructions on setting security-level passwords.

SETTINGS  PRODUCT SETUP  INSTALLATION  RELAY SETTINGS

1.5.5 RELAY PASSWORDS

b) CYBERSENTRY

When the CyberSentry option is purchased, advanced security services are available, using either device authentication or server authentication using RADIUS. When this option is purchased, the basic password security is disabled automatically. For more information, see the CyberSentry content in the Security section of the next chapter.

1.5.6 FLEXLOGIC CUSTOMIZATION

FlexLogic equation editing is required for setting user-defined logic for customizing the relay operations. See the FlexLogic section in Chapter 5.

1-18 F35 Multiple Feeder Protection System GE Multilin

1 GETTING STARTED 1.5 USING THE RELAY

1.5.7 COMMISSIONING

The F35 requires minimal maintenance after it is commissioned into service. Since the F35 is a microprocessor-based relay, its characteristics do not change over time. As such, no further functional tests are required. Expected service life is 20 years for UR devices manufactured June 2014 or later when applied in a controlled indoors environment and electrical conditions within specification.

The F35 performs a number of continual self-tests and takes the necessary action in case of any major errors (see the Relay Self-tests section in chapter 7). However, it is recommended that F35 maintenance be scheduled with other system maintenance. This maintenance can involve in-service, out-of-service, or unscheduled maintenance.

In-service maintenance:

1. Visual verification of the analog values integrity, such as voltage and current (in comparison to other devices on the

corresponding system).

2. Visual verification of active alarms, relay display messages, and LED indications.

3. LED test.

4. Visual inspection for any damage, corrosion, dust, or loose wires.

5. Event recorder file download with further events analysis. Out-of-service maintenance:

1. Check wiring connections for firmness.

2. Analog values (currents, voltages, RTDs, analog inputs) injection test and metering accuracy verification. Calibrated

test equipment is required.

3. Protection elements setting verification (analog values injection or visual verification of setting file entries against relay

settings schedule).

4. Contact inputs and outputs verification. This test can be conducted by direct change of state forcing or as part of the

system functional testing.

5. Visual inspection for any damage, corrosion, or dust.

6. Event recorder file download with further events analysis.

7. LED Test and pushbutton continuity check. Unscheduled maintenance, such as a disturbance causing system interruption:

1. View the event recorder and oscillography or fault report for correct operation of inputs, outputs, and elements. If it is concluded that the relay or one of its modules is of concern, contact GE Multilin for service.

GE Multilin F35 Multiple Feeder Protection System 1-19

1.5 USING THE RELAY 1 GETTING STARTED

1-20 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

2 PRODUCT DESCRIPTION 2.1INTRODUCTION 2.1.1 OVERVIEW

The F35 Multiple Feeder Protection System is a microprocessor based relay designed for the protection of up to five feeders with busbar voltage measurement or up to six feeders without busbar voltage.

Overcurrent and undervoltage protection, breaker recloser, underfrequency, fault diagnostics, and RTU functions are provided. The F35 provides phase, neutral/ground, instantaneous and time overcurrent protection. The time overcurrent function provides multiple curve shapes or FlexCurve™ for optimum co-ordination.

Voltage, current, and power metering is built into the relay as a standard feature. Current parameters are available as total waveform RMS magnitude, or as fundamental frequency only RMS magnitude and angle (phasor). Voltage harmonics and THD metering are also included with the relay.

Diagnostic features include a sequence of records capable of storing 1024 time-tagged events. The internal clock used for time-tagging can be synchronized with an IRIG-B signal, using the Simple Network Time Protocol (SNTP) over the Ethernet port, or using the Precision Time Protocol (PTP). This precise time stamping allows the sequence of events to be determined throughout the system. Events can also be programmed (via FlexLogic™ equations) to trigger oscillography data capture which may be set to record the measured parameters before and after the event for viewing on a personal computer (PC). These tools significantly reduce troubleshooting time and simplify report generation in the event of a system fault.

Several options are available for communication. A faceplate RS232 port can be used to connect to a computer for the programming of settings and the monitoring of actual values. The RS232 port has a fixed baud rate of 19.2 kbps. The rear RS485 port allows independent access by operating and engineering staff. It can be connected to system computers with baud rates up to 115.2 kbps. All serial ports use the Modbus RTU protocol. The IEC 60870-5-103 protocol is supported on the RS485 interface. IEC 60870-5-103, DNP, and Modbus cannot be enabled simultaneously on this interface. Also only one of the DNP, IEC 60870-5-103, and IEC 60870-5-104 protocols can be enabled at any time on the relay. When the IEC 60870-5-103 protocol is chosen, the RS485 port has a fixed even parity and the baud rate can be either 9.6 kbps or 19.2 kbps. The 100Base-FX or 100Base-T Ethernet interface provides fast, reliable communications in noisy environments. The Ethernet port supports IEC 61850, Modbus/TCP, and TFTP protocols, PTP (according to IEEE Std. 1588-2008 or IEC

61588), and allows access to the relay via any standard web browser (F35 web pages). The IEC 60870-5-104 protocol is supported on the Ethernet port. The Ethernet port also supports the Parallel Redundancy Protocol (PRP) of IEC 62439-3 (clause 4, 2012) when purchased as an option.

Settings and actual values can be accessed from the front panel or EnerVista software. The F35 IEDs use flash memory technology which allows field upgrading as new features are added. The following Single

line diagram illustrates the relay functionality using ANSI (American National Standards Institute) device numbers.

Table 2–1: ANSI DEVICE NUMBERS AND FUNCTIONS

DEVICE NUMBER

27P Phase undervoltage 51G Ground time overcurrent 27X Auxiliary undervoltage 51N Neutral time overcurrent 32N Wattmetric zero-sequence directional 51P Phase time overcurrent 49 Thermal overload protection 51_ Negative-sequence time overcurrent 50DD Disturbance detector 52 AC circuit breaker 50G Ground instantaneous overcurrent 59N Neutral overvoltage 50N Neutral instantaneous overcurrent 59X Auxiliary overvoltage 50P Phase instantaneous overcurrent 79 Autoreclose 50_2 Negative-sequence instantaneous overcurrent 81U Underfrequency

FUNCTION DEVICE

NUMBER

FUNCTION

GE Multilin F35 Multiple Feeder Protection System 2-1

2.1 INTRODUCTION 2 PRODUCT DESCRIPTION

832738A9.CDR

50G 51G

Same functions as breaker 1

For breaker 1

51P 51_2 50N 51N

81U

59N 59X

27P27X

Metering

2 345

F35 Multiple Feeder Protection System

Monitoring

TRIP

Transducer

inputs

FlexElements

50P 50_2

32N

Table 2–2: OTHER DEVICE FUNCTIONS

FUNCTION FUNCTION FUNCTION

Breaker arcing current (I

Breaker control Ethernet Global Data protocol (optional) Setting groups (6) Breaker restrike Event recorder Teleprotection inputs and outputs Contact inputs (up to 96) Fault detector and fault report Time synchronization over IRIG-B or IEEE

Contact outputs (up to 64) FlexElements™ (16) Time synchronization over SNTP Control pushbuttons FlexLogic equations Transducer inputs and outputs CyberSentry™ security IEC 60870-5-103 communications

Data logger IEC 61850 communications (optional) User-programmable LEDs Demand Incipient cable fault detection User-programmable pushbuttons Digital counters (8) Metering: current, voltage, power, energy,

Digital elements (48) Modbus user map Virtual inputs (64) Direct inputs and outputs (32) Non-volatile latches Virtual outputs (96) Disconnect switches Non-volatile selector switch

t) DNP 3.0 or IEC 60870-5-104

Figure 2–1: SINGLE LINE DIAGRAM

communications

(optional)

frequency, harmonics, THD

Oscillography

1588

User-definable displays

User-programmable self-tests

2.1.2 SECURITY

The following security features are available:

• Password security — Basic security present in the default offering of the product

• EnerVista security — Role-based access to various EnerVista software screens and configuration elements. The feature is available in the default offering of the product and only in the EnerVista software.

• CyberSentry security — Advanced security options available as a software option. When purchased, the options are automatically enabled, and the default Password security and EnerVista security are disabled.

Changing the password, or any other setting, does not take the relay out of service. The relay is taken out of service when a settings file is written to it.

2-2 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

a) ENERVISTA SECURITY

The EnerVista security management system is a role-based access control (RBAC) system that allows an administrator to manage the privileges of multiple users. This allows for access control of UR devices by multiple personnel within a substation and conforms to the principles of RBAC as defined in ANSI INCITS 359-2004. The EnerVista security management system is disabled by default to allow the administrator direct access to the EnerVista software after installation. It is recommended that security be enabled before placing the device in service.

Basic password or enhanced CyberSentry security applies, depending on purchase.

b) PASSWORD SECURITY

Password security is a basic security feature present in the default offering of the product. Two levels of password security are provided: command and setting. The following operations are under command password supervision:

• Changing the state of virtual inputs

• Clearing the event records

• Clearing the oscillography records

• Changing the date and time

• Clearing energy records

• Clearing the data logger

• Clearing the user-programmable pushbutton states The following operations are under setting password supervision:

• Changing any setting

• Test mode operation The F35 supports password entry from a local or remote connection. Local access is defined as any access to settings or

commands via the faceplate interface. This includes both keypad entry and the through the faceplate RS232 port. Remote access is defined as any access to settings or commands via any rear communications port. This includes both Ethernet and RS485 connections. Any changes to the local or remote passwords enables this functionality.

When entering a settings or command password via EnerVista or any serial interface, the user must enter the corresponding connection password. If the connection is to the back of the F35, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password applies.

Password access events are logged in the Event Recorder.

c) CYBERSENTRY SECURITY

CyberSentry Embedded Security is a software option that provides advanced security services. When this option is purchased, the basic password security is disabled automatically.

CyberSentry provides security through the following features:

• An Authentication, Authorization, Accounting (AAA) Remote Authentication Dial-In User Service (RADIUS) client that

is centrally managed, enables user attribution, provides accounting of all user activities, and uses secure standardsbased strong cryptography for authentication and credential protection.

• A Role-Based Access Control (RBAC) system that provides a permission model that allows access to UR device oper-

ations and configurations based on specific roles and individual user accounts configured on the AAA server (that is, Administrator, Supervisor, Engineer, Operator, Observer).

• Security event reporting through the Syslog protocol for supporting Security Information Event Management (SIEM)

systems for centralized cybersecurity monitoring.

• Strong encryption of all access and configuration network messages between the EnerVista software and UR devices

using the Secure Shell (SSH) protocol, the Advanced Encryption Standard (AES), and 128-bit keys in Galois Counter Mode (GCM) as specified in the U.S. National Security Agency Suite B extension for SSH and approved by the National Institute of Standards and Technology (NIST) FIPS-140-2 standards for cryptographic systems.

GE Multilin F35 Multiple Feeder Protection System 2-3

2.1 INTRODUCTION 2 PRODUCT DESCRIPTION

842838A2.CDR

Administrator

Engineer

Supervisor

Operator

Observer

CYBERSENTRY USER ROLES

CyberSentry user roles (Administrator, Engineer, Operator, Supervisor, Observer) limit the levels of access to various UR device functions. This means that the EnerVista software allows for access to functionality based on the user’s logged in role.

Example: Administrative functions can be segmented away from common operator functions, or engineering type access, all of which are defined by separate roles, as shown in the following figure, so that access of UR devices by multiple personnel within a substation is allowed.

Figure 2–2: CYBERSENTRY USER ROLES

The table lists the roles that are supported and their corresponding capabilities.

Table 2–3: PERMISSIONS BY USER ROLE FOR CYBERSENTRY

Device Definition RRRRR

Settings |------------ Product Setup

Roles Administrator Engineer Operator Supervisor Observer

Complete access Complete access

|--------------- Security (CyberSentry) RW R R R R |--------------- Supervisory see table notes R R see table notes R |--------------- Display Properties RW RW R R R

|--------------|--------------- Communications RW RW R R R |--------------- Modbus user map RW RW R R R |--------------- Real Time Clock RW RW R R R |--------------- Oscillography RW RW R R R |--------------- Data Logger RW RW R R R |--------------- Demand RW RW R R R

|---------------

|--------------|--------------- Control Pushbuttons RW RW R R R

|--------------|--------------- Flex states RW RW R R R

|--------------|--------------- Direct I/O RW RW R R R

Clear relay records (settings) RW RW R R R

User Programmable LEDs RW RW R R R

User Programmable self test RW RW R R R

User programmable Pushbuttons RW RW R R R

User definable displays RW RW R R R

except for CyberSentry Security

Command menu

Authorizes writing

Default role

2-4 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

Roles Administrator Engineer Operator Supervisor Observer

|--------------- Tele-protection RW RW R R R

|--------------- Contact Input RW RW R R R

|---------------

|--------------- Virtual Inputs RW RW R R R

|--------------- Contact Output RW RW R R R

|--------------- Virtual Output RW RW R R R

|--------------- Remote Devices RW RW R R R

|--------------- Remote Inputs RW RW R R R

|--------------- Remote DPS input RW RW R R R

|---------------

|--------------- Resetting RW RW R R R

|--------------- Direct Inputs RW RW R R R

|--------------- Direct Outputs RW RW R R R

|--------------- Teleprotection RW RW R R R

|--------------- Direct Analogs RW RW R R R

|--------------- Direct Integers RW RW R R R

|---------------

|--------------|------------ Transducer I/O RW RW R R R |------------ Testing RW RW R R R |------------ Front Panel Labels Designer NA NA NA NA NA

|------------ Protection Summary NA NA NA NA NA Commands RW RW RW R R |------------ Virtual Inputs RW RW RW R R |------------ Clear Records RW RW RW R R

|------------ Set date and time RW RW RW R R

User Displays RRRRR

Targets RRRRR Actual Values RRRRR

|------------ Product Info R R R R R Maintenance RW RW R R R |------------ Modbus Analyzer NA NA NA NA NA

Contact Input threshold RW RW R R R

Remote Output DNA Bit Pair RW RW R R R

Remote Output user Bit Pair RW RW R R R

IEC61850 GOOSE Analogs RW RW R R R

IEC61850 GOOSE Integers RW RW R R R

GE Multilin F35 Multiple Feeder Protection System 2-5

2.1 INTRODUCTION 2 PRODUCT DESCRIPTION

Roles Administrator Engineer Operator Supervisor Observer

|------------ Change Front Panel RW RW RW R R |------------ Update Firmware Yes No No No No

|------------ Retrieve File Yes No No No No

Table Notes:

1. RW = read and write access

2. R = read access

3. Supervisor = RW (default), Administrator = R (default), Administrator = RW (only if Supervisor role is disabled)

4. NA = the permission is not enforced by CyberSentry Security

CYBERSENTRY USER AUTHENTICATION

There are two types of authentication supported by CyberSentry that can be used to access the UR device:

• Device Authentication (local UR device authenticates)

• Server Authentication (RADIUS server authenticates) The EnerVista software allows access to functionality that is determined by the user role, which comes either from the local

UR device or RADIUS server. The EnerVista software has a device authentication option on the login screen for accessing the UR device. When the

"Device" button is selected, the UR uses its local authentication database and not the RADIUS server to authenticate the user. In this case, it uses its built-in roles (Administrator, Engineer, Supervisor, Observer, Operator, or Administrator and Supervisor when Device Authentication is disabled) as login names and the associated passwords are stored on the UR device. As such, when using the local accounts, access is not user-attributable.

In cases where user attributable access is required especially to facilitate auditable processes for compliance reasons, use RADIUS authentication only.

When the "Server" Authentication Type option is selected, the UR uses the RADIUS server and not its local authentication database to authenticate the user.

No password or security information are displayed in plain text by the EnerVista software or UR device, nor are they ever transmitted without cryptographic protection.

CyberSentry Server Authentication

The UR has been designed to automatically direct authentication requests based on user names. In this respect, local account names on the UR are considered as reserved, and not used on a RADIUS server.

The UR automatically detects whether an authentication request is to be handled remotely or locally. As there are only five local accounts possible on the UR, if the user ID credential does not match one of the five local accounts, the UR automatically forwards the request to a RADIUS server when one is provided.

If a RADIUS server is provided, but is unreachable over the network, server authentication requests are denied. In this situation, use local UR accounts to gain access to the UR system.

2.1.3 IEC 870-5-103 PROTOCOL

IEC 870-5-103 is a companion standard to IEC 870-5 suit of standards for transmission protocols. It defines messages and procedures for interoperability between protection equipment and devices of a control system in a substation for communicating on a serial line.

The IEC 60870-5-103 is an unbalanced (master-slave) protocol for coded-bit serial communication, exchanging information with a control system. In the context of this protocol, the protection equipment is the slave and the control system is the master. The communication is based on a point to point principle. The master must be able to interpret the IEC 60870-5103 communication messages.

The UR implementation of IEC 60870-5-103 consists of the following functions:

• Report binary inputs

• Report analog values (measurands)

2-6 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

• Commands

• Time synchronization The RS485 port supports IEC 60870-5-103.

GE Multilin F35 Multiple Feeder Protection System 2-7

2.2 ORDER CODES 2 PRODUCT DESCRIPTION

NOTE

2.2ORDER CODES 2.2.1 OVERVIEW

The F35 is available as a 19-inch rack horizontal mount or reduced-size (¾) vertical unit and consists of the following modules: power supply, CPU, CT/VT, contact input and output, transducer input and output, and inter-relay communications. Each of these modules can be supplied in a number of configurations specified at the time of ordering. The information required to completely specify the relay is provided in the following tables (see chapter 3 for full details of relay modules).

Order codes are subject to change without notice. See the ordering page at

http://www.gegridsolutions.com/multilin/order.htm

for the latest options.

The order code structure is dependent on the mounting option (horizontal or vertical) and the type of CT/VT modules (enhanced diagnostic CT/VT modules or HardFiber

process bus modules). The order code options are described in the

following sub-sections.

2.2.2 ORDER CODES WITH ENHANCED CT/VT MODULES

The order codes for the horizontal mount units are shown below.

Table 2–4: F35 ORDER CODES (HORIZONTAL UNITS)

F35 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount

U | | | | | | | | | | RS485 and Two Multi-mode fiber 100Base-FX (SFP with LC), One 10/100Base-T (SFP with RJ45) V | | | | | | | | | | RS485 and Three 10/100Base- T (SFP with RJ45)

AW | | | | | | | | | CyberSentry Lvl 1 and IEC 61850 and PID controller

B4 | | | | | | | | | IEEE 1588 and IEC 61850 and Ethernet Global Data (EGD) BW | | | | | | | | | IEEE 1588 and IE C 61850 and PID controller D0 | | | | | | | | | IEEE 1588 and CyberSent ry Lvl 1 C0 | | | | | | | | | Parallel Redundancy Protocol ( PRP) C1 | | | | | | | | | PRP and Ethernet Global Data C3 | | | | | | | | | PRP and IEC 61850 C4 | | | | | | | | | PRP, Ethernet Global Data, and IEC 61850 CW | | | | | | | | | PRP, PID controller, and IEC 61850 D1 | | | | | | | | | IEEE 1588 and CyberSent ry Lvl 1 and Ethernet Global Data (EGD) D3 | | | | | | | | | IEEE 1588 and CyberSent ry Lvl 1 and IEC 61850 D4 | | | | | | | | | IEEE 1588 and CyberSent ry Lvl 1 and IEC 61850 and Ethernet Global Data (EGD) DW | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 and PID controller

E0 | | | | | | | | | IEEE 1588 and PRP

E1 | | | | | | | | | IEEE 1588, PRP, and Ethernet Global Data

E3 | | | | | | | | | IEEE 1588, PRP, and IEC 61850

F0 | | | | | | | | | PRP and CyberSentry Lvl 1

F1 | | | | | | | | | PRP, CyberSentry Lvl 1, and Ethernet Global Data

F3 | | | | | | | | | PRP, CyberSentry Lvl 1, and IEC 61850

F4 | | | | | | | | | PRP, CyberSentry Lvl 1, Ethernet Global Data, and IEC 61850 FW | | | | | | | | | P RP, CyberSentry Lvl 1, PID controller, and IEC 61850 G0 | | | | | | | | | IEEE 1588 and PRP G1 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and Ethernet Global Data G3 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and IEC 61850 G4 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Ethernet Global Data, and IEC 61850 GW | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, PID controller, and IEC 61850

J0 | | | | | | | | | IEC 60870-5-103

J1 | | | | | | | | | IEC 60870-5-103 + EGD

J3 | | | | | | | | | IEC 60870-5-103 + IEC 61850

K0 | | | | | | | | | IE EE1588 + PRP + IEC 60870-5-103

K1 | | | | | | | | | IE EE1588 + PRP + IEC 60870-5-103 + EGD

K3 | | | | | | | | | IE EE1588 + PRP + IEC 60870-5-103 + IEC 61850

L0 | | | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1

L1 | | | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + EGD

L3 | | | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + IEC 61850

L4 | | | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + EGD + IE C 61850 LW | | | | | | | | | IEC 60870-5- 103 + IEEE1588 + PRP + CyberSentry Lvl 1 + PID controller + IEC 61850

A | | | | | | | | Horizontal (19” rack) w ith harsh environmental coating

L | | | | | | | Enhanced front panel with English display and user-programmable pushbuttons

N | | | | | | | Enhanced front panel with French display and user-programmable pushbuttons

T | | | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons V | | | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons W | | | | | | | Enhanced front panel with Turkish display Y | | | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons

I | | | | | | | Enhanced front panel with German display

J | | | | | | | Enhanced front panel with German display and user-progr ammable pushbuttons

2-8 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.2 ORDER CODES

Table 2–4: F35 ORDER CODES (HORIZONTAL UNITS)

POWER SUPPLY (redundant supply must be same type as main supply)

ENHANCED DIAGNOSTICS CT/VT DSP (requires all DSP to be enhanced diagnostic)

DIGITAL INPUTS/OUTPUTS XX XX XX XX XX No Module

TRANSDUCER INPUTS/OUTPUTS (select a maximum of 3 per unit)

INTER-RELAY COMMUNICATIONS (select a maximum of 1 per unit)

F35 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount

| | XX | XX | No DSP module (slots M and U only)

8L | 8L | 8L | Standard 4CT/4VT with enhanced diagnostics 8M | 8M | 8M | Sensitive Ground 4CT/4VT with enhanced diagnostics 8N | 8N | 8N | Standard 8CT with enhanced diagnostics 8R | 8R | 8R | Sensitive Ground 8CT with enhanced diagnostics 8V | | | | | Standard 8VT with enhanced diagnostics (only one module supported)

4A 4A 4A 4A 4A 4 Solid-State (no monitoring) MOSFET outputs 4B 4B 4B 4B 4B 4 Solid-State (voltage with optional current) MOSFET outputs 4C 4C 4C 4C 4C 4 Solid-State (current with optional voltage) MOSFET outputs 4D 4D 4D 4D 4D 16 digital inputs with Auto-Burnishing (maximum of three modules within a case) 4L 4L 4L 4L 4L 14 Form-A (no monitoring) Latching outputs 67 67 67 67 67 8 Form-A (no monitoring) outputs 6A 6A 6A 6A 6A 2 Form-A (voltage with optional current) and 2 F orm-C outputs, 8 digital inputs 6B 6B 6B 6B 6B 2 Form-A (voltage with optional current) and 4 F orm-C outputs, 4 digital inputs 6C 6C 6C 6C 6C 8 Form-C outputs 6D 6D 6D 6D 6D 16 digital inputs 6E 6E 6E 6E 6E 4 Form-C outputs, 8 digital inputs 6F 6F 6F 6F 6F 8 Fast Form-C outputs 6G 6G 6G 6G 6G 4 Form-A (voltage with optional current) outputs, 8 digi tal inputs 6H 6H 6H 6H 6H 6 Form-A (voltage with optional current) outputs, 4 digital inputs 6K 6K 6K 6K 6K 4 Form-C and 4 Fast Form-C outputs 6L 6L 6L 6L 6L 2 Form-A (current with optional voltage) and 2 F orm-C outputs, 8 digital inputs 6M 6M 6M 6M 6M 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs 6N 6N 6N 6N 6N 4 Form-A (current with optional voltage) outputs, 8 digital inputs 6P 6P 6P 6P 6P 6 Form-A (current with optional voltage) outputs, 4 digital inputs 6R 6R 6R 6R 6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs 6S 6S 6S 6S 6S 2 Form-A (no monitoring) and 4 Form-C out puts, 4 digital inputs 6T 6T 6T 6T 6T 4 Form-A (no monitoring) outputs, 8 digital inputs 6U 6U 6U 6U 6U 6 Form-A (no monitoring) outputs, 4 digital inputs 6V 6V 6V 6V 6V 2 Form-A outputs, 1 Form-C output, 2 Form-A (no moni toring) latching outputs, 8 digital inputs 5A 5A 5A 5A 5A 4 DCmA inputs, 4 DCmA outputs (only one 5A module is allowed) 5C 5C 5C 5C 5C 8 RTD inputs 5D 5D 5D 5D 5D 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed) 5E 5E 5E 5E 5E 4 RTD inputs, 4 DCmA inputs 5F 5F 5F 5F 5F 8 DCmA inputs

2A C37.94SM, 1300 nm single-mode, ELED, 1 channel single-mode 2B C37.94SM, 1300 nm single-mode, ELED, 2 channel single-mode 2E Bi-phase, single channel 2F Bi-phase, dual channel 2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel 2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels

2I Channel 1 - IEEE C37.94, MM, 64/128 kbps; Channel 2 - 1300 nm, single-mode, Laser 2J C hannel 1 - IEEE C37.94, MM, 64/128 kbps; Channel 2 - 1550 nm, single-mode, Laser 72 1550 nm, single-mode, Laser, 1 Channel 73 1550 nm, single-mode, Laser, 2 Channel 74 Channel 1 - RS42 2; Channel 2 - 1550 nm, single-mode, Laser 75 Channel 1 - G.703; Channel 2 - 1550 nm, single-mode Laser 76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel 77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels 7A 820 nm, multimode, LED, 1 Channel 7B 1300 nm, multimode, LED, 1 Channel 7C 1300 nm, single-mode, ELED, 1 Channel 7D 1300 nm, single-mode, Laser, 1 Channel 7E Channel 1 - G.703; Channel 2 - 820 nm, multimode 7F Channel 1 - G.703; Channel 2 - 1300 nm, multimode 7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED 7H 820 nm, multimode, LED, 2 Channels

7I 1300 nm, multimode, LED, 2 C hannels 7J 1300 nm, single-mode, ELED, 2 Channels 7K 1300 nm, single-mode, Laser, 2 Channels 7L Channel 1 - RS42 2; Channel 2 - 820 nm, multimode, LED 7M Channel 1 - RS422; Channel 2 - 1300 nm, multimode, LED 7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED 7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, Laser 7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser 7R G.703, 1 Channel 7S G.703, 2 Channels 7T RS422, 1 Channel 7W RS422, 2 Channels

The order codes for the reduced size vertical mount units are shown below.

Table 2–5: F35 ORDER CODES (REDUCED SIZE VERTICAL UNITS)

F35 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)

U | | | | | | | | RS485 and Two Multi-mode fiber 100Base-FX (SFP with LC), One 10/100Base-T (SFP with RJ45) V | | | | | | | | RS485 and Three 10/100Base-T (SFP with RJ45)

AW | | | | | | | CyberSentry Lvl 1 and IEC 61850 and PID cont roller

B4 | | | | | | | IEEE 1588 and I EC 61850 and Ethernet Global Data (EGD) BW | | | | | | | IEEE 1588 and IEC 61850 and PID controller C0 | | | | | | | Parallel Redundancy Protocol (PRP) C1 | | | | | | | PRP and Ethernet Global Data C3 | | | | | | | PRP and IEC 61850 C4 | | | | | | | PRP, Ethernet Global Data, and IEC 61850 CW | | | | | | | PRP, PID controller, and IEC 61850 D0 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 D1 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 a nd Ethernet Global Data (EGD) D3 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 a nd IEC 61850 D4 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 and Ethernet Global Data (EGD) DW | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and I EC 61850 and PID controller

E0 | | | | | | | IEEE 15 88 and PRP

E1 | | | | | | | IEEE 1588, P RP, and Ethernet Global Data

E3 | | | | | | | IEEE 1588, P RP, and IEC 61850

F0 | | | | | | | PR P and CyberSentry Lvl 1

F1 | | | | | | | PR P, CyberSentry Lvl 1, and Ethernet Global Data

F3 | | | | | | | PR P, CyberSentry Lvl 1, and IEC 61850

F4 | | | | | | | PRP, CyberSentry Lvl 1, Ethernet Global Data, and IEC 61850 FW | | | | | | | PRP, CyberSentry Lvl 1, PID controller, and IEC 61850 G0 | | | | | | | IEEE 1588 and PRP G1 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and Ethernet Global Data G3 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and IEC 61850 G4 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Ethernet Global Data, and IEC 61850

GE Multilin F35 Multiple Feeder Protection System 2-9

2.2 ORDER CODES 2 PRODUCT DESCRIPTION

Table 2–5: F35 ORDER CODES (REDUCED SIZE VERTICAL UNITS)

F35 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)

GW | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, PID controller, and IEC 61850

JW | | | | | | | IEC 60870-5-103 + PID controller + IEC 61850

KW | | | | | | | IEEE1588 + PRP + IE C 60870-5-103 + PID controller + IEC 61850

L0 | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 L1 | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + EGD L3 | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + IEC 61850

POWER SUPPLY H | | | | 125 / 250 V AC/DC power supply

ENHANCED DIAGNOSTICS CT/VT DSP (requires all DSP to be enhanced diagnostic)

DIGITAL INPUTS/OUTPUTS XX XX XX No Module

TRANSDUCER INPUTS/OUTPUTS (select a maximum of 3 per unit)

INTER-RELAY COMMUNICATIONS (select a maximum of 1 per unit) For the last module, slot P is used for digital and transducer input/output modules; slot R is used for inter-relay communications modules.

L4 | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + EGD + IEC 61850

LW | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + PID controller + IEC 61850

B | | | | | | Vertical (3/4 rack) with harsh environmental coating

K | | | | | Enhanced front panel with English display M | | | | | Enhanced front panel with French display Q | | | | | Enhanced front panel with Russian display U | | | | | Enhanced front panel with Chinese display L | | | | | Enhanced front panel with English display and user-programmable pushbut tons N | | | | | Enhanced front panel with French display and user-programmable pushbuttons T | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons V | | | | | Enhanced front panel with Chinese display and user-programmable pushbut tons W | | | | | Enhanced front panel with Turkish display Y | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons

I | | | | | Enhanced front panel with German display

J | | | | | Enhanced front panel with German display and user-programmable pushbuttons

L | | | | 24 to 48 V (DC only) pow er supply

XX | XX | No DSP module (slots M and U only)

8L | 8L | Standard 4CT/4VT with enhanced diagnostics 8M | 8M | Sensitive Ground 4CT/4VT with enhanced diagnostics 8N | 8N | Standard 8CT with enhanced diagnostics 8R | 8R | Sensitive Ground 8CT with enhanced diagnostics 8V | | | Standard 8VT with enhanced diagnostics (only one module supported)

4A 4A 4A 4 Solid-State (no monitoring) MOSFET outputs 4B 4B 4B 4 Solid-State (voltage with optional current) MOSFET outputs 4C 4C 4C 4 Solid-State (current with optional voltage) MOSFET outputs 4D 4D 4D 16 digital inputs with Auto-Burnishing (maximum of three modules within a case)

4L 4L 4L 14 Form-A (no monitoring) Latching outputs

67 67 67 8 Form-A (no monitoring) outputs 6A 6A 6A 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs 6B 6B 6B 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs 6C 6C 6C 8 Form-C outputs 6D 6D 6D 16 digital inputs 6E 6E 6E 4 Form-C outputs, 8 digital inputs

6F 6F 6F 8 Fast Form-C outputs 6G 6G 6G 4 Form-A (voltage with optional current) outputs, 8 digital inputs 6H 6H 6H 6 Form-A (voltage with optional current) outputs, 4 digital inputs 6K 6K 6K 4 Form-C and 4 Fast Form-C outputs

6L 6L 6L 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs 6M 6M 6M 2 Form-A (curr ent with optional voltage) and 4 Form-C outputs, 4 digital inputs 6N 6N 6N 4 Form-A (current with optional voltage) outputs, 8 digital inputs 6P 6P 6P 6 Form-A (current with optional voltage) outputs, 4 digital inputs 6R 6R 6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs 6S 6S 6S 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs

6T 6T 6T 4 Form-A (no monitoring) outputs, 8 digital inputs 6U 6U 6U 6 Form-A (no monitoring) outputs, 4 digital inputs 6V 6V 6V 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs 5A 5A 5A 4 DCmA inputs, 4 DCmA outputs (only one 5A module is allowed) 5C 5C 5C 8 RTD inputs 5D 5D 5D 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed) 5E 5E 5E 4 RTD inputs, 4 DCmA inputs

5F 5F 5F 8 DCmA inputs

2A C37.94SM, 1300 nm single-mode, ELED, 1 channel single-mode 2B C37.94SM, 1300 nm single-mode, ELED, 2 channel single-mode 2E Bi-phase, single channel

2F Bi-phase, dual channel 2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel 2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels

2I Channel 1 - IEEE C37.94, MM, 6 4/128 kbps; Channel 2 - 1300 nm, single-mode, Laser 2J Channel 1 - IEEE C37.94, MM, 64/128 kbps; Channel 2 - 1550 nm, single-mode, Laser 72 1550 nm, single-mode, Laser, 1 Channel 73 1550 nm, single-mode, Laser, 2 Channel 74 Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, Laser 75 Channel 1 - G.703; Channel 2 - 1550 nm, single-mode Laser 76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel 77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels 7A 820 nm, multimode, LED, 1 Channel 7B 1300 nm, multimode, LED, 1 Channel 7C 1300 nm, single-mode, ELED, 1 Channel 7D 1300 nm, single-mode, Laser, 1 Channel 7E Channel 1 - G.703; Channel 2 - 820 nm, multimode 7F Channel 1 - G.703; Channel 2 - 1300 nm, multimode 7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED 7H 820 nm, multimode, LED, 2 Channels

7I 1300 nm, multimode, LED, 2 Channels 7J 1300 nm, single-mode, ELED, 2 Channels 7K 1300 nm, single-mode, Laser, 2 Channels 7L Channel 1 - RS422; Channel 2 - 820 nm, multimode, LED 7M Channel 1 - RS422; Channel 2 - 1300 nm, multimode, LED 7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED 7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, Laser 7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser 7R G.703, 1 Channel 7S G.703, 2 Channels 7T RS422, 1 Channel 7W RS422, 2 Channels

2-10 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.2 ORDER CODES

2.2.3 ORDER CODES WITH PROCESS BUS MODULES

The order codes for the horizontal mount units with the process bus module are shown below.

Table 2–6: F35 ORDER CODES (HORIZONTAL UNITS WITH PROCESS BUS)

POWER SUPPLY (redundant supply must be same type as main supply)

INTER-RELAY COMMUNICATIONS (select a maximum of 1 per unit)

F35 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount

U | | | | | | | | | | RS485 and Two Multi-mode fiber 100Base-FX (SFP w ith LC), One 10/100Base-T (SFP with RJ45) V | | | | | | | | | | RS485 and T hree 10/100Base-T (SFP with RJ45)

AW | | | | | | | | | CyberSentry Lvl 1 and IEC 61850 and PID controller

B4 | | | | | | | | | IEEE 1588 and IEC 61850 an d Ethernet Global Data (EGD) BW | | | | | | | | | IEEE 1588 and IEC 61850 an d PID controller C0 | | | | | | | | | Parallel Redundancy Protocol (PRP) C1 | | | | | | | | | PRP and Ethernet Global Data C3 | | | | | | | | | PRP and IEC 61850 C4 | | | | | | | | | PRP, Ethernet Global Data, and IEC 61850 CW | | | | | | | | | PRP, PID controller, and IEC 61850 D0 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 D1 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and Ethernet Global Data (EGD) D3 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 D4 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 and Ethernet Global Data (EGD) DW | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850 and PID controller

E0 | | | | | | | | | IEEE 1588 and P RP

E1 | | | | | | | | | IEEE 1588, PR P, and Ethernet Global Data

E3 | | | | | | | | | IEEE 1588, PR P, and IEC 61850

F0 | | | | | | | | | PRP and CyberSentry Lvl 1

F1 | | | | | | | | | PRP, CyberSentry Lvl 1, and Ethernet Global Data

F3 | | | | | | | | | PRP, CyberSentry Lvl 1, and IEC 61850

F4 | | | | | | | | | PRP, CyberSentry Lvl 1, Ethernet Global Data, and IEC 61850 FW | | | | | | | | | PRP, CyberSentry Lvl 1, PID controller, and IEC 61850 G0 | | | | | | | | | IEEE 1588 and PRP G1 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and Ethernet Global Data G3 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and IEC 61850 G4 | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Ethernet Global Data, and IEC 61850 GW | | | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, PID controller, and IEC 61850

J0 | | | | | | | | | IEC 60870-5-103

J1 | | | | | | | | | IEC 60870-5-103 + EGD

J3 | | | | | | | | | IEC 60870-5-103 + IEC 61850

K0 | | | | | | | | | IEEE1588 + PR P + IEC 60870-5-103

K1 | | | | | | | | | IEEE1588 + PR P + IEC 60870-5-103 + EGD

K3 | | | | | | | | | IEEE1588 + PR P + IEC 60870-5-103 + IEC 61850

L0 | | | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1

L1 | | | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + EGD

L3 | | | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + IEC 61850

L4 | | | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + EGD + IEC 61850 LW | | | | | | | | | IEC 60870-5-103 + IE EE1588 + PRP + CyberSentry Lvl 1 + PID controller + IEC 61850

A | | | | | | | | Horizontal (19” rack) with harsh environmental coating

K | | | | | | | Enhanced front panel with English display M | | | | | | | Enhanced front panel with French display Q | | | | | | | Enhanced front panel with Russian display U | | | | | | | Enhanced front panel with Chinese display L | | | | | | | Enhanced front panel with English display and user-programmable pushbuttons N | | | | | | | Enhanced front panel with French display and user-programmable pushbuttons T | | | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons V | | | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons

W | | | | | | | Enhanced front panel with Turkish display

Y | | | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons

I | | | | | | | Enhanced front panel with German display

J | | | | | | | Enhanced front panel with German display and user-programmable pushbuttons

4A 4A | 4 Solid-State (no monitoring) MOSFET outputs 4B 4B | 4 Solid-State (voltage with optional current) MOSFET outputs 4C 4C | 4 Soli d-State (current with optional voltage) MOSFET outputs 4D 4D | 16 digital inputs with Aut o-Burnishing (maximum of three modules within a case) 4L 4L | 14 Form-A (no monitoring) Latching outputs 67 67 | 8 Form-A (no monitoring) outputs 6A 6A | 2 Form-A (voltage with optional current) and 2 Form- C outputs, 8 digital inputs 6B 6B | 2 Form-A (voltage with optional current) and 4 Form- C outputs, 4 digital inputs 6C 6C | 8 Form-C outputs 6D 6D | 16 digital inputs 6E 6E | 4 Form-C outputs, 8 digital inputs 6F 6F | 8 Fast Form-C outputs 6G 6G | 4 Form-A (voltage with optional current) outputs, 8 digital inputs 6H 6H | 6 Form-A ( voltage with optional current) outputs, 4 digital inputs 6K 6K | 4 Form-C and 4 Fast Form-C outputs 6L 6L | 2 Form-A (current with optional voltage) and 2 Form-C ou tputs, 8 digital inputs 6M 6M | 2 Form-A ( current with optional voltage) and 4 Form-C outputs, 4 digital inputs 6N 6N | 4 Form-A ( current with optional voltage) outputs, 8 digital inputs 6P 6P | 6 Form-A (current with optional voltage) outputs, 4 digital inputs 6R 6R | 2 Form-A ( no monitoring) and 2 Form-C outputs, 8 digital inputs 6S 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs 6T 6T | 4 Form-A (no monitoring) outputs, 8 digital inputs 6U 6U | 6 Form-A ( no monitoring) outputs, 4 digital inputs 6V 6V | 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs

2I Channel 1 - IEEE C37.94, MM, 64/128 kbps; Channel 2 - 1300 nm, single-mode, Laser

2J Channel 1 - IEEE C37.94, MM, 64/128 kbps; Channel 2 - 1550 nm, single-mode, Laser

GE Multilin F35 Multiple Feeder Protection System 2-11

2.2 ORDER CODES 2 PRODUCT DESCRIPTION

Table 2–6: F35 ORDER CODES (HORIZONTAL UNITS WITH PROCESS BUS)

F35 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount

72 1550 nm, single-mode, Laser, 1 Channel 73 1550 nm, single-mode, Laser, 2 Channel 74 Channel 1 - RS422; C hannel 2 - 1550 nm, single-mode, Laser 75 Channel 1 - G.703; Channel 2 - 1550 nm, single-mode Laser 76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel 77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels 7A 820 nm, multimode, LED, 1 Channel 7B 1300 nm, multimode, LED, 1 Channel 7C 1300 nm, single-mode, ELED, 1 Channel 7D 1300 nm, single-mode, Laser, 1 Channel 7E Channel 1 - G.703; Channel 2 - 820 nm, multimode 7F Channel 1 - G.703; Channel 2 - 1300 nm, multimode 7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED 7H 820 nm, multimode, LED, 2 Channels

7I 1300 nm, multimode, LED, 2 C hannels 7J 1300 nm, single-mode, ELED, 2 Channels 7K 1300 nm, single-mode, Laser, 2 Channels 7L Channel 1 - RS422; C hannel 2 - 820 nm, multimode, LED 7M Channel 1 - RS422; Channel 2 - 1300 nm, multimode, LED 7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED 7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, Laser 7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser 7R G.703, 1 Channel 7S G.703, 2 Channels 7T RS422, 1 Channel 7W RS422, 2 Channels

The order codes for the reduced size vertical mount units with the process bus module are shown below.

Table 2–7: F35 ORDER CODES (REDUCED SIZE VERTICAL UNITS WITH PROCESS BUS)

F35 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)

U | | | | | | | | RS485 and Two Multi-mode fiber 100Base-FX (SFP with LC), One 10/100Base-T (SFP with RJ45) V | | | | | | | | RS485 and Three 10/100Base-T (SFP with RJ45)

AW | | | | | | | CyberSentry Lvl 1 and IEC 61850 and PID cont roller

BW | | | | | | | IEEE 1588 and IEC 61850 and PID controller

CW | | | | | | | PRP, PID controller, and IEC 61850

D0 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 D1 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 a nd Ethernet Global Data (EGD) D3 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 a nd IEC 61850 D4 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 a nd IEC 61850 and Ethernet Global Data (EGD)

DW | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and I EC 61850 and PID controller

EW | | | | | | | IEEE 1588, PRP, PID controller, and IEC 61850

FW | | | | | | | PRP, CyberSentry Lvl 1, PID controller, and IEC 61850

G0 | | | | | | | IEEE 1588 and PRP G1 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and Ethernet Global Data G3 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, and IEC 61850 G4 | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, Ethernet Global Data, and IEC 61850

GW | | | | | | | IEEE 1588, PRP, CyberSentry Lvl 1, PID controller, and IEC 61850

JW | | | | | | | IEC 60870-5-103 + PID controller + IEC 61850

KW | | | | | | | IEEE1588 + PRP + IE C 60870-5-103 + PID controller + IEC 61850

LW | | | | | | | IEC 60870-5-103 + IEEE1588 + PRP + CyberSentry Lvl 1 + PID controller + IEC 61850

B | | | | | | Vertical (3/4 rack) with harsh environmental coating

D | | | | | French display R | | | | | Russian display A | | | | | Chinese display K | | | | | Enhanced front panel with English display M | | | | | Enhanced front panel with French display Q | | | | | Enhanced front panel with Russian display U | | | | | Enhanced front panel with Chinese display L | | | | | Enhanced front panel with English display and user-programmable pushbut tons N | | | | | Enhanced front panel with French display and user-programmable pushbuttons T | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons V | | | | | Enhanced front panel with Chinese display and user-programmable pushbut tons W | | | | | Enhanced front panel with Turkish display Y | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons

2-12 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.2 ORDER CODES

Table 2–7: F35 ORDER CODES (REDUCED SIZE VERTICAL UNITS WITH PROCESS BUS)

POWER SUPPLY H | | | | 125 / 250 V AC/DC power supply

CT/VT MODULES | 81 | | Eight-port digital process bus module DIGITAL INPUTS/OUTPUTS XX XX XX No Module

INTER-RELAY COMMUNICATIONS (select a maximum of 1 per unit) For the last module, slot P is used for digital and transducer input/output modules; slot R is used for inter-relay communications modules.

F35 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)

L | | | | 24 to 48 V (DC only) pow er supply

4A 4 Solid-State (no monitoring) MOSFET outputs 4B 4 Solid-State (voltage with optional current) MOSFET outputs 4C 4 Solid-State (current with optional voltage) MOSFET outputs 4D 16 digital inputs with Auto-Burnishing (maximum of three modules within a case) 4L 14 Form-A (no monitoring) Latching outputs 67 8 Form-A (no monit oring) outputs 6A 2 Form-A (voltage with optional current) and 2 For m-C outputs, 8 digital inputs 6B 2 Form-A (voltage with optional current) and 4 For m-C outputs, 4 digital inputs 6C 8 Form-C outputs 6D 16 digital inputs 6E 4 Form-C outputs, 8 digital inputs 6F 8 Fast Form-C outputs 6G 4 Form-A (voltage with optional current) outputs, 8 digital inputs 6H 6 Form-A (voltage with optional current) outputs, 4 digital inputs 6K 4 Form-C and 4 Fast Form-C outputs 6L 2 Form-A (curr ent with optional voltage) and 2 Form-C outputs, 8 digital inputs 6M 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs 6N 4 Form-A (current with optional voltage) outputs, 8 digital inputs 6P 6 Form-A (current with optional voltage) outputs, 4 digital inputs 6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs 6S 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digi tal inputs 6T 4 Form-A (no monitoring) out puts, 8 digital inputs 6U 6 Form-A (no monitoring) outputs, 4 digital inputs 6V 2 Form-A outputs, 1 Form-C output, 2 Form-A ( no monitoring) latching outputs, 8 digital inputs 2A C37.94SM, 1300 nm single-mode, ELED, 1 channel single-mode 2B C37.94SM, 1300 nm single-mode, ELED, 2 channel single-mode 2E Bi-phase, single channel 2F Bi-phase, dual channel 2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel 2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels

2I Channel 1 - IEEE C37.94, MM, 6 4/128 kbps; Channel 2 - 1300 nm, single-mode, Laser 2J Channel 1 - IEEE C37.94, MM, 64/128 kbps; Channel 2 - 1550 nm, single-mode, Laser 72 1550 nm, single-mode, Laser, 1 Channel 73 1550 nm, single-mode, Laser, 2 Channel 74 Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, Laser 75 Channel 1 - G.703; Channel 2 - 1550 nm, single-mode Laser 76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel 77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels 7A 820 nm, multimode, LED, 1 Channel 7B 1300 nm, multimode, LED, 1 Channel 7C 1300 nm, single-mode, ELED, 1 Channel 7D 1300 nm, single-mode, Laser, 1 Channel 7E Channel 1 - G.703; Channel 2 - 820 nm, multimode 7F Channel 1 - G.703; Channel 2 - 1300 nm, multimode 7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED 7H 820 nm, multimode, LED, 2 Channels

7I 1300 nm, multimode, LED, 2 Channels 7J 1300 nm, single-mode, ELED, 2 Channels 7K 1300 nm, single-mode, Laser, 2 Channels 7L Channel 1 - RS422; Channel 2 - 820 nm, multimode, LED 7M Channel 1 - RS422; Channel 2 - 1300 nm, multimode, LED 7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED 7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, Laser 7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser 7R G.703, 1 Channel 7S G.703, 2 Channels 7T RS422, 1 Channel 7W RS422, 2 Channels

GE Multilin F35 Multiple Feeder Protection System 2-13

2.2 ORDER CODES 2 PRODUCT DESCRIPTION

NOTE

2.2.4 REPLACEMENT MODULES

Replacement modules can be ordered separately. When ordering a replacement CPU module or faceplate, provide the serial number of your existing unit.

Not all replacement modules may be applicable to the F35 relay. Only the modules specified in the order codes are available as replacement modules.

Replacement module codes are subject to change without notice. See the ordering page at

http://www.gegridsolutions.com/multilin/order.htm

for the latest options.

The replacement module order codes for the horizontal mount units are shown below.

Table 2–8: ORDER CODES FOR REPLACEMENT MODULES, HORIZONTAL UNITS

POWER SUPPLY redundant supply only available in horizontal units and must be same type as main supply, for example must swap both power supplies when switching from RH to SH CPU | T | RS485 with 3 100Base-FX Ethernet, multimode, SFP with LC

FACEPLATE/DISPLAY | 3C | Horizontal faceplate with keypad and English display

CONTACT INPUTS AND OUTPUTS | 4A | 4 Solid-State (no monitoring) MOSFET outputs

CT/VT MODULES (NOT AVAILABLE FOR THE C30)

INTER-RELAY COMMUNICATIONS | 2A | C37.94SM, 1300 nm single-mode, ELED, 1 channel single-mode

TRANSDUCER INPUTS/OUTPUTS

UR - ** - *

| SH A | 125 / 300 V AC/DC

| SL H | 24 to 48 V (DC only)

| U | RS485 with 1 100Base-T Ethernet, SFP RJ-45 + 2 100Base-FX Ethernet, multimode, SFP with LC | V | RS485 with 3 100Base-T Ethernet, SFP with RJ-45

| 3D | Horizontal faceplate with keypad and French display | 3R | Horizontal faceplate with keypad and Russian display | 3A | Horizontal faceplate with keypad and Chinese display | 3P | Horizontal faceplate with keypad, user-programmable pushbuttons, and English display | 3G | Horizontal faceplate with keypad, user-p rogrammable pushbuttons, and French display | 3S | Horizontal faceplate with keypad, user-programmable pushbuttons, and Russian display | 3B | Horizontal faceplate with keypad, user-programmable pushbuttons, and Chinese display | 3K | Enhanced front panel with English display | 3M | Enhanced front panel with French display | 3Q | Enhanced front panel wit h Russian display | 3U | Enhanced front panel with Chinese display | 3L | Enhanced front panel with English display and user-programmable pushbuttons | 3N | Enhanced front panel with French display and user-programmable pushbuttons | 3T | Enhanced front panel with Russian display an d user-programmable pushbuttons | 3V | Enhanced front panel with Chinese display and user-programmable pushbuttons | 3I | Enhanced front panel with German display | 3J | Enhanced front panel with German display and user-programmable pushbuttons

| 4B | 4 Solid-State (voltage with optional current) MOSFET outputs | 4C | 4 Solid-State (current with optional voltage) MOSFET outputs | 4D | 16 contact inputs with Auto-Burnishing | 4L | 14 Form-A (no monitoring) Latching outputs | 67 | 8 Form-A (no monitoring) outputs | 6A | 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 contact inputs | 6B | 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 contact inputs | 6C | 8 Form-C outputs | 6D | 16 contact inputs | 6E | 4 Form-C outputs, 8 contact inputs | 6F | 8 Fast For m-C outputs | 6G | 4 Form-A (voltage with optional current) outputs, 8 contact inputs | 6H | 6 Form-A (voltage with optional current) outputs, 4 contact inputs | 6K | 4 Form-C and 4 Fast Form-C outpu ts | 6L | 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 contact inputs | 6M | 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 contact inputs | 6N | 4 Form-A (current with optional voltage) outputs, 8 contact inputs | 6P | 6 Form-A (current with optional voltage) outputs, 4 contact inputs | 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 contact inputs | 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 contact inputs | 6T | 4 Form-A (no monitoring) outputs, 8 contact inputs | 6U | 6 Form-A (no monitoring) outputs, 4 contact inputs | 6V | 2 Form-A outputs, 1 Form-C output , 2 Form-A (no monitoring) latching outputs, 8 contact inputs | 8L | Standard 4CT/4VT with enhanced diagnostics | 8N | Standard 8CT with enhanced diagnostics | 8M | Sensitive Ground 4CT/4VT with enhanced diagnostics | 8R | Sensitive Ground 8CT with enhanced diagnostics | 8V | Standard 8VT with enhanced diagnostics

| 2B | C37.94SM, 1300 nm single-mode, ELED, 2 channel single-mode | 2E | Bi-phase, single channel | 2F | Bi-phase, du al channel | 2G | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel | 2H | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels | 2I | Channel 1 - IEEE C37.94, mult imode, 64/128 kbps; Channel 2 - 1300 nm, single-mode, Laser | 2J | Channel 1 - IEEE C37.94, multimode, 64/128 kbps; Channel 2 - 1550 nm, single-mode, Laser | 72 | 1550 nm, single-mode, Laser, 1 Channel | 73 | 1550 nm, single-mode, Laser, 2 Channel | 74 | Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, Laser | 75 | Channel 1 - G.703; Channel 2 - 1550 nm, single-mode Laser | 76 | IEEE C37.94, 820 nm, multimode, LED, 1 Channel | 77 | IEEE C37.94, 820 nm, multimode, LED, 2 Channels | 7A | 820 nm, multimode, LED, 1 Channel | 7B | 1300 nm, multimode, LED, 1 Channel | 7C | 1300 nm, single-mode, ELED, 1 Channel | 7D | 1300 nm, single-mode, Laser, 1 Channel | 7E | Channel 1 - G.703; Channel 2 - 820 nm, multimode | 7F | Channel 1 - G.703; Channel 2 - 1300 nm, multimode | 7G | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED | 7H | 820 nm, multimode, LED, 2 Channels | 7I | 1300 nm, multimode, LED, 2 Channel s | 7J | 1300 nm, single-mode, ELED, 2 Channels | 7K | 1300 nm, single-mode, Laser, 2 Channels | 7L | Channel 1 - RS422; Channel 2 - 820 nm, multimode, LED | 7M | Channel 1 - RS422; Channel 2 - 1300 nm, multimode, LED | 7N | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED | 7P | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, Laser | 7Q | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser | 7R | G.703, 1 Channel | 7S | G.703, 2 Channels | 7T | RS422, 1 Chan nel | 7W | RS422, 2 Channels | 5A | 4 DCmA inputs, 4 DCmA outputs (only one 5A module is allowed) | 5C | 8 RTD inputs | 5D | 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed) | 5E | 4 DCmA inputs, 4 RTD inputs | 5F | 8 DCmA inputs

The replacement module order codes for the reduced-size vertical mount units are shown below.

2-14 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.2 ORDER CODES

Table 2–9: ORDER CODES FOR REPLACEMENT MODULES, VERTICAL UNITS

POWER SUPPLY | SH B | 125 / 300 V AC/DC

CPU | T | RS485 with 3 100Base-FX Ethernet, multimode, SFP with LC

FACEPLATE/DISPLAY | 3F | Vertical faceplate with keypad and English display

CONTACT INPUTS/OUTPUTS | 4A | 4 Solid-State (no monitoring) MOSFET outputs

CT/VT MODULES (NOT AVAILABLE FOR THE C30)

INTER-RELAY COMMUNICATIONS | 2A | C37.94SM, 1300 nm single-mode, ELED, 1 channel single-mode

TRANSDUCER INPUTS/OUTPUTS

UR - ** - *

| SL V | 24 to 48 V (DC only)

| U | RS485 with 1 100Base-T Ethernet, SFP RJ-45 + 2 100Base-FX Ethernet, multimode, SFP with LC | V | RS485 with 3 100Base-T Ethernet, SFP with RJ-45

| 3D | Vertical faceplate with keypad and French display | 3R | Vertical faceplate with keypad and Russian display | 3A | Vertical faceplate with keypad and Chinese display | 3K | Enhanced front panel with English display | 3M | Enhanced front panel with French display | 3Q | Enhanced front panel wit h Russian display | 3U | Enhanced front panel with Chinese display | 3L | Enhanced front panel with English display and user-programmable pushbuttons | 3N | Enhanced front panel with French display and user-programmable pushbuttons | 3T | Enhanced front panel with Russian display an d user-programmable pushbuttons | 3V | Enhanced front panel with Chinese display and user-programmable pushbuttons | 3I | Enhanced front panel with German display | 3J | Enhanced front panel with German display and user-programmable pushbuttons

| 4B | 4 Solid-State (voltage with optional current) MOSFET outputs | 4C | 4 Solid-State (current with optional voltage) MOSFET outputs | 4D | 16 contact inputs with Auto-Burnishing | 4L | 14 Form-A (no monitoring) Latching outputs | 67 | 8 Form-A (no monitoring) outputs | 6A | 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 contact inputs | 6B | 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 contact inputs | 6C | 8 Form-C outputs | 6D | 16 contact inputs | 6E | 4 Form-C outputs, 8 contact inputs | 6F | 8 Fast For m-C outputs | 6G | 4 Form-A (voltage with optional current) outputs, 8 contact inputs | 6H | 6 Form-A (voltage with optional current) outputs, 4 contact inputs | 6K | 4 Form-C and 4 Fast Form-C outpu ts | 6L | 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 contact inputs | 6M | 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 contact inputs | 6N | 4 Form-A (current with optional voltage) outputs, 8 contact inputs | 6P | 6 Form-A (current with optional voltage) outputs, 4 contact inputs | 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 contact inputs | 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 contact inputs | 6T | 4 Form-A (no monitoring) outputs, 8 contact inputs | 6U | 6 Form-A (no monitoring) outputs, 4 contact inputs | 6V | 2 Form-A outputs, 1 Form-C outpu t, 2 Form-A (no monitoring) latching outputs, 8 contact inputs | 8L | Standard 4CT/4VT with enhanced diagnostics | 8N | Standard 8CT with enhanced diagnostics | 8R | Sensitive Ground 8CT with enhanced diagnostics | 8V | Standard 8VT with enhanced diagnostics

| 2B | C37.94SM, 1300 nm single-mode, ELED, 2 channel single-mode | 2E | Bi-phase, single channel | 2F | Bi-phase, du al channel | 2G | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel | 2H | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels | 2I | Channel 1 - IEEE C37.94, mult imode, 64/128 kbps; Channel 2 - 1300 nm, single-mode, Laser | 2J | Channel 1 - IEEE C37.94, multimode, 64/128 kbps; Channel 2 - 1550 nm, single-mode, Laser | 72 | 1550 nm, single-mode, Laser, 1 Channel | 73 | 1550 nm, single-mode, Laser, 2 Channel | 74 | Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, Laser | 75 | Channel 1 - G.703; Channel 2 - 1550 nm, single-mode Laser | 76 | IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel | 77 | IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels | 7A | 820 nm, multimode, LED, 1 Channel | 7B | 1300 nm, multimode, LED, 1 Channel | 7C | 1300 nm, single-mode, ELED, 1 Channel | 7D | 1300 nm, single-mode, Laser, 1 Channel | 7E | Channel 1 - G.703; Channel 2 - 820 nm, multimode | 7F | Channel 1 - G.703; Channel 2 - 1300 nm, multimode | 7G | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED | 7H | 820 nm, multimode, LED, 2 Channels | 7I | 1300 nm, multimode, LED, 2 Channel s | 7J | 1300 nm, single-mode, ELED, 2 Channels | 7K | 1300 nm, single-mode, Laser, 2 Channels | 7L | Channel 1 - RS422; Channel 2 - 820 nm, multimode, LED | 7M | Channel 1 - RS422; Channel 2 - 1300 nm, multimode, LED | 7N | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED | 7P | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, Laser | 7Q | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser | 7R | G.703, 1 Channel | 7S | G.703, 2 Channels | 7T | RS422, 1 Chan nel | 7W | RS422, 2 Channels | 5A | 4 DCmA inputs, 4 DCmA outputs (only one 5A module is allowed) | 5C | 8 RTD inputs | 5D | 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed) | 5E | 4 DCmA inputs, 4 RTD inputs | 5F | 8 DCmA inputs

GE Multilin F35 Multiple Feeder Protection System 2-15

2.3 SIGNAL PROCESSING 2 PRODUCT DESCRIPTION

From

CT/VT

Analog Inputs

Analog low-

pass filter

Analog-to-

Digital

Converter

Digital band-

pass filter

DSP module

Phasor

estimation

½ cycle

Fourier

1 cycle

Fourier

RMS

values

Fundamen

tal freq.

Phasors,

Seq. com-

ponents

Sampling

frequency

CPU module

I> Z< U<

Protection

algorithms

IRIG-B

IEEE 1588 SNTP

Tracking frequency selection,

estimation

Accurate

Real-Time

clock

Synchrophasors

calculations

Serial ports

Ethernet ports

Communi-

cation

protocols

Control

elements,

monitoring

elements, FlexLogic,

Aggregation, post-filtering

Contact Inputs

module

HMI

Ddebounce

filtering

Optoisolated

Analog Inputs

module

DCmA, RTD

Inter-relay

comms

module

Channel

monitoring

CRC check

G.703, RS-422,

C37.94, direct fiber

Contact Outputs

module

Serial

PMU (IEEE C37.118,

IEC 61850-90-5)

IEC 61850 (GOOSE,

MMS Server)

DNP, Modbus,

IEC60870

Comtrade, data

logger

Events

Inter-relay

comms module

Frequency

Analog Outputs

module

Time stamping

Synchrophasors filtering

859740A1.vsd

2± 260 V()⋅

2.3SIGNAL PROCESSING 2.3.1 UR SIGNAL PROCESSING

The UR series relays are microprocessor-based protective relays that are designed to measure power system conditions directly via CT and PT inputs and via other sources of information, such as analog inputs, communications inputs and contact inputs. The following figure shows the overall signal processing in URs.

An analog low pass anti-aliasing filter with a 3 dB corner frequency is set at 2.4 kHz and is used for current and voltage analog filtering as well as signal conditioning. The same filtering is applied for phase, ground currents, phase-to-phase

(when applicable), and auxiliary voltages. The 2.4 kHz cut-off frequency applies to both 50 Hz and 60 Hz applications and fixed in the hardware, and thus is not dependent on the system nominal frequency setting.

The UR samples its AC signals at 64 samples per cycle, that is, at 3840 Hz in 60 Hz systems, and 3200 Hz in 50 Hz systems. The sampling rate is dynamically adjusted to the actual system frequency by an accurate and fast frequency tracking system.

Figure 2–3: UR SIGNAL PROCESSING

The A/D converter has the following ranges of AC signals: Voltages:

(EQ 2.1)

Currents:

2-16 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.3 SIGNAL PROCESSING

2± 46rated A()⋅

RMS t()

---

t() td

tT–()



(EQ 2.2)

Current harmonics are estimated based on raw samples with the use of the full-cycle Fourier filter. Harmonics 2nd through 25th are estimated.

True RMS value for the current is calculated on a per-phase basis. The true RMS can be used for demand recording or as an input signal to Time Overcurrent function, if the latter is intended for thermal protection. The true RMS is calculated as per the widely accepted definition:

(EQ 2.3)

RMS values include harmonics, inter-harmonics, DC components, and so on, along with fundamental frequency values. The true RMS value reflects thermal effects of the current and is used for the thermal related monitoring and protection functions.

Protection and control functions respond to phasors of the fundamental and/or harmonic frequency components (magnitudes and angles), with an exception for some functions that have an option for RMS or fundamental measurements, or some function responding to RMS only. This type of response is explained typically in each element's section in the instruction manual.

Currents are pre-filtered using a Finite Impulse Response (FIR) digital filter. The filter is designed to reject DC components and low-frequency distortions, without amplifying high-frequency noise. This filter is referred to as a modified MIMIC filter, which provides excellent filtering and overall balance between speed and accuracy of filtering. The filter is cascaded with the full-cycle Fourier filter for the current phasor estimation.

Voltages are pre-filtered using a patented Finite Impulse Response (FIR) digital filter. The filter has been optimized to reject voltage transformers specific distortions, such as Capacitive Voltage Transformer (CVT) noise and high-frequency oscillatory components. The filter is cascaded with the half-cycle Fourier filter for the voltage phasor estimation.

The URs measure power system frequency using the Clarke transformation by estimating the period of the waveform from two consecutive zero-crossings in the same direction (negative-to-positive). Voltage or current samples are pre-filtered using a Finite Impulse Response (FIR) digital filter to remove high frequency noise contained in the signal. The period is used after several security conditions are met, such as true RMS signal must be above 6% nominal for a certain time and others. If these security conditions are not met, the last valid measurement is used for a specific time after which the UR reverts to nominal system frequency.

Synchrophasors are calculated using a patented convolution integral algorithm. This algorithm allows use of the same time stamped samples, which are used for protection and taken at the same sampling frequency. This allows URs to use one sampling clock for both protection algorithms and synchrophasors.

Synchrophasors on firmware versions 7.23 and up have been tested and certified to meet IEEE C.37.118-2011 and C.37.118.1a-2014 standards for both metering and protection classes with outputs available up to 60 synchrophasors per second for the metering class and 120 synchrophasors per second for the protection class. Synchrophasors measurement are also available via IEC 61850-90-5 protocol.

Contact inputs threshold is settable in the firmware with 17, 33, 84, 166 VDC settings available. Inputs are scanned every

0.5 ms and can be conditioned for the critical applications, using debounce time timer, settable from 0.0 ms to 16.0 ms. Contact inputs with auto-burnishing are available as well, when external contacts are exposed to the contamination in a harsh industrial environment.

All measured values are available in the UR metering section on the front panel and via communications protocols. Measured analog values and binary signals can be captured in COMTRADE format with sampling rates from 8 to 64 samples per power cycle. Analog values can be captured with Data Logger, allowing much slower rates extended over long period of time.

Other advanced UR order code options are available to support IEC 61850 Ed2.0 (including fast GOOSE, MMS server, 61850 services, ICD/CID/IID files, and so on), IEEE 1588 (IEEE C37.238 power profile) based time synchronization, CyberSentry (advanced cyber security), the Parallel Redundancy Protocol (PRP), IEC 60870-5-103, and so on.

GE Multilin F35 Multiple Feeder Protection System 2-17

2.4 SPECIFICATIONS 2 PRODUCT DESCRIPTION

NOTE

2.4SPECIFICATIONSSPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

The operating times include the activation time of a trip rated form-A output contact unless otherwise indicated. FlexLogic operands of a given element are 4 ms faster. Take this into account when using FlexLogic to interconnect with other protection or control elements of the relay, building FlexLogic equations, or interfacing with other IEDs or

PHASE/NEUTRAL/GROUND TOC

Current: Phasor or RMS Pickup level: 0.000 to 30.000 pu in steps of 0.001 Dropout level: 97% to 98% of pickup Level accuracy:

Curve shapes: IEEE Moderately/Very/Extremely

Curve multiplier: Time Dial = 0.00 to 600.00 in steps of

Reset type: Instantaneous/Timed (per IEEE) Curve timing accuracy at 1.03 to 20 x pickup: ±3.5% of operate time or ±½ cycle

Voltage restraint: modifies pickup current for voltage in the

power system devices via communications or different output contacts. If not specified, the operate times given here are for a 60 Hz system at nominal system frequency. Operate times for a 50 Hz system are 1.2 times longer.

NEGATIVE SEQUENCE TOC

Pickup level: 0.000 to 30.000 pu in steps of 0.001 Dropout level: 97% to 98% of pickup Level accuracy: ±0.5% of reading or ±0.4% of rated

0.1 to 2.0 × CT: ±0.5% of reading or ±0.4% of rated (whichever is greater)

> 2.0 × CT: ±1.5% of reading > 2.0 × CT rating

Inverse; IEC (and BS) A/B/C and Short Inverse; GE IAC Inverse, Short/Very/ Extremely Inverse; I (programmable); Definite Time (0.01 s base curve)

0.01

(whichever is greater) from pickup to operate

range of 0.1<V<0.9 VT Nominal in a fixed linear relationship

t; FlexCurves™

Curve shapes: IEEE Moderately/Very/Extremely

Curve multiplier (Time dial): 0.00 to 600.00 in steps of 0.01 Reset type: Instantaneous/Timed (per IEEE) and Lin-

Curve timing accuracy at 1.03 to 20 x pickup: ±3.5% of operate time or ±½ cycle

NEGATIVE SEQUENCE IOC

Pickup level: 0.000 to 30.000 pu in steps of 0.001 Dropout level: 97 to 98% of pickup Level accuracy: 0.1 to 2.0 × CT rating: ±0.5% of reading

PHASE/NEUTRAL/GROUND IOC

Pickup level: 0.000 to 30.000 pu in steps of 0.001 Dropout level: 97 to 98% of pickup Level accuracy:

0.1 to 2.0 × CT rating: ±0.5% of reading or ±0.4% of rated (whichever is greater)

> 2.0 × CT rating ±1.5% of reading Overreach: <2% Pickup delay: 0.00 to 600.00 s in steps of 0.01 Reset delay: 0.00 to 600.00 s in steps of 0.01 Operate time: <16 ms at 3 × pickup at 60 Hz

(Phase/Ground IOC) <20 ms at 3 × pickup at 60 Hz (Neutral IOC)

Timer accuracy: ±3% of operate time or ±1/4 cycle

(whichever is greater)

Overreach: <2% Pickup delay: 0.00 to 600.00 s in steps of 0.01 Reset delay: 0.00 to 600.00 s in steps of 0.01 Operate time: <20 ms at 3 × pickup at 60 Hz Timer accuracy: ±3% of operate time or ±1/4 cycle

WATTMETRIC ZERO-SEQUENCE DIRECTIONAL

Measured power: zero-sequence Number of elements: 4 Characteristic angle: 0 to 360° in steps of 1 Minimum power: 0.001 to 1.200 pu in steps of 0.001 Pickup level accuracy: ±1% or ±0.0025 pu, whichever is greater Hysteresis: 3% or 0.001 pu, whichever is greater Pickup delay: definite time (0 to 600.00 s in steps of

Inverse time multiplier: 0.01 to 2.00 s in steps of 0.01 Curve timing accuracy: ±3.5% of operate time or ±1 cycle

Operate time: <30 ms at 60 Hz

2.4.1 PROTECTION ELEMENTS

(whichever is greater) from 0.1 to 2.0 x CT rating ±1.5% of reading > 2.0 x CT rating

Inverse; IEC (and BS) A/B/C and Short Inverse; GE IAC Inverse, Short/Very/ Extremely Inverse; I (programmable); Definite Time (0.01 s base curve)

ear

(whichever is greater) from pickup to operate

or ±0.4% of rated (whichever is greater); > 2.0 × CT rating: ±1.5% of reading

(whichever is greater)

0.01), inverse time, or FlexCurve

(whichever is greater) from pickup to operate

t; FlexCurves™

2-18 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.4 SPECIFICATIONS

PHASE UNDERVOLTAGE

Pickup level: 0.000 to 3.000 pu in steps of 0.001 Dropout level: 102 to 103% of pickup Level accuracy: ±0.5% of reading from 10 to 208 V Curve shapes: GE IAV Inverse;

Definite Time (0.1s base curve)

Curve multiplier: Time dial = 0.00 to 600.00 in steps of

0.01 Curve timing accuracy at <0.90 x pickup: ±3.5% of operate time or ±1/2 cycle

(whichever is greater) from pickup to operate

AUXILIARY UNDERVOLTAGE

Pickup level: 0.000 to 3.000 pu in steps of 0.001 Dropout level: 102 to 103% of pickup Level accuracy: ±0.5% of reading from 10 to 208 V Curve shapes: GE IAV Inverse, Definite Time Curve multiplier: Time Dial = 0 to 600.00 in steps of 0.01 Curve timing accuracy at <0.90 x pickup: ±3.5% of operate time or ±1/2 cycle

(whichever is greater) from pickup to operate

NEUTRAL OVERVOLTAGE

Pickup level: 0.000 to 3.000 pu in steps of 0.001 Dropout level: 97 to 98% of pickup Level accuracy: ±0.5% of reading from 10 to 208 V Pickup delay: 0.00 to 600.00 s in steps of 0.01 (definite

time) or user-defined curve Reset delay: 0.00 to 600.00 s in steps of 0.01 Curve timing accuracy at >1.1 x pickup: ±3.5% of operate time or ±1 cycle

(whichever is greater) from pickup to

operate Operate time: <30 ms at 1.10 × pickup at 60 Hz

AUXILIARY OVERVOLTAGE

Pickup level: 0.000 to 3.000 pu in steps of 0.001 Dropout level: 97 to 98% of pickup Level accuracy: ±0.5% of reading from 10 to 208 V Pickup delay: 0 to 600.00 s in steps of 0.01 Reset delay: 0 to 600.00 s in steps of 0.01 Timer accuracy: ±3% of operate time or ±1/4 cycle

(whichever is greater) Operate time: <30 ms at 1.10 × pickup at 60 Hz

UNDERFREQUENCY

Minimum signal: 0.10 to 1.25 pu in steps of 0.01 Pickup level: 20.00 to 65.00 Hz in steps of 0.01 Dropout level: pickup + 0.03 Hz Level accuracy: ±0.001 Hz Time delay: 0 to 65.535 s in steps of 0.001 Timer accuracy: ±3% of operate time or ±1/4 cycle

(whichever is greater)

Operate time: typically 4 cycles at 0.1 Hz/s change

Typical times are average operate times including variables such as frequency change instance, test method, etc., and may vary by ±0.5 cycles.

typically 3.5 cycles at 0.3 Hz/s change typically 3 cycles at 0.5 Hz/s change

BREAKER ARCING CURRENT

Principle: accumulates breaker duty (I2t) and mea-

Initiation: programmable per phase from any Flex-

Compensation for auxiliary relays: 0 to 65.535 s in steps of 0.001 Alarm threshold: 0 to 50000 kA Fault duration accuracy: 0.25 of a power cycle Availability: 1 per CT bank with a minimum of 2

sures fault duration

Logic operand

-cycle in steps of 1

BREAKER RESTRIKE

Principle: detection of high-frequency overcurrent

Availability: one per CT/VT module (not including 8Z

Pickup level: 0.1 to 2.00 pu in steps of 0.01 Reset delay: 0.000 to 65.535 s in steps of 0.001

condition ¼ cycle after breaker opens

modules)

INCIPIENT CABLE FAULT DETECTION

Principle: detection of ½ cycle or less overcurrent

condition during normal load

Availability: two per CT/VT module (not including 8Z

modules) Pickup level: 0.1 to 10.00 pu in steps of 0.01 Reset delay: 0.000 to 65.535 s in steps of 0.001 Operating mode: number of counts, counts per time win-

dow

AUTORECLOSURE

Single breaker applications, 3-pole tripping schemes Up to 4 reclose attempts before lockout Independent dead time setting before each shot Possibility of changing protection settings after each shot with

FlexLogic

THERMAL OVERLOAD PROTECTION

Thermal overload curves: IEC 255-8 curve Base current: 0.20 to 3.00 pu in steps of 0.01 Overload (k) factor: 1.00 to 1.20 pu in steps of 0.05 Trip time constant: 0 to 1000 min. in steps of 1 Reset time constant: 0 to 1000 min. in steps of 1 Minimum reset time: 0 to 1000 min. in steps of 1 Timer accuracy (cold curve): ±100 ms or 2%, whichever is greater Timer accuracy (hot curve): ±500 ms or 2%, whichever is greater

< 0.9 × k × Ib and I / (k × Ib) > 1.1

for I

GE Multilin F35 Multiple Feeder Protection System 2-19

2.4 SPECIFICATIONS 2 PRODUCT DESCRIPTION

TRIP BUS (TRIP WITHOUT FLEXLOGIC)

Number of elements: 6 Number of inputs: 16 Operate time: <2 ms at 60 Hz Timer accuracy: ±3% or 10 ms, whichever is greater

FLEXLOGIC

Programming language: Reverse Polish Notation with graphical

visualization (keypad programmable) Lines of code: 512 Internal variables: 64 Supported operations: NOT, XOR, OR (2 to 16 inputs), AND (2

to 16 inputs), NOR (2 to 16 inputs),

NAND (2 to 16 inputs), latch (reset-domi-

nant), edge detectors, timers Inputs: any logical variable, contact, or virtual

input Number of timers: 32 Pickup delay: 0 to 60000 (ms, sec., min.) in steps of 1 Dropout delay: 0 to 60000 (ms, sec., min.) in steps of 1

FLEXCURVES™

Number: 4 (A through D) Reset points: 40 (0 through 1 of pickup) Operate points: 80 (1 through 20 of pickup) Time delay: 0 to 65535 ms in steps of 1

FLEX STATES

Number: up to 256 logical variables grouped

under 16 Modbus addresses Programmability: any logical variable, contact, or virtual

input

FLEXELEMENTS™

Number of elements: 16 Operating signal: any analog actual value, or two values in

differential mode Operating signal mode: signed or absolute value Operating mode: level, delta Comparator direction: over, under Pickup Level: –90.000 to 90.000 pu in steps of 0.001 Hysteresis: 0.1 to 50.0% in steps of 0.1 Delta dt: 20 ms to 60 days Pickup & dropout delay: 0.000 to 65.535 s in steps of 0.001

NON-VOLATILE LATCHES

Type: set-dominant or reset-dominant Number: 16 (individually programmed) Output: stored in non-volatile memory Execution sequence: as input prior to protection, control, and

FlexLogic

USER-PROGRAMMABLE LEDs

Number: 48 plus trip and alarm Programmability: from any logical variable, contact, or vir-

tual input Reset mode: self-reset or latched

2.4.2 USER-PROGRAMMABLE ELEMENTS

LED TEST

Initiation: from any contact input or user-program-

mable condition Number of tests: 3, interruptible at any time Duration of full test: approximately 3 minutes Test sequence 1: all LEDs on Test sequence 2: all LEDs off, one LED at a time on for 1 s Test sequence 3: all LEDs on, one LED at a time off for 1 s

USER-DEFINABLE DISPLAYS

Number of displays: 16 Lines of display: 2 × 20 alphanumeric characters Parameters: up to 5, any Modbus register addresses Invoking and scrolling: keypad, or any user-programmable con-

dition, including pushbuttons

CONTROL PUSHBUTTONS

Number of pushbuttons: 7 Operation: drive FlexLogic operands

USER-PROGRAMMABLE PUSHBUTTONS (OPTIONAL)

Number of pushbuttons: 12 (standard faceplate);

16 (enhanced faceplate) Mode: self-reset, latched Display message: 2 lines of 20 characters each Drop-out timer: 0.00 to 60.00 s in steps of 0.05 Autoreset timer: 0.2 to 600.0 s in steps of 0.1 Hold timer: 0.0 to 10.0 s in steps of 0.1

SELECTOR SWITCH

Number of elements: 2 Upper position limit: 1 to 7 in steps of 1 Selecting mode: time-out or acknowledge Time-out timer: 3.0 to 60.0 s in steps of 0.1 Control inputs: step-up and 3-bit Power-up mode: restore from non-volatile memory or syn-

chronize to a 3-bit control input or synch/

restore mode

8-BIT SWITCH

Number of elements: 6 Input signals: two 8-bit integers via FlexLogic oper-

ands Control signal: any FlexLogic operand Response time: < 8 ms at 60 Hz, < 10 ms at 50 Hz

DIGITAL ELEMENTS

Number of elements: 48 Operating signal: any FlexLogic operand Pickup delay: 0.000 to 999999.999 s in steps of 0.001 Dropout delay: 0.000 to 999999.999 s in steps of 0.001 Timing accuracy: ±3% or ±4 ms, whichever is greater

2-20 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.4 SPECIFICATIONS

2.4.3 MONITORING

OSCILLOGRAPHY

Maximum records: 64 Sampling rate: 64 samples per power cycle Triggers: any element pickup, dropout, or operate;

contact input change of state; contact output change of state; FlexLogic equation

Data: AC input channels; element state; con-

tact input state; contact output state

Data storage: in non-volatile memory

EVENT RECORDER

Capacity: 1024 events Time-tag: to 1 microsecond Triggers: any element pickup, dropout, or operate;

contact input change of state; contact output change of state; self-test events

Data storage: in non-volatile memory

DATA LOGGER

Number of channels: 1 to 16 Parameters: any available analog actual value Sampling rate: 15 to 3600000 ms in steps of 1 Trigger: any FlexLogic operand Mode: continuous or triggered Storage capacity: (NN is dependent on memory)

1-second rate:

01 channel for NN days

16 channels for NN days

↓

60-minute rate:

01 channel for NN days 16 channels for NN days

FAULT LOCATOR

Number of independent fault locators: 1 per CT bank (to a maxi-

mum of 5) Method: single-ended Voltage source: wye-connected VTs, delta-connected

VTs and neutral voltage, delta-connected

VTs and zero-sequence current (approxi-

mation) Maximum accuracy if: fault resistance is zero or fault currents

from all line terminals are in phase Relay accuracy: ±1.5% (V > 10 V, I > 0.1 pu) Worst-case accuracy: VT CT Z METHOD RELAY ACCURACY

+ user data

%error

+ user data

%error

Line%error

+ user data

+ see chapter 8

%error

+ (1.5%)

2.4.4 METERING

RMS CURRENT: PHASE, NEUTRAL, AND GROUND

Accuracy at

0.1 to 2.0 × CT rating: ±0.25% of reading or ±0.1% of rated (whichever is greater)

> 2.0 × CT rating: ±1.0% of reading

RMS VOLTAGE

Accuracy: ±0.5% of reading from 10 to 208 V

REAL POWER (WATTS)

Accuracy at 0.1 to 1.5 x CT rating and 0.8 to

1.2 x VT rating: ±1.0% of reading at –1.0 ≤ PF< –0.8 and

0.8 < PF ≤ 10

REACTIVE POWER (VARS)

Accuracy at 0.1 to 1.5 x CT rating and 0.8 to

1.2 x VT rating: ±1.0% of reading at –0.2 ≤ PF ≤ 0.2

APPARENT POWER (VA)

Accuracy at 0.1 to 1.5 x CT rating and 0.8 to

1.2 x VT rating: ±1.0% of reading

WATT-HOURS (POSITIVE AND NEGATIVE)

Accuracy: ±2.0% of reading Range: ±0 to 1 × 10 Parameters: three-phase only Update rate: 50 ms

MWh

VAR-HOURS (POSITIVE AND NEGATIVE)

Accuracy: ±2.0% of reading Range: ±0 to 1 × 10 Parameters: three-phase only Update rate: 50 ms

Mvarh

GE Multilin F35 Multiple Feeder Protection System 2-21

2.4 SPECIFICATIONS 2 PRODUCT DESCRIPTION

VOLTAGE HARMONICS

Harmonics: 2nd to 25th harmonic: per phase, dis-

played as a % of f quency phasor) THD: per phase, displayed as a % of f

Accuracy:

HARMONICS: 1. f

THD: 1. f1 > 0.4pu: (0.25% + 0.035% / harmonic) of

> 0.4pu: (0.20% + 0.035% / harmonic) of

reading or 0.15% of 100%, whichever is greater

2. f

< 0.4pu: as above plus %error of f

reading or 0.20% of 100%, whichever is greater

2. f

< 0.4pu: as above plus %error of f

(fundamental fre-

AC CURRENT

CT rated primary: 1 to 50000 A CT rated secondary: 1 A or 5 A by connection Relay burden: < 0.2 VA at rated secondary Conversion range:

Standard CT: 0.02 to 46 × CT rating RMS symmetrical Sensitive Ground CT module:

0.002 to 4.6 × CT rating RMS symmetrical

Current withstand: 20 ms at 250 times rated

1 sec at 100 times rated continuous 4xInom Short circuit rating:150000 RMS symmetrical amperes, 250 V maximum (primary current to external CT)

AC VOLTAGE

VT rated secondary: 50.0 to 240.0 V VT ratio: 1.00 to 24000.00 Relay burden: < 0.25 VA at 120 V Conversion range: 1 to 275 V Voltage withstand: continuous at 260 V to neutral

1 min/hr at 420 V to neutral

FREQUENCY

Nominal frequency setting:25 to 60 Hz Sampling frequency: 64 samples per power cycle Tracking frequency range:20 to 70 Hz

CONTACT INPUTS

Dry contacts: 1000 Ω maximum Wet contacts: 300 V DC maximum Selectable thresholds: 17 V, 33 V, 84 V, 166 V Tolerance: ±10% Contacts per common return: 4 Recognition time: < 1 ms Debounce time: 0.0 to 16.0 ms in steps of 0.5 Continuous current draw:4 mA (when energized)

FREQUENCY

Accuracy at

V = 0.8 to 1.2 pu: ±0.001 Hz (when voltage signal is used

I = 0.1 to 0.25 pu: ±0.005 Hz I > 0.25 pu: ±0.02 Hz (when current signal is used for

for frequency measurement)

frequency measurement)

DEMAND

Measurements: Phases A, B, and C present and maxi-

mum measured currents 3-Phase Power (P, Q, and S) present and maximum measured currents

Accuracy: ±2.0%

2.4.5 INPUTS

CONTACT INPUTS WITH AUTO-BURNISHING

Dry contacts: 1000 Ω maximum Wet contacts: 300 V DC maximum Selectable thresholds: 17 V, 33 V, 84 V, 166 V Tolerance: ±10% Contacts per common return: 2 Recognition time: < 1 ms Debounce time: 0.0 to 16.0 ms in steps of 0.5 Continuous current draw:4 mA (when energized) Auto-burnish impulse current: 50 to 70 mA Duration of auto-burnish impulse: 25 to 50 ms

DCMA INPUTS

Current input (mA DC): 0 to –1, 0 to +1, –1 to +1, 0 to 5, 0 to 10,

Input impedance: 379 Ω ±10% Conversion range: –1 to + 20 mA DC Accuracy: ±0.2% of full scale Type: Passive

0 to 20, 4 to 20 (programmable)

RTD INPUTS

Types (3-wire): 100 Ω Platinum, 100 & 120 Ω Nickel, 10

Sensing current: 5 mA Range: –50 to +250°C Accuracy: ±2°C Isolation: 36 V pk-pk

Ω Copper

IRIG-B INPUT

IRIG formats accepted: B000…B007, B120…B127 IRIG control bits: IEEE Std C37.118.1-2011 Amplitude modulation: 1 to 10 V pk-pk DC shift: TTL–Compatible Input impedance: 50 kΩ Isolation: 2 kV

REMOTE INPUTS (IEC 61850 GSSE/GOOSE)

Input points: 32, configured from 64 incoming bit pairs Remote devices: 16 Default states on loss of comms.: On, Off, Latest/Off, Latest/On Remote DPS inputs: 5

2-22 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.4 SPECIFICATIONS

DIRECT INPUTS

Input points: 32 Remote devices: 16 Default states on loss of comms.: On, Off, Latest/Off, Latest/On Ring configuration: Yes, No Data rate: 64 or 128 kbps CRC: 32-bit CRC alarm:

Responding to: Rate of messages failing the CRC Monitoring message count: 10 to 10000 in steps of 1 Alarm threshold: 1 to 1000 in steps of 1

Unreturned message alarm:

Responding to: Rate of unreturned messages in the ring

configuration

Monitoring message count: 10 to 10000 in steps of 1 Alarm threshold: 1 to 1000 in steps of 1

LOW RANGE

Nominal DC voltage: 24 to 48 V Minimum DC voltage: 20 V Maximum DC voltage: 60 V for RL power supply module (obso-

lete), 75 V for SL power supply module

Voltage loss hold-up: 200 ms duration at maximum load NOTE: Low range is DC only.

HIGH RANGE

Nominal DC voltage: 125 to 250 V Minimum DC voltage: 88 V Maximum DC voltage: 300 V Nominal AC voltage: 100 to 240 V at 50/60 Hz Minimum AC voltage: 88 V at 25 to 100 Hz Maximum AC voltage: 265 V at 25 to 100 Hz Voltage loss hold-up: 200 ms duration at maximum load

TELEPROTECTION

Input points: 16 Remote devices: 3 Default states on loss of comms.: On, Off, Latest/Off, Latest/On Ring configuration: No Data rate: 64 or 128 kbps CRC: 32-bit

2.4.6 POWER SUPPLY

ALL RANGES

Volt withstand: 2 × Highest Nominal Voltage for 10 ms Power consumption: typical = 15 to 20 W/VA

maximum = 45 W/VA contact factory for exact order code consumption

INTERNAL FUSE

RATINGS

Low range power supply: 8 A / 250 V High range power supply: 4 A / 250 V

INTERRUPTING CAPACITY

AC: 100 000 A RMS symmetrical DC: 10 000 A

2.4.7 OUTPUTS

FORM-A RELAY

Make and carry for 0.2 s: 30 A as per ANSI C37.90 Carry continuous: 6 A Break (DC inductive, L/R = 40 ms):

VOLTAGE CURRENT

24 V 1 A

48 V 0.5 A 125 V 0.3 A 250 V 0.2 A

Operate time: < 4 ms Contact material: silver alloy

LATCHING RELAY

Make and carry for 0.2 s: 30 A as per ANSI C37.90 Carry continuous: 6 A as per IEEE C37.90 Break (DC resistive as per IEC61810-1):

VOLTAGE CURRENT

24 V 6 A

48 V 1.6 A 125 V 0.4 A 250 V 0.2 A

Operate time: < 4 ms Contact material: silver alloy Control: separate operate and reset inputs Control mode: operate-dominant or reset-dominant

FORM-A VOLTAGE MONITOR

Applicable voltage: approx. 15 to 250 V DC Trickle current: approx. 1 to 2.5 mA

FORM-A CURRENT MONITOR

Threshold current: approx. 80 to 100 mA

GE Multilin F35 Multiple Feeder Protection System 2-23

2.4 SPECIFICATIONS 2 PRODUCT DESCRIPTION

FORM-C AND CRITICAL FAILURE RELAY

Make and carry for 0.2 s: 30 A as per ANSI C37.90 Carry continuous: 8 A Break (DC inductive, L/R = 40 ms):

VOLTAGE CURRENT

24 V 1 A 48 V 0.5 A

125 V 0.3 A 250 V 0.2 A

Operate time: < 8 ms Contact material: silver alloy

FAST FORM-C RELAY

Make and carry: 0.1 A max. (resistive load) Minimum load impedance:

INPUT

VOLTAGE

250 V DC 20 KΩ 50 KΩ 120 V DC 5 KΩ 2 KΩ

48 V DC 2 KΩ 2 KΩ 24 V DC 2 KΩ 2 KΩ

Note: values for 24 V and 48 V are the same due to a required 95% voltage drop across the load impedance.

2 W RESISTOR 1 W RESISTOR

Operate time: < 0.6 ms Internal Limiting Resistor: 100 Ω, 2 W

IMPEDANCE

SOLID-STATE OUTPUT RELAY

Operate and release time: <100 μs Maximum voltage: 265 V DC Maximum continuous current: 5 A at 45°C; 4 A at 65°C Make and carry:

for 0.2 s: 30 A as per ANSI C37.90 for 0.03 s 300 A

Breaking capacity:

Operations/ interval

Break capability (0 to 250 V DC)

UL508 Utility

5000 ops /

1 s-On, 9 s-Off

1000 ops /

0.5 s-On, 0.5 s-Off

3.2 A

L/R = 10 ms

1.6 A

L/R = 20 ms

0.8 A

L/R = 40 ms

application

(autoreclose

scheme)

5ops/

0.2 s-On,

0.2 s-Off within 1

minute

10 A

L/R = 40 ms

Industrial

application

10000 ops /

0.2 s-On, 30 s-Off

10 A

L/R = 40 ms

CONTROL POWER EXTERNAL OUTPUT (FOR DRY CONTACT INPUT)

Capacity: 100 mA DC at 48 V DC Isolation: ±300 Vpk

REMOTE OUTPUTS (IEC 61850 GSSE/GOOSE)

Standard output points: 32 User output points: 32

DIRECT OUTPUTS

Output points: 32

DCMA OUTPUTS

Range: –1 to 1 mA, 0 to 1 mA, 4 to 20 mA Max. load resistance: 12 kΩ for –1 to 1 mA range

12 kΩ for 0 to 1 mA range 600 Ω for 4 to 20 mA range

Accuracy: ±0.75% of full-scale for 0 to 1 mA range

99% Settling time to a step change: 100 ms Isolation: 1.5 kV Driving signal: any FlexAnalog quantity Upper and lower limit for the driving signal: –90 to 90 pu in steps of

±0.5% of full-scale for –1 to 1 mA range ±0.75% of full-scale for 0 to 20 mA range

0.001

2-24 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.4 SPECIFICATIONS

NOTE

2.4.8 COMMUNICATION PROTOCOLS

RS232

Front port: 19.2 kbps, Modbus RTU

RS485

1 rear port: Up to 115 kbps, Modbus RTU, DNP 3,

Typical distance: 1200 m Isolation: 2 kV, isolated together at 36 Vpk

IEC 60870-5-103

FIBER ETHERNET PORT

PARAMETER FIBER TYPE

100 MB MULTI-

MODE

Wavelength 1310 nm Connector LC Transmit power –20 dBm Receiver sensitivity –30 dBm Power budget 10 dB Maximum input

power Typical distance 2 km Full duplex yes Redundancy yes

–14 dBm

ETHERNET (10/100 MB TWISTED PAIR)

Modes: 10 MB, 10/100 MB (auto-detect) Connector: RJ45

SIMPLE NETWORK TIME PROTOCOL (SNTP)

clock synchronization error: <10 ms (typical)

PRECISION TIME PROTOCOL (PTP)

PTP IEEE Std 1588 2008 (version 2) Power Profile (PP) per IEEE Standard PC37.238TM2011 Slave-only ordinary clock Peer delay measurement mechanism

PARALLEL REDUNDANCY PROTOCOL (PRP) (IEC 62439-3 CLAUSE 4, 2012)

Ethernet ports used: 2 and 3 Networks supported: 10/100 MB Ethernet

OTHER

TFTP, HTTP, IEC 60870-5-104, Ethernet Global Data (EGD)

SHIELDED TWISTED-PAIR INTERFACE OPTIONS

INTERFACE TYPE TYPICAL DISTANCE

RS422 1200 m G.703 100 m

RS422 distance is based on transmitter power and does not take into consideration the clock source provided by the user.

LINK POWER BUDGET

EMITTER, FIBER TYPE

820 nm LED, Multimode

1300 nm LED, Multimode

1300 nm ELED, Single mode

1300 nm Laser, Single mode

1550 nm Laser, Single mode

TRANSMIT

POWER

–20 dBm –30 dBm 10 dB

–21 dBm –30 dBm 9 dB

–23 dBm –32 dBm 9 dB

–1 dBm –30 dBm 29 dB

+5 dBm –30 dBm 35 dB

RECEIVED

SENSITIVITY

POWER

BUDGET

These power budgets are calculated from the manufacturer’s worst-case transmitter power and worst

2.4.9 INTER-RELAY COMMUNICATIONS

case receiver sensitivity.

The power budgets for the 1300 nm ELED are calculated from the manufacturer's transmitter power and receiver sensitivity at ambient temperature. At extreme temperatures these values deviate based on component tolerance. On average, the output power decreases as the temperature is increased by a factor 1dB / 5°C.

MAXIMUM OPTICAL INPUT POWER

EMITTER, FIBER TYPE MAX. OPTICAL

820 nm LED, Multimode –7.6 dBm 1300 nm LED, Multimode –11 dBm 1300 nm ELED, Single mode –14 dBm 1300 nm Laser, Single mode –14 dBm 1550 nm Laser, Single mode –14 dBm

INPUT POWER

GE Multilin F35 Multiple Feeder Protection System 2-25

2.4 SPECIFICATIONS 2 PRODUCT DESCRIPTION

NOTE

TYPICAL LINK DISTANCE

EMITTER TYPE CABLE

820 nm LED, multimode

1300 nm LED, multimode

1300 nm ELED, single mode

1300 nm Laser, single mode

1550 nm Laser, single mode

Typical distances listed are based on the following assumptions for system loss. As actual losses vary from one installation to another, the distance covered by your system may vary.

CONNECTOR LOSSES (TOTAL OF BOTH ENDS)

ST connector 2 dB

FIBER LOSSES

820 nm multimode 3 dB/km 1300 nm multimode 1 dB/km 1300 nm single mode 0.35 dB/km 1550 nm single mode 0.25 dB/km Splice losses: One splice every 2 km,

SYSTEM MARGIN

3 dB additional loss added to calculations to compensate for all other losses.

TYPE

62.5/125 μmST 1.65 km 50/125 μmST1.65 km

62.5/125 μmST 4 km 50/125 μmST 4 km 9/125 μmST11.4 km

9/125 μm ST 64 km

9/125 μm ST 105 km

at 0.05 dB loss per splice.

CONNECTOR

TYPE

TYPICAL

DISTANCE

Compensated difference in transmitting and receiving (channel asymmetry) channel delays using GPS satellite clock: 10 ms

AMBIENT TEMPERATURES

Storage temperature: –40 to 85°C Operating temperature: –40 to 60°C; the LCD contrast can be

impaired at temperatures less than – 20°C

HUMIDITY

Humidity: operating up to 95% (non-condensing) at

55°C (as per IEC60068-2-30 variant 1, 6 days).

2.4.10 ENVIRONMENTAL

OTHER

Altitude: 2000 m (maximum) Pollution degree: II Overvoltage category: II Ingress protection: IP20 front, IP10 back Noise: 0 dB

2-26 F35 Multiple Feeder Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.4 SPECIFICATIONS

2.4.11 TYPE TESTS

F35 TYPE TESTS

TEST REFERENCE STANDARD TEST LEVEL

Dielectric voltage withstand EN 60255-5 2.2 kV Impulse voltage withstand EN 60255-5 5 kV Damped oscillatory IEC 61000-4-18 / IEC 60255-22-1 2.5 kV CM, 1 kV DM Electrostatic discharge EN 61000-4-2 / IEC 60255-22-2 Level 3 RF immunity EN 61000-4-3 / IEC 60255-22-3 Level 3 Fast transient disturbance EN 61000-4-4 / IEC 60255-22-4 Class A and B Surge immunity EN 61000-4-5 / IEC 60255-22-5 Level 3 and 4 Conducted RF immunity EN 61000-4-6 / IEC 60255-22-6 Level 3 Power frequency immunity EN 61000-4-7 / IEC 60255-22-7 Class A and B Voltage interruption and ripple DC IEC 60255-11 12% ripple, 200 ms interrupts Radiated and conducted emissions CISPR11 / CISPR22 / IEC 60255-25 Class A Sinusoidal vibration IEC 60255-21-1 Class 1 Shock and bump IEC 60255-21-2 Class 1 Seismic IEC 60255-21-3 Class 1 Power magnetic immunity IEC 61000-4-8 Level 5 Pulse magnetic immunity IEC 61000-4-9 Level 4 Damped magnetic immunity IEC 61000-4-10 Level 4 Voltage dip and interruption IEC 61000-4-11 0, 40, 70, 80% dips; 250 / 300 cycle interrupts Damped oscillatory IEC 61000-4-12 2.5 kV CM, 1 kV DM Conducted RF immunity, 0 to 150 kHz IEC 61000-4-16 Level 4 Voltage ripple IEC 61000-4-17 15% ripple Ingress protection IEC 60529 IP40 front, IP10 back Cold IEC 60068-2-1 –40°C for 16 hours Hot IEC 60068-2-2 85°C for 16 hours Humidity IEC 60068-2-30 6 days, variant 1 Damped oscillatory IEEE/ANSI C37.90.1 2.5 kV, 1 MHz RF immunity IEEE/ANSI C37.90.2 20 V/m, 80 MHz to 1 GHz Safety UL 508 e83849 NKCR Safety UL C22.2-14 e83849 NKCR7 Safety UL 1053 e83849 NKCR Safety IEC 60255-27 Insulation: class 1, Pollution degree: 2, Over

voltage cat II

2.4.12 PRODUCTION TESTS

THERMAL

Products go through an environmental test based upon an

Accepted Quality Level (AQL) sampling process.

GE Multilin F35 Multiple Feeder Protection System 2-27

NOTICE

2.4 SPECIFICATIONS 2 PRODUCT DESCRIPTION

2.4.13 APPROVALS

APPROVALS

COMPLIANCE APPLICABLE COUNCIL

CE Low voltage directive EN 60255-5

C-UL-US --- UL 508

DIRECTIVE

EMC directive EN 60255-26 / EN 50263

ACCORDING TO

EN 61000-6-5

UL 1053 C22.2 No. 14

2.4.14 MAINTENANCE

MOUNTING

Attach mounting brackets using 20 inch-pounds (±2 inch-pounds) of torque.

CLEANING

Normally, cleaning is not required; but for situations where dust has accumulated on the faceplate display, a dry cloth can be used.

To avoid deterioration of electrolytic capacitors, power up units that are stored in a de-energized state once per year, for one hour continuously.

2-28 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.1 DESCRIPTION

17.56”

[446,02 mm]

9.687”

[246,05 mm]

11.016”

[279,81 mm]

7.460

[189,48 mm

6.960” [176,78 mm]

19.040”

[483,62 mm]

6.995”

[177,67 mm]

842807A1.CDR

3 HARDWARE 3.1DESCRIPTION 3.1.1 PANEL CUTOUT

a) HORIZONTAL UNITS

The F35 Multiple Feeder Protection System is available as a 19-inch rack horizontal mount unit with a removable faceplate. The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate contains additional user-programmable pushbuttons and LED indicators.

The modular design allows the relay to be easily upgraded or repaired by a qualified service person. The faceplate is hinged to allow easy access to the removable modules, and is itself removable to allow mounting on doors with limited rear depth.

The case dimensions are shown below, along with panel cutout details for panel mounting. When planning the location of your panel cutout, ensure that provision is made for the faceplate to swing open without interference to or from adjacent equipment.

The relay must be mounted such that the faceplate sits semi-flush with the panel or switchgear door, allowing the operator access to the keypad and the RS232 communications port. The relay is secured to the panel with the use of four screws supplied with the relay.

Figure 3–1: F35 HORIZONTAL DIMENSIONS (ENHANCED PANEL)

GE Multilin F35 Multiple Feeder Protection System 3-1

3.1 DESCRIPTION 3 HARDWARE

18.370”

[466,60 mm]

842808A1.CDR

0.280” [7,11 mm] Typ. x 4

4.000”

[101,60 mm]

17.750”

[450,85 mm]

CUT-OUT

19.00”

(482.6 mm)

7.00” (177.8 mm)

Horizontal front view

Horizontal top view (19”, 4 RU)

17.52”

(445.0 mm)

Brackets repositioned for switchgear mounting

10.90” (276.8 mm)

9.80”

(248.9 mm)

8.97”

(227.8 mm)

17.75”

(450.8 mm)

7.13”

(181.1 mm)

Cutout

18.37”

(466.6 mm)

4.00” (101.6 mm)

1.57” (39.8 mm)

4 × 0.28” (7.1 mm) diameter

17.72”

(450.1 mm)

14.52”

(368.8 mm)

9.52”

(241.8 mm)

8 × 0.156 Ø

5.00”

(127.0 mm)

0.375”

(9.5 mm)

0.375” (9.5 mm)

Remote mounting, view from the rear of the panel

Bezel

outline

0.375” (9.5)

1.875”

(47.6)

0.375” (9.5)

4.875” (121.5 mm)

6.96” (176.8 mm)

827704B4.CDR

Figure 3–2: F35 HORIZONTAL MOUNTING (ENHANCED PANEL)

Figure 3–3: F35 HORIZONTAL MOUNTING AND DIMENSIONS (STANDARD PANEL)

b) VERTICAL UNITS

The F35 Multiple Feeder Protection System is available as a reduced size (¾) vertical mount unit, with a removable faceplate. The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate contains additional user-programmable pushbuttons and LED indicators.

3-2 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.1 DESCRIPTION

7.48”

(190.0 mm)

15.00” (381.0 mm)

13.56” (344.4 mm)

1.38” (35.2 mm)

9.58”

(243.4 mm)

7.00”

(177.7 mm)

4.00”

(101.6 mm)

7.10”

(180.2 mm)

13.66” (347.0 mm)

14.03” (356.2 mm)

0.20” (5.1 mm)

1.55” (39.3 mm)

4 Places

0.213” (5.41 mm)

Front of Panel

Mounting Bracket

Vertical Enhanced Front View

Vertical Enhanced Top View

Vertical Enhanced Mounting Panel

CUTOUT

Front of Panel Reference only

Terminal Blocks

Front Bezel

Front of Panel

Mounting Bracket

Vertical Enhanced Side View

843809A2.cdr

Figure 3–4: F35 VERTICAL DIMENSIONS (ENHANCED PANEL)

GE Multilin F35 Multiple Feeder Protection System 3-3

13.72"

(348.5 mm)

7.00"

(177.8 mm)

13.50"

(342.9 mm)

Front of

panel

Front bezel

Panel

Mounting bracket

1.57”

(39.9 mm)

4.00

(101.6)

7.13”

(181.1 mm)

0.46” (11.7 mm)

13.65” (346.7 mm)

14.40” (365.8 mm)

0.213" (5.4 mm), 4 places

Vertical front view

Vertical side view

843755A4.CDR

Vertical panel mounting

1.85"

(47.0 mm)

9.00"

(228.6 mm)

7.00"

(177.8 mm)

Terminal blocks

Mounting bracket

Panel shown for reference only

Vertical bottom view

3.1 DESCRIPTION 3 HARDWARE

Figure 3–5: F35 VERTICAL MOUNTING AND DIMENSIONS (STANDARD PANEL)

For side mounting F35 devices with the enhanced front panel, see the following documents available on the UR DVD and the GE Grid Solutions website:

• GEK-113180: UR-Series UR-V Side-Mounting Front Panel Assembly Instructions

• GEK-113181: Connecting a Remote UR-V Enhanced Front Panel to a Vertical UR Device Instruction Sheet

• GEK-113182: Connecting a Remote UR-V Enhanced Front Panel to a Vertically-Mounted Horizontal UR Device Instruction Sheet

For side mounting F35 devices with the standard front panel, use the following figures.

3-4 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.1 DESCRIPTION

Figure 3–6: F35 VERTICAL SIDE MOUNTING INSTALLATION (STANDARD PANEL)

GE Multilin F35 Multiple Feeder Protection System 3-5

CUT-OUT

1.33" (33.9)

2.83"

(71.9)

6.66"

(169.2)

12.20"

(309.9)

0.159" DIA. (6 PLACES) (4.0)

0.213" DIA. (5.4) (4 PLACES) SEE HOLES MARKED 'X'

INCHES

MILLIMETERS

5.33"

(135.4)

PANEL SHOWN FOR REFERENCE ONLY (VIEWED FROM FRONT)

'X' 'X'

1.00" (25.4)

1.00"

(25.4)

10.05 (255.3)

0.04 (1.0)

0.68" (17.3)

5.27

(133.8)

843753A3.cdr

3.1 DESCRIPTION 3 HARDWARE

Figure 3–7: F35 VERTICAL SIDE MOUNTING REAR DIMENSIONS (STANDARD PANEL)

3-6 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.1 DESCRIPTION

XWV U T S PNM L KJ H DGF BR

abc abc abc abc

Optional

direct

input/output

module

CPU module

(T module shown)

Optional

contact

input/output

module

CT/VT

module

Power supply

module

Tx1

Tx2

Rx1

Rx2

Tx1

Tx2

832781A3.CDR

Optional

CT/VT or

contact

input/output

module

Optional

contact

input/output

module

ACT3

LK3

ACT2

LK2

ACT1

LK1

Model: Mods: Wiring Diagram: Inst. Manual: Serial Number: Firmware: Mfg. Date: PO Num: Item Num:

F35D00HCHF8AH6AM6BP8BX7A NONE See manual 1601-0106 AAIC07000515 A09MA521.000 NOV 12, 2012

600001234.56

Control Power: Contact Inputs: Contact Outputs:

125-250 V — 0.7A/100-240, 50/60Hz, 0.7A 300 V ---- Max 10mA Refer to Instruction Manual

RATINGS:

F35

Multiple Feeder Management Relay

GE Multilin

LISTED

52TL

IND.CONT. EQ.

E83849

WARNING

NOTICE

3.1.2 REAR TERMINAL LAYOUT

The relay follows a convention with respect to terminal number assignments which are three characters long assigned in order by module slot position, row number, and column letter. Two-slot wide modules take their slot designation from the first slot position (nearest to CPU module) which is indicated by an arrow marker on the terminal block. See the following figure for an example of rear terminal assignments.

Figure 3–8: REAR TERMINAL VIEW

Do not touch any rear terminals while the relay is energized.

The small form-factor pluggable ports (SFPs) are pluggable transceivers. Do not use non-validated transceivers or install validated transceivers in the wrong Ethernet slot, else damage can occur.

Figure 3–9: EXAMPLE OF MODULES IN F AND H SLOTS

GE Multilin F35 Multiple Feeder Protection System 3-7

3.2 WIRING 3 HARDWARE

AC or DC

( DC only )

F35

Multiple Feeder Protection System

Wet

Ground bus

No. 10AWG

minimum

Modules must be

grounded if terminal

is provided

832778A2.CDR

Dry

Critical failure

48 V DC output

Control power

Power supply

Filter

Surge

B3a

B1b

B8a

B6b

B8b

B6a

B3b

B1a B2b

B5b

P6a

P8a

P5b

P7b

P8b

P5a

P7a

P6c

P8c

P5c

P7c

P1a

P2b

P1c

P1b

P2c

P2a

P4a

P4c

P3b

P3a

P4b

P3c

Contact input/output modules

Contact input P5a

Contact input P7a

Contact input P5c

Contact input P7c

Contact input P6a

Contact input P8a

Contact input P6c

Contact input P8c

Common P5b

Common P7b

Surge

H5c

H8a

H7b

H8b

H5a

H7a

H8c

H5b

H7c

H1a

H2b

H1c

H1b

H2c

H2a

H4a

H4c

H3b

H3a

H4b

H3c

Contact input/output modules

Contact input H7a Contact input H7c Contact input H8a Contact input H8c Common H7b

Surge

H6c

H6a H6b

Fibre optic

Ground at

remote

device

Shielded

twisted pairs

Co-axial cable

COM

100BaseFX

D1a D2a

D4b

D3a

D4a

IRIG-B input

RS485 COM 2

Port 2

Port 1

CPU T

Tx2

Rx2

Tx1

Rx1

BNC

Typical configuration. The AC signal path is configurable.

Contacts shown

with no

control power

TC1

Voltage supervision

Voltage and

current supervision

TC2

F4c

F4a F4b

F3c

F1c

F2b

F2a

F2c

F1a F1b

F3a F3b

Current inputs

Type 8H/8J CT/VT module

IA5

IG5

IC5

IB5

IA1

IG1

IC1

IB1

F8c

F8a F8b

F7c

F5c

F6b

F6a

F6c

F5a F5b

F7a F7b

IA5

IG5

IC5

IB5

IA1

IG1

IC1

IB1

M4c

M4a M4b

M3c

M1c

M2b

M2a

M2c

M1a M1b

M3a M3b

Current inputs

Type 8H/8J CT/VT module

IA5

IG5

IC5

IB5

IA1

IG1

IC1

IB1

M8c

M8a M8b

M7c

M5c

M6b

M6a

M6c

M5a M5b

M7a M7b

IA5

IG5

IC5

IB5

IA1

IG1

IC1

IB1

U4c

U4a U4b

U3c

U1c

U2b

U2a

U2c

U1a U1b

U3a U3b

Current inputs

Type 8F/8G CT/VT module

IA5

IG5

IC5

IB5

IA1

IG1

IC1

IB1

Positive watts

U7c

U7a

U5a

U6c

U5c U6a

U8c

U8a

VX VX

Voltage inputs

Connection as required

100BaseFX

Tx3

Rx3

100BaseFX

Port 3

3.2WIRING 3.2.1 TYPICAL WIRING

Figure 3–10: TYPICAL WIRING DIAGRAM (T MODULE SHOWN FOR CPU)

3-8 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.2 WIRING

NOTICE

3.2.2 DIELECTRIC STRENGTH

The dielectric strength of the UR-series module hardware is shown in the following table:

Table 3–1: DIELECTRIC STRENGTH OF UR-SERIES MODULE HARDWARE

MODULE

TYPE

1 Power supply High (+); Low (+); (–) Chassis 2000 V AC for 1 minute 1 Power supply 48 V DC (+) and (–) Chassis 2000 V AC for 1 minute 1 Power supply Relay terminals Chassis 2000 V AC for 1 minute 2 Reserved N/A N/A N/A 3 Reserved N/A N/A N/A 4 Digital contact inputs/

5 Analog inputs/outputs All except 8b Chassis < 50 V DC 6 Digital contact inputs/

8 CT/VT All Chassis 2000 V AC for 1 minute 9 CPU All Chassis 2000 V AC for 1 minute

MODULE FUNCTION TERMINALS DIELECTRIC STRENGTH

FROM TO

outputs

G.703 All except 2b, 3a, 7b, 8a Chassis 2000 V AC for 1 minute

RS422 All except 6a, 7b, 8a Chassis < 50 V DC

Filter networks and transient protection clamps are used in the hardware to prevent damage caused by high peak voltage transients, radio frequency interference (RFI), and electromagnetic interference (EMI). These protective components can be damaged by application of the ANSI/IEEE C37.90 specified test voltage for a period longer than the specified one minute.

All Chassis 2000 V AC for 1 minute

(AC)

3.2.3 CONTROL POWER

Control power supplied to the relay must be connected to the matching power supply range of the relay. If voltage is applied to the wrong terminals, damage can occur.

The F35 relay, like almost all electronic relays, contains electrolytic capacitors. These capacitors are well-known to deteriorate over time if voltage is not applied periodically. Deterioration can be avoided by powering up the relay at least once a year.

The power supply module can be ordered for two possible voltage ranges, and the UR can be ordered with or without a redundant power supply module option. Each range has a dedicated input connection for proper operation. The ranges are as shown below (see the Specifications section of chapter 2 for details):

• Low (LO) range: 24 to 48 V (DC only) nominal.

• High (HI) range: 125 to 250 V nominal. The power supply module provides power to the relay and supplies power for dry contact input connections. The power supply module provides 48 V DC power for dry contact input connections and a critical failure relay (see the

Typical wiring diagram earlier). The critical failure relay is a form-C device that is energized once control power is applied and the relay has successfully booted up with no critical self-test failures. If on-going self-test diagnostic checks detect a critical failure (see the Self-test Errors section in chapter 7) or control power is lost, the relay is de-energize.

For high reliability systems, the F35 has a redundant option in which two F35 power supplies are placed in parallel on the bus. If one of the power supplies become faulted, the second power supply assumes the full load of the relay without any interruptions. Each power supply has a green LED on the front of the module to indicate it is functional. The critical fail relay of the module also indicates a faulted power supply.

GE Multilin F35 Multiple Feeder Protection System 3-9

3.2 WIRING 3 HARDWARE

AC or DC

NOTE: 14 gauge stranded wire with suitable disconnect devices is recommended.

Heavy copper conductor

or braided wire

Switchgear

ground bus

UR-series

protection system

FILTER

SURGE

–

LOW

HIGH

B8b B8a B6a B6b B5b

CONTROL

POWER

827247A1.CDR

NOTICE

An LED on the front of the control power module shows the status of the power supply:

LED INDICATION POWER SUPPLY

CONTINUOUS ON OK ON / OFF CYCLING Failure OFF Failure

Figure 3–11: CONTROL POWER CONNECTION

3.2.4 CT/VT MODULES

A CT/VT module can have voltage or current inputs on channels 1 through 4 inclusive, or channels 5 through 8 inclusive. Channels 1 and 5 are intended for connection to phase A, and are labeled as such in the relay. Likewise, channels 2 and 6 are intended for connection to phase B, and channels 3 and 7 are intended for connection to phase C.

Channels 4 and 8 are intended for connection to a single-phase source. For voltage inputs, these channel are labelled as auxiliary voltage (VX). For current inputs, these channels are intended for connection to a CT between system neutral and ground, and are labelled as ground current (IG).

Verify that the connection made to the relay terminals for nominal current of 1 A or 5 A matches the secondary rating of the connected CTs. Unmatched CTs can result in equipment damage or inade-

quate protection. To connect the module, size 12 American Wire Gauge (AWG) is commonly used; the maximum size is 10 AWG. CT/VT modules can be ordered with a standard ground current input that is the same as the phase current input. Each AC

current input has an isolating transformer and an automatic shorting mechanism that shorts the input when the module is withdrawn from the chassis. There are no internal ground connections on the current inputs. Current transformers with 1 to 50000 A primaries and 1 A or 5 A secondaries can be used.

CT/VT modules with a sensitive ground input are also available. The ground CT input of the sensitive ground modules is 10 times more sensitive than the ground CT input of standard CT/VT modules. However, the phase CT inputs and phase VT inputs are the same as those of regular CT/VT modules.

The above modules have enhanced diagnostics that can automatically detect CT/VT hardware failure and take the relay out of service.

CT connections for both ABC and ACB phase rotations are identical as shown in the Typical wiring diagram. The exact placement of a zero-sequence core balance CT to detect ground fault current is shown as follows. Twisted-pair

cabling on the zero-sequence CT is recommended.

3-10 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.2 WIRING

Ground connection to neutral must be on the source side

UNSHIELDED CABLE

LOAD

ABCN G

Ground outside CT

Source

LOAD

SHIELDED CABLE

996630A6.CDR

ABC

Source

To ground; must be on load side

Stress cone

shields

Current inputs

8F, 8G, 8L, and 8M modules (4 CTs and 4 VTs)

Voltage inputs

IA5

IC5

IB5

IG5

IA1

IC1

IB1

IG1

Current inputs

842766A3.CDR

IA5

IC5

IB5

IG5

IA1

IC1

IB1

IG1

8H, 8J, 8N, and 8R modules (8 CTs)

Figure 3–12: ZERO-SEQUENCE CORE BALANCE CT INSTALLATION

The phase voltage channels are used for most metering and protection purposes. The auxiliary voltage channel is used as input for the synchrocheck and volts-per-hertz features.

Substitute the tilde “~” symbol with the slot position of the module in the following figure.

Figure 3–13: CT/VT MODULE WIRING

GE Multilin F35 Multiple Feeder Protection System 3-11

3.2 WIRING 3 HARDWARE

3.2.5 PROCESS BUS MODULES

The F35 can be ordered with a process bus interface module. This module is designed to interface with the GE Multilin HardFiber system, allowing bidirectional IEC 61850 fiber optic communications with up to eight HardFiber merging units, known as Bricks. The HardFiber system has been designed to integrate seamlessly with the existing UR-series applications, including protection functions, FlexLogic, metering, and communications.

The IEC 61850 process bus system offers the following benefits:

• Reduces labor associated with design, installation, and testing of protection and control applications using the F35 by

reducing the number of individual copper terminations

• Integrates seamlessly with existing F35 applications, since the IEC 61850 process bus interface module replaces the

traditional CT/VT modules

• Communicates using open standard IEC 61850 messaging

For additional details on the HardFiber system, see GE publication GEK-113658: HardFiber Process Bus System Instruction Manual.

3.2.6 CONTACT INPUTS AND OUTPUTS

Every contact input/output module has 24 terminal connections. They are arranged as three terminals per row, with eight rows in total. A given row of three terminals can be used for the outputs of one relay. For example, for form-C relay outputs, the terminals connect to the normally open (NO), normally closed (NC), and common contacts of the relay. For a form-A output, there are options of using current or voltage detection for feature supervision, depending on the module ordered. The terminal configuration for contact inputs is different for the two applications.

The contact inputs are grouped with a common return. The input/output modules have two versions of grouping: four inputs per common return and two inputs per common return. When a contact input/output module is ordered, four inputs per common is used. If the inputs must be isolated per row, then two inputs per common return should be selected (4D module).

The tables and diagrams on the following pages illustrate the module types (6A, etc.) and contact arrangements that can be ordered for the relay. Since an entire row is used for a single contact output, the name is assigned using the module slot position and row number. However, since there are two contact inputs per row, these names are assigned by module slot position, row number, and column position.

Some form-A / solid-state relay outputs include circuits to monitor the DC voltage across the output contact when it is open, and the DC current through the output contact when it is closed. Each of the monitors contains a level detector whose output is set to logic “On” when the current in the circuit is above the threshold setting. The voltage monitor is set to “On” when there is a voltage across open contact (the detector allows a current of about 1 to 2.5 mA), and the current monitor is set to “On” when the current flowing through the closed contact exceeds about 80 to 100 mA. The voltage monitor is intended to check the health of the overall trip circuit, and the current monitor can be used to seal-in the output contact until an external contact has interrupted current flow. If enabled, the current monitoring can be used as a seal-in signal to ensure that the form-A contact does not attempt to break the energized inductive coil circuit and weld the output contacts.

Block diagrams are shown as follows for form-A and solid-state relay outputs with optional voltage monitor, optional current monitor, and with no monitoring. The actual values shown for contact output 1 are the same for all contact outputs. Form-A contact output with or without a current or voltage monitoring option is not polarity sensitive. The polarity shown in the figure is required for solid-state contact output connection.

3-12 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.2 WIRING

Load

~#a

~#b

~#c

827862A4.CDR

a) Voltage with optional current monitoring

Voltage monitoring only

Load

Both voltage and current monitoring

Load

b) Current with optional voltage monitoring

Current monitoring only Both voltage and current monitoring

(external jumper a-b is required)

Load

c) No monitoring

~#a

~#b

~#c

~#a

~#b

~#c

~#a

~#b

~#c

~#a

~#b

~#c

WARNING

NOTE

NOTICE

Figure 3–14: FORM-A AND SOLID-STATE CONTACT OUTPUTS WITH VOLTAGE AND CURRENT MONITORING

The operation of voltage and current monitors is reflected with the corresponding FlexLogic operands (CONT OP # VON,

CONT OP # VOFF, and CONT OP # ION) which can be used in protection, control, and alarm logic. The typical application of

the voltage monitor is breaker trip circuit integrity monitoring; a typical application of the current monitor is seal-in of the control command.

See the Digital Elements section of chapter 5 for an example of how form-A and solid-state relay contacts can be applied for breaker trip circuit integrity monitoring.

Consider relay contacts unsafe to touch when the unit is energized.

USE OF FORM-A AND SOLID-STATE RELAY OUTPUTS IN HIGH IMPEDANCE CIRCUITS

For form-A and solid-state relay output contacts internally equipped with a voltage measuring circuit across the contact, the circuit has an impedance that can cause a problem when used in conjunction with external high input impedance monitoring equipment such as modern relay test set trigger circuits. These monitoring circuits may continue to read the form-A contact as being closed after it has closed and subsequently opened, when measured as an impedance.

The solution is to use the voltage measuring trigger input of the relay test set, and connect the form-A contact through a voltage-dropping resistor to a DC voltage source. If the 48 V DC output of the power supply is used as a source, a 500 Ω, 10 W resistor is appropriate. In this configuration, the voltage across either the form-A contact or the resistor can be used to monitor the state of the output.

Wherever a tilde “~” symbol appears, substitute with the slot position of the module; wherever a number sign “#” appears, substitute the contact number

When current monitoring is used to seal-in the form-A and solid-state relay contact outputs, the FlexLogic operand driving the contact output should be given a reset delay of 10 ms to prevent damage of the output contact (in situations when the element initiating the contact output is bouncing, at values in the region of the pickup value).

GE Multilin F35 Multiple Feeder Protection System 3-13

3.2 WIRING 3 HARDWARE

Table 3–2: CONTACT INPUT AND OUTPUT MODULE ASSIGNMENTS

~6A MODULE ~6B MODULE ~6C MODULE ~6D MODULE

TERMINAL

ASSIGNMENT

~1 Form-A ~1 Form-A ~1 Form-C ~1a, ~1c 2 Inputs ~2 Form-A ~2 Form-A ~2 Form-C ~2a, ~2c 2 Inputs ~3 Form-C ~3 Form-C ~3 Form-C ~3a, ~3c 2 Inputs

~4 Form-C ~4 Form-C ~4 Form-C ~4a, ~4c 2 Inputs ~5a, ~5c 2 Inputs ~5 Form-C ~5 Form-C ~5a, ~5c 2 Inputs ~6a, ~6c 2 Inputs ~6 Form-C ~6 Form-C ~6a, ~6c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7 Form-C ~7a, ~7c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8 Form-C ~8a, ~8c 2 Inputs

OUTPUT OR

INPUT

TER MINA L

ASSIGNMENT

OUTPUT OR

INPUT

~6E MODULE ~6F MODULE ~6G MODULE ~6H MODULE

TERMINAL

ASSIGNMENT

~1Form-C ~1 Fast Form-C ~1Form-A ~1Form-A

~2Form-C ~2 Fast Form-C ~2Form-A ~2Form-A

~3Form-C ~3 Fast Form-C ~3Form-A ~3Form-A

~4Form-C ~4 Fast Form-C ~4Form-A ~4Form-A ~5a, ~5c 2 Inputs ~5 Fast Form-C ~5a, ~5c 2 Inputs ~5 Form-A ~6a, ~6c 2 Inputs ~6 Fast Form-C ~6a, ~6c 2 Inputs ~6 Form-A ~7a, ~7c 2 Inputs ~7 Fast Form-C ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~8a, ~8c 2 Inputs ~8 Fast Form-C ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs

OUTPUT OR

INPUT

TER MINA L

ASSIGNMENT

OUTPUT TERMINAL

TERMINAL

ASSIGNMENT

OUTPUT TERMINAL

OUTPUT OR

INPUT

ASSIGNMENT

TER MINA L

ASSIGNMENT

OUTPUT

OUTPUT OR

INPUT

~6K MODULE ~6L MODULE ~6M MODULE ~6N MODULE

TERMINAL

ASSIGNMENT

~1 Form-C ~1Form-A ~1Form-A ~1Form-A

~2 Form-C ~2Form-A ~2Form-A ~2Form-A

~3 Form-C ~3Form-C ~3Form-C ~3Form-A

~4 Form-C ~4Form-C ~4Form-C ~4Form-A

~5 Fast Form-C ~5a, ~5c 2 Inputs ~5Form-C ~5a, ~5c 2 Inputs

~6 Fast Form-C ~6a, ~6c 2 Inputs ~6Form-C ~6a, ~6c 2 Inputs

~7 Fast Form-C ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs

~8 Fast Form-C ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs

~6P MODULE ~6R MODULE ~6S MODULE ~6T MODULE

TERMINAL

ASSIGNMENT

~1 Form-A ~1Form-A ~1Form-A ~1Form-A

~2 Form-A ~2Form-A ~2Form-A ~2Form-A

~3 Form-A ~3Form-C ~3Form-C ~3Form-A

~4 Form-A ~4Form-C ~4Form-C ~4Form-A

~5 Form-A ~5a, ~5c 2 Inputs ~5Form-C ~5a, ~5c 2 Inputs

~6 Form-A ~6a, ~6c 2 Inputs ~6Form-C ~6a, ~6c 2 Inputs

~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs

OUTPUT TERMINAL

OUTPUT OR

INPUT

ASSIGNMENT

TER MINA L

ASSIGNMENT

OUTPUT OR

INPUT

OUTPUT OR

INPUT

TERMINAL

ASSIGNMENT

TERMINAL

ASSIGNMENT

OUTPUT OR

INPUT

OUTPUT OR

INPUT

TER MINA L

ASSIGNMENT

TER MINA L

ASSIGNMENT

OUTPUT OR

INPUT

OUTPUT OR

INPUT

3-14 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.2 WIRING

~6U MODULE ~6V MODULE ~67 MODULE ~4A MODULE

TERMINAL

ASSIGNMENT

~1 Form-A ~1 Form-A ~1Form-A ~1Not Used ~2 Form-A ~2 Form-A ~2Form-A ~2 Solid-State ~3 Form-A ~3 Form-C ~3Form-A ~3Not Used ~4 Form-A ~4 2 Outputs ~4Form-A ~4 Solid-State ~5 Form-A ~5a, ~5c 2 Inputs ~5Form-A ~5Not Used ~6 Form-A ~6a, ~6c 2 Inputs ~6Form-A ~6 Solid-State

~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7Form-A ~7Not Used ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8Form-A ~8 Solid-State

TERMINAL

ASSIGNMENT

~1Not Used ~1 Not Used ~1a, ~1c 2 Inputs ~1 2 Outputs ~2 Solid-State ~2 Solid-State ~2a, ~2c 2 Inputs ~2 2 Outputs ~3Not Used ~3 Not Used ~3a, ~3c 2 Inputs ~3 2 Outputs ~4 Solid-State ~4 Solid-State ~4a, ~4c 2 Inputs ~4 2 Outputs ~5Not Used ~5 Not Used ~5a, ~5c 2 Inputs ~5 2 Outputs ~6 Solid-State ~6 Solid-State ~6a, ~6c 2 Inputs ~6 2 Outputs ~7Not Used ~7 Not Used ~7a, ~7c 2 Inputs ~72 Outputs ~8 Solid-State ~8 Solid-State ~8a, ~8c 2 Inputs ~8Not Used

OUTPUT OR

INPUT

~4B MODULE ~4C MODULE ~4D MODULE ~4L MODULE

OUTPUT TERMINAL

TER MINA L

ASSIGNMENT

OUTPUT OR

INPUT

OUTPUT TERMINAL

TERMINAL

ASSIGNMENT

OUTPUT TERMINAL

ASSIGNMENT

OUTPUT

GE Multilin F35 Multiple Feeder Protection System 3-15

842762A3.CDR

3.2 WIRING 3 HARDWARE

Figure 3–15: CONTACT INPUT AND OUTPUT MODULE WIRING (1 of 2)

3-16 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.2 WIRING

DIGITAL I/O

CONTACT IN 7a

CONTACT IN 7c

CONTACT IN 8a

CONTACT IN 8c

COMMON 7b

SURGE

DIGITAL I/O

CONTACT IN 7a CONTACT IN 7c CONTACT IN 8a CONTACT IN 8c

COMMON 7b

SURGE

DIGITAL I/O

CONTACT IN 7a CONTACT IN 7c CONTACT IN 8a CONTACT IN 8c

COMMON 7b

SURGE

DIGITAL I/O

CONTACT IN 7a CONTACT IN 7c CONTACT IN 8a CONTACT IN 8c

COMMON 7b

SURGE

DIGITAL I/O

CONTACT IN 7a

CONTACT IN 5a

CONTACT IN 7c

CONTACT IN 5c

CONTACT IN 8a

CONTACT IN 6a

CONTACT IN 8c

CONTACT IN 6c

COMMON 7b

COMMON 5b

SURGE

DIGITAL I/O

CONTACT IN 7a

CONTACT IN 5a

CONTACT IN 7c

CONTACT IN 5c

CONTACT IN 8a

CONTACT IN 6a

CONTACT IN 8c

CONTACT IN 6c

COMMON 7b

COMMON 5b

SURGE

DIGITAL I/O

CONTACT IN 7a

CONTACT IN 5a

CONTACT IN 7c

CONTACT IN 5c

CONTACT IN 8a

CONTACT IN 6a

CONTACT IN 8c

CONTACT IN 6c

COMMON 7b

COMMON 5b

SURGE

DIGITAL I/O

CONTACT IN 7a

CONTACT IN 5a

CONTACT IN 7c

CONTACT IN 5c

CONTACT IN 8a

CONTACT IN 6a

CONTACT IN 8c

CONTACT IN 6c

COMMON 7b

COMMON 5b

SURGE

842763A2.CDR

DIGITAL I/O

CONTACT IN 7a

CONTACT IN 5a

CONTACT IN 7c

CONTACT IN 5c

CONTACT IN 8a

CONTACT IN 6a

CONTACT IN 8c

CONTACT IN 6c

COMMON 7b

COMMON 5b

SURGE

NOTICE

GE Multilin F35 Multiple Feeder Protection System 3-17

Figure 3–16: CONTACT INPUT AND OUTPUT MODULE WIRING (2 of 2)

For proper functionality, observe the polarity shown in the figures for all contact input and output connections.

3.2 WIRING 3 HARDWARE

827741A5.CDR

24 to 250 V

(Wet) (Dry)

Contact input 1 Contact input 2 Contact input 3

Surge

Contact input 4

~7a

Common

~7b

~7c ~8a

~8b

~8c

Contact input 1 Contact input 2 Contact input 3

Surge

Contact input 4

~7a

Common

~7b

~7c ~8a

~8b

~8c

Control power

Surge

B5b

Filter

B8b

B6b B6a B8a

Critical failure

B1b

48 V DC output

B3b

B1a B2b B3a

HI+ LO+

Power supply module

Terminals from type 6B contact input/output module

NOTE

CONTACT INPUTS

A dry contact has one side connected to terminal B3b. This is the positive 48 V DC voltage rail supplied by the power supply module. The other side of the dry contact is connected to the required contact input terminal. Each contact input group has its own common (negative) terminal which must be connected to the DC negative terminal (B3a) of the power supply module. When a dry contact closes, a current of 1 to 3 mA flows through the associated circuit.

A wet contact has one side connected to the positive terminal of an external DC power supply. The other side of this contact is connected to the required contact input terminal. If a wet contact is used, then the negative side of the external source must be connected to the relay common (negative) terminal of each contact group. The maximum external source voltage for this arrangement is 300 V DC.

The voltage threshold at which each group of four contact inputs detects a closed contact input is programmable as 17 V DC for 24 V sources, 33 V DC for 48 V sources, 84 V DC for 110 to 125 V sources, and 166 V DC for 250 V sources.

Figure 3–17: DRY AND WET CONTACT INPUT CONNECTIONS

Wherever a tilde “~” symbol appears, substitute with the slot position of the module.

There is no provision in the relay to detect a DC ground fault on 48 V DC control power external output. We recommend using an external DC supply.

3-18 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.2 WIRING

842749A1.CDR

50 to 70 mA

3 mA

25 to 50 ms

current

time

CONTACT INPUT 1 AUTO-BURNISH = OFF

= OFFCONTACT INPUT 2 AUTO-BURNISH

CONTACT INPUT 1 AUTO-BURNISH CONTACT INPUT 2 AUTO-BURNISH

= ON = OFF

CONTACT INPUT 1 AUTO-BURNISH CONTACT INPUT 2 AUTO-BURNISH

= OFF = ON

CONTACT INPUT 1 AUTO-BURNISH CONTACT INPUT 2 AUTO-BURNISH

= ON = ON

842751A1.CDR

USE OF CONTACT INPUTS WITH AUTO-BURNISHING

The contact inputs sense a change of the state of the external device contact based on the measured current. When external devices are located in a harsh industrial environment (either outdoor or indoor), their contacts can be exposed to various types of contamination. Normally, there is a thin film of insulating sulfidation, oxidation, or contaminates on the surface of the contacts, sometimes making it difficult or impossible to detect a change of the state. This film must be removed to establish circuit continuity – an impulse of higher than normal current can accomplish this.

The contact inputs with auto-burnish create a high current impulse when the threshold is reached to burn off this oxidation layer as a maintenance to the contacts. Afterwards the contact input current is reduced to a steady-state current. The impulse has a 5 second delay after a contact input changes state.

Figure 3–18: CURRENT THROUGH CONTACT INPUTS WITH AUTO-BURNISHING

Regular contact inputs limit current to less than 3 mA to reduce station battery burden. In contrast, contact inputs with autoburnishing allow currents up to 50 to 70 mA at the first instance when the change of state was sensed. Then, within 25 to 50 ms, this current is slowly reduced to 3 mA as indicated above. The 50 to 70 mA peak current burns any film on the contacts, allowing for proper sensing of state changes. If the external device contact is bouncing, the auto-burnishing starts when external device contact bouncing is over.

Another important difference between the auto-burnishing input module and the regular input modules is that only two contact inputs have common ground, as opposed to four contact inputs sharing one common ground (refer to the Contact Input and Output Module Wiring diagrams). This is beneficial when connecting contact inputs to separate voltage sources. Consequently, the threshold voltage setting is also defined per group of two contact inputs.

The auto-burnish feature can be disabled or enabled using the DIP switches found on each daughter card. There is a DIP switch for each contact, for a total of 16 inputs.

Figure 3–19: AUTO-BURNISH DIP SWITCHES

GE Multilin F35 Multiple Feeder Protection System 3-19

3.2 WIRING 3 HARDWARE

NOTE

842764A1.CDR

The auto-burnish circuitry has an internal fuse for safety purposes. During regular maintenance, check the autoburnish functionality using an oscilloscope.

3.2.7 TRANSDUCER INPUTS/OUTPUTS

Transducer input modules can receive input signals from external DCmA output transducers (DCmA In) or resistance temperature detectors (RTDs). Hardware and software are provided to receive signals from these external transducers and convert these signals into a digital format for use as required.

Transducer output modules provide DC current outputs in several standard DCmA ranges. Software is provided to configure virtually any analog quantity used in the relay to drive the analog outputs.

Every transducer input/output module has a total of 24 terminal connections. These connections are arranged as three terminals per row with a total of eight rows. A given row can be used for either inputs or outputs, with terminals in column "a" having positive polarity and terminals in column "c" having negative polarity. Since an entire row is used for a single input/

output channel, the name of the channel is assigned using the module slot position and row number. Each module also requires that a connection from an external ground bus be made to terminal 8b. The current outputs

require a twisted-pair shielded cable, where the shield is grounded at one end only. The following figure illustrates the transducer module types (5A, 5C, 5D, 5E, and 5F) and channel arrangements that can be ordered for the relay.

Wherever a tilde “~” symbol appears, substitute with the slot position of the module.

Figure 3–20: TRANSDUCER INPUT/OUTPUT MODULE WIRING

The following figure show how to connect RTDs.

3-20 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.2 WIRING

Three-wire shielded cable

RTD terminals

Maximum total lead resistance: 25 ohms for Platinum RTDs

Route cable in separate conduit from current carrying conductors

RTD

859736A1.CDR

RTD terminals

RTD

For RTD

RTD

SURGE

~1 &

~8b

~1a

~1b

~2a

Hot

Return

Comp

~2c

~1c

NOTE

Figure 3–21: RTD CONNECTION

3.2.8 RS232 FACEPLATE PORT

A 9-pin RS232C serial port is located on the F35 faceplate for programming with a computer. All that is required to use this interface is a computer running the EnerVista UR Setup software provided with the relay. Cabling for the RS232 port is shown in the following figure for both 9-pin and 25-pin connectors.

The baud rate for this port is fixed at 19200 bps.

Figure 3–22: RS232 FACEPLATE PORT CONNECTION

GE Multilin F35 Multiple Feeder Protection System 3-21

3.2 WIRING 3 HARDWARE

NOTE

842722A3.CDR

100Base-T

COMMON

—

D1a D2a D3a D4b D4a

BNC

IRIG-B

input

CPU V

Co-axial cable

Shielded twisted-pairs

Ground at

remote device

RS485

COM2

100Base-T

COMMON

—

D1a D2a D3a D4b D4a

BNC

IRIG-B

input

CPU U

Co-axial cable

Shielded twisted-pairs

Ground at

remote device

RS485

COM2

100Base-T

100Base-FX

Port 1

Port 2

100Base-FX

Tx1

Rx1

COMMON

—

D1a D2a D3a D4b D4a

BNC

IRIG-B

input

CPU T

Co-axial cable

Shielded twisted-pairs

MM fiber-

optic cable

Ground at

remote device

RS485

COM2

100Base-FX

Tx2

Rx2

Tx3

Rx3

Tx1

Rx1

Port 3

Port 1

Port 2

Port 3

Port 1

Port 2

Port 3

100Base-FX

Tx1

Rx1

a) OVERVIEW

In addition to the faceplate RS232 port, the F35 provides a rear RS485 communication port.

The CPU modules do not require a surge ground connection.

3.2.9 CPU COMMUNICATION PORTS

Figure 3–23: CPU MODULE COMMUNICATIONS WIRING

b) RS485 PORTS

RS485 data transmission and reception are accomplished over a single twisted pair with transmit and receive data alternating over the same two wires. Through the use of the port, continuous monitoring and control from a remote computer, SCADA system, or PLC is possible.

To minimize errors from noise, the use of shielded twisted pair wire is recommended. Correct polarity must also be observed. For instance, the relays must be connected with all RS485 “+” terminals connected together, and all RS485 “–” terminals connected together. Though data is transmitted over a two-wire twisted pair, all RS485 devices require a shared reference, or common voltage. This common voltage is implied to be a power supply common. Some systems allow the shield (drain wire) to be used as common wire and to connect directly to the F35 COM terminal (#3); others function correctly only if the common wire is connected to the F35 COM terminal, but insulated from the shield.

3-22 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.2 WIRING

SCADA / PLC / computer

Optocoupler

Data

UR-series device

Shield

827757AA.CDR

Last device

Z (*)

Z (*) Terminating impedance at

each end (typically 120 Ω and 1 nF)

Twisted pair

RS485 +

RS485 –

COMP 485COM

Relay

Ground shield at SCADA / PLC /

computer only or at

UR-series device only

Data

Optocoupler

Up to 32 devices,

maximum 4000 feet

(1200 m)

Z (*)

RS485 +

RS485 –

COMP 485COM

RS485 + RS485 –

COMP 485COM

COM

To avoid loop currents, ground the shield at only one point. If other system considerations require the shield to be grounded at more than one point, install resistors (typically 100 ohms) between the shield and ground at each grounding point. Each relay needs to be daisy-chained to the next one in the link. A maximum of 32 relays can be connected in this manner without exceeding driver capability. For larger systems, additional serial channels must be added. It is also possible to use commercially available repeaters to have more than 32 relays on a single channel. Avoid star or stub connections entirely.

Lightning strikes and ground surge currents can cause large momentary voltage differences between remote ends of the communication link. For this reason, surge protection devices are internally provided at both communication ports. An isolated power supply with an optocoupled data interface also acts to reduce noise coupling. To ensure maximum reliability, all equipment should have similar transient protection devices installed.

Terminate both ends of the RS485 circuit with an impedance as shown below.

c) 100BASE-FX FIBER OPTIC PORTS

Ensure that the dust covers are installed when the fiber is not in use. Dirty or scratched connectors can lead to high losses on a fiber link.

The fiber optic communication ports allow for fast and efficient communications between relays at 100 Mbps. Optical fiber can be connected to the relay supporting a wavelength of 1310 nm in multi-mode.

GE Multilin F35 Multiple Feeder Protection System 3-23

Figure 3–24: RS485 SERIAL CONNECTION

3.2 WIRING 3 HARDWARE

UR-series device

BNC (in)

Receiver

RG58/59 coaxial cable

GPS satellite system

GPS connection

IRIG-B (–)

827756A8.CDR

IRIG-B time code generator

(DC-shift or amplitude modulated signal can be used)

IRIG-B (+)

UR-series device

BNC (in)

Receiver

Twisted-pair cable

GPS satellite system

GPS connection

IRIG-B (–)

IRIG-B time code generator

(DC-shift or amplitude modulated signal can be used)

IRIG-B (+)

NOTE

IRIG-B is a standard time code format that allows stamping of events to be synchronized among connected devices. The IRIG-B code allows time accuracies of up to 100 ns. Using the IRIG-B input, the F35 operates an internal oscillator with 1 µs resolution and accuracy. The IRIG time code formats are serial, pulse width-modulated codes that can be either DC level shifted or amplitude modulated (AM). The GE MultiSync 100 1588 GPS Clock as well as third-party equipment are available for generating the IRIG-B signal; this equipment can use a global positioning system (GPS) satellite system to obtain the time reference so that devices at different geographic locations can be synchronized.

3.2.10 IRIG-B

Figure 3–25: OPTIONS FOR THE IRIG-B CONNECTION

Using an amplitude modulated receiver causes errors up to 1 ms in event time-stamping. The F35 is intended for use with external clocks that set the IRIG-B control bits according to IEEE Std C37.118.1-

2011. When used with a source that sets the IRIG-B control bits according to IEEE Std 1344-1995, the source must have the sign of its local time offset setting reversed, and if daylight savings time (DST) is used, the source's DST start and DST stop date settings must be interchanged.

3-24 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

842006A2.CDR

UR 1

UR 2

UR 3

UR 4

842007A3.CDR

Tx1

UR 1

Tx2

Rx1

Rx2

Tx1

UR 2

Tx2

Rx1

Rx2

Tx1

UR 3

Tx2

Rx1

Rx2

Tx1

UR 4

Tx2

Rx1

Rx2

3.3DIRECT INPUT/OUTPUT COMMUNICATIONS 3.3.1 DESCRIPTION

The direct inputs and outputs feature makes use of the type 7 series of communications modules, which allow direct messaging between UR devices. These communications modules are outlined in the table later in this section.

The communications channels are normally connected in a ring configuration as shown in the following figure. The transmitter of one module is connected to the receiver of the next module. The transmitter of this second module is then connected to the receiver of the next module in the ring. This is continued to form a communications ring. The figure illustrates a ring of four UR-series relays with the following connections: UR1-Tx to UR2-Rx, UR2-Tx to UR3-Rx, UR3-Tx to UR4-Rx, and UR4-Tx to UR1-Rx. A maximum of 16 UR-series relays can be connected in a single ring

Figure 3–26: DIRECT INPUT AND OUTPUT SINGLE CHANNEL CONNECTION

The interconnection for dual-channel type 7 communications modules is shown as follows. Two channel modules allow for a redundant ring configuration. That is, two rings can be created to provide an additional independent data path. The required connections are: UR1-Tx1 to UR2-Rx1, UR2-Tx1 to UR3-Rx1, UR3-Tx1 to UR4-Rx1, and UR4-Tx1 to UR1-Rx1 for the first ring; and UR1-Tx2 to UR4-Rx2, UR4-Tx2 to UR3-Rx2, UR3-Tx2 to UR2-Rx2, and UR2-Tx2 to UR1-Rx2 for the second ring.

Figure 3–27: DIRECT INPUT AND OUTPUT DUAL CHANNEL CONNECTION

The following diagram shows the connection for three UR-series relays using two independent communication channels. UR1 and UR3 have single type 7 communication modules; UR2 has a dual-channel module. The two communication channels can be of different types, depending on the Type 7 modules used. To allow the direct input and output data to cross- over from channel 1 to channel 2 on UR2, the

DIRECT I/O CHANNEL CROSSOVER setting should be “Enabled” on UR2. This

forces UR2 to forward messages received on Rx1 out Tx2, and messages received on Rx2 out Tx1.

GE Multilin F35 Multiple Feeder Protection System 3-25

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

842013A2.CDR

Channel 1

Channel 2

Tx1

UR 2

Tx2

Rx1

Rx2

UR 1

UR 3

7A, 7B, and

7C modules

7H, 7I, and

7J modules

1 channel 2 channels

Rx1

Rx2

Tx1 Tx1

Tx2

831719A3.CDR

Figure 3–28: DIRECT INPUT AND OUTPUT SINGLE/DUAL CHANNEL COMBINATION CONNECTION

The inter-relay communications modules are available with several interfaces and some are outlined here in more detail. Those that apply depend on options purchased. The options are outlined in the Inter-Relay Communications section of the Order Code tables in Chapter 2. All of the fiber modules use ST type connectors.

3.3.2 FIBER: LED AND ELED TRANSMITTERS

The following figure shows the configuration for the 7A, 7B, 7C, 7H, 7I, and 7J fiber-only modules.

3-26 F35 Multiple Feeder Protection System GE Multilin

Figure 3–29: LED AND ELED FIBER MODULES

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

1 channel 2 channels

Rx1 Rx1

Rx2

Tx1 Tx1

Tx2

831720A5.CDR

72 and 7D

modules

73 and 7K

modules

2 channels

Tx1

Tx2

Rx1

Rx2

831827A1.CDR

2I and 2J

modules

CAUTION

NOTICE

3.3.3 FIBER-LASER TRANSMITTERS

The following figure shows the configuration for the 72, 73, 7D, and 7K fiber-laser modules.

Figure 3–30: 7X LASER FIBER MODULES

The following figure shows configuration for the 2I and 2J fiber-laser module.

GE Multilin F35 Multiple Feeder Protection System 3-27

Figure 3–31: 2I AND 2J LASER FIBER MODULE

Observing any fiber transmitter output can injure the eye.

When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the maximum optical input power to the receiver.

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

842773A3.CDR

~8a ~8b

Rx +

Tx +

Shield Tx –

Shield

Rx –

Tx –

Rx +

Tx +

Rx –

G.703 communications

~2b

~6a

~7a

~1b

~1a

~3a

~6b

~7b

~2a

~3b

G.703 channel 2

G.703 channel 1

Surge

X8a

X8b

Rx +

Tx +

Shield Tx –

Shield

Rx –

Tx –

Rx +

Tx +

Rx –

G.703 communications

X2b

X6a

X7a

X1b

X1a

X3a

X6b

X7b

X2a

X3b

G.703 channel 2

G.703 channel 1

Surge

831727A5.CDR

X8a X8b

Rx +

Tx +

Shield Tx –

Shield

Rx –

Tx –

Rx +

Tx +

Rx –

G.703 communications

X2b

X6a

X7a

X1b

X1a

X3a

X6b

X7b

X2a

X3b

G.703 channel 2

G.703 channel 1

Surge

NOTE

3.3.4 G.703 INTERFACE

a) DESCRIPTION

The following figure shows the 64K ITU G.703 co-directional interface configuration.

The G.703 module is fixed at 64 kbps. The SETTINGS > PRODUCT SETUP > DIRECT I/O > DIRECT I/O DATA RATE setting is not applicable to this module.

AWG 24

twisted shielded pair is recommended for external connections, with the shield grounded only at one end. Con-

necting the shield to pin X1a or X6a grounds the shield since these pins are internally connected to ground. Thus, if pin X1a or X6a is used to ground the shield at one end, do not ground the shield at the other end. This interface module is protected by surge suppression devices.

Figure 3–32: G.703 INTERFACE CONFIGURATION

The following figure shows the typical pin interconnection between two G.703 interfaces. For the actual physical arrangement of these pins, see the Rear Terminal Layout section earlier in this chapter. All pin interconnections are to be maintained for a connection to a multiplexer.

b) G.703 SELECTION SWITCH PROCEDURES

1. With the power to the relay off, remove the G.703 module (7R or 7S) as follows. Record the original location of the

2. Simultaneously pull the ejector/inserter clips located at the top and at the bottom of each module in order to release the

3. Remove the module cover screw.

4. Remove the top cover by sliding it towards the rear and then lift it upwards.

5. Set the timing selection switches (channel 1, channel 2) to the desired timing modes.

3-28 F35 Multiple Feeder Protection System GE Multilin

Figure 3–33: TYPICAL PIN INTERCONNECTION BETWEEN TWO G.703 INTERFACES

Pin nomenclature can differ from one manufacturer to another. Therefore, it is not uncommon to see pinouts numbered TxA, TxB, RxA and RxB. In such cases, it can be assumed that “A” is equivalent to “+” and “B” is equivalent to “–”.

module to help ensure that the same or replacement module is inserted into the correct slot.

module for removal.

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

Cover screw

Top cover

Bottom cover

Ejector/inserter clip

Timing selection

switches

Channel 1

Channel 2

FRONT

REAR

831774A3.CDR

6. Replace the top cover and the cover screw.

7. Re-insert the G.703 module. Take care to ensure that the correct module type is inserted into the correct slot position. The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged position as the module is smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module is fully inserted.

Figure 3–34: G.703 TIMING SELECTION SWITCH SETTING

Table 3–3: G.703 TIMING SELECTIONS

SWITCHES FUNCTION

S1 OFF → octet timing disabled

S5 and S6 S5 = OFF and S6 = OFF → loop timing mode

c) G.703 OCTET TIMING

ON → octet timing 8 kHz

S5 = ON and S6 = OFF → internal timing mode S5 = OFF and S6 = ON → minimum remote loopback mode S5 = ON and S6 = ON → dual loopback mode

If octet timing is enabled (ON), this 8 kHz signal is asserted during the violation of bit 8 (LSB) necessary for connecting to higher order systems. When F35s are connected back-to-back, octet timing is disabled (OFF).

d) G.703 TIMING MODES

There are two timing modes for the G.703 module: internal timing mode and loop timing mode (default).

• Internal Timing Mode: The system clock is generated internally. Therefore, the G.703 timing selection should be in the internal timing mode for back-to-back (UR-to-UR) connections. For back-to-back connections, set for octet timing (S1 = OFF) and timing mode to internal timing (S5 = ON and S6 = OFF).

• Loop Timing Mode: The system clock is derived from the received line signal. Therefore, the G.703 timing selection should be in loop timing mode for connections to higher order systems. For connection to a higher order system (UR-

GE Multilin F35 Multiple Feeder Protection System 3-29

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

842752A2.CDR

Internal timing mode

Loop timing mode

(factory default)

DMR

DMX

G7X

G7R

DMR = Differential Manchester Receiver DMX = Differential Manchester Transmitter G7X = G.703 Transmitter G7R = G.703 Receiver

842774A1.CDR

DMR

DMX

G7X

G7R

DMR = Differential Manchester Receiver DMX = Differential Manchester Transmitter G7X = G.703 Transmitter G7R = G.703 Receiver

842775A1.CDR

to-multiplexer, factory defaults), set to octet timing (S1 = ON) and set timing mode to loop timing (S5 = OFF and S6 = OFF).

The switch settings for the internal and loop timing modes are shown below:

e) G.703 TEST MODES

In minimum remote loopback mode, the multiplexer is enabled to return the data from the external interface without any processing to assist in diagnosing G.703 line-side problems irrespective of clock rate. Data enters from the G.703 inputs, passes through the data stabilization latch which also restores the proper signal polarity, passes through the multiplexer and then returns to the transmitter. The differential received data is processed and passed to the G.703 transmitter module after which point the data is discarded. The G.703 receiver module is fully functional and continues to process data and passes it to the differential Manchester transmitter module. Since timing is returned as it is received, the timing source is expected to be from the G.703 line side of the interface.

In dual loopback mode, the multiplexers are active and the functions of the circuit are divided into two with each receiver/ transmitter pair linked together to deconstruct and then reconstruct their respective signals. Differential Manchester data enters the Differential Manchester receiver module and then is returned to the differential Manchester transmitter module. Likewise, G.703 data enters the G.703 receiver module and is passed through to the G.703 transmitter module to be returned as G.703 data. Because of the complete split in the communications path and because, in each case, the clocks are extracted and reconstructed with the outgoing data, in this mode there must be two independent sources of timing. One source lies on the G.703 line side of the interface while the other lies on the differential Manchester side of the interface.

3-30 F35 Multiple Feeder Protection System GE Multilin

Figure 3–35: G.703 MINIMUM REMOTE LOOPBACK MODE

Figure 3–36: G.703 DUAL LOOPBACK MODE

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

Shield

COM

Tx +

Tx –

Rx –

Rx +

Clock

RS422

channel 1

RS422

channel 2

Surge

2b 8a

Inter-relay communications 7W

842776A3.CDR

Dual-channel RS422 module

Shield

Tx +

Tx –

Rx –

Rx +

RS422

COM

Clock

Surge

2b 8a

Inter-relay comms. 7T

Single-channel RS422 module

~ indicates the slot position

831728A5.CDR

W8a

Shield

Tx – Rx – Tx + Rx +

RS422 communications

W4b

W3a

W3b

W6a

W2a

RS422 channel 1

Surge

+ –

W7a W8b

Clock

Common

W2b

COM

W8a

Shield

Tx – Rx – Tx + Rx +

RS422 communications

W4b

W3a

W3b

W6a

W2a

RS422 channel 1

Surge

+ –

W7a W8b

Clock

Common

W2b

COM

–

64 or 128 kbps

3.3.5 RS422 INTERFACE

a) DESCRIPTION

There are two RS422 inter-relay communications modules available: single-channel RS422 (module 7T) and dual-channel RS422 (module 7W). The modules can be configured to run at 64 kbps or 128 kbps. AWG 20-24 twisted shielded pair cable is recommended for external connections. These modules are protected by optically-isolated surge suppression devices.

The shield pins (6a and 7b) are internally connected to the ground pin (8a). Proper shield termination is as follows:

• Site 1: Terminate shield to pins 6a or 7b or both.

• Site 2: Terminate shield to COM pin 2b.

Match the clock terminating impedance with the impedance of the line.

The following figure shows the typical pin interconnection between two single-channel RS422 interfaces installed in slot W. All pin interconnections are to be maintained for a connection to a multiplexer.

b) TWO-CHANNEL APPLICATION VIA MULTIPLEXERS

The RS422 interface can be used for single channel or two channel applications over SONET/SDH or multiplexed systems. When used in single-channel applications, the RS422 interface links to higher order systems in a typical fashion observing transmit (Tx), receive (Rx), and send timing (ST) connections. However, when used in two-channel applications, certain criteria must be followed since there is one clock input for the two RS422 channels. The system functions correctly when the following connections are observed and your data module has a terminal timing feature. Terminal timing is a common feature to most synchronous data units that allows the module to accept timing from an external source. Using the terminal timing feature, two channel applications can be achieved if these connections are followed: The send timing outputs from the multiplexer (data module 1), connects to the clock inputs of the UR–RS422 interface in the usual fashion. In addition, the send timing outputs of data module 1 is also paralleled to the terminal timing inputs of data module 2. By using this configuration, the timing for both data modules and both UR–RS422 channels are derived from a single clock source. As a result, data sampling for both of the UR–RS422 channels is synchronized via the send timing leads on data module 1 as shown below. If the terminal timing feature is not available or this type of connection is not desired, the G.703 interface is a viable option that does not impose timing restrictions.

GE Multilin F35 Multiple Feeder Protection System 3-31

Figure 3–37: RS422 INTERFACE CONNECTIONS

Figure 3–38: TYPICAL PIN INTERCONNECTION BETWEEN TWO RS422 INTERFACES

Data module 1

Data module 2

Signal name

SD(A) - Send data

TT(A) - Terminal timing

TT(B) - Terminal timing

SD(B) - Send data

RD(A) - Received data

SD(A) - Send data

SD(B) - Send data

RD(B) - Received data

RS(A) - Request to send (RTS)

RT(A) - Receive timing

CS(A) - Clear To send

RT(B) - Receive timing

CS(B) - Clear To send

Local loopback

Remote loopback

Signal ground

ST(A) - Send timing

ST(B) - Send timing

RS(B) - Request to send (RTS)

831022A3.CDR

Shld.

Tx1(+)

Tx2(+)

Tx1(-)

Tx2(-)

Rx1(+)

Rx2(+)

com

Rx1(-)

Rx2(-)

–

INTER-RELAY COMMUNICATIONS

RS422

CHANNEL 1

RS422

CHANNEL 2

CLOCK

SURGE

831733A1.CDR

Tx Clock

Tx Data

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

Figure 3–39: TIMING CONFIGURATION FOR RS422 TWO-CHANNEL, THREE-TERMINAL APPLICATION

Data module 1 provides timing to the F35 RS422 interface via the ST(A) and ST(B) outputs. Data module 1 also provides timing to data module 2 TT(A) and TT(B) inputs via the ST(A) and AT(B) outputs. The data module pin numbers have been omitted in the figure above since they vary by manufacturer.

c) TRANSMIT TIMING

The RS422 interface accepts one clock input for transmit timing. It is important that the rising edge of the 64 kHz transmit timing clock of the multiplexer interface is sampling the data in the center of the transmit data window. Therefore, it is important to confirm clock and data transitions to ensure proper system operation. For example, the following figure shows the positive edge of the Tx clock in the center of the Tx data bit.

3-32 F35 Multiple Feeder Protection System GE Multilin

Figure 3–40: CLOCK AND DATA TRANSITIONS

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

NOTICE

Tx2

Rx2

842777A2.CDR

~8a

7L, 7M, 7N,

7P, and 74

Shield

Tx – Rx – Tx + Rx +

RS422

communications

~4b

~3a

~3b

~6a

~2a

RS422 channel 1

Surge

+ –

~7a ~8b

Clock channel 1

Common

~2b

COM

Fiber channel 2

NOTICE

d) RECEIVE TIMING

The RS422 interface utilizes NRZI-MARK modulation code and; therefore, does not rely on an Rx clock to recapture data. NRZI-MARK is an edge-type, invertible, self-clocking code.

To recover the Rx clock from the data-stream, an integrated DPLL (digital phase lock loop) circuit is utilized. The DPLL is driven by an internal clock, which is 16-times over-sampled, and uses this clock along with the data-stream to generate a data clock that can be used as the SCC (serial communication controller) receive clock.

3.3.6 RS422 AND FIBER INTERFACE

The following figure shows the combined RS422 plus fiberoptic interface configuration at 64K baud. The 7L, 7M, 7N, 7P, and 74 modules are used in two-terminal with a redundant channel or three-terminal configurations where channel 1 is employed via the RS422 interface (possibly with a multiplexer) and channel 2 via direct fiber.

AWG 20-24

twisted shielded pair is recommended for external RS422 connections and ground the shield only at one end.

For the direct fiber channel, address power budget issues properly.

When using a LASER Interface, attenuators can be necessary to ensure that you do not exceed maximum optical input power to the receiver.

Figure 3–41: RS422 AND FIBER INTERFACE CONNECTION

Connections shown above are for multiplexers configured as DCE (data communications equipment) units.

3.3.7 G.703 AND FIBER INTERFACE

The figure below shows the combined G.703 plus fiberoptic interface configuration at 64 kbps. The 7E, 7F, 7G, 7Q, and 75 modules are used in configurations where channel 1 is employed via the G.703 interface (possibly with a multiplexer) and channel 2 via direct fiber. AWG 24 twisted shielded pair is recommended for external G.703 connections connecting the shield to pin 1a at one end only. For the direct fiber channel, address power budget issues properly. See previous sections for additional details on the G.703 and fiber interfaces.

When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the maximum optical input power to the receiver.

GE Multilin F35 Multiple Feeder Protection System 3-33

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

Rx2

Tx2

842778A2.CDR

~3b

75, 7E, 7F, 7G,

and 7Q

Rx +

Shield Tx – Rx – Tx +

G.703

communications

~2b

~1b

~1a

~3a

~2a

G.703 channel 1

Surge

Fiber channel 2

UR-series

device

IEEE C37.94 fiber interface

up to 2 km

842755A2.CDR

Digital multiplexer, IEEE C37.94

compliant

Figure 3–42: G.703 AND FIBER INTERFACE CONNECTION

3.3.8 IEEE C37.94 INTERFACE

The UR-series IEEE C37.94 communication modules (modules types 2G, 2H, 2I, 2J, 76, and 77) are designed to interface with IEEE C37.94 compliant digital multiplexers or an IEEE C37.94 compliant interface converter for use with direct input and output applications. The IEEE C37.94 standard defines a point-to-point optical link for synchronous data between a multiplexer and a teleprotection device. This data is typically 64 kbps, but the standard provides for speeds up to 64n kbps, where n = 1, 2,…, 12. The UR-series C37.94 communication modules are either 64 kbps (with n fixed at 1) for 128 kbps (with n fixed at 2). The frame is a valid International Telecommunications Union (ITU-T) recommended G.704 pattern from the standpoint of framing and data rate. The frame is 256 bits and is repeated at a frame rate of 8000 Hz, with a resultant bit rate of 2048 kbps.

The specifications for the module are as follows:.

• IEEE standard: C37.94 for 1 × 128 kbps optical fiber interface (for 2G and 2H modules) or C37.94 for 2 × 64 kbps optical fiber interface (for 76 and 77 modules)

• Fiber optic cable type: 50 nm or 62.5 µm core diameter optical fiber

• Fiber optic mode: multimode

• Fiber optic cable length: up to 2 km

• Fiber optic connector: type ST

• Wavelength: 820 ±40 nm

• Connection: as per all fiber optic connections, a Tx to Rx connection is required

The UR-series C37.94 communication module can be connected directly to any compliant digital multiplexer that supports the IEEE C37.94 standard shown as follows.

3-34 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

UR-series

device

up to 2 km

IEEE C37.94

converter

RS422

interface

842756A2.CDR

IEEE C37.94

fiber interface

Digital

multiplexer

with EIA-422

interface

842753A2.CDR

Internal timing mode

Loop timing mode

(factory default)

The UR-series C37.94 communication module can be connected to the electrical interface (G.703, RS422, or X.21) of a non-compliant digital multiplexer via an optical-to-electrical interface converter that supports the IEEE C37.94 standard, shown as follows.

In 2008, GE Grid Solutions released revised modules 76 and 77 for C37.94 communication to enable multi-ended fault location functionality with firmware 5.60 release and higher. All modules 76 and 77 shipped the change support this feature and are fully backward compatible with firmware releases below 5.60. For customers using firmware release 5.60 and higher, the module can be identified with "Rev D" printed on the module and is to be used on all ends of F35 communication for two and three terminal applications. Failure to use it at all ends results in intermittent communication alarms. For customers using firmware revisions below 5.60, it is not required to match the revision of the modules installed.

The UR-series C37.94 communication module has six switches to set the clock configuration. The following figure shows the functions of these control switches.

For the internal timing mode, the system clock is generated internally. Therefore, the timing switch selection should be internal timing for relay 1 and loop timed for relay 2. There must be only one timing source configured.

For the looped timing mode, the system clock is derived from the received line signal. Therefore, the timing selection should be in loop timing mode for connections to higher order systems.

The IEEE C37.94 communications module cover removal procedure is as follows:

1. With power to the relay off, remove the IEEE C37.94 module (type 2G, 2H, 2I, 2J, 76 or 77 module) as follows. Record

the original location of the module to help ensure that the same or replacement module is inserted into the correct slot.

2. Simultaneously pull the ejector/inserter clips located at the top and at the bottom of each module in order to release the

module for removal.

3. Remove the module cover screw.

4. Remove the top cover by sliding it towards the rear and then lift it upwards.

5. Set the timing selection switches (channel 1, channel 2) to the desired timing modes (see description above).

6. Replace the top cover and the cover screw.

7. Re-insert the IEEE C37.94 module. Take care to ensure that the correct module type is inserted into the correct slot

position. The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged position as the module is smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module is fully inserted.

GE Multilin F35 Multiple Feeder Protection System 3-35

Cover screw

Top cover

Bottom cover

Ejector/inserter clip

Timing selection

switches

Channel 1

Channel 2

FRONT

REAR

831774A3.CDR

Tx1

Tx2

Rx1

Rx2

Tx1

Tx2

CH1 Link/Activity LED

CH2 Link/Activity LED

COMMS

C37.94SM 1300nm single-mode ELED 2 channel

Technical support: Tel: (905)294-6222 Fax: (905)201-2098 (NORTH AMERICA)

1 800 547-8629

Made in Canada

GE Multilin

REV. D

CH1 Clock Configuration LED CH2 Clock Configuration LED

FRONT VIEW REAR VIEW

842837A1.cdr

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

Figure 3–43: IEEE C37.94 TIMING SELECTION SWITCH SETTING

Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the following figure.

The clock configuration LED status is as follows:

• Flashing green — loop timing mode while receiving a valid data packet

Figure 3–44: STATUS LEDS

3-36 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

UR-series

device

C37.94SM

fiber interface

up to 10 km

842757A2.CDR

Digital

multiplexer

C97.94SM

UR-series

device with

C37.94SM

module

C37.94SM

fiber interface

up to 10 km

UR-series

device with

C37.94SM

module

842758A2.CDR

• Flashing yellow — internal mode while receiving a valid data packet

• Solid red — (switch to) internal timing mode while not receiving a valid data packet The link/activity LED status is as follows:

• Flashing green — FPGA is receiving a valid data packet

• Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit"

• Solid red — FPGA is not receiving a valid packet or the packet received is invalid

3.3.9 C37.94SM INTERFACE

The UR-series C37.94SM communication modules (2A and 2B) are designed to interface with modified IEEE C37.94 compliant digital multiplexers or IEEE C37.94 compliant interface converters that have been converted from 820 nm multi-mode fiber optics to 1300 nm ELED single-mode fiber optics. The IEEE C37.94 standard defines a point-to-point optical link for synchronous data between a multiplexer and a teleprotection device. This data is typically 64 kbps, but the standard provides for speeds up to 64n kbps, where n = 1, 2,…, 12. The UR-series C37.94SM communication module is 64 kbps only with n fixed at 1. The frame is a valid International Telecommunications Union (ITU-T) recommended G.704 pattern from the standpoint of framing and data rate. The frame is 256 bits and is repeated at a frame rate of 8000 Hz, with a resultant bit rate of 2048 kbps.

The specifications for the module are as follows:

• Emulated IEEE standard: emulates C37.94 for 1 × 64 kbps optical fiber interface (modules set to n = 1 or 64 kbps)

• Fiber optic cable type: 9/125 μm core diameter optical fiber

• Fiber optic mode: single-mode, ELED compatible with HP HFBR-1315T transmitter and HP HFBR-2316T receiver

• Fiber optic cable length: up to 11.4 km

• Fiber optic connector: type ST

• Wavelength: 1300 ±40 nm

• Connection: as per all fiber optic connections, a Tx to Rx connection is required The UR-series C37.94SM communication module can be connected directly to any compliant digital multiplexer that sup-

ports C37.94SM as shown below.

It can also can be connected directly to any other UR-series relay with a C37.94SM module as shown below.

In 2008, GE Grid Solutions released revised modules 2A and 2B for C37.94SM communication to enable multi-ended fault location functionality with firmware 5.60 release and higher. All modules 2A and 2B shipped since the change support this feature and are fully backward compatible with firmware releases below 5.60. For customers using firmware release 5.60 and higher, the module can be identified with "Rev D" printed on the module and is to be used on all ends of F35 communication for two and three terminal applications. Failure to use it at all ends results in intermittent communication alarms. For

GE Multilin F35 Multiple Feeder Protection System 3-37

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

842753A2.CDR

Internal timing mode

Loop timing mode

(factory default)

customers using firmware revisions below 5.60, it is not required to match the revision of the modules installed. The UR-series C37.94SM communication module has six switches that are used to set the clock configuration. The func-

tions of these control switches are shown below.

For the looped timing mode, the system clock is derived from the received line signal. Therefore, the timing selection should be in loop timing mode for connections to higher order systems.

The C37.94SM communications module cover removal procedure is as follows:

1. With power to the relay off, remove the C37.94SM module (modules 2A or 2B) as follows. Record the original location of the module to help ensure that the same or replacement module is inserted into the correct slot.

2. Simultaneously pull the ejector/inserter clips located at the top and at the bottom of each module in order to release the module for removal.

3. Remove the module cover screw.

4. Remove the top cover by sliding it towards the rear and then lift it upwards.

5. Set the timing selection switches (channel 1, channel 2) to the desired timing modes (see description above).

6. Replace the top cover and the cover screw.

7. Re-insert the C37.94SM module. Take care to ensure that the correct module type is inserted into the correct slot position. The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged position as the module is smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module is fully inserted.

3-38 F35 Multiple Feeder Protection System GE Multilin

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

Cover screw

Top cover

Bottom cover

Ejector/inserter clip

Timing selection

switches

Channel 1

Channel 2

FRONT

REAR

831774A3.CDR

Tx1

Tx2

Rx1

Rx2

Tx1

Tx2

CH1 Link/Activity LED

CH2 Link/Activity LED

COMMS

C37.94SM 1300nm single-mode ELED 2 channel

Technical support: Tel: (905)294-6222 Fax: (905)201-2098 (NORTH AMERICA)

1 800 547-8629

Made in Canada

GE Multilin

REV. D

CH1 Clock Configuration LED CH2 Clock Configuration LED

FRONT VIEW REAR VIEW

842837A1.cdr

Figure 3–45: C37.94SM TIMING SELECTION SWITCH SETTING

Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the following figure.

The clock configuration LED status is as follows:

Figure 3–46: STATUS LEDS

• Flashing green — loop timing mode while receiving a valid data packet

GE Multilin F35 Multiple Feeder Protection System 3-39

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

• Flashing yellow — internal mode while receiving a valid data packet

• Solid red — (switch to) internal timing mode while not receiving a valid data packet

The link/activity LED status is as follows:

• Flashing green — FPGA is receiving a valid data packet

• Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit"

• Solid red — FPGA is not receiving a valid packet or the packet received is invalid

3-40 F35 Multiple Feeder Protection System GE Multilin

4 HUMAN INTERFACES 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE

4 HUMAN INTERFACES 4.1ENERVISTA UR SETUP SOFTWARE INTERFACE 4.1.1 INTRODUCTION

The EnerVista UR Setup software provides a graphical user interface (GUI) as one of two human interfaces to a UR device. The alternate human interface is implemented via the device’s faceplate keypad and display (see the Faceplate Interface section in this chapter).

The EnerVista UR Setup software provides a single facility to configure, monitor, maintain, and troubleshoot the operation of relay functions, connected over local or wide area communication networks. It can be used while disconnected (offline) or connected (online) to a UR device. In offline mode, settings files can be created for eventual downloading to the device. In online mode, you can communicate with the device in real-time.

The EnerVista UR Setup software is provided with every F35 relay and runs on Microsoft This chapter provides a summary of the basic EnerVista UR Setup software interface features. The EnerVista UR Setup Help File provides details for getting started and using the EnerVista UR Setup software interface.

To start using the EnerVista UR Setup software, site and device definition are required. See the EnerVista UR Setup Help File or refer to the EnerVista UR Setup Software section in Chapter 1 for details.

Windows XP, 7, and Server 2008.

4.1.2 CREATING A SITE LIST

4.1.3 ENERVISTA UR SETUP OVERVIEW

a) ENGAGING A DEVICE

The EnerVista UR Setup software can be used in online mode (relay connected) to directly communicate with the F35 relay. Communicating relays are organized and grouped by communication interfaces and into sites. Sites can contain any number of relays selected from the UR-series of relays.

b) USING SETTINGS FILES

The EnerVista UR Setup software interface supports three ways of handling changes to relay settings:

• In offline mode (relay disconnected) to create or edit relay settings files for later download to communicating relays

• While connected to a communicating relay to directly modify any relay settings via relay data view windows, and then

save the settings to the relay

• You can create/edit settings files and then write them to the relay while the interface is connected to the relay Settings files are organized on the basis of file names assigned by the user. A settings file contains data pertaining to the

following types of relay settings:

• Device definition

• Product setup

• System setup

• FlexLogic

• Grouped elements

• Control elements

• Inputs/outputs

• Remote resources

• Testing Factory default values are supplied and can be restored after any changes. The following communications settings are not transferred to the F35 with settings files:

Modbus Slave Address Modbus TCP Port Number RS485 COM2 Baud Rate RS485 COM2 Parity

GE Multilin F35 Multiple Feeder Protection System 4-1

4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE 4 HUMAN INTERFACES

COM2 Minimum Response Time COM2 Selection RRTD Slave Address RRTD Baud Rate IP Address IP Subnet Mask IP Routing

When a settings file is loaded to a F35 that is in-service, the following sequence occurs:

1. The F35 takes itself out of service.

2. The F35 issues a

3. The F35 closes the critical fail contact.

c) CREATING AND EDITING FLEXLOGIC

You create or edit a FlexLogic equation in order to customize the relay. You can subsequently view the automatically generated logic diagram.

d) VIEWING ACTUAL VALUES

You can view real-time relay data such as input/output status and measured parameters.

e) VIEWING TRIGGERED EVENTS

While the interface is in either online or offline mode, you can view and analyze data generated by triggered specified parameters, via one of the following:

• Event recorder

The event recorder captures contextual data associated with the last 1024 events, listed in chronological order from most recent to oldest.

• Oscillography

The oscillography waveform traces and digital states are used to provide a visual display of power system and relay operation data captured during specific triggered events.

UNIT NOT PROGRAMMED major self-test error.

f) FILE SUPPORT

• Execution: Any EnerVista UR Setup file that is opened launches the application or provides focus to the already opened application. If the file was a settings file (has a URS extension) that had been removed from the Settings List tree menu, it is added back to the Settings List tree menu.

• Drag and Drop: The Site List and Settings List control bar windows are each mutually a drag source and a drop target for device-order-code-compatible files or individual menu items. Also, the Settings List control bar window and any Windows Explorer directory folder are each mutually a file drag source and drop target.

New files that are dropped into the Settings List window are added to the tree, which is automatically sorted alphabetically with respect to settings file names. Files or individual menu items that are dropped in the selected device menu in the Site List window are automatically sent to the online communicating device.

g) FIRMWARE UPGRADES

The firmware of a F35 device can be upgraded, locally or remotely, via the EnerVista UR Setup software. The corresponding instructions are provided by the EnerVista UR Setup Help file under the topic “Upgrading Firmware”.

If you are upgrading from version 7.0 or 7.1 to 7.2 or later, some CPU modules require a new boot version. Update this first in EnerVista under Maintenance > Update Firmware.

Before backing up settings and upgrading, set the Settings > Product Setup > Security > Dual Permission Security Access > Remote Setting Authorized and Local Setting Authorized settings to "ON." Otherwise, the upgrade is blocked and results in an "Unable to put relay in flash mode" message.

4-2 F35 Multiple Feeder Protection System GE Multilin

GE UR F35 Series Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1.1.1 CAUTIONS AND WARNINGS

a) GENERAL CAUTIONS AND WARNINGS

1.1.2 INSPECTION PROCEDURE

1.2UR OVERVIEW 1.2.1 INTRODUCTION TO THE UR

1.2.2 HARDWARE ARCHITECTURE

a) UR BASIC DESIGN

b) UR SIGNAL TYPES

1.2.3 SOFTWARE ARCHITECTURE

1.3ENERVISTA UR SETUP SOFTWARE 1.3.1 SYSTEM REQUIREMENTS

1.3.2 INSTALLATION

1.3.3 CONFIGURING THE F35 FOR SOFTWARE ACCESS

a) OVERVIEW

b) CONFIGURING SERIAL COMMUNICATIONS

c) CONFIGURING ETHERNET COMMUNICATIONS

1.3.4 USING THE QUICK CONNECT FEATURE

a) USING QUICK CONNECT VIA THE FRONT PANEL RS232 PORT

b) USING QUICK CONNECT VIA THE REAR ETHERNET PORTS

1.3.5 CONNECTING TO THE F35 RELAY

1.3.6 SETTING UP CYBERSENTRY AND CHANGING DEFAULT PASSWORD

1.4UR HARDWARE 1.4.1 MOUNTING AND WIRING

1.4.2 COMMUNICATIONS

1.4.3 FACEPLATE DISPLAY

1.5USING THE RELAY 1.5.1 FACEPLATE KEYPAD

1.5.2 MENU NAVIGATION

1.5.3 MENU HIERARCHY

1.5.4 RELAY ACTIVATION

a) PASSWORD SECURITY

1.5.5 RELAY PASSWORDS

b) CYBERSENTRY

1.5.6 FLEXLOGIC CUSTOMIZATION

1.5.7 COMMISSIONING

2 PRODUCT DESCRIPTION 2.1INTRODUCTION 2.1.1 OVERVIEW

2.1.2 SECURITY

a) ENERVISTA SECURITY

b) PASSWORD SECURITY

c) CYBERSENTRY SECURITY

2.1.3 IEC 870-5-103 PROTOCOL

2.2ORDER CODES 2.2.1 OVERVIEW

2.2.2 ORDER CODES WITH ENHANCED CT/VT MODULES

2.2.3 ORDER CODES WITH PROCESS BUS MODULES

2.2.4 REPLACEMENT MODULES

2.3SIGNAL PROCESSING 2.3.1 UR SIGNAL PROCESSING

2.4.1 PROTECTION ELEMENTS

2.4.2 USER-PROGRAMMABLE ELEMENTS

2.4.3 MONITORING

2.4.4 METERING

2.4.5 INPUTS

2.4.6 POWER SUPPLY

2.4.7 OUTPUTS

2.4.8 COMMUNICATION PROTOCOLS

2.4.9 INTER-RELAY COMMUNICATIONS

2.4.10 ENVIRONMENTAL

2.4.11 TYPE TESTS

2.4.12 PRODUCTION TESTS

2.4.13 APPROVALS

2.4.14 MAINTENANCE

3 HARDWARE 3.1DESCRIPTION 3.1.1 PANEL CUTOUT

a) HORIZONTAL UNITS

b) VERTICAL UNITS

3.1.2 REAR TERMINAL LAYOUT

3.2WIRING 3.2.1 TYPICAL WIRING

3.2.2 DIELECTRIC STRENGTH

3.2.3 CONTROL POWER

3.2.4 CT/VT MODULES

3.2.5 PROCESS BUS MODULES

3.2.6 CONTACT INPUTS AND OUTPUTS

3.2.7 TRANSDUCER INPUTS/OUTPUTS

3.2.8 RS232 FACEPLATE PORT

a) OVERVIEW

3.2.9 CPU COMMUNICATION PORTS

b) RS485 PORTS

c) 100BASE-FX FIBER OPTIC PORTS

3.2.10 IRIG-B

3.3DIRECT INPUT/OUTPUT COMMUNICATIONS 3.3.1 DESCRIPTION

3.3.2 FIBER: LED AND ELED TRANSMITTERS

3.3.3 FIBER-LASER TRANSMITTERS