GE TPX24SIYBS Specification

TM

TPX24SIYBS—GE Profile™ “Built-In-Style” Side-by-Side Refrigerator

Case Dimensions (in inches/cm.)

Installation of Water and Electrical Outlets

28C-1/4					Water hook-up
					on the refrigerator
26-D3/8				Recommended single loop
	1''			of 1/4" copper water line
23E-7/8	(2.54 cm.)
				Allow 48" minimum water	24"
				line to enable refrigerator
				to be pulled forward.
					18"
69-3/4			35-3/4G	Recommended water line
A				location using recess
69-3/4F
				in rear wall	Rear Wall View
68-3/4
B
		40-3/8
		H		45-5/8I

Side View

Front View

Top View

For answers to your Monogram,®GE Profile

Performance Series,™ GE Profile,™ GE,

Hotpoint and RCA appliance questions, call

GE Answer Center® service, 800.626.2000.

Revised 10/97

VOLUME and

SHELF AREA

Manufacturer Certified to

ASSOCIATION OF HOME APPLIANCE MANUFACTURERS ANSI/AHAN HRF-1-1979

Total volume and shelf area are calculated by the Association of Home Appliance Manufacturers’ standards.

R

Listed by Underwriters Laboratories

R

TM

TPX24SIYBS—GE Profile™ “Built-In-Style” Side-by-Side Refrigerator

Rough-In Dimensions (in inches)

			Standard, New Construction and
			Replacement Installation
			Installation Tips to Maximize
			the Built-In Look
			•All wall/floor moulding should be
			removed prior to installation.
			•Water recess on rear wall
			recommended to prevent water
			line damage. 48" minimum length
	70-1/4"		1/4" diameter water line tubing
			recommended.
	36"		•When possible, recess both water
			line and electrical outlet. (See
			local codes)
	24"		•Front and rear leveling legs are
			adjustable for the “Built-In” look.
			(See owner’s manual)
			•If optional collar trim kit is to be
	Water	Electrical	used or anticipated, see collar
			trim installation on next page for
			different rough-in dimensions.
	3/4" Airspace
	(1/2" Gap + 1/4"
	Wall Plates)
	24"	25"
	Cabinet
		Counter
	24" Side panels
		Top

Revised 10/97

Door Panel Dimensions (in inches)

Freezer Panel

Freezer Panel

Without Dispenser

With Dispenser

Fresh Food Panel

Detail C

14-1/2"

Detail C

14-1/2"

19-5/16

Detail C

18-3/8"

18-13/16"

1/2"

18-3/8"

1"

1"

14-5/8"

14-5/8"

14-1/2"

67-1/8"

67-1/8"

34-5/16"

2"

2"

1"

1"

1"

The areas at the top of the panels need to be cut out of the panels. All other dotted lines indicate areas that must be routed out about 3/16" (5 mm) on the back of side panels 1/4" (6 mm) thick or more. For panels less than 1/4"

(6 mm) thick, these areas can be cut out of the filler panel.

Order your own custom wood panels to match cabinetry

or other decor.

—Fresh food compartment panels (19-5/16" wide x 67-1/8" high)

—Freezer panel with dispenser (14-1/2" wide x 18-13/16" high and 14-1/2" wide x 34-5/16" high)

—Freezer panel without dispenser (14-1/2" wide x 67-1/8" high)

Panels up to 1/4" thick will fit door frame with no special preparation.

• Add filler behind material thinner than 1/4" for proper fit.

Note: Panels up to 3/4" will require special routing area around handles. Dimensions may vary depending on depth of panel.

Detail C

1/8"

5/16"

Panels 1/4" thick or less

1/4" Max.

Example of Routing

Depth of material to be routed out

1"

1/4"	3/16"

Front

(Fresh Food panel shown)

Notch required at top corner as noted.