Page 1
11
229C4053P557-2
31-10567-2 05-04 JR
Installation
30” Electric
Instructions
Slide-In Range
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•
IMPORTANT — Save these
instructions for local inspector’s use.
• IMPORTANT — Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance
requires basic mechanical skills.
• Completion time – 1 to 3 hours
• Proper installation is the responsibility of
the installer.
• Product failure due to improper installation
is not covered under the Warranty.
WARNING — This appliance must
be properly grounded.
FOR YOUR SAFETY:
CAUTION: — For Personal Safety
remove house fuse or open circuit breaker
before beginning installation. Failure to do so
could result in serious injury or even death.
ANTI-TIP DEVICE
WARNING — To reduce the risk
of tipping, the appliance must be secured by
properly installed Anti-Tip bracket packed
with this appliance.
If the Anti-Tip device supplied with the range
does not fit this application, use the universal
Anti-Tip device WB2X7909.
WARNING —
• All ranges can tip
• Injury to persons could result
• Install Anti-Tip bracket packed
with range
• See Installation Instructions
If you pull the range out and away from the
wall for any reason, make sure the Anti-Tip
bracket is engaged when the range is pushed
back against the wall.
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com
Page 2
2
Installation Instructions
FOR YOUR SAFETY:
All rough-in and spacing dimensions must be
met for safe use of your range. Electricity to
the range can be disconnected at the outlet
without moving the range if the outlet is in
the preferred location (remove lower drawer).
To reduce the risk of burns or fire when
reaching over hot surface elements, cabinet
storage space above the cooktop should be
avoided. If cabinet storage space is to be
provided above the cooktop, the risk can
be reduced by installing a range hood that
sticks out at least 5″ beyond the front of the
cabinets. Cabinets installed above a cooktop
must be no deeper than 13″.
Be sure your appliance is properly installed
and grounded by a qualified technician.
PREPARE TO INSTALL THE RANGE
TOOLS YOU WILL NEED
Straight Edge
Drill with 1/8″ Bit
Hand or Saber Saw
Pencil
Safety Glasses
Tape Measure
REMOVE SHIPPING MATERIALS
Remove all parts from the plastic bag found
inside the prepack of the oven and save
packaging tape.
1
ANTI-TIP DEVICE INSTALLATION
Before placing range in the counter, check the
factory location of the stability device on the
back of the range. For convenience you can
hook the stability chain in the upper set of
holes. Make sure there is no structural
interference when using the upper set of holes.
Decide on a location
that has no electrical
wiring or plumbing.
With the long screw
provided anchor the
chain to the floor or wall.
Make sure the
screw is going
into the wall plate
or stud at the
base of the wall
at least 3/4″.
Attach the stability chain so that it lines up
with the bracket on the back of the range.
Tug the chain to make sure it is securely
fastened.
Take the packaging
tape and temporarily
attach the loose end
of the chain to the
rear of the countertop.
Slide the range
into the counter
leaving enough
space behind to attach
the chain to the bracket.
G
F
E
D
C
B
A
2
Backguard (some models)
Mainback
Bracket Optional
Location
Chain
Chain
Chain
Long
Screw
Washer
Tape
Wall
Plate
Washer
and
Screw
Bracket Factory
Location
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Chain
Page 3
MINIMUM CLEARANCES (CONT.)
MINIMUM DIMENSIONS BETWEEN
COOKTOP AND CABINETS OR WALLS
Electrical Outlet Area
(Back of counter in cutout not shown for clarity)
• The distance from the floor to the top
of the counter must be at least 35-7/8″.
The maximum countertop height is 38″.
Make sure the wall coverings, countertop and
cabinets around the cooktop can withstand
the heat (up to 200°F) generated by the range.
NOTE: Dimension for Wall to Front of Door
Handle (door closed).
*28″ FOR MODELS – JSP26, JSS26, JSC26,
JSS16, RS734, RS504
**28-1/2″ FOR MODELS – JSP39, JSP38, JSP31,
JSP28, RS744, RS622, JS960, JSP40, JSP34
3
3
Installation Instructions
MINIMUM CLEARANCES
• The distance from the floor to the top
of the counter must be at least 35-7/8″.
The maximum counter height is 38″.
• 30″ ranges conform to U.L. requirements
for 0″ spacing from vertical walls above
countertops. However, some kitchen cabinet
finishes can be damaged by heat from the
range surface elements. Where varnished
wood or plastic film finishes are used,
a minimum clearance of 6″ must be
maintained.
• For listed over-the-range microwave
ovens, the microwave ovens can be
installed above the cooktop as per
manufacturer’s installation instructions.
• The range may be placed with 0″ clearance
(flush) at the back wall and side walls if the
range side trims extend beyond the cabinet
fronts at least 1/4″.
• See Figures 1 and 2 for all rough-in and
spacing dimensions. These dimensions
must be met for safe use of your range.
The location of the electrical outlet may
be changed as needed, but electricity to
the range can be disconnected at the outlet
without moving the range if the outlet is
in the suggested location (remove lower
drawer).
3
ANTI-TIP DEVICE INSTALLATION
(CONT.)
Slip the nearest link of the chain onto the
bracket. Pull to make sure it is as snug as
possible.
Slide the range all the way back. It is
normal to have some slack in the chain,
but it should not be excessive.
I
H
2
0”
18” Min.
30” Min.
0”
6”
Min.
6”
4
1
⁄2”
2
1
⁄4”
30”
36”
30”
Acceptable
electrical
outlet area.
Backguard (some models)
Mainback
Bracket Optional
Location
Chain
Bracket Factory
Location
281⁄2”** Wall to front
of door handle
(door closed) 45”
with door open
Fig. 5
Fig. 6
Fig. 7
28”*
1
⁄4”
5”
Page 4
4
Installation Instructions
PREPARE TO INSTALL THE RANGE
(CONT.)
PREPARATION
• Remove all tape and packaging. Be sure to
remove clear plastic film that covers some
chrome parts (around glass oven doors,
side trim) and any tape and packaging from
inside the oven.
• Take the accessory pack out of the oven.
• Check to be sure that no range parts have
come loose during shipping.
REMOVING PACKAGING
MATERIAL
Any packaging materials must
be removed during installation.
This will include adhesive tape, wire ties,
cardboard and protective plastic. Failure
to remove these materials could result in
damage to the appliance once the appliance
has been turned on and surfaces have heated.
4
PREPARE THE COUNTER
If you have an existing 30″ wide cutout that
goes all the way to the wall, you have the
option to buy a 4″ Backguard, Model #JXS31
(white), JXS32 (chrome), JXS33 (almond),
JXS34 (black), or JXS35 (bisque) or a Main
Top Rear Filler Kit, Model # JXS62BB (black),
JXS63WW (white), JXS64AA (almond), or
JXS65CC (bisque). These kits are available
through your GE dealer, if the existing cutout
is in a counter that has a backsplash (postformed top) we recommend that you use the
4″ backguard kit.
5
PREPARING THE COUNTER
(CONT.)
Determine the dimension of your cutout.
See Fig. 9 and Fig. 10. Dimensions given are
from front of counter and not from cabinet
face. To minimize chipping you may want
to apply masking tape to the counter and
mark the cut on top of the tape. Use a hand
or saber saw to make the cut. For best
appearance it is important that the cut be
smooth and straight.
If you are NOT using the Filler or Backguard:
If you have a countertop deeper than 25″
and you wish to set the range further back
into the counter, the cutout may be cut
deeper (up to 24-1/2″), but there must be
at least 24-1/2″ from the front edge of the
countertop and back wall.
5
Filler Strip
Screw
Speed Clip
23-3/16”
30”
Fig. 9
Fig. 8
Page 5
5
Installation Instructions
PREPARE THE COUNTER (CONT.)
If you are using the Filler or Backguard:
NOTE: If the distance from the back wall
to the front of the counter backsplash
(Dimension A in Fig. 11) is greater than the
standard 1-1/8″, there will be a small gap
between the wall behind the range and the
backguard. This is normal and should not
be visually objectionable.
5
SIDE TRIM EXTENSION KIT
If there is a small gap between the sides of
the range and the cabinets (up to 1/4″ each
side), you can order a side trim extension kit,
Pub, #3-A040, through the GE service center.
6
25”
30”
A
Fig. 11
Fig. 10
Page 6
6
Installation Instructions
6
ELECTRICAL CONNECTIONS
TO MAKE ELECTRICAL CONNECTION
• Remove the junction block access cover
(on range back). See Fig. 12A or 12B.
SOME MODELS will have a one-piece wire
cover shown in Fig. 12B. When re-installing
one-piece wire cover, make sure that wire
does not become pinched between wire
cover and mainback.
• All new constructions, mobile homes,
recreational vehicle and installations where
local codes do not allow grounding through
neutral, require a four-wire flexible cord kit.
If the range is rated between 8,750 and
16,500 watts, a range cord kit rated for
40 amps and a minimum of 125/250 Volts
is required. If the range is rated between
16,501 and 22,500 watts, a range cord kit
rated for 50 amps and a minimum of
125/250 Volts is required. For existing
construction, a three wire flexible cord kit
may be used, and the same ratings apply
as described above.
• When using a cord rated 40 Amps, remove
the next to outermost knockout (1-3/8″
diameter) in the connection plate. Likewise,
when using a cord rated 50 Amps, remove
the outermost knockout (1-3/4″ diameter)
in the plate.
• Terminations shall be either closed loop
terminals or open-end spade lugs with
upturned ends. You must use a clamp or
strain relief to hold the cord.
ELECTRICAL REQUIREMENTS
CAUTION: For personal safety,
do not use an extension cord with this
appliance. Remove house fuse or open
circuit breaker before beginning installation.
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as specified on the rating
plate. The rating plate is located above the
storage drawer on the oven frame.
We recommend you have the electrical wiring
and hookup of your range connected by a
qualified electrician. After installation, have
the electrician show you where your main
range disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to
wire your oven according to governing codes
could result in a hazardous condition. If there
are no local codes, your range must be wired
and fused to meet the requirements of the
National Electrical Code, ANSI/NFPA No. 70—
Latest Edition. You can get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new construction
(not existing) utilize a 4-conductor connection
to an electric range.
When installing an electric range in new
construction, follow Steps 3 and 5 for 4-wire
connection.
You must use a 3-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system.
If the electrical service provided does not
meet the above specifications, have a
licensed electrician install an approved outlet.
Fig. 12A Fig. 12B
Page 7
7
Installation Instructions
7
POWER CORD AND STRAIN
RELIEF INSTALLATION
• For power cord installations only (see the
next step if using conduit), assemble the
strain relief in the hole. Insert the power
cord through the strain relief and tighten.
Allow enough slack to easily attach the cord
terminals to the terminal block. If tabs are
present at the end of the winged strain
relief, they can be removed for better fit.
NOTE: Do not install the power cord
without a strain relief. The strain relief
bracket should be installed before
reinstalling the rear range wiring cover.
Skip to applicable power cord installation.
1
Power cord
Strain relief
Terminal
block
Bracket
CONDUIT AND SQUEEZE
CONNECTOR INSTALLATION
• For conduit installations only, purchase a
squeeze connector matching the diameter
of your conduit and assemble it in the hole.
Insert the conduit through the squeeze
connector and tighten. Allow enough slack
to easily attach the wires to the terminal
block.
NOTE: Do not install the conduit without a
squeeze connector. The squeeze connector
should be installed before reinstalling the
rear range wiring cover.
Skip to applicable conduit installation.
2
Squeeze
connector
Terminal
block
Conduit
Bracket
Fig. 13
Fig. 14
Page 8
8
Installation Instructions
8
ELECTRICAL CONNECTIONS (CONT.)
4-WIRE POWER CORD
INSTALLATION
WARNING: The neutral wire of
the supply circuit must be connected to
the neutral terminal located in the lower
center of the terminal block. The power
leads must be connected to the lower
left and the lower right terminals of the
terminal block. The 4th grounding lead
must be connected to the frame of the
range with the ground plate and the
ground screw.
Remove the 3 lower terminal screws from
the terminal block. Remove the ground
screw and ground plate and retain them.
Cut and discard the ground strap.
DO NOT DISCARD ANY SCREWS.
Insert the one ground screw into the
power cord ground wire terminal ring,
through the ground plate and into the
frame of the range.
Insert the 3 terminal screws (removed
earlier) through each power cord terminal
ring and into the lower terminals of the
terminal block. Be certain that the center
wire (white/neutral) is connected to the
center lower position of the terminal block.
Tighten screws securely into the terminal
block.
Re-intall the junction block access cover
making sure that wires do not become
pinched between wire cover and
mainback.
E
D
C
B
A
4
3-WIRE POWER CORD
INSTALLATION
WARNING: The neutral or
ground wire of the power cord must be
connected to the neutral terminal located
in the center of the terminal block. The
power leads must be connected to the
lower left and the lower right terminals
of the terminal block.
Remove the 3 lower terminal screws from
the terminal block. Insert the 3 terminal
screws through each power cord terminal
ring and into the lower terminals of the
terminal block. Be certain that the center
wire (white/neutral) is connected to the
center lower position of the terminal block.
Tighten screws securely into the terminal
block.
DO NOT remove the ground strap
connection.
Re-install the junction block access cover
making sure that wires do not become
pinched between wire cover and
mainback.
B
A
3
Ground
strap
Terminal
block
(appearance
may vary)
Neutral
terminal
Power cord
Before
After
Terminal
block
Terminal
block
Neutral
terminal
Neutral terminal
Ground strap
Ground
plate
(grounding
to range)
Ground
screw
Ground strap
Ground
plate
or
Fig. 15
Fig. 16a
Fig. 16b
Page 9
9
Installation Instructions
9
3-WIRE CONDUIT INSTALLATION
Loosen the 3 lower terminal screws from
the terminal block. Insert the center bare
wire (white/neutral) tip through the bottom
center terminal block opening. On certain
models, the wire will need to be inserted
through the ground strap opening and
then into the bottom center block opening.
Insert the two side bare wire tips into the
lower left and the lower right terminal
block openings. Tighten the screws until
the wire is firmly secured (35 to 50 inchlbs.). Do not overtighten the screws since
it could damage the wires.
NOTE: ALUMINUM WIRING:
Aluminum building wire may be used but
it must be rated for the correct amperage
and voltage to make connection. Connect
wires according to this step for 3-wire
conduit or the next step for 4-wire conduit.
Wire used, location and enclosure
of splices, etc., must conform to good
wiring practices and local codes.
Re-install the junction block acces cover
making sure that wires do not become
pinched between wire cover and
mainback.
B
A
5
4-WIRE CONDUIT INSTALLATION
Loosen the three lower terminal screws
from the terminal block. Remove the
ground screw and ground plate and retain
them. Cut and discard the ground strap.
DO NOT DISCARD ANY SCREWS.
Insert the ground bare wire tip between
the range frame and the ground plate
(removed earlier) and secure it in place
with the ground screw (removed earlier).
Insert the bare wire (white/neutral) tip
through the bottom center of the terminal
block opening. Insert the two side bare
wire tips into the lower left and the lower
right terminal block openings. Tighten the
screws until the wire is firmly secured (35
to 50 inch-lbs.) Do not overtighten the
screws since it could damage the wires.
Wire used, location and enclosure
of splices, etc., must conform to good
wiring practices and local codes.
Re-install the junction block access cover
making sure that wires do not become
pinched between wire cover and
mainback.
C
B
A
6
Before
Terminal
block
Ground strap
After
Terminal
block
Ground
plate
(grounding
to range)
Bracket
Neutral
terminal
Wire tips
Wire tips
Terminal
block
Conduit
Bracket
Ground
screw
Ground strap
or
Fig. 17
Fig. 18a
Fig. 18b
Page 10
10
Installation Instructions
INSTALL THE RANGE
REMOVE OVEN DOOR
Before installing the range, you may remove
the oven door to lessen the weight of the
unit. DO NOT lift unit by door handle.
To remove oven door:
Open the door to the stop position.
See Fig. 19A.
Grasp the door at each side and lift up
and off the hinges. See Fig. 19B.
CAUTION:
When the door
is removed and hinge arms are
at stop position, do not bump or
try to move the hinge arms. The
hinges could snap back causing an injury to
the hands or damage to the porcelain on the
front of the oven. Cover the hinges with
toweling or insert empty towel rolls behind
the hinges while working in the oven area.
B
A
1
LEVEL THE RANGE
For proper cooking and baking the range
must be leveled. Do not place range in cutout
until you are sure that the flanges below the
sides of the cooktop are above the top of the
counter. Lift cooktop to see flanges. Damage
to the cooktop could result if adjusted
improperly.
Install the oven racks (see use and care
section for instructions).
Use a 1-3/8″ open end wrench or an
adjustable wrench to equally back out
the four leg levelers until the flanges
(rims) below the sides of the maintop are
above the top of the counter. Check by
measuring the height of the counter and
comparing it with the measurement from
the floor to the flanges below the sides of
the cooktop. Place range in cutout when
adjustments are complete.
Put a spirit level or a glass measuring cup
partially filled with water on one of the
oven racks. See Fig. 21.
Use the wrench to adjust the leg levelers.
Level range front to back and side to side.
See Fig. 20.
D
C
B
A
2
Fig. 19B
Fig. 20
Fig. 21
Fig. 19A
Stop Position
Hinge
Lower Range
Raise
Range
Spirit Level
Leg Leveler
Page 11
11
Installation Instructions
IMPORTANT INSTALLATION
INSTRUCTIONS FOR RANGES
USED WITH COUNTERTOP
HEIGHTS UP TO 38″
The height of the range must be adjusted to
the countertop height. For countertop heights
greater than 37″, additional measurements
may need to be taken as detailed below.
When the range is elevated to the maximum
height, there is a large space between the
bottom of the range and the floor, referred
to as the toe space. This may be visually
objectionable. The legs should not be extended
any further than to provide a maximum of 3″
toe space. See Fig. 22.
The range is designed to provide a minimum
of 1″ air gap at the bottom of the range. See
Fig. 23. (Example: When legs are screwed all
the way into the base rail.)
This gap is very important to the proper
ventilation of the range and must be
maintained when treating the appearance
of the toe space.
The following is a suggested method of making
a filler for the toe space when the legs are
extended as mentioned before.
After the range is installed with the longer legs
and is in position and level, measure from the
bottom of the bodyside to the floor. This will
be the required height of the toe space filler.
See Fig. 22. This height may range from 2-1/16″
to 3″. Any height less than 2-1/16″ may not be
visually objectionable and not need the filler.
Build the filler as shown in Fig. 24. Make sure
to provide the 3/4″ gap at the top and the 5/16″
gap at the bottom. These gaps will provide the
proper ventilation as mentioned before.
If you wish to attach the filler to the floor
or adjacent cabinets, use screws or other
removable fasteners, so that the range can
be readily removed if necessary.
3
Fig. 22
3” Max. Height
Fig. 23
Fig. 24
1” Min. Height
Gusset Corners with
3/4” to 1” Triangular
or Square Stock
Use 1/4” to 1/2”
Material Finished
to Match Toe Area
of Cabinets
2-1/16” to 3” as
Required or as
Required to Recess
Behind Toe Area of
Adjacent Cabinets
6”
5/16”
3/4”
30”
Page 12
12
Notes
Printed in the United States
Loading...