GE Room Air Conditioner Use and Care Manual
ModelNumber
SerialNumber
Conarol=
I
Dateof Purchase
Opera~~ng ~ms~rue~~oms
‘OR COOLIINGORHEATING
. If cooling is required, position the SelectorSwitch to HIGH
COOL.
/f heating is required, position the SelectorSwitch to i--lIGH
HEAT.
, Set the TEMPERATURE control to the
(us:~aliythe mid-point is a good starting position), a warmer indoor air temperature),
Position tl~e AIR OUT CONTROL to CLOSED position.
desir=d number
With the controlsset asdescribed,you will receivecoolingor
heating from your General .EIectricAir Conditioner. If th~
room temperature is not satisfactoryafter a reasoilableperiod
of time, adjust the temperature control to a higher numbei
(for a cooler indoor air temperature) or a lower number (foi
,,
,
.
. .
FOR auiETER OPERATION
Follow steps 2 and 3 under NORMAL COOLING OR HEATING.
Then position the Selector Control to Low Cool or Low Heat.
This will permit cooling or heatingoperation at a lower and quieter
fan speed.
EXTREME TEMPERATURE OPERATION
Remember, for highest economy and best performance, you
always use high speed for extremely hot days.
VENTILATION
With the controls set for either cooling, heating or fan operation
only, room air can be exhausted to the outside by positioning the
Al R OUT control in the OPEN position. This can be helpful in
removing stale air, smoke or odors from the room . . . and permits
outdoor air to enter through openings normal to house con-
struction.
NOTE: Cooling effectiveness is reduced when the Al R OUT
CONTROL is OPEN, so it is suggested it not be left OPEN for
long periods, particularly on hot, humid days.
AIR C1RCULATION
For air circulation and filtering without cooling, select either
FAN Hi, or FAN LOW position on the MASTER CONTROL.
ADJUST A! R DIRECTION
TO
The grille hastwo ways of adjusting airdirection.The Vertical air
direction is adjusted by positioning the louvers up or down. The
Vertical air adjustments allow you to discharge all air upward,
or, all air downward, or, all air discharged straight ahead, or,any
combination between the positions mentioned.
The Horizontal adjustment isdone with three tabs, The three tabs
allowsyou to dischargeall air to the right, or, all air to the left, o
some air to the right and the remainder to the left, or, all air
straight ahead, or, ‘any combination between the positions men”
tioned.
With adjustment of both the Vertical and Horizontal louvers, al
can be dischargedin any desirable pattern.
HORIZONTAL
TAB
/\\
VERTICAL
TAB
Care and
MaFngemamce
TURN AIR CONDITIONEROFF AND REMOVE PLUG FROM RECEPTACLE
TO CLEAN FILTER
The filter shouId be washed at least every 30 days or asoften as
required. The inlet baffle of the front grille must be removed to
gain access to the air filter. Grasp the upper portion of the inlet
baffle and pull out !he inlet baffle. The nameplate showing the
Model and Serial numbers can be seen at this time. To remove
the foam filter from the grille frame, lift filter from the four (4)
tabs on grille frame.
NOTE: Your air conditioner should not be operated without a
filter. Replacement filters can be obtained from your local
Customer Care Service, Parts Department found in the Yellow
Pages.
Vacuum filter on the dusty side or wash with running water.
Run water from the cleaner side of the filter to drive out the
accumulated dust and lint. Shake to dry. To replace air filter,
replace filter on the four (4) tabs on grille frame. Replace inlet
baffle.
CLEANING THE AIR CONDITIONER
Front grille may be wiped with a cloth dampened in a mild
detergent solution.
or detergent and lukewarm water, then polished with the
Cabinet may be washed with mild soap
—
General Electric Liquid Wax for Appliances. To assure continued peak efficiency, condenser coils (weather side of unit)
should be checked periodically and cleaned if clog’ged with
soot or dirt from the atmosphere. Consu!t your GE service
outlet for its recommendation of the method and frequency
with which this service should be performed in your locality.
Loading...