GE PZS22MSKKHSS, PZS22MSKGHSS, PZS22MSKEHSS, PZS22MSKBHSS, PZS22MMKGHES Owner’s Manual

...

GEAppliances.com

-(3

B m

c/b

-(3

B m

c/b

Safety Instructions ............ 2-4

Operating Instructions

Automatic Ice maker ........... 15, 16

Care and Cleaning ............. 18, 19

ClimateKeeper2 _M.................... 6

Crispers and Pans .................. 14

CustomCool _M..................... 7, 9

Ice and Water Dispenser ....... 17-18

Quick Ice........................... 17

Refrigerator Doors ................. 13

Replacing the Light Bulbs ........... 20

Set Features ........................ 6

Shelves and Bins ............... 11, 12

Temperature Controls ............... 5

TurboCool _M. ........................ 6

Water Filter ........................ 10

Installation Instructions

Installing the Refrigerator ....... 30-33

Moving the Refrigerator ........ 26-29

Preparing to Install

the Refrigerator .................... 25

Trim Kits and Panels ............ 21-24

Water Line Installation ......... 34-36

Models 22, 23, 25, 26, 27 and 29

Profile COte a COte

La section frangaise commence a la page 47

Profile Lado a Lado

Refrigeradores

La seccion en espahol empieza en la pagina 93

L..

Troubleshooting Tips ...... 38-40

Normal Operating Sounds .......... 37

Consumer Support

Performance Data Sheets ...... 43, 44

Warranty (U.S.)..................... 42

Write the model and serial numbers

here: Model//

Serial//

Find these numbers on a label inside

the refrigerator compartment at the top on the right side,

200DSO74P052 49-60647-4 70- 74 GE

IMPORTANT SAFETYINFORMATION. READALL INSTRUCTIONSBEFOREUSING.

GEAppliances webs/te

For more information on your refrigerator's operation, visit www, GEAppliances.com or

call 800, GECARES {800, 432,2737), In Canada visit GEApplMnces.ca or ca//800,567,3344,

REFRIGERATOR SAFETY INFORMATION

_This is the safety alert symbol, This symbol alerts you to potential hazards that can kill or hurt you and others, All safety _nessages will follow the safety alert symbol and the word "DANGER", "WARNING", or "CAUTION", These words are defined as:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury,

Indicates a hazardous situation which, if not avoided, could result in death or serious injury,

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury,

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, explosion, electric shock, or injury when using your refrigerator follow these basic safety precautions:

This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is used, Unplug the refrigerator before making repairs, replacing a light

bulb, or cleaning, Note: Power to the refrigerator cannot be disconnected by any setting on the control panel, Note: Repairs must be performed by a qualified service professional,

Replace all parts and panels before operating, Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance,

Because of potential safety hazards under certain conditions,

we strongly recommend against the use of an extension cord,

However, if you must use an extension cord, it is absolutely

necessary that it be a UL-listed (inthe United States) or a CSAcertified (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum)

and 120 volts, To prevent suffocation and entrapment hazards to children,

remove the fresh food and freezer doors from any refrigerator

before disposing of it or discontinuing its use,

Do not allow children to climb, stand or hang on the door

handles or the shelves in the refrigerator, They could seriously

injure themselves,

IMPORTANT SAFETY INSTRUCTIONS

I__ o reduce the risk of injury when using your refrigerator, follow these basic

Do not clean glass shelves or covers with warm water when they are cold, Glass shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping or dropping, Tempered glass is designed to shatter into many small pieces if it breaks,

Keep fingers out of the "pinch point" areas: clearances between the doors and between the doors and cabinet are

necessarily small, Be careful closing doors when children are in the area,

Always clean the CustomCoofMTray after thawing food,

safety precautions,

Do not touch the cold surfaces in the freezer compartment when hands are damp or wet, skin may stick to these extremely cold surfaces,

Do not refreeze frozen foods which have thawed completely, In refrigerators with automatic icemakers, avoid contact with

the moving paRRsof the ejector mechanism, or with the heating element that releases the cubes, Do not place fingers or hands on the automatic ice making mechanism while the refrigerator

is plugged in,

INSTALLATION

_ Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

result in fire, explosion, or death.

CONNECTING ELECTRICITY

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet Do not remove the ground prong

IDonot use an adapter

lFailure to follow these instructions can result in death, fire, or electrical shock.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

GEAppliances.com

Failure to do so can

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the

possibility of electric shock hazard from this appliance, Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded,

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall

outlet, Do not use an adapter, The refrigerator should always be plugged into its own

individual electrical outlet which has a voltage rating

that matches the rating plate,

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded electrical supply is required, This provides the best

performance and also prevents overloading house wiring circuits which could cause a fire hazard from

overheated wires,

Never unplug your refrigerator by pulling on the power

cord, Always grip plug firmly and pull straight out from the outlet,

Repair or replace immediately all power cords that

have become frayed or otherwise damaged, Do not use a cord that shows cracks or abrasion damage

along its length or at either end, When moving the refrigerator away from the wall, be

careful not to roll over or damage the power cord,

PROPERDISPOSAL OF YOUR OLD REFRIGERATOR

Suffocation and child entrapment hazard. Remove fresh-food and freezer doors from the refrigerator, prior to disposal. in child entrapment which can lead to death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past, Junked or abandoned refrigerators are still dangerous even if they will sit for ':just a few

days," Ifyou are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents,

Before You Throw Away Your Old Refrigerator or Freezer:

Take off the fresh food and freezer doors, Leave the shelves in place so that children may

not easily climb inside,

Refrigerants

All refrigeration products contain refrigerants, which under federal law must be removed prior

to product disposal, If you are getting rid of an old

refrigeration product, check with the company handling the disposal about what to do,

Failure to do so can result

READANDFOLLOWTHISSAFETYINFORMAT/ONCAREFULLX

SAVETHESEINSTRUCTIONS

About the temperature controls.

Not all features are on all models. Your controls may be similar to the following."

Temperature

Touch-LED Dispenser Control

NOTE."Therefrigerator is-shippedwith

protective film covering the temperature

controls,/fthLs film was not removed during installation, remove it now

Thetemperature controls arepreset in the factory at 37°F(3°C)for the refrigerator compartment and O°F(-18°C)for the freezercompartment Allow 24 hours for the temperature to stabilizeto the preset

recommended settings, Refrigerator temperatures can be adjustedbetween 34°Fand 46_F

(7°Cto 8°C),and the freezer temperatures can beadjusted between -6°F and +8°F(-27 °Cto -73°C),

To change the Refrigerator temperature:

Tactile-LED Dispenser Control

Thetemperature controls can display both the SETtemperature as well asthe actual temperature in the refrigerator and freezer,The actual temperature may vary slightly from the SETtemperature based on usage and operating environment,

On some models, setting both controls to the warmest setting until the display flashes (off)will stop cooling in both the freezer and refrigerator compartments,

On other models, setting either control to the warmest setting

untilthe display flashes (off)will stop the cooling to the freezer and

refrigerator,

NOTE:Turningthe refrigerator off via the controls on the touch paneldoes not shut off electrical power to the refrigerator,

NOTE:The refrigerator isshipped with protective film covering the temperature controls, Ifthis film was not removed during installation,

remove it now,

Touch-LED Dispenser Control." To change the temperature, press and release the FREEZER

TEMP/FR/DGE TEMPpad, The 5ETlight will come on and

the display will show the set temperature, To change the temperature, tap either the A. or V pad until the desired

temperature is displayed,

_ecommended 0o F Recommended 37 ° F iI

m ActuelTemp Set Temp i

,L?t

Tactile LED Dispenser Control.

Once the desired temperature has been set, the temperature display will return to the actual refrigerator and freezer

temperatures after 5 seconds, Several adjustments may be required, Each time you adjust the controls, allow 24 hours for

the refrigerator to reach the temperature you have set,

Thetemperature controls can display both the SETtemperature as well

as the actual temperature in the refrigerator and freezer, Theactual

temperature may vary slightly from the SETtemperature based on usage and operating environment

Turning the cooling system off." Tactile-LED Dispenser Control

On some models, setting both controls to the warmest setting until the display flashes (off)will stop cooling in both the freezer and refrigerator compartments,

On other models, setting either control to the warmest setting

untilthe display flashes (off)will stop the cooling to the freezer and

refrigerator,

NOTE:Turningthe refrigerator off via the controls on the touch panel doesnot shut off electrical power to the refrigerator,

Touch-LED Dispenser Control:

Press and release the FREEZER TEMP/FRIDGE TEMP pad, Press Ato set freezer temperature to ._The display will

show OFF To turn the unit back on, press the FREEZER

TEMP/FR/DGE TEMPpad, Press A to set the freezer and

refrigerator temperatures to the preset points of 0°F (-18°C) for the freezer and 37°F (3°C) for the refrigerator,

When the unit is turned back on, it will take up to 24 hours to stabilize,

Performance Air Flow S stem

The Performance Air-Flow System is designed to maximize temperature control in the refrigerator and freezer

compartments, This unique special feature consists of the Air Tower along the back wall of the refrigerator and the Air

Tunnel on the bottom portion of the freezer Fearwall, Placing food in front of the louvers on these components will not affect

performance, Although the Air Tower and the Air Tunnel can be removed, doing so will affect temperature performance,

(For removal instructions, on-line, contact us at ge,com or call 800,GE,CARES,In Canada, contact us at geappliances,ca or call

1,800,561,3344,)

About Set Features. GEAppliances.com

This pad is used to select the following features:

Filte_

About TurboCool. TM

How it Works

TurboCool '_rapidly cools the refrigerator compartment in order to more quickly cool foods, Use TurboCooV when adding a large amount of food to the refrigerator compartment, putting away foods after they have been sitting out at room temperature or when putting away warm leftovers, It can also

be used if the refrigerator has been without power for an extended period,

Once activated, the compressor will turn on immediately and the fans will cycle on and off at high speed as needed for eight hours, The compressor will continue to run until the refrigerator compartment cools to approximately 34°F (1°C),then it will cycle on and off to maintain this setting, After 8 hours, or if TurboCool 'Mis pressed again, the refrigerator compartment will return to the original setting,

Now to Use

PressTurboCooC, The TurboCool temperature display will show Tc and the LEDwill be activated,

After TurboCooV' iscorn plete, the TurboCooV indicator light will go out,

TurboCool, Quick Ice, Door Alarm and Water

Tactile LED Dispenser Control:

Pressing SETFEATURESrepeatedly will cycle

through all of the available features and then

exit the mode, If no key is pressed, the mode

will exit and return to displaying features

currently set,

NOTES:The refrigerator temperature cannot be

changedduring TurboCooV,

Thefreezer temperature is not affected

during TurboCooV',

When opening the refrigerator door during TurboCooV, the fans will continue to run if

they have cycled on,

Touch-LED Dispenser Controls:

Press SET FEATURES, The refrigerator

temperature display will show TurboCooV

and/or TC, Press ON/OFF,

After TurboCool _ is complete, the refrigerator

compartment will return to the original setting,

NOTES:

Therefrigerator temperature cannot be changed

during TurboCooV,

The#eezer temperature is not affe.cted during

TurboCool ,M,

When opening the refrigerator door during

TurboCool _, the f_?nswill continue to run if they

have cycled on,

About ClimateKeeper2. TM (onsomemodds)

How it Works

The ClimateKeeper2 TMis the industry's most advanced refrigeration system, delivering

optimum temperature and humidity performance to keep food garden fresh longer

and reduce freezer burn, The ClimateKeeper2 _ system features two

evoporotors--one for the refrigerotor ond one for the freezer,

This provides two separate cooling systems, and separates the airflow between the fresh

food and freezer compartments during normal cooling operations,*

This ensures that the humidity levels in the fresh food compartment are significantly higher

than in a conventional system,** allowing fresh produce and other unsealed foods to retain

their moisture content and freshness longer, Moisture sensitive foods such as fresh fruit,

salads, rice, etc,, can now be stored on open shelves without excessive moisture loss,

Due to the higher humidity in the refrigerator,

you may on occasion experience fog or

small amounts of moisture in the refrigerator compartment, This is normal and may

come and go as different food loads and environmental conditions change, Wipe dry

with a paper towel if desired, The separate airflow system minimizes the

mixing of air between the two compartments,

which reduces fresh food odor transfer to

improve the taste of ice,

The ClimateKeeper2 _system also reduces the number of defrosting cycles in the freezer

evaporator, thereby reducing freezer burn,

*Freezer air is used in the CustomCool feature, **Testing shows a higher level of humidity in

the Fresh Food section in ClimateKeeper2 _ refrigerators versus conventional units,

About CustomCoo[ M(onsomemodds}

How it Works

Touch LED Dispenser Control

Express Thaw M

The CustornCooF'feature is used to quickly chill items, thaw items or hold the pan at a specific temperature, This feature is a system of dampers, a fan, a temperature thermistor and

a heater,

How to Use

O Empty the pan, Place the Chill/Thaw tray in

the pan, Place the items on the tray and close the pan completely,

Touch LED Dispenser Control."

Select the Express Thaw "_,ExpressChilF or Se/ectTemp "Mpad, The display and SET light will come on, Tap the pad until the light appears next to the desired setting,

Use the following chart to determine the best setting to use,

ExpressChi//can be set to 15, 30 or 45 minutes, The default is 15 minutes,

To stop a feature before it is finished: tap that feature's pad until no options are selected and the display is off,

The pan istightly sealed to prevent temperature fluctuations in the rest of the refrigerator, The controls for this pan are located on the dispenser with the temperature controls,

During ExpressThaw and ExpressChi//,the display on the controls will count down the time in the cycle (on some models),

After the ExpressThaw cycle is complete, the pan will reset to the MEATsetting (32°F

[O°C])to help preserve thawed items until they are used,

The displayed actual temperature of the

CustomCoo/pan may Vary slightly from the SETtemperature based on usage and operating environment,

NOTE."For food safety reason_ it is recommended that foods be wrapped in plastic

wrap when using ExpressThaw, This will help contain men,tjuices and improve thawing performance,

ExpressChi# "_

About ExpressChillY(on somemodels) GEAppliances.com

ExpressChil/

• SET

How it Works

ExpressChill TM

The ExpressChilFfeature is a system of dampers, a fan and a temperature thermistor,

The pan istightly sealed to prevent the pan's temperature from causing temperature

fluctuations in the rest of the refrigerator,

How to Use

Empty the pan, Place the Chill tray in the pan, Place the items on the tray and close

the pan completely, Select the ExpressChi/I TMpad, On some

models, you can then select the chill time

(use chart to determine best setting), Other models will only have one option (45

minutes), On models with multiple settings, tap the pad until the light appears next to the desired setting,

The controls for this pan are located in the top of the refrigerator or on the dispenser with the

temperature controls,

, To stop a feature before it isfinished, tap

that feature's pad until no options are selected and the display is off,

, During ExpressChill,the display on the

controls will count down the time in the cycle,

How to Remove and Replace the Drawer

Toremove: 0 Lock all four swing locks by rotating them

Pullthe drawer out to the stop position, to the lock position, Rotate all four swing locks to the unlock

position, Lift the front of the drawer up and out,

Toreplace:

Make sure all four swing locks are inthe unlock position,

Place the sides of the drawer into the drawer supports, making sure the swing

locks fit on the drawer slots,

About CustomCoo[ M(onsomemodds}

CustomCool TM Chart

NOTE: Resu/ts may vary depending on packaging, starting temperature and other food traits,

Express Tha w TM ExpressChiff _

0.5 Lb. (4 hours) 15 Minutes

Hamburger Patties (0,5 Ib) 1 Beverage Can (12 oz) Individually Wrapped 2 Small Juice Boxes (6-8 oz each)

Filet Mignon (0,5 Ib) 30 Minutes

1.0 Lb. (6 hours) 2to 6 Beverage Cans (12 oz each)

Chicken Breasts (1,0 Ib) 2 Plastic 20 oz Bottles of Beverage Ground Beef (1,0 Ib) 4 to 6 Small Juice Boxes

Steak (1,0 Ib) (6-8 oz each)

2.0 Lbs. (10 hours) 3 Foil Juice Packets

Chicken Breasts (2,0 Ibs) Wine (750 ml bottle) Ground Beef (2,0 Ibs) 45 Minutes

Steak (2,0 Ibs) 2 Liter of Beverage

3.0 Lbs. (12 hours) 1/2 Gallon of Juice

Chicken Breasts (3,0 Ibs) Gelatin-1 package Ground Beef (3,0 Ibs)

Steak (3,0 Ibs)

Se/ect Temp TM

Citrus Settinq (43°F [6°0])

Oranges, Lemons, Limes, Pineapple, Cantaloupe

Beans, Cucumbers, Tomatoes, Peppers, Eggplant, Squash

Produce Settinq (35°F [2°0])

Strawberries, Raspberries, Kiwifruit,

Pears, Cherries, Blackberries, Grapes, Plums, Nectarines, Apples

Asparagus, Broccoli, Corn,

Mushrooms, Spinach, Cauliflower, Kale, Green Onion, Beets, Onions

Meat Settinq (32°F [O°C])

Raw Meat, Fish and Poultry

About the water filter. (onsomemodels) GEAppliances.com

Water Filter Cartridge

The water filter cartridge is located in the back upper right corner of the refrigerator compartment,

caitr d

When to Replace the Filter on Models With a

Replacement Indicator Light

There is a replacement indicator light for the water filter cartridge on the dispenser, This light will turn orange to tell you

that you need to replace the filter soon, The filter cartridge should be replaced when the replacement

indicator light turns red or if the flow of water to the dispenser or ice maker decreases,

When to Replace the Filter on Models Without a

Replacement Indicator Light

The filter cartridge should be replaced every six months or earlier if the flow of water to the water dispenser or ice maker

decreases,

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one by slowly turning it to the left, Do not pull down on the cartridge, A

small amount of water may drip down,

Installing the Filter Cartridge

O Ifyou are replacing a SmartWater cartridge with an

adapter, it must be removed before installing the cartridge,

To remove the adapter, turn it to the left about 1/4 turn,

If you are replacing a Water by Culligan cartridge, leave the adapter in place, This adapter will stay in the refrigerator when

you replace future cartridges,

Holder lj

Run water from the dispenser 1-1/2 gallons (about three

minutes) to clear the system and prevent sputtering, Press and hold the WATERFILTERpad (on some models)on

the dispenser for 3 seconds,

Reset

Hold 3Sec

NOTE.'A newly-installed water filter cartridge may cause water

to spurt from the dispenser upon first use,

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter cartridge is not available, The dispenser and the ice maker will

not operate without the filter or filter bypass plug,

Byp;SS J

P!ug

smartvvate_' Water by Culligan

Some models

With adapter

(appearance may vary)

O On models without a replacement indicator light, apply the

month and year sticker to the new cartridge to remind you

to replace the filter in six months.

Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after

installation,

Line up the arrow on the cartridge and the cartridge holder, Place the top of the new cartridge up inside the holder, Do

not push it up into the holder, Slowly turn it to the right until the filter cartridge stops,

DO NOT OVERTIGHTEN. Asyou turn the cartridge, it will

automatically raise itself into position, The cartridge will move about 1/2 turn,

Without adapter

i ii

use this type of

water filter,

To use the filter bypass plug on Water by Culligan models, you must first remove the filter adapter from the cartridge holder by turning it to the left,

For the maximum benefit of your filtration system, GE recommends the use of GE branded SmartWater filters only, Using GE branded filters in GEand Hotpoint refrigerators provides optimal performance and reliability, GE branded SmartWater filters are always the right choice because they are patented and designed specifically for GE products, GE SmartWater filters meet rigorous industry NSF standards for safety and quality that are important for products that are filtering your water, GE has not qualified non-GE branded filters for use in GE and Hotpoint refrigerators and there is no

assurance that non-GE branded filters meet GE's standards for quality, performance and reliability,

If you hove questions-visit our Website at GEApplL_nces,com, or call 1,800,GE,CARES(1,800,432,2737),

Replacement #Tters:

To order additional filter cartridges in the United States, visit our Website at GEAppliances.com, or call GE Parts and

Accessories, 800,626,2002,

See filter label for type of filter to order (MWF or MSWF), Customers in Canada should consult the yellow pages for the

nearest Mabe Service Center,

About the shelves and bins.

Not all features are on a// models.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Bins

The larger refrigerator door bins and freezer tilt-out door bins are adjustable,

Toremove: Lift the front of the bin straight up,

then lift up and out,

Refrigerator bin

J J

Toreplace or relocate." Engage the back side

of the bin in the molded supports on the door,

Then push down on the front of the bin, Bin will

lock in place,

Top Freezer Bins

DO not block NOTE:

Be careful when placing items in

the top bin, Make sure that items

do not block or #_11into the ice

chute,

Freezer d/t-out bin

Press tab and pull shelf fbrwf_rd

tO f efYlO Ve

The snuggerhelps prevent tipping, spilling or

sliding of small items stored on the door shelf, Place a finger on either side of the snugger

near the rear and move it back and forth

to fit your needs,

Slide- Out Spillproof Shelf

The slide-out spillproof shelf allows you to

reach items stored behind others, The special edges are designed to help prevent spills from

dripping to lower shelves,

Toremove:

Slide the shelf out until it reaches the stop,

then press down on the tab and slide the shelf

straight out,

Top freezer bin

NOTE." Part must be in

Do not block

place as shown for proper ke

dispensing, Food cannot be stored

xll

in this location,

!_!!i

Top freezer bin (on some rnodelg

Toreplace or relocate:

Line the shelf up with the supports and slide

it into place, The shelf can be repositioned

when the door is at 90 ° or more, To reposition

the shelf, slide the shelf past the stops and

angle downward, Slide shelf down to the

desired position, line up with the supports and

slide into place,

Make sure you push the shelves a// the way

back in before you close the door,

QuickSpace "_Sheff

This shelf splits in half and slides under itself for

storage of tall items on the shelf below,

This shelf can be removed and replaced or

relocatedjust like Slide-Out Spillproof Shelves,

On some models, this shelf cannot be used in

the lowest position,

Not a# features are on all models.

Freezer Baskets

GEAppliances.com

Toremove, push the basket all the way to the

back of the freezer, Lift up until the back pins are disengaged, Lift the entire basket up and

pull out,

Slide-Out Freezer Shelves

Toremove, slide out to the stop position, lift the

front past the stop position and slide out,

Fixed Freezer Shelves

There are two types of fixed freezer shelves,

Toremove this type of shelf."

0 Lift the shelf up at the left side,

0 Bring the shelf out,

Toremove this type of shelf."

Lift up the left side of the shelf and slide it left into the center of the shelf supports,

Make sure you push the baskets all the way back in before you close the door,

Make sure you push the shelves all the way back in before you close the door,

NOTE FOR DISPENSERMODELS."In order to take full advantage of the tilt-out ice bin, only

store items on the shelf below the ice bin that

are no taller than the Iowest point on the bin,

Rotate the right side of the shelf up and out of the shelf supports,

Door Wine/Beverage Rack (on some models)

This rack holds up to 5 cans or one bottle of wine,

The rack hangs from the sides of the dairy bin,

Toremove:

Empty the wine/beverage rack,

Holding the bottom of the dairy bin, lift the front straight up, then lift up and out,

To detach the rack from the dairy bin, pull the rack's side wires out of the holes on

each side of the dairy bin,

Toreplace:

Reattach the rack to the sidesof the bin,

Engage the back side of the bin in the

molded supports on the door, Then push

down on the front of the bin, The bin will lock into place,

erator doors.

Refrigerator Doors

When the door is only partially open,

it will automatic_Uly close. Beyond this stop the door win stay

open.

The refrigerator doors may feel different than the ones you are used to, The special door

opening/closing feature makes sure the doors close all the way and are securely sealed,

When opening and closing the door, you will

notice a step position, If the door is opened past this stop point, the door will remain open

to allow you to load and unload food more

easily, When the door is only partially open, it

will automatically close,

The resistance you feel at the step position will

be reduced as the door is loaded with food,

Door Alignment

If doors are uneven, adjust the refrigerator door,

Using a 7/16" wrench, turn the door

adjusting screw to the right to raise the door, to the left to lower it, (A nylon plug,

imbedded in the threads of the pin, prevents the pin from turning unless a

wrench is used,)

O After one or two turns of the wrench,

open and close the refrigerator door and check the alignment at the top of the

doors,

About the crispers and pans. GEAppliances.com

Not all features are on a// mode/s,

Fruit and Vegetable Crispers

Excess water that may accumulate in

the bottom of the drawers should be wiped dry,

On some models, the bottom drawer has

full extension slides that allow full access to the drawer,

HI _ LO

2_ "

Adjustable Humidity Crispers

Slide the control all the way to the/-//setting to provide high humidity recommended for most

vegetables,

Convertible Dell Pan

The convertible deli pan has its own cold

air duct to allow a stream of cold air from

the freezer compartment or fresh food

compartment to flow to the pan,

The variable temperature control regulates

the air flow from the Climate Keeper Air Tower,

About crisper removal.

Not all features are on all models.

Slide the control all the way to the/0 setting to provide lower humidity levels

recommended for most fruits,

Set the control to the coldestsetting to store fresh meats,

Set the control to co/dto convert the pan to normal refrigerator temperature and provide

extra vegetable storage space, The cold air duct is turned off, Variable settings

between these extremes can be selected,

Crisper Removal

Crispers can easily be removed by pulling the drawer straight out and lifting the drawer up

and over the stop location,

If the door prevents you from taking out the drawers, first try to remove the door bins,

If this does not offer enough clearance, the refrigerator will need to be rolled forward

until the door opens enough to slide the drawers out, In some cases, when you roll the

refrigerator out, you will need to move the refrigerator to the left or right as you roll it out,

About the automatic ice maker.

A newly installed refrigerator may take 72 to 24 hours to begin making ice.

Automatic Ice maker

The ice maker will produce seven cubes per cycle- approximately 100-130 cubes in a 24-hour period, depending

on freezer compartment temperature, room temperature, number of door openings and other use conditions.

If the refrigerator is operated before the water connection is made to the ice maker, set the power switch in the OFFposition.

When the refrigerator has been connected to the water supply, set the power switch to the ONposition.

The ice maker will fill with water when it cools to 15°F (-10°C). A newly installed refrigerator may take 12 to 24 hours to begin

making ice cubes. You will hear a buzzing sound each time the ice maker fills with

water. Throw away the first few batches of ice to allow the water line

to clear. Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the ice maker will stop producing ice. It is normal for several cubes to bejoined

together. If ice is not used frequently, old ice cubes will become cloudy,

taste stale and shrv

Avoid contact with the moving parts of

the ejector mechanism, or with the heating element (located on the bottom of the ice maker) that releases the cubes.

Do not place fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in.

Special note about dispenser models:

....Some models have a tilt-out ice bin. The bin can be tilted out

as shown in the illustrations, and it will hold itself up while you

take ice out or turn the ice maker power switch on and off. Be

sure to put the bin back in place before closing the door.

....To restore your ice level from an empty bucket stage, the

following steps are recommended:

O 12 hours afiLerthe first batch of ice has fallen into the bin,

dispense 3 to 4 cubes.

O After an additional 6 hours, dispense 3 to 4 cubes again. These steps will restore your ice level in the shortest amount of

lime

ce maker Switch

Power/" / Green

Switch Feeler Arm

(on some models)

Power

Power Light Feeler Arm

(on some models)

ce maker

NOTE:

In homes with lower than average water pressure, you may hear the ice maker cycle multiple times when making

one batch of ice.

About the automatic ice maker. (cent) GEAppliances.com

Accessing Ice and Reaching the Power Switch on

Dispenser Models Models with a sheff above the ice bin

There are two types of ice storage bins on dispenser models.

One has a shelf above the bin, the other does not,

These models have a tilt-out ice bin, The bin can be tilted

Special note for models with tilt-out ice bin:

out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on and off, Be sure to put the bin back in place before

closing the door,

NO TE: /n order to take full advantage of the tilt-out ice bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

To access ice, pull the bin fbrward.

-:-- :--szz ......

To reach the power switch, pull the shelf strzdght out. Always be sure to replace the shelf

Models with tilt out ice bin

Toaccess ice and reach the icemaker power switch:

bin,

O Lift the then it fbrwz_rd

until the bin stops.

pull

O ower the bin to access ice or

reach the power switch.

Removing Ice Bin (dis/_ns_rmedals)

_ Theice bin is heavy when full,

Set the power switch to the OFF position before removing the bin,

When replacing the bin, be sure to press it firmly into place, If it does not go all the way back, remove it and rotate the drive mechanism 1/4 turn, Then push the bin back again,

On some models, to access ice or reach the power switch:

O u// the bin fbrwz_rd until the

bin stops.

Rotate

Drive

O ower the bin to access ice or

reach the power switch.

Dispenser Models only

About the ice and water dispenser. ¢onsomemodds)

To Use the Dispenser

Spill Shelf

2.;,,._

Select CUBED, CRUSHEDor WATEl?. Pressthe glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining, To reduce water spotting, the shelf and its grille should be

cleaned regularly, If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system, Press the dispenser arm for at least two minutes to remove trapped air from the water line and to fill the water system, To flush out impurities in the water line, throw away the first six glassfuls of water,

Never put fingers or any other

objects into the ice crusher discharge opening,

Locking the Dispenser

Pressthe LOCKor LOCKCONTROLSpad for 3 seconds to lock the dispenser and control panel,

To unlock, press and hold the pad again for 3

seconds,

Door Alarm

Use DoorAlarm to sound if either door is open for more than 3 minutes. The alarm will stop once the door isclosed. For LCD models, a popup screen will appear, The alarm can be silenced by touching the LCDscreen,

Touch LED Dispenser Control:

Press the SETFEA TURESpad once and DOOR ALARMwill blink, Press ON/OFFand the door

alarm will be set and the icon will turn solid, Press

ON/OFFagain to turn the alarm off,

DoorAlarm (onTactileLEDDispenserControl

model)

Toset the alarm, press this pad until the indicator light comes on, This alarm will sound if either door is open for more than 3 minutes, The light goes out and the beeping stops when you close

the door,

Dispenser Light

The LIGHTpad turns the light in the dispenser

on and off. The light also comes on when the dispenser cradle is pressed. For models with a bulb, if the light burns out, it should be replaced

with a 6 watt 12V maximum bulb. For LED

models contact Factory Service.

Quick Ice

Whenyou needto speedup ice production,usethe

QuickIce feature,While thisfeature is turned on,

the freezerfan runs continuously for 48 hours,or untilthe feature isturned OFF,Duringthisperiod, ice productionwill increaseup to 40%,Modelswith the integrated icefeature system require at FIRSTUSEat least half an 8oz, glassof iceto be dispensedevery6 to 12 hours,Thiswill helpthe ice makerfillthe bucket properly sothat dispensing isbetter,

How to Use

Touch LEDDispenser Control:

Pressthe SETFEATURESpad twice and QUICKICE

will blink. PressON/OFFto turn the feature on,then again to turn it off,

Quick Ice (on Tactile LED Dispenser Control model)

When you need ice in a hurry, press this pad to speed up ice production, This will increase

ice production for the following 48 hours or until you press the pad again,

Precise Fill (on some modds)

This water dispenser isequipped with a feature

called "precise fill," Thisfeature allows you to choose a preciseamount of water (cups or ounces)that

you would like dispensed,Pintsand Liters are also

available for LCDmodels,

Touch LED Dispenser Control

O Pressthe PRECISEFILLCUP$/OZpad, The

WATERpad will light and the CRUSHEDand CUBEDice pads will turn off, Thelast unit used

will be displayed,

O Pressthe PRECISEFILLpad again to toggle

between cups and ounces,

Ifyou selected OUNCES,pressthe A orX/ padto selectthe number of ounces you would liketo have

dispensed between 2-99 ounces,The default is 8 ounces,

GEAppliances.com

Ifyou selected CUPS,press the A or V pad to

select the amount you would liketo havedispensed, Theyare displayed as 1/4, 1/3, 1/2, 2/3 and 3/4, with

the highest amount being 16 3/4 cups, The default is 1cup,

Pressthe cup against the cradle andwater will

begindispensing, Itwill automatically stop when the amount set has beendispensed, Thedisplay will show the amount of water dispensed,beep,

then resetafter 5 seconds,

NOTE"Do not leavethe dispenser unattended when water isbeing dispensed,

Ifyou would liketo stop dispensing water

before the specified amount has been dispensed,just remove the cup Fromthe cradle, Thedisplay will show the amount that has been dispensed for 5 seconds, Ifthe cup switch is pressed again within that time, the dispenser will continue up to the setamount, If not, the display will return to the set amount,

Important Facts About Your Dispenser

Do not add ice from trays or bags to the storage drawer, It may not crush or dispense well,

Avoid overfilling glass with ice and use of narrow glasses, Backed-up ice can jam

the chute or cause the door in the chute to freeze shut, If ice is blocking the chute,

poke it through with a wooden spoon, Beverages and foods should not be

quick-chilled in the ice storage drawer, Cans, bottles or food packages in the storage drawer may cause the ice maker or auger to jam,

To keep dispensed ice from missing the glass, put the glass close to, but not touching, the dispenser opening,

Some crushed ice may be dispensed even though you selected CUBED, This happens occasionally when a few cubes accidentally get directed to the crusher,

After crushed ice is dispensed, some water may drip from the chute,

Sometimes a small mound of snow will

form on the door in the ice chute, This

condition is normal and usually occurs

when you have dispensed crushed ice

repeatedly, The snow will eventually eva porate,

Care and cleaning of the refrigerator.

Cleaning the Outside

The dispenser drip area, beneath the grille,

il i

i i i i i i i i i i

Dispenser drip area.

should be wiped dry, Water left in this area may leave deposits, Remove the deposits by

adding undiluted vinegar to the well, Soak until the deposits disappear or become loose

enough to rinse away,

The dispenser cradle. Before cleaning, lock

the dispenser by pressing and holding the LOCKor LOCK CONTROLS pad for 3 seconds,

Clean with warm water and baking soda solution-(]bout (]t(]blespoon (15 ml) of

baking soda to a quart (1 liter) of water, Rinse thoroughly and wipe dry,

The door handles and trim. Clean with a

cloth dampened with soapy water, Dry with a soft cloth,

The stainless steel doors and door handles

(on some models) can be cleaned with a commercially available stainless steel

cleaner, Cleaners with oxalic acid such as Bar Keepers Friend Soft Cleanser TM will

remove rust, tarnish and small blemishes,

Use only a liquid cleanser free of grit and

rub in the direction of the brush lines with a damp soft sponge,

Do not use appliance wax or polish on the stainless steel,

Keep the outside clean. Wipe with a clean cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent, Dry and polish with a clean, soft cloth,

Do not wipe the refrigerator with a soiled dish cloth or wet towel, These may leave

a residue that can erode the paint, Do not use scouring pads, powdered cleaners,

bleach or cleaners containing bleach because these products can scratch and

weaken the paint finish,

Cleaning the Inside

Tohelp prevent odors, leave an open box

of baking soda in the fresh food and freezer compartments.

Unplug the refrigerator before cleaning. If

this is not practical, wring excess moisture out of sponge or cloth when cleaning around

switches, lights or controls.

Use w(]rm w(]ter (]nd b(]king sod(] solution-

about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and

neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than that which is recommended, especially

those that contain petroleum distillates,

can crack or damage the interior of the refrigerator.

shelves or covers with warm water

Do not clean glass

when they are cold. Glass shelves and covers may break if exposed to sudden temperature changes or impact such as

bumping or dropping. Tempered glass is

designed to shatter into many small pieces

if it breaks. Do not wash any plastic refrigerator parts

in the dishwasher.

The chill/thaw tray is dishwasher safe,

Behind the Refrigerator

GEAppliances.com

Be careful when moving the refrigerator away

from the wall, All types of floor coverings can

be damaged, particularly cushioned coverings and those with embossed surfaces,

Pull the refrigerator straight out and return it

to position by pushing it straight in, Moving the

refrigerator in a side direction may result in damage to the floor covering or refrigerator,

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigerator, Clean the interior

with a baking soda solution of one tablespoon

(15 ml) of baking soda to one quart (1 liter) of

water, Leave the doors open,

Set the ice maker power switch to the 0 (oft) position and shut off the water supply to the

refrigerator,

Preparing to Move

Secure all loose items such as shelves and drawers by taping them securely in place to

prevent damage,

When pushing the refrigerawr back, make

sure you don It rofl over the power cord or ice maker supply line,

If the temperature can drop below freezing, have a qualified servicer drain the water supply system to prevent serious property damage

due to flooding,

When using a hand truck to move the

refrigerator, do not rest the front or back of the refrigerator against the hand truck, This could

damage the refrigerator, Handle only from the sides of the refrigerator,

Be sure the refrigerator stays in an upright

position during moving,

Replacing the light buibs.¢onsom rnod ,'s

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a

live wire filament, (A burned-out light bulb may break when being replaced,) Turning the control to the OFF position does not remove power to the light circuit,

Your fight shield will look like

one of the following; 0

oR 0

Refrigerator Compartment--Upper Light

Unplug the refrigerator,

The bulbs are located at the top of the compartment, inside the light shield, On some

models, a screw at the front of the light shield will have to be removed, On other models, the

screw is located in the pocket located at the back of the light shield,

To remove the light shield, on some models, press in on the tabs on the sides of the shield and slide forward and out, On other models,

just slide the shield forward and out,

Refrigerator Compartment--Lower Light

This fight is located above the top drawer,

Unplug the refrigerator,

0 Remove the convertible meat drawer

control knob by pulling straight out,

0 Lift the light shield up and pull it out,

O After replacing the bulb with an appliance

bulb of the same or lower wattage, replace

the light shield and screws (on some models), When replacing the light shield, make sure

that the tabs at the back of the shield fit into the slots at the back of the light shield

housing, Plug the refrigerator back in,

_t After replacing the bulb with an appliance

bulb of the same or lower wattage, replace

the shield and the knob,

Plug the refrigerator back in,

........................-ii

Freezer Compartment

Unplug the refrigerator,

Remove the shelf just above the light shield,

(The shelf will be easier to remove if it is emptied first,) On some models, a screw at the top of the light shield will need to be

removed,

To remove the light shield, press in on the sides, and lift up and out,

O Replace the bulb with an appliance bulb

of the same or lower wattage, and

reinstall the light shield, When reinstalling the light shield, make sure

the top tabs snap securely into place,

Replace the screw (on some models),

Reinstall the shelf and plug the refrigerator back in,

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a

live wire filament, (A burned-out light bulb may break when being replaced,) Turning the control to the OFF position does not remove power to the light circuit,

Dispenser (on some models) 0 Unplug the refrigerator,

The bulb is located on the dispenser under the control panel, Remove the light bulb by

turning it counterclockwise,

Refrigerator Compartment (on models with LED lighting)

Some models may have LEDlighting display If this assembly needs to be replaced, call GE on the top and/or sides of the fresh food Service at 1,800,432,2737 in the United States

compartment and in the rear and side of the or 1,800,561,3344 in Canada,

freezer compartment

GEAppliances.com

Replace the bulb with a bulb of the same size and wattage,

Plug the refrigerator back in,

I r I I Display

Trim kits and decorator panels.

For CustomSty/e _"models

Read these instructions completely and carefully.

Before You Begin

Some models are equipped with trim kits that a//ow you to install door panels. You can order pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories, 800.626.2002, or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4" (6 mm) thick

When installing wood panels less than 1/4" (6 ram) thick, you need to create a filler panel, such as 1/8" cardboard, that will fit between the face of the door and the wood panel, Ifyou are installing the pre-cut decorator panels, pre-cut filler panels are included

in the kit, The combined thickness of the decorator or wood panel and the filler panel should be 1/4" (6 mm),

Panels 1/4" thick or less

(

1/4" max

3/4" (19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4" (6 mm) thick backing, or a 3/4" (19 mm) routed board can be used, The raised portion of the panel must be fabricated to permit clearances of at least 2" (5,1 cm) from the handle side for fingertip clearance,

Panels thicker than 1/4" (6 mm), up to 3/4" (19 mm) max, will require that the outer 5/16" (8 mm) of panel perimeter be no thicker than 1/4" (6 mm),

Weight limitations for custom panels;

Fresh Food 38 Ibs, (17 kg) max, Freezer Door 28 Ibs, (73 kg) max,

Panels thicker than 1/4" (6 mm)

5/16" (8 m m)

1/4" (6 mm) max

3/4" (19 m m)

2" (5.1 cm) Clearance

Handle Side

Panel

1/4" (6 mm) Thick Backing

3/4" (19 mm)

Refrigerator Door

Trim kits and decorator panels. GEAppliancescom

23'Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels,

Freezer Panel Freezer Panel

Without Dispenser With Dispenser

Fresh Food Panel

Cutout---_ I"_--1/8" (3 mm)

.... J

5/16"

(8 mm)

Cutout

5/16"

(8 mm)

I_--1/8" (3 mm)

i i

177/8''

(45,4 cm)

67%/

(170,9 cm)

FRONT

141_Z'

(36,8 cm)

25' CustomStyld _Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels,

FRONT 14_%/' .,

(36,8 cm)

33_8"

(85,4 cm)

1/8" (3 mm)---_l

67%/'

(170,9 cm)

FRONT

,,.. 19_%/' .__._

(49,5 cm)

-_- Cutout

m m

--J 5/16"

"-] (sram)

Freezer Panel

Without Dispenser

Cutout

5/16"

(8 m m)

_-- 1/8" (3 mm)

i i

69"

(175,3 cm)

FRONT

141YZ'

'(36,8 cm)

Cutout

Freezer Panel

With Dispenser

5/16"

(8 mm)

F_--1/8" (3 mm)

i i

I 7"

(43,2 cm)

FRONT

36X"

(92,0 cm)

Fresh Food Panel

1/8"(3 mm)---_I _- Cutout

' --_5/16"

-L--

"] (sram)

69"

(175,3 cm)

FRONT

__ 191_£" ._._

(49,5 cm)

Inserting the door panels.

Read these instructions completely and carefully.

Insert the Freezer Panel and Fresh Food Panel.

Carefully push the freezer panel in until it slides into the slot behind the door handle, Push the filler

panel (required with some door panels)in behind the decorator panel, Repeat for fresh food panel,

Insert the Bottom Freezer Panel (on dispenser models).

Carefully push the panel in until it slides into the slot behind the door handle, Push the filler panel (required

with some door panels) in behind the decorator panel,

0 Attach the Top Trim on the Freezer and Fresh Food Doors.

The Top Trim can be found inside the refrigerator Hand tighten only, Make sure that the top of each panel compartment, fits snugly behind the lip of the Top Trim,

With a T-20 Torxdriver, attach the Top Trim, using two screws on each Top Trim piece, to the top of each door,

Ifyour model has a dispenser, this step only applies to

the fresh food panel and top freezer panel,

Side Trim

Cut-Out

Panel

Fresh Food Panel

Panel

Side Trim

Instafl the Side Trim.

These pieces are tucked inside the refrigerator door handle,

Do not remove the protective film on the outside of the

Side Trim until the Side Trim is installed, Fit the bottom of the Side Trim under the Bottom Trim as

illustrated,

GEAppliances.com

Hold the Side Trim against the front face of the decorator panels and fit the Side Trim under the Top Trim, Make sure

the magnetically attached Side Trim is fitted correctly and that you are satisfied with the appearance of all the parts,

Bottom Tri_

Installation

efrigerator

Instructions

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.561.3344 or Visit our Website at: geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Savetheseinstructions

for local inspector's use.

" IMPORTANT - Observe all governing

codes and ordinances,

• Note to Installer- Be sure to leave these instructions with the Consumer,

• Note to Consumer - Keep these instructions for future reference.

• Skill level - Installation of this appliance requires basic mechanical skills.

• Completion time - Refrigerator Installation

30 minutes Water Line Installation

30 minutes

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

If the refrigerator has already been installed, remove the base grille (see Step 2 in Moving

the Refrigerator, then skip to Step 5 in Installing the Refrigerator.

Models 22, 23, 25, 26, 27 and 29

PREPARATION

WATER SUPPLY TO THE ICE MAKER

If the refrigerator has an ice maker, it will have to be connected to a cold water line. AGE water

supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at ge.com (in Canada at geappliances.ca) or from Parts and Accessories,

800.626.2002 (in Canada 1.888.261.3055).

TOOLS YOU WILL NEED

3/8" and 5/1 6" Socket

1/8" HexWrench

1/2" and 7/16" Wrench

Plastic Putty Knife

Phillips Head Screwdriver

Installation Instructions

MOVING THE REFRIGERATOR

FT1LOADING THE REFRIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors until

the refrigerator is in its final location. To move the refrigerator, use a padded hand

truck. Center the refrigerator on the hand truck and secure the strap around the refrigerator.

DO NOT OVERTIGHTEN THE STRAP.

If the refrigerator must go through

any entrance that is less than 38---wide, the doors must be removed. Proceed

to Step 3.

DO NOT remove the handles. If all entrances (Ire more than 38_<wide,

skip to/nstalling the Refrigerator.

[] DISCONNECT THE WATER COUPLING

(on some models)

If the refrigerator has a water dispenser, there is a water line from the cabinet into

the bottom hinge on the freezer door that must be disconnected.

To disconnect, push in on the white collar of the coupling and pull out the tubing.

White collar

F21REMOVE THE BASE GRILLE

Remove the grille by removing the two Phillips

head screws.

Bottom

freezer

hinge

Installation Instructions

MOVING THE REFRIGERATOR(CONT,)

DISCONNECT THE POWER COUPLING

(on some models}

If the refrigerator has a water dispenser,

there is a power line (harness) from the cabinet into the bottom hinge on the freezer door that

must be disconnected. To disconnect, pull apart at the coupling.

Botror'n _ _ L_I _' \_J

fr.eezer / T" ___

h_n

B] DISCONNECT THE ELECTRICAL

CONNECTORS (on some models}

If the refrigerator has a refreshment center,

there are electrical connectors (harnesses) from the cabinet into the bottom hinge

on the refrigerator door that must be disconnected.

To disconnect, pull apart each connector.

r61CLOSE THE FREEZER AND

REFRIGERATOR DOORS

ITI REMOVE THE FREEZERDOOR

[_[] Remove the freezer door top hinge cover

(if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

Remove the two 5/16" or 1/8" hex head screws,

[]

then lift the hinge straight up to free the hinge pin.

5/16" or 1/8" hex head

Bottom refrigerator

hinge

r_ Open the freezer

door to 90.°

1 J

i ,

90°

Installation Instructions

[1] REMOVE THE FREEZER DOOR (cont.)

r_ As one person slowly lifts the freezer door up

and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.

90°

r_ Set the door on a non-scratching surface with

the inside up.

I_ REMOVE THE REFRIGERATOR DOOR

[] REMOVE THE REFRIGERATOR DOOR

(cont.)

r_ Remove the two 5116" or 118" hex head screws,

then lift the hinge straight up to free the hinge pin.

5/1 6" or 1/8" hex head

r_ Open the refrigerator door to 90,°

[] Remove the refrigerator door top hinge cover

(if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

90°

Installation Instructions

MOVING THE REFRIGERATOR(CENT,)

REMOVE THE REFRIGERATOR DOOR

(cont.)

Lift the refrigerator door up and off the bottom

hinge.

If the refrigerator has a refreshment center, one person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the bottom hinge.

[9-1REPLACING THE DOORS

To replace the doors, simply reverse steps 3 through 8.

However, please note the following:

• When lowering the doors onto the bottom hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.

• When connecting the water line, make sure

you insert the tubing all the way to the mark.

Refreshment Center Models Only

rE] Set the door on a non-scratching surface with

the inside up.

Mark

• Do not pinch the tubing and harnesses when placing the doors on the bottom hinges.

• When connecting the power line and the electrical lines (refreshment center models only), be sure that the connectors are seated together fully.

+ 114 hidden pages