GE PWT26SGRCKSS, PSW26SGRCKSS, PSW23PSRBKSS, PST29NHPCWW, PST29NHPCCC Owner’s Manual

...
0
vvvvvv.GEAppliances.com
Safety Instructions ........... 2-4
Operating Instructions
Automatic Icemaker ........... 14
Care and Cleaning .......... 16, 17
Crispers and Pans ............. 13
CustomCool r'*. ............... 7, 8
Ice and _A'ater Dispenser ........ 15
Refligerator Doors ............ 12
Replacing the Light Bulbs ....... 18
Shelves and Bins ........... 10, 11
Temperature Controls ........... 5
TurboCooF _ ................... 6
_A'ater Fiher . .................. 9
Installing the Refligerator . . . .98-31
Moving the Refligeramr . .... 24-27
Preparing to Install
the Refligerator . .............. 93
Trim Kits and Panels ........ 19-92
Wamr Line Installation ...... 39-34
Models23,25,26,27 and29
ProfileC6te fiC6te
Rdfrigdrateurs
La section fran_aise commence a la page 46
Profile Lado a Lado
Refrigeradores
d
Troubleshooting Tips ....... 36-38
Normal Operating Sounds ...... 35
Consumer Support
Consumer Support ..... Back Cover
Performance Data Sheet ........ 41
Product Registration ........ 43, 44
State of Calitbrnia ¼'ater
Treatment Device Certificate ..... 49
Warranty (Canadian) ........... 39
VVarrantv (U.S.) ............... 40
Write the model and serial numbers here:
Model #
Serial #
La secci6n en espa#ol empieza en /a pagina 88
Find these numbers on a label inside
the refligerator compartment at the top on the right side.
200D2600P042 49-60350 09-04Jfl
IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner's Manual.
SAFETYPRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
This refi_igerator must be properly installed and located in accordance with the Installation
Instructions before it is used.
Do not allow children to climb, st;rod or hang on the shelves in the reti_igerato_: They could
damage the refrigerator and seriously iqjm'e themselves.
Do not touch the cold sm_i_ces in the fl'eezer compartment when hands are damp or wet. Skin
may stick to these extremely cold sudaces.
Do not store or use gasoline or other flammable \:q)o_s and liquids in the vicinity ot this or any other appliance.
In refl_igerato_ with automatic icemake_,
avoid contact with the moving parts of the ejector mechanism, or with the heating element
located on the bottom oI the icemake_; Do not place finge_ or hands on the automatic
icemaking mechanism while the refl]gerator is plugged in.
Keep finget_ out ot the "pinch point" areas; clearances between the doo_ and between
the doo_ and cabinet are necessarily small. Be caretul closing doo_ when children are
in the area.
Unplug the refl_igerator before cleaning and
making repai_.
NOTE."We stronglyrecommendthatanyservicingbe performedby aqualified individual
Setting either or both controls to 0 (off) does not remove power to the light circuit.
Do not refl'eeze frozen foods which have thawed completel>
_ Mwa_:s clean the CustomCooY_Tray after thawing
fi_od.
DANGER!RISKOFCHILDENTRAPMENT
PROPERDISPOSALOFTHEREFRIGERATOR
GEAppliances.com
Child entrapment and suffocation are not i)rol)lems of the past.Junked or abandoned refl_igeratm_ are
still dangerotls.. ,even if they will sit for "just a few days." If you are getting rid of yore" old refrigerator,
please follow the instructions below to help prevent accidents.
Before YouThrowAway YourOldRefrigerator
Refrigerants
M1 refl_igeration prodtu'ts contnin refl'igerants, which trader federal law must be removed prior
to product disposal. If wm are getting rid of an old refrigeration product, check with the
company handling the disposal about what
1() do.
or Freezer:
Take off the dome.
I,eave the shelxes in place so that children ma) not easilx climb inside.
USEOFEXTENSIONCORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.
However; ifxou must use an extension cord, it is absolutely necessary that it be a Ui,-listed (in the United States) or a (;SA-listed (in Canada), B-wire grotmding type appliance extension cord haxing a grotmding
type i)lug and outlet and that the electrical rating of the cord be 15 amperes (minimmn) and 12(1 xolts.
3
IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.
WARNING!
HOWTOCONNECTELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For
personal safety this appfiance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (gromMing) plug which mates with a stnndard 3-prong (gromMing) wall outlet
to minimize the possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualNed electridan to make sure the outlet is
propedy gromMed.
If the outlet is a standard 2-prong outlet, it is gmr personal responsibility and obligation to have it
replaced with a propedy grotmded %prong wall outlet.
The refl-igerator, should always, beI_lugged,, into its own indixidual electrical outlet which has a xoltage rating that matches the rating plate.
This provides the best pedimnance and also I_rexents oxerloading, house wiring circuits which
could cause a fire hazard fl'om oxerheated wires.
Never tmi_lug your, refl'igerator, bx, I)tilling, on the I)°wer cord. Mwavs,, II,gli _ )lug firefly, and pull straight
out fl'om the outlet.
Repair or replace immediately all power cords that have become fl'ayed or otherwise damaged. Do not
use a cord that sho_:s cracks or abrasion damage along its length or at either end.
When moving the refl'igerator away from the wall, be carefld not to roll over or damage the power cord.
USEOFADAPTERPLUGS(Ad_pterplug_notpermittedinco_odo)
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.
However; if'you, must use an adapter; where local codes pemfit, a temporary connection may be made
to a proi)erly grotmded 2-prong wall outlet by use of a UI Aisted adapter a\:lilable at most local
1/[I I'(1W[lI'e stores.
The linger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper
polarity in the com_ection of the power cord.
When disconnecting the power cord ti'om the
adapte_; alwa_:s hold the adal)ter in place with one hand while pulling the power cord i)lug with the other hand. If this is not done, the adapter gromM
temfinal is very likely to break with repeated use.
If the adapter grotmd temfinal breaLs, DO NOT
USEthe refrigerator tmtil a proper grotmd has
been established.
Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the
cover screw is metal, and not ihsu/ated, and the waft outlet is grounded through the house wiring. Youshould
have the circuit checked by a qualified electric&n to make sure the outlet is properly grounded
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCTIONS
4
Aboutthe temperaturecontrols. GEAppliances.com
The temperature controls are preset in the factory at 37°1:for the
refrigerator compartment and O°Ffor the freezer compartment. Allow
24 hours for the temperature to stabilize to the preset recommended
settings.
The temperature controls can display both the SET temperature
as well as the actual temperature in the refrigerator and freezer.
The actual temperature may vary slightly from the SETtemperature
based on usage and operating environment. Setting either or both controls to OFFstops cooling in both the freezer
and refrigerator compartments, but does not shut off electrical power to the refrigerator.
j-
temperature controls. If this film was not removed during installation, remove it now.
NOTE: The refrigerator is shipped with protective film covering the
Tochange the temperature, press and release the WARMER or COLDERpad. Tile SETlight will come
on and tile display will show tile set temI)eratm'e. To change tile temperatm'e, tap either tile
WARMER or COLDERpad until tile desired
temperatm'e is displayed. Refl'igerator temperatm'es can be ac!justed between 34°F and 44°F and tile
fl'eezer temperatm'es can be ac!iusted between
-6°F and +6°E
Once tile desired temperature has been set, tile temperatm'e display will retm'n to tile actual
refl-igerator and fl'eezer temperatm'es after 5 seconds. Several ac!iusnnents may be required.
Each time you a(!itlSt controls, allow 24 hotli's t0I" tile refl-igerator to reach tile temperatm'e you have set.
Toturn thecooling system off,tap tile WARMER pad
for either tile refl-igerator or tile fl'eezer tmtil tile display shows OFF. To turn the unit back on, press tile
COLDERpad fin" either tile refrigerator or fl'eeze_:
The SETlight will illuminate on the side w)u selected. Then press the COLDERpad again (on the
side where the SErlight is illuminated) and it will go to tile preset points of O°Ftor tile fl'eezer and
37°ElOr tile refl-igerato_: Setting either or both controls to OFFstops cooling in both the fl'eezer
and refrigerator compartments, but does not shut off electrical power to tile refl-igerato_:
PerformanceAk FlowSystem
Tile Perl0mmnce M>Flow System is designed to maximize temperature control in tile refrigerator
and fl'eezer comparmlents. This unique special teatm'e consists _ff tile Mr Tower along tile back
wall of tile refrigerator and tile Mr Tmmel on tile
bottom portion of tile fl'eezer rear wall. Placing fi_od in fl'ont ot tile louvers on these components will not
affect pe_fommnce. Mthough tile Mr Tower and tile ?dr Tmmel can be removed, doing so will affect
temperatm'e pedomlance. (For removal instructions, on-line, 24 horn's a da> contact us at
GEAl)pliances.com or call 800.GE.CARES. In Canada, contact us at geappliances.ca or call
1.800.361.3400.)
AboutTurboCooEM
How it Works
compartment in order to more quickly cool fi)ods. Use TurboCoolwhen adding a
TurboCool
large amount of food to the refligerator compartment, putting away fi)ods after they
have been sitting out at room temperature or when putting away warn/lettove_. It can also be used if the refl_igerator has been
without power tot an extended period.
Once acti\:_md, the compressor will turn oil immediately and the rims will cycle on and off at high speed as needed fiw eight hom_.
The compressor will continue to rtm tmfil the refligerator compartment cools to
approximately 34°F (l °C), then it will cycle on and off to maintain this setting. _Mter 8
hom_, or if TwboCool is pressed again, the refl_gerator compartment will return to
the original setting,
TurboCoolrapidly cools the retiigerator
How to Use
Press TurboCooLThe reflJgerator temperature display Mll show TC.
_Mter TurboCool is complete, the
refl_gerator compartment will return to the original setting,
NOTES:The refligerator temperatm'e
cmmot be changed dining
TurboCooL
The fl'eezer temperatm'e is not affected during TurboCooL
_4]_en opening the refrigerator (loot" (hmng rurboCool, the tiros
will continue to run if they have
cycled on.
AboutCustomCoolY CEApplia,ces.com
SET ExpressThaw ExpressChi/I SelectTemp
How it Works
Tile CustomCoolTM teattlre is a svsteIn of dampe_, a t,m, a temperature thermistor
and a heate_: Depending on tile flmction selected, a combination of these will be
used to quickly chill items, thaw items or hold tile pan at a specific temperatm'e.
How to Use
Tile pan is tightly sealed to prevent tile pen's temperatm'e fl'om causing tempemtm'e
fhlCttlafions in tile rest of tile reti_igeratm:
Tile controls for this pan are located at tile top of tile reti_igerator with tile temperature
controls.
ExpressThawTM
ExpressChillTM
Empty tile pan. Place tile Chill/Thaw
0
tray in tile pan. Place tile items on tile
tray and close tile pan completely. Select tile ExpressThaw: _ ExpressChilY_
@
or SelectTempTM pad. The display and
SETlight will come on. Tap tile pad until the light appeax_ next to the
desired setting, krse the chart to detemline tile best setting to use.
To stop a teatm'e before it is finished, tap that teatm'e's pad
tmfil no options are selected and
the display is off. During ExpressThaw and
ExpressChill,tile displa) on tile
controls will co/mt down tile time in tile cycle.
_dier tile ExpressThaw cycle is
colnplete, tile l)an will reset to tile MEATsetting (31°F) to hel I) preserve
thawed items tmtil they are used.
Tile displayed actual temperature (ff
tile CustomCoolpan may va U slightly
ti'om tile SETtemperatm'e based on
usage and operating enviromnent.
NOTE"Forfoodsafety reasons,it is recommended
thatfoodsbe wrappedinplastic wrap when using
ExpressThaHz Thiswill helpcontainmeatjuices andimprovethawing performance.
How to Remove and Replace the Drawer
Toremove: 0 I,ock all tour swing locks by rotating
O Pull tile drawer out to tile stop position, them to the lock i)osifion. @ Rotate all Ibm" swing locks to tile unlock
position.
O i,ift tile ti'ont (ff tile drawer up and ()tit.
Toreplace:
O Make sm'e all fore" swing locks are in tile
tmlock position.
O Place the sides of the drawer into the
drawer supports, making sure tile swing
locks fit on tile drawer slots.
AboutCustomCool:
,0
CustomCoolTM Chart
NOTE: Results may vary depending on packaging, starting temperature and other food traits.
ExpressThaw ExpressChill
0,5 Lb. (4 hours)
Hamburger Patties (0.5 lb) hMMdually X,Ympped
Filet Mignon (0.5 lb)
1.0 Lb. (6 hours)
/ Chicken Breasts (1.0 lb)
GroulM Beef (1.0/b)
[ Steak (l.0 lb)
2.0 Lbs. (10 hours)
Chicken Breasts (2.0 lbs)
Ground Beef (2.0 lbs)
Steak (2.0 lbs)
3.0 Lbs. (12 hours)
/ Chickm_ Breasts (3.0 lbs)
I/ _1, 15M
(/ _ 30Mi_J
II 41145M N
15 Minutes
1 Beverage Can (12 oz)
2 SmallJuice Boxes (6_ oz each)
30 Minutes
2 to 6 Beverage Cans (12 oz each)
I" 2 Plastic 20 oz Bottles of Beverage
iu 4 to 6 Small.Juice Boxes
(C_8 oz each)
3 Foil Juice Packets Wine (750 ml bottle)
45 Minutes
2 I,iter of Beverage 1/2 Gallon of.Juice
Gelatin-1 package
N
t cn_us
_ pR_gUCE
OM_T
SelectTemp
Citrus Setting (43°F)
Oranges,, I,em(ms, I,imes, Pineapple, Cantaloupe
Beans, (Mcumbe_, Tomatoes, Peppe_, Eggplant, Squash
Produce Setthlg 135°F)
Strawberries, Raspberries, ](dwifl'uit, Petal, Cherries, Blackberries,
Grapes, Plums, Nectarines, Apples
_sparagus, Broccoli, Corn Mushrooms, Spinach, Cauliflower, I;a_le,Green Onion, Beets, O_i()_xs
Meat Setting (31 r)
Raw Meat, Fish and P mltry
/' Ground Beef (3.0 lbs)
[ Steak (S.0 lbs)
Aboutthe water filter.(onsomemodels) GEAppliances.com
/
;artridge
MOldS[
Place flTetop of flTecartridge up inside the cartridge holder and
slowly turn it to the right.
RESETWATERFILTER
HOLD3SECS
Water Filter Cartridge
The water filter ('artrklge is located in tile
back ul/per fight corner of tile i'eflJgei'ator
coi//lln l'tIllent.
When to Replace the Filter
There is a replacement indicator light fin"
tile water filter cartridge on tile disl/ensel;
This light will turn Ol'ange to tell you that
w)u need to replace the filter soon.
Tile filter cartridge shotfld be lvl)laced
when the replacement indicator light turns red or if the flow of water to the dispenser
o1"icel/lnkel" (_lecl'e_lSeS.
Installing the Filter Cartridge
O If you are re )lacino tile cartridge, tiI_t
remox, e tile old one b) slowl) tm'ning it to tile left. Do not pull d(m'n on tile
cartridge. A small amotmt of water may drip down.
Fill tile replacement cartridge with water fi'om tile tap to alh)w for better
flow fl'om tile dispenser immediately after installation.
I.ining up tile arrow on tile cartridge
@
and tile cartridge holder; place tile top of the new cartridge up inside
tile holder; Do not push it up into the holder;
O Rtm water fl'om tile dispenser tot
3 minutes (about gallons) to clear tile s_stem and prevent sputtering.
0 Press and hold tile RESETWATERFILTER
pad on tile dispenser for 3 seconds.
NOTE" A newEqnstalled wamr filmr cartridge may cause water to spurt flom
tile dispense_:
Filter Bypass Plug
Y()u must use tile filter bypass plug when a replacement filter cartridge is not
available. Tile dispenser and tile icemaker
will not operate without tile filter or filter
byl)ass plug.
Replacement Filters:
To order additional filter cartridges
in the United States, visit our Website,
GEAppliances.cem,or call
GE Parts and Accessories, 800.626.2002.
GWF Suggested Retail $34.95 USD
Customeis in Canada should consult the yellow pages for tile nearest Camco
Service Centei:
Slowly tm'n it to tile right tmtil tile filter cartridge stops. DO NOTOVERTIGHTEN.
_S VOlt ttlFn tile cartridge, it will automatically raise itself into position.
Cartridge will retain about 1/4 turn.
Abouttheshelvesandbins.
Not all features are on all models.
Refrigerator Door Bins and Freezer Door Tilt-Out Bins
Large Bins
The larger refl-igerator door bins and freezer tilt-out door bins are ac!justable.
Toremove: Lift the ti'ont of the bin straight
up, then lift up and out.
Refrigeratorbin
j/
Freezertilt-outbin
Toreplace or relecate: Engage the back side
of the bin in the molded supports on the
(loo_: Then push down on the front of the bin. Bin will lock in place.
Small Bins
Toremove: i,ifi the fi'ont of the bin strai,,ht
up then out.
Toreplace: Position the bin abo_e the
rectangular molded supports on the doo_:
Then slide the bin down onto the support
to lock it in place.
Thesnuggerhelps prevent tipping, spilling
or sliding of small items stored on the door shelf. Place a finger on either side of the
snugger near the rear and move it back and forth to fit your needs.
Dohotblock
CAUTION:Be
carefulwhenp/aclbg itemsinthetopb/h.
Makesurethat itemsrionotblock orfailintotheice
chute.
Top freezer bin
Press tab and pull shelf forward to remove
Slide-Out Spillproof Shelf
The slide-out spillproof shelf allo_:s you to reach items stored behind othe_. The
spatial edges are designed to help prevent spills ti'om ddpping to lower shelves.
Toremove:
Slide the shelf out until it reaches the stop,
then press down on the tab and slide the shelf straight out.
Toreplace or relocate:
I,ine the shelf up with the supports and slide it into place. The shelf can be
repositioned when the door is at 90 ° or
more. To reposition the shelf, slide the shelf past the stops and angle downward. Slide
shelf down to the desired position, line up with the supports and slide into place.
Make sure you push the shelvesall the way back in before you close the door.
OuickSpace TM Sheff
This shelf splits in half and slides under itself tin" storage _fftall items on the shelf
below.
On some models, this shelf cannot be used in the lowest position.
10
This shelf can be removed and replaced
or relocatedj ust like Slide-Out Spillproof Shelves.
Not all features are on all models.
Freezer Baskets
To remove, push tile basket all tile way to tile Make sure you push the baskets all the way back
back of the ti'eezei: l,ift ii I) until the back I'i?before you close the door
)ins are disen ,a_,ed I,ifl tile entire basket
up and pull out.
GEAppliances.com
i( i;¸¸ (//j;)
Sfide-Out Freezer Shelves
To remove, slide out to the stop position,
lift tile front past tile stop position and slide out.
Fixed Freezer Shelves
There are two _,l)es of fixed
fl'eezer shel',es.
Toremovethis typeofshelf:
I,ifl the shelf up at the left side.
@ grin_ the, hell )lit,
To remove this type of shelf:
@ Rotate the right side ot the shelf up
r S "(
i,ifl up tile left side of tile shelf and slide it leit into the center of the shelf
SUl)l)orts.
and ()lit of the shelf supports.
Makesureyoupushtheshelvesall thewayback in beforeyouclosethe door
NOTE FOR DISPENSER MODELS: In (>rder
to take lull advantage of tile tilt-out ice 1)in, only store items on the shelf below the ice
bin that are no taller than the lowest point on the bin.
Door Wine/Beverage Rack (onsomemodels)
This rack holds up to 5 cans, one botde of x_ine or one 2-liter bottle of soda.
The rack hangs fl'om the sides of the dair_ bin.
To remove:
O EmpQ tile wine/bmerage rack.
Holding tile bottom of tile dairy bin, lift tile ti'ont straight up, then lift up
and o/it.
To detach tile rack from tile &fli T bin, pull the rack's side wires out of the
holes on each side of the dairy bin.
Toreplace:
Reattach tile rack to tile sides of tile bin.
Engage tile back side of tile bin in tile molded SUl)ports on tile do()):
Then push down on tile ti'ont of tile bin. The bin will lock into place.
11
Abouttherefrigeratordoors.
Refrigerator Doors
iii/i
ii
When the door is only partially open,
it will automatically close. Beyond flTisstop flTedoor will stay open.
j
Tile reti_igerator (loo_ may teel different than the ones you are used to. The special
door opening/closing teatuI'e nlakes sure tile/loo_ close all tile way and are securelv
sealed.
When opening and closing tile door you will notice a stop position. If tile door is
opened past this stop point, tile door will i'elllain open to allow VOtl to load and
/mh)ad fi)od more easily. When the door is only partially open, it will automatically
close.
Door Alignment
1t (h)o_ are tmexen, a(!iust tile retrigerator (h)o_:
LTsing a 7/16" socket wrench, turn tile
door a(!iusting screw to the right to raise tile doo_; to tile left to lower it.
(A nflon I)lug, imbedded in tile
threads _ffthe pin, prevents the pin ti'om turning unless a wrench is used.)
Tile resistance you ti_el at tile stop position will be reduced as tile door
is loaded with fi)od.
AJier one or two ttlrns of the wI'ench,
oI)en..... and close the refrigerator, door
and check the alignment at the top of
tile dooiN.
Toremovetbebase
grille,opentbe removethescrewat
eachendoftbe base grilleandthenpull
tbegrillestraightout.
7/16"SocketWrencb]
_5 % Raise
12
Aboutthe crispersandpans. GEAppliances.com
Not all features are on all models.
Fruit and Vegetable Crispers
Excess water that Inav acculnulate ill the bottom of the (h'awe_ should be wiped (h_':
On some models, the bottom drawer has
lull extension slides that allow flfll access
to the drawei:
HI _ LO
-
Adjustable Humidity Crispers
Slide the control all the way to the HIsetting to provide high hulnidi_; recolnlnended fin"
most vegetables.
Convertible Meat Pan
The comertible ineat pan has its own cold air duct to alh)w a stream of cold air from
the fl'eezer colnl)artment to flow to the pan.
i ii:i
The variable temperature control regulates
the air flow fr(nn the (_lilnate KeepeI:
Aboutcrisperremoval
Slide the control all the way to the LO .settin,,_ to proxide lower h ulnidi_' lexels
i'ecolnlnellded fi)i" most fl'uits.
Set the control to the coldest setting to store fl'esh ineats.
Set the control to coldto convert the pan to hernial refl_igerator telnl)erature and
provide extra vegetable storage space. The cold air duct is turned ofl_ ¼_riable settings
between these extrelnes can be selected.
Not all features are on all models.
Crisper Removal
Crispei_ can easily be removed by pulling
tile drawer straight out and lifting the drawer up and over the stop location.
If the door l)revents you fl'oln taking out the (h'awei_, fiI_t try to remove the door
bins. If this does not offer enough clearance, the refrigerator will need to
be rolled torward until the door opens enough to slide the drawei_ ()tit. In soine
cases, when you roll the refl'igerator ()tit,
you will need to inove the reflJgerator
to the left or right as you roll it ()tit.
13
Abouttheautomaticicemaker.
A newly installed refrigerator may take 12to 24 hours to begin making ice.
Automatic Icemaker
On dispenser models,
to access ice or reach the power switch:
o Lift thebin, then pull it
forward until the bin stops.
Lower the bin to access ice or reach the power switch.
NOTE:In order to take full advantage of the tilt-out ice bin, only store items
on the shelf below the ice bin that are no taller than the Iowest point
on the bhT.
The icemaker will produce seven cubes per cycle---aI)I)roMmately ] 00-130 cubes in a 94-hour period, depending on fl'eezer
coiill)ai'tulent teiilpei'att/i'e, i'ooiil t eil/pei'at tli'e, n tlillber ()f d()()r ()l)enings
and other use conditions.
If the reflJgerator is operated heft)re the water connection is made to the icemaket;
set the power switch in the 0 (off) position, _,_hen the refl_gerator has been connected
to the water SUl)l)l); set the power switch to the I (on) position.
The icemaker will fill with water when it cools to 15°F (-10°C). A newly installed
refi_igemtor may take 12 to 24 horns to beg4n
makhlg ice cubes.
You will hear a buzzing sotmd each time
the icemaker fills with water; Throw away the first troy 1)atches of ice to
allow the water line to clem:
Be sm'e nothing interteres with the sweep of the teeler amL
When the bin fills to the level (ff the feeler am_, the icemaker will stop producing
ice. It is nomml ti)r several cubes to be
joined together:
If ice is not used fl'equentl> old ice cubes
will become cloudy, taste stale and shrink.
Special note about dispenser models:
Dispenser models have a tilt-out ice bin.
The bin can be tilted out as shown in the illustrations, and it will hold itself up
while you take ice out or mrn the icemaker power switch on and off'. Be
sure to put the bin back in place before
closing the doo_:
To restore your ice level from an empty bucket stage, the following steps are
recommended:
O 12 hom_ alter the fi_t batch of ice
has fidlen into the bin, dispense 3 to 4 cubes.
@ _MteI"an additional 6 hom_, dispense
3 to 4 cubes again.
These steps will restore your ice level in the shortest amount of time.
Icemaker
f
Green p0werLight FeelerArm
NOTE:/n homes with lower-than-averagewater pressure,you mayhear the icemakercycle multiple
times whenmak/bg onebatchof ice.
o Lift thebin, then pull it
forward until the bin stops.
Lift andpull forward again
to remove the bin.
14
Removing Ice Bin (dispenser models) CAUTION:Theicebin is heavywhen full
Set the power switch to the 0 (Off) position before removing the bin.
Whenreplacingthebin,be stlre to press it
firefly into place. If' it does not go all the way back, remove it and rotate the drive mechanism l/4 ttlFn. Then push the bin back again.
Dispenser Models only
Aboutthe ice and water dispenser.(onsomemodels) GEAppliances.com
ToUse the Dispenser
Select CUBEDICE _J, CRUSHEDICE I_ Dispenser Light
SpillShelf
or WATER i_ .
Press the glass gentl} against the top ot tile dispenser cradle.
The si)ill shelf is not selfkh'aining. To reduce water spotting, the shelf and LIGHT
its grille should be cleaned regularly.
If no wateris dispensedwhen therefrigeratoris first installed,theremaybe airin thewaterline
system.Pressthedispenserarmforat least two Quick Ice minutesto removetrappedair fromthewater
line andtofill the watersystem.Toflushout impuritiesin thewaterline, throwawaythefirst slkglassfulsof water
CAUTION:Neverputfingersoranyother objectsinto theicecrusherdischargeopening. QUICKICE
Lockingthe Dispenser
p.dfo, sec,>,ldsto
. ,-esstheLOCKCON OL
LOCKCONTROL hold the pad again
HOLD3 SECS
lock tile dispenser and control panel. To
tmlock, press and
for 3 seconds.
DoorAlarm
Q
DOORALARM
This pad turns tile night light in tile dispenser
on and off. Tile light
also COllleS 1>11 when
tile dispenser cradle is pressed. If this light bm'ns out, it should be
replaced with a 6 watt
12V maximttm bulb.
-\,\'hen you need ice in a hinT,X; press this
pad to speed up ice production. This will
increase ice l/roducfion for the following
48 hotus or tmfil )'ou press the pad again.
To set the ;11;11111, l/l'ess this pad tmti] the
indicator light c_>mes on. This al:mn will
sound if either door is
(>lien JOE l//Ol'e thml
3 minutes. The light
goes otlt and the
beeping stops when vot/close the dool:
Important Facts About Your Dispenser
Do not add ice fi'om tra_s or bags to tile storage (h'awe_: It may not crush or
dispense well.
Avoid ovedilling glass with ice and use ot
narrow glasses. Backed-u I) ice can jam the chute or cause tile door in tile chute to
freeze shut. If ice is blocking the chute, poke it through with a wooden spoon.
Beverages and ti>ods should not be quick-chilled in the ice storage drawe_:
Cans, bottles or fi>od packages in tile
storage dI'awer Ill,IV cause tile icemaker
or a tiger to jaln.
To kee I) dispensed ice ti'om missing
the glass, put the glass close to, but not touching, the dispenser opening.
Some crushed ice may be dispensed even though you selected CUBEDICE.
This hapl)ens occasionally when a fi_w cubes acddentally get directed to
the crusher.
f_dter crushed ice is dispensed, some
water Inay drip flx>m tile chute. Sometimes a small motmd of snow will
timn on tile door in tile ice chute. This condition is nomlal and usually occms
when you have dispensed crushed ice
repeatedly. The snow will eventually evapoi'ate.
15
Careand cleaning of the refrigerator.
Cleaning the Outside
The dispenser drip area, beneath tile giille,
should be _ped dIT: _,\_ter left in this area may lea',e deposits. Remo',e the deposits by
Dispenser drip area.
adding undiluted vinegar to the well. Soak
until tile deposits disappear or become
loose enotlgh to iJnse _l_';iv.
The dispenser cradle. Before cleaning, lock
tile dispenser by pressing and holding tile LOCKCONTROLpad tot 3 seconds. Clean
with wam_ water and baking soda solution--about a tnblespoon (15 ml) of
baking soda to a quart (l liter) of wateI:
Rinse thoroughly and wipe dry.
The deer handles and trim. Clean with
a cloth dampened with soapy wateI:
Dry with a soft cloth.
The stainless steel panels and door handles
(oil sonle models) can be cleaned with a commercially a\:filable stainless steel cleanei: A spra)_on stainless steel cleaner
works best.
Do not use appliance wax or polish on the stainless steel,
Keep theoutsideclean.Wipe Mth a clean cloth lightly dampened Mth kitchen
appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.
Donot wipethe refrigeratorwith a soileddish clothor wet towel.Thesemayleavearesidue
thatcanerodethepainLDonotusescouring pads,powderedcleaners,bleachorcleaners
containingbleachbecausetheseproductscan scratchandweakenthepaintfinish.
Cleaning the Inside
Tohelp prevent odors, leave an open bc,x ,':4
baking soda in tile fl'esh ti)od and fl'eezer
COII/l)_l i'tiilents.
Unplug the refrigerator before cleaning. If this
is not practical, wiing excess moisture ()/It
of sponge or cloth when cleaning around
switches, lights or controls.
Lrse w;mn wamr and baking soda solution--
about a tablespoon (15 ml) of baking soda
to a quart (1 liter) (ff wami: This both cleans and neutralizes odois, Rinse and
wipe dry:
Useofanycleaningsolutionotherthanthat
which isrecommended,especiallythosethat
containpetroleumdistillates,cancrackor damagetheinterioroftherefrigerator.
Avoidcleaningcoldglassshelveswith hotwater becausetheextremetemperaturedifference
maycausethemtobreak.Handleglassshelves carefufigBumpingtemperedglasscancause
it to shatter Donot washanyplastic refngeratorparts
in thedishwasher
Thechili/thawtrayis dishwashersafe.
16
Behind the Refrigerator
Be careful when moving the refl_igerator away fl'om the wall. _dl types of floor
coverings can be damaged, particularly cushioned coverings and those with
enlbossed S/li]_lces.
Pull the refl_igerator straight out and return it m position by pushing it straight in.
Moving the refl_igerator in a side direction may result in damage to the floor covering
or refl_igerato_:
Preparing for Vacation
For long ;;ications or absences, YelllOve
food and uI_plug the refl_igerato_: Clean the interior with a baking soda solution of one
tablespoon (15 ml) of baking soda to one quart (l liter) of water: i,eave the (loo_
open.
Set the icemaker power switch to the 0 (off) position and shut off the water supply to
the refl_igeratm:
GEAppliances.com
When pushing the refrigerator back, make sure
you don't roll over the power cord or icemaker
supply line.
If the temperatm'e can drop below fl'eezing, have a qualified servicer drain the water
supply s)'stem to prevent serious property damage due to flooding.
Preparing to Move
Secure all loose items such as shelves and (h'awe_ by taping them securely in place
to prevent damage.
X4]_en using a hand track to move the
refl_igeratot; do not rest the fl'ont or back _ffthe reti_igerator against the hand truck.
This could damage the refrigerator. Handle only fl'om the sides of the refl_igeratm:
Be sure the refn)erator stays in an upn)ht position during moving.
17
Replacingthelightbulbs.
Setting the controls to OFFdoes not remove power to the light circuit.
Refrigerator Compartment--Upper Light
Tabs
Unplug the refl'igerator.
0
The bulbs are located at the top of the
0
compartment, inside the light shield. On some models, a screw at the fl'ont of
the light shield will have to be removed.
To remoxe the light shield, press in on
@
the tabs on the sides of the shield and slide fin'ward and out.
Refrigerator Compartment--Lower Light
Thishght is located above the top drawe_
O Unplug the refrigerator:
@ Remo'_e the comertible meat drawer
control knob b) pulling straight out.
IJtt the light shield up and pull it out.
Freezer Compartment
O ,Mter replacing the bulb with an
appliance bulb of the same or lower wattage, replace the light shield and scrmvs (on some models). When
replacing the light shield, make sure that the tabs at the back of the shield
fit into the slots at the back of the light shield housing.
O Plug the refl_igerator back in.
@ _Mter replacing the bulb xfith an
appliance bulb of the same c,r lower wattage, replace the shield and
the knob.
Plug the refrigerator back in.
[ , ,
OUn _lug the refligerator
Remoxe the shelf just aboxe the light shield. (The shelf will be easier to
remoxe if it is emptied fi_t.) On some models, a screw at the top of the light
shield will need to be remoxed.
To remoxe the light shield, press in on the sides, and litt up and out.
Dispenser
Unplug the refl_igeratox: The bulb is located on the dispenser
trader the control panel. Remove the light bulb by turning
it counterclockwise.
Replace the bull) with an appliance
O
bulb of the same or lower wattage, and reinstall the light shield. When
reinstalling the light shield, make sure the top tabs snap securely
into place. Replace the screw
(on some Inodels).
Reinstall the shelf and plug the refrigerator back in.
O Replace the bulb with a bulb of the
same size and wattage.
Plug the refrigerator back in.
18
Trimkits anddecoratorpanels.
For CustomStgM°'models
Read theseinstructions completely and carefully.
BeforeYouBegin
Some models are equipped with trim kits that aflow you to install door panels. You can order pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories,
800.626.2002,or you can add wood panels to match your kitchen cabinets.
Panels less than 1/4" (6 mm) thick
When installing wood panels less than ]/4" (6 ram) thick, you need to create a filler panel, such as ]/8"
cardboard, that Mll fit between the ti_ce of the door and the wood panel. If you are installing the pre-cut decorator panels, ix'e-cut filler panels are included in the kit. The coml)ined thickness of the decorator
or wood panel and the filler panel should be 1/4" (6 ram).
PanelsI/4" thickorless
1/4" max
3/4" (19 mm) or Raised Panel
A raised panel design screwed or glued to a 1/4" (6 ram) thick backing, or a ./4 (19 ram) routed board can be used. The raised portion of the panel must be tid)ricated to i)ennit clearances of at least _" (5. l cm)
from the handle side tot fingertip clearance.
•/4 (l 9 ram) max, xdll reqmre that the outer :)/16 (8 ram) ofPanels thicker than 1/4" (6 ram), uI) to 3 .......
panel perimeter be no thicker than 1/4" (6 ram).
Weightlimitationsfor custompanels."
FreshFood38Ibs. (17kg)max. FreezerDoor28Ibs.(13kg)max.
Panelsthickerthan1/4"(6ram)
1/4"(6ram)
k Backing
f
2"(5.1 cm) Clearance
1/4"(6ram)max
3/4"(19 ram/
HandleSide
Appearance "'" Panel
Door
19
Trimkits anddecoratorpanels.
Dimensions for Custom Wood Panels
FreezerPanel
WithoutDispenser
Cut 1/8" out -_'I I_-(3ram)
''
i i
i
5/16" (8ram}
67_S' (170.9cm)
_. 141_Z' .__
(36.8cm)
FRONT
FreezerPanel
WithDispenser
Cut 1/8" out "-_f f_-(3 ram}
''
i i
177X' (45.4cm)
FRONT
. 141_2" .--_
(36.8 cm)
33_" (85.4cm)
{
FreshFoodPanel
1/8" Cut
(3n/m)"-_f f_'- out
'' ._
' '--- 5/16"
I....1 18ram)
67%Z'
(170.9cm)
FRONT
191_2"_._..
(49.5cm)
The areas at the top of the panels need to be cut out of the panels.
2O
Insertingthe doorpanels.
Read these instructions completely and carefully.
0 Insert the Freezer Panel and FreshFood Panel
(_arefully push the ti'eezer panel in until it slides If your model has a dispense_; this step only applies into the slot behind the door handle. Push the filler to the fl'esh fi)od panel and top fl'eezer panel.
panel (required with some door panels) in behind the decorator panel. Repeat fin" fl'esh fi_od panel.
0 Insert the Bottom Freezer Panel (on dispenser models).
(_areftfll) push the panel in tmtil it slides into the (reqtfired with some door panels) in behind the slot behind the door handle. Push the filler panel decorator panel.
Attach the TopTrimon the Freezer and Fresh FoodDoors.
The Top Trim can be fi_tmd inside the reii_Jgerator each (loo_: Hand tighten only. Make sm'e that the compartment, top of each panel fits snugly behind the lip of the
_]th a T-20 Torxdrive_; attach the Top Trim, using Top Trim. two scre_:s on each Top Trim piece, to the top oI
Cut-Out
SideTrim
21
Insertingthe doorpanels.
O Install the Side Trim.
These pieces are tucked inside the reti_gerator door handle.
Donot removetheprotectivefilmon theoutsideof theSideTrimuntil the SideTrimis instated.
Fit the bottom of the Side Trim under the Bottom Trim as illustrated.
Hold the Side Trim against the fl'ont ti_ce of the decorator panels and fit the Side Trim under
the Top Trim. Make sure the magnetically attached Side TYim is fitted correctly and that _m are
satisfied with the appearance of all the parts.
22
Installation
Refrigerator
Instructions
I Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT - Savethese
instructions for local inspector's use.
IMPORTANT - Observeall
governing codes and ordinances.
Note to Installer - Be sure to leave these instructions with the Consumer.
Note to Consumer - Keep these instructions for future reference.
Skill level - Installation of this appliance requires basic mechanical skills.
Completion time - Refrigerator Installation
Proper installation is the responsibility of the installer.
In Canada, call 1.800.361.3400 or Visit our Website at: geappliances.ca
30 minutes Water Line Installation
30 minutes
Models 23, 25, 26, 27 & 29
PREPARATION WATER SUPPLY TO THE ICEMAKER
If the refrigerator has an icemaker, it will have
to be connected to a cold water line. AGE water supply kit (containing tubing, shutoff
valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at GEAppliances.com (in Canada at geappliances.ca) or from Parts and
Accessories, 800.626.2002 (in Canada
1.888.261.3055).
TOOLS YOU WILL NEED
3/8" and 5/16" Socket 1/2" and 7/16" Wrench
I
Product failure due to improper installation is not covered under the Warranty.
If the refrigerator has already been installed, remove the base grille (see Step 2 in Moving
the Refrigerator), then skip to Step 5 in
Installing the Refrigerator.
Plastic Putty Knife
Phillips Head Screwdriver
23
Installation Instructions
MOVING THE REFRIGERATOR
[] LOADING THE RERIGERATOR
ONTO A HAND TRUCK
Leave all tape and door pads on doors
until the refrigerator is in its final location. To move the refrigerator, use a padded
hand truck. Center the refrigerator on the hand truck and secure the strap around
the refrigerator. DO NOT OVERTIGHTEN
THE STRAP.
i
If the refrigerator must go through any entrance that is less than 38"
wide, the doors must be removed.
Proceed to Step 3. DO NOT remove the handles.
If all entrances are more than 38" wide, skip to Installing
the Refrigerator.
[] DISCONNECT THE WATER
COUPLING (on some models)
If the refrigerator has a water dispenser,
there is a water line from the cabinet into
the bottom hinge on the freezer door that
must be disconnected. To disconnect, push in on the white collar
of the coupling and pull out the tubing.
White collar
[] REMOVE THE BASE GRILLE
Remove the grille by removing the two Phillips head screws.
Bottom
freezer
hinge
24
Installation Instructions
[] DISCONNECT THE POWER
COUPLING (on some models)
If the refrigerator has a water dispenser,
there is a power line (harness) from the
cabinet into the bottom hinge on the freezer door that must be disconnected.
To disconnect pull apart at the coupling.
[] DISCONNECT THE ELECTRICAL
CONNECTORS (on some models)
If the refrigerator has a refreshment center, there are electrical connectors
(harnesses) from the cabinet into the
bottom hinge on the refrigerator door
that must be disconnected.
To disconnect, pull apart each connector.
[] CLOSE THE FREEZER AND
REFRIGERATOR DOORS
[] REMOVE THE FREEZER DOOR
[] Remove the freezer door top hinge cover
by either squeezing it and pulling it up or by prying it off with a plastic putty knife.
Bottom refrigerator
hinge
[] Remove the two 5/16" hex head screws,
then lift the hinge straight up to free the
hinge pin. 5/16" hex head
[] Open the freezer door to 90. °
90 °
25
Installation Instructions
MOVING THE REFRIGERATOR (CONT.)
[]
REMOVE THE
FREEZER DOOR (cont.)
[]
As one person slowly lifts the freezer door up and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.
°
90°
[] REMOVE THE
REFRIGERATOR DOOR (cont.)
[] Remove the two 5/16" hex head screws,
then lift the hinge straight up to free the
hinge pin.
[] Open the refrigerator door to 90. °
5/16" hex head
[] Set the door on a non-scratching surface
with the inside up.
[] REMOVE THE
REFRIGERATOR DOOR
[] Remove the refrigerator door top hinge
cover by either squeezing it and pulling it up or by prying it off with a plastic putty knife.
J
/
90 °
26
Installation Instructions
[] REMOVE THE
REFRIGERATOR DOOR (cont.)
[] Lift the refrigerator door up and off the
bottom hinge. If the refrigerator has a refreshment
center, one person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the bottom hinge.
[] REPLACING THE DOORS
To replace the doors, simply reverse steps 3 through 8.
However, please note the following:
* When lowering the doors onto the
bottom hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.
When connecting the water line, make sure you insert the tubing all the way
to the mark.
Refreshment Center Models Only
[] Set the door on a non-scratching surface
with the inside up.
Mark
Do not pinch the tubing and harnesses
when placing the doors on the bottom
hinges.
When connecting the power line and
the electrical lines (refreshment center
models only), be sure that the
connectors are seated together fully.
27
Installation Instructions
INSTALLING THE REFRIGERATOR
REFRIGERATOR LOCATION
Do not install the refrigerator where the temperature will go below 60°F (16°C)
because it will not run often enough to maintain proper temperatures.
Do not install the refrigerator where the temperature will go above 100°F (37°C)
because it will not perform properly.
Install it on a floor strong enough to
support it fully loaded.
CLEARANCES
Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections:
23' 25/26/27' and 29'
Sides 1/8" (4 mm) 1/8" (4 mm) Top 1" (25 mm) 1" (25 mm)
Back 1/2" (13 mm) 1" (25 mm)
DIMENSIONS AND SPECIFICATIONS
(for CustomStyle TM models)
Water Electrical
24"(61 cm)
Cabinet
/4" (19ram)Airspace
(1/2"[13ram]Gap+
1/4" [6mm]Wall Plates)
' 3L 1
25" (63.5cm) C0untert0p
28
Installation Instructions
[] CONNECTING THE REFRIGERATOR
TO THE HOUSE WATER LINE (icemaker and dispenser models)
A cold water supply is required for automatic icemaker and dispenser operation. If there is not a cold water supply, you will need to provide one. See Installing the Water Line section.
NOTES:
Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall
outlet.
If your refrigerator does not have a water filter, we recommend installing
one if your water supply has sand or particles that could clog the screen of
the refrigerator's water valve. Install it
in the water line near the refrigerator. If using GE SmartConnect TMRefrigerator
Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter.
Do not cut plastic tube to install filter.
[] If you are using copper tubing, place a
compression nut and ferrule (sleeve) onto
the end of the tubing coming from the
house cold water supply.
If you are using the GE SmartConnect TM
tubing, the nuts are already assembled to the tubing.
[] If you are using copper tubing, insert
the end of the tubing into the refrigerator
connection, at the back of the refrigerator, as far as possible. While holding the
tubing, tighten the fitting.
If you are using GE SmartConnect TM
tubing, insert the molded end of the
tubing into the refrigerator connection,
at the back of the refrigerator, and tighten
the compression nut until it is hand tight.
Then tighten one additional turn with a
wrench. Overtightening may cause leaks.
[] Fasten the tubing into the clamp provided
to hold it in position. You may need to pry
open the clamp.
Tubing Clamp 1/4" Tubing
1/4"
Compression
Ferrule
(sleeve)
Refrigerator Connection
SmartConnect TMTubing
[] TURN ON THE WATER SUPPLY
Turn the water on at the shutoff valve (house water supply) and check for
any leaks.
[] PLUG IN THE REFRIGERATOR
Before plugging in the refrigerator, make
sure the icemaker power switch is set to
the 0 (off) position.
%
29
See the grounding information attached
to the power cord.
Installation Instructions
INSTALLING THE REFRIGERATOR (CONT,)
[] PUT THE REFRIGERATOR
IN PLACE
Move the refrigerator to its final location.
[] LEVEL THE REFRIGERATOR
The refrigerator can be leveled by adjusting the rollers located near the bottom hinges.
[] LEVEL THE REFRIGERATOR
(cont.)
To adjust the rollers on 23' models:
Turn the front roller adjusting
screws clockwise
to raise the
refrigerator,
counterclockwise Roller adjusting screws
to lower it. Use a
3/8" hex socket or wrench, or an adjustable
wrench.
These models also have rear adjustable rollers so you can align the refrigerator
with your kitchen cabinets. Use a long-
handled 5/16" socket wrench to turn the screws for the rear rollers--clockwise to
raise the refrigerator, counterclockwise
to lower it.
Raise
Rollers have three purposes:
Rollers adjust so the door closes easily when opened about halfway. (Raise the
front about 5/8" [16 mm] from the floor.)
Rollers adjust so the refrigerator is firmly positioned on the floor and does
not wobble.
Rollers allow you to move the
refrigerator away from the wall for
cleaning.
To adjust the rollers on 25/26/27' and 29' models:
adjusting screws
clockwise to
Turnt eroer ILIL
raise the
to lower it. Use a
refrigerator, _[_ __
3/8" hex socket
or wrench, or an
counterclockwise ._____,_
adjustable
wrench.
Roller adjusting screw
[] LEVEL THE DOORS
Adjust the refrigerator door to make the doors even at the top.
To align:
[]
Using a 7/16" wrench, turn the door adjusting screw to the right to raise the door, to the left to lower it.
NOTE:
A nylon plug, imbedded in the threads of the pin, prevents the pin from turning
unless a wrench is used.
[]
After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.
Doors should be even at top
!
30
Loading...
+ 102 hidden pages