GE PSB9240DFWW, PSB9240DFBB, PSB9240BLTS, ZSC2200NWW, ZSC2200NBB Installation Guide
...
Installation
Instructions
Advantium®
240V Built-In
SpeedCook Ovens
PSB9240DF
PSB9240SF
PSB9240BL
ZSC2200
ZSC2201
ZSC2202
49-40690-2
MFL59060926
09-17 GEA
Español
For a Spanish version of this manual, visit
our Website at GEAppliances.com.
Para consultar una version en español
de este manual de instrucciones, visite
nuestro sitio de internet GEAppliances.
com.
GE is a trademark of the General Electric Company. Manufactured under trademark license.
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IMPORTANT — Save these
instructions for local inspector’s use.
IMPORTANT — Observe all governing
codes and ordinances.
• Note to Installer — Be sure to leave these
instructions with the Consumer.
• Note to Consumer — Keep these
instructions with your Owner’s Manual for
future reference.
• Skill Level — Installation of this appliance
requires basic mechanical and electrical skills.
• Completion Time — 1 Hour.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is
not covered under the warranty. See Owner’s
Manual for warranty information.
IMPORTANT — Use this oven only
for its intended purpose. Never use the oven
for warming or heating a room. Prolonged use
of the oven without proper ventilation can be
hazardous.
CAUTION
For personal safety, remove house fuse
or oven circuit breaker before beginning
installation to avoid severe or fatal shock injury.
CAUTION
For personal safety, the mounting surface must
be capable of supporting the cabinet load, in
addition to the added weight of the 80-pound
oven and 30-pound drawer, plus additional
oven loads of up to 50 pounds or a total weight
of up to 160 pounds.
CONTENTS
Design Information
Models Available ...............................................2
Product Dimensions and Clearances ................4
Tools and Parts Required .................................4
Parts Supplied ...................................................4
Electrical Tools and Parts Required ..................4
Advance Planning ............................................. 4
Installation Preparation
Electrical Requirements .................................... 5
Install Junction Box ...........................................5
Preparing the Opening (Installation without
an accessory storage drawer) .....................6-7
Preparing the Opening (Installation with
an accessory storage drawer) .....................8-9
Installation Instructions
Step 1, Remove Packaging and Parts ............ 10
Step 2, Route Conduit .....................................11
Step 3, Install Bottom Trim ..............................12
Step 4, Install Mounting Screws ......................12
Step 5, Finalize Installation ............................. 12
MODELS AVAILABLE
Models:
PSB9240DFWW - White
PSB9240DFBB - Black
PSB9240SFSS - Stainless Steel
PSB9240BLTS - Black Stainless Steel
Monogram Models:
ZSC2200NWW–White
ZSC2200NBB–Black
ZSC2201NSS–Stainless Steel
Monogram Pro Range Models:
ZSC2202NSS–Stainless Steel
NOTE: This unit cannot be installed with an
accessory storage drawer.
CAUTION
For personal safety this product cannot be
installed in cabinet arrangements such as an
island, a peninsula or below a countertop.
2
Información de seguridad
ANTES DE COMENZAR
Lea estas instrucciones por completo y con
detenimiento.
IMPORTANTE — Guarde estas
instrucciones para el uso de inspectores locales.
IMPORTANTE — Cumpla con todos los
códigos y ordenanzas vigentes.
• Nota al instalador — Asegúrese de dejar estas
instrucciones con el Consumidor.
• Nota al consumidor — Mantenga estas
instrucciones con el Manual del Propietario para
referencia futura.
• Nivel de capacidad — La instalación de
este aparato requiere capacidades mecánicas y
eléctricas básicas.
• Tiempo de finalización — 1 hora.
• La instalación adecuada es responsabilidad
del instalador.
• La garantía no cubre fallas producidas
por la instalación inadecuada del producto.
Consulte el Manual del propietario para
obtener información sobre la garantía.
IMPORTANTE — Utilice este horno
sólo con el objetivo para el que fue creado.
Nunca use el horno para entibiar o calentar una
habitación. El uso prolongado del horno sin una
ventilación adecuada puede resultar peligroso.
PRECAUCIÓN
Para seguridad personal, quite el fusible o el
interruptor de circuitos de la vivienda antes
de comenzar la instalación a fin de evitar una
lesión grave o fatal.
PRECAUCIÓN
Para seguridad personal, la superficie de
montaje debe poder soportar la carga del
gabinete, además de las 80 libras del horno
y las 30 libras del cajón, más las cargas
adicionales del horno de hasta 50 libras o un
peso total de hasta 160 libras.
PRECAUCIÓN
Para su seguridad personal, este producto no
puede ser instalado en arreglos de alacena,
como por ejemplo, islas, penínsulas o debajo de
superficies de trabajo.
3
Design Information
PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model.
21-1/2”
1-3/5s
1”
1-1/10s
13”
TOOLS AND PARTS REQUIRED
(NOT SUPPLIED)
• #2 Phillips screwdriver
• Hand held drill
• High speed drill bit, 3/32" diameter
• 3/8" slot head screwdriver
• Level
• Saw
• 2x4 or 2x2 lumber for installing runners
or 3/8" plywood for floor (if required)
• Wood screws or other hardware for installing
runner or shelf to support oven (if required)
• Safety glasses or goggles
PARTS SUPPLIED
• 6 brass screws (3 required, 3 extra)
• 5 color matched screws (4 required, 1 extra)
• Bottom trim
ELECTRICAL TOOLS AND PARTS
REQUIRED (NOT SUPPLIED)
• Junction box
• Electrical cable (3-conductor or 4-conductor wire
as required by local codes)
• UL-listed conduit connectors
• Wire cutters and wire strippers
29-3/4”
19”
ADVANCE PLANNING
• These ovens may be installed directly into a 30”
wide oven cabinet.
• Cutout dimensions are NOT the same for
installation with or without an accessory storage
drawer. Make sure to use the correct cutout when
preparing the opening.
NOTE: Model ZSC2202 CANNOT be installed
with an accessory storage drawer. See Installation
Preparation Without an Accessory Storage Drawer
for this model.
IMPORTANT — This oven is not
approved for use above another built-in
Advantium Speedcook oven, a side by side
installation or below a countertop.
•
For personal safety, this oven cannot be
installed in a cabinet arrangement such as an
island or peninsula.
• The oven must be installed at least 36-3/4”
above the floor.
• Allow for clearance to adjacent corners, walls,
drawers, etc.
• Cabinets installed adjacent to wall ovens
must have an adhesion spec of at least 194ºF
temperature rating.
The oven must be securely installed in a cabinet
that is firmly attached to the house structure.
Weight on the oven door could cause the oven
to tip and result in injury. Never allow anyone to
climb, sit, stand or hang on the oven door.
If installing the drawer accessory, the drawer
must be assembled to the oven prior to
installation into the cabinet. See the Accessory
Storage Drawer Assembly Instructions.
4
Installation Preparation
ELECTRICAL REQUIREMENTS
Single Speedcook Installation
Product rating is 120/208 or 120/240 volt, 60 Hz,
30 amps. This product must be connected to a
supply circuit of the proper voltage and frequency
and protected by a time delay fuse or circuit
breaker. Power should be supplied from a separate,
dedicated 30-ampere branch circuit. Wire size
must conform to the requirements of the National
Electrical Code or the prevailing local code.
Combined Speedcook and Wall Oven
Installation
When installed in combination with a GE/Monogram
single wall oven, use separate electrical junction
boxes.
Refer to single oven installation instructions for
electrical requirements of that product.
These connections must be made by a qualified
electrician. All electrical connections must meet
National Electrical Code or prevailing local codes.
Combined Speedcook and Warming Drawer
Installation
When installing the Speedcook oven over a GE
or Monogram electric warming drawer, a separate
120V, 60Hz, properly grounded receptacle must be
installed. See instructions packed with the warming
drawer.
ADVERTENCIA
• El encendido eléctrico al circuito paralelo deberá estar
apagado mientras se realizan las conexiones de línea.
• Use conductores de cobre únicamente.
• Este electrodoméstico requiere que se realice una
conexión a tierra. El extremo libre del cable verde (cable
a tierra) debe estar conectado a una conexión a tierra
adecuada. Este cable debe permanecer conectado a la
conexión a tierra del horno.
• Si la tubería de agua fría presenta interrupciones
por plásticos, juntas, conexiones de uniones u otros
materiales aislantes, NO use la misma como conexión a
tierra.
• NO se debe conectar a tierra en una tubería de
suministro de gas.
REQUISITOS ELÉCTRICOS (Cont)
• NO posee un fusible en el circuito neutro o de conexión
a tierra. Un fusible en el circuito neutro o de conexión a
tierra podría ocasionar una descarga eléctrica.
• Consulte a un electricista calificado o personal del
servicio si tiene dudas de que el electrodoméstico se
encuentre conectado a tierra apropiadamente.
Si no se siguen estas instrucciones, se podrán
producir lesiones graves o la muerte.
INSTALL JUNCTION BOX
WARNING
•
The electrical power to the oven branch circuit
must be shut off while line connections are being
made.
•
Use copper wiring only.
•
Electrical ground is required on this appliance.
The free end of the green wire (ground wire)
must be connected to a suitable ground.
This wire must remain grounded to the oven.
•
If cold water pipe is interrupted by plastic,
non-metallic gaskets, union connections or other
insulating materials, DO NOT use for grounding.
•
DO NOT ground to a gas pipe.
•
DO NOT have a fuse in the NEUTRAL or
GROUNDING circuit. A fuse in the NEUTRAL
or GROUNDING circuit could result in an
electrical shock.
•
Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
Failure to follow these instructions could result in
serious injury or death.
The conduit is located at the top right on the back of
the oven.
Locate and install the junction box within reach of
the oven conduit.
• Through the left or right sides of the cabinet
wall and into adjacent cabinet.
• Or, through the cutout floor.
• Or, in the upper cabinet.
Cutout
Height
5
Installation Preparation
Preparation WITHOUT an Accessory Storage Drawer
PREPARE THE OPENING
The Advantium 240V can be installed in
combination with other GE/Monogram
appliances. Always follow each product’s
Installation Instructions to complete the
installation.
30”
17-1/2”
36-3/4”
Min.
23-1/2”
25-1/4”
Construct
Base
Min. 3/8”
Plywood
Supported
by 2x4
or 2x2
Runners all
Four Sides
PREPARE THE OPENING (CONT.)
Installation over a GE/Monogram
Warming Drawer:
36-3/4”
Min.
30”
17-1/2”
23-1/2”
25-1/4”
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
2” Min.
(3”
recommended)
Per warming
drawer
requirement
Single Advantium 240V Installation:
Order a 30” wide single oven cabinet or cut the
opening in a wall to the dimensions shown.
• Always maintain 36-3/4” minimum height from
the floor to the cutout in any single or combined
installation.
• Allow 2-1/8” case trim overlap on the sides and
7/8” overlap on the bottom of the opening for
all models. Allow 1-1/4” case trim overlap on
the top for models PSB9120 and 3/4” overlap
on the top for models ZSC2200, ZSC2200,
ZSC2201 and ZSC2202.
• Oven overlaps will conceal cut edges on all
sides of the opening.
When installed over a single oven or a warming
drawer, allow at least 2” between the two
openings. This separation will provide clearance
for bottom overlap of the Advantium 240V and
the other appliance overlaps.
Construct a solid oven floor of 3/8” min. thick
plywood supported by 2 x 4 or 2 x 2 runners on all
sides.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location do
not obstruct the required interior depth and height.
See Warming Drawer installation instructions for
details.
6
Installation Preparation
Preparation WITHOUT an Accessory Storage Drawer
PREPARE THE OPENING (CONT.)
Installation over a GE/Monogram Oven:
45-1/4”
Min.
30”
17-1/2”
23-1/2”
25-1/4”
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported by
2x4 or 2x2
Runners all
Four Sides
2” Min.
(3” recommended)
Per Oven
Requirement
PREPARE THE OPENING (CONT.)
Installation over a GE/Monogram Oven
and Warming Drawer:
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by
2x4 or 2x2
Runners all
Four Sides
2” Min.
(3” recommended)
Per Oven
Requirement
2” Min.
45-1/4”
Min.
30”
17-1/2”
Per warming drawer requirement
23-1/2”
25-1/4”
• If you are replacing a GE/Monogram electric
double oven with the combined installation of
an Advantium 240V and a single oven, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2” minimum shown.
NOTE: Additional clearances between the
cutouts may be required. Check to be sure
the oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
CAUTION
mounting surface must be capable of supporting
the cabinet load, in addition to the added
weight of this approximate 80-pound oven, plus
additional oven loads of up to 50 pounds or a
total weight of 130 pounds.
PRECAUCIÓN
la superficie de montaje debe poder soportar
la carga del gabinete, además del peso
aproximado de 80 libras del horno, más las
cargas adicionales del horno de hasta 50 libras
o un peso total de hasta 130 libras.
For personal safety, the
Para seguridad personal,
7
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC2202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE
INSTALLATION PREPARATION WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
PREPARE THE OPENING
The Advantium 240V can be installed in
combination with other GE/Monogram
appliances. Always follow each product’s
Installation Instructions to complete the
installation.
Single Advantium 240V Installation:
Order a 30” wide single oven cabinet or cut the
opening in a wall to the dimensions shown.
30”
21”
36-3/4”
Min.
23-1/2”
25-1/4”
Min.*
Construct
Base
Min. 3/8”
Plywood
Supported
by 2x4
or 2x2
Runners all
Four Sides
PREPARE THE OPENING (CONT.)
Single Advantium 240V Installation (cont.)
When installed over a single oven or a warming
drawer, allow at least 2” between the two
openings. This separation will provide clearance
for bottom overlap of the Advantium 240V and the
other appliance overlaps.
Construct a solid oven floor of 3/8” min. thick
plywood supported by 2 x 4 or 2 x 2 runners on all
sides.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
Installation over a GE/Monogram
Warming Drawer:
30”
23-1/2”
25-1/4”
Min.*
21”
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
2” Min.
(3” recommended)
Per warming
drawer
requirement
*
* For existing cutouts, a maximum width of
28-1/2” is acceptable. If the opening is slightly
wider, secure a furring strip on each side of the
cutout for securing the oven.
• Always maintain 36-3/4” minimum height
from the floor to the cutout in any single or
combined installation.
• Allow 3/4” to 2-1/8” case trim overlap on the
sides and 7/8” overlap on the bottom of the
opening for all models. The amount of overlap
on the sides depends on the actual cutout
width. Allow 1-1/4” case trim overlap on the top
for model PSB9120 and 3/4” overlap on the top
for models ZSC2200, ZSC2200, ZSC2201 and
ZSC2202.
• Oven overlaps will conceal cut edges on all
sides of the opening.
36-3/4”
Min.
For existing cutouts, a maximum width of 28-1/2”
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
NOTE: Additional clearances between the
cutouts may be required. Check to be sure
the oven supports above the Warming Drawer
location do not obstruct the required interior depth
and height. See Warming Drawer installation
instructions for details.
8
Installation Preparation
Preparation WITH an Accessory Storage Drawer
NOTE: MODEL ZSC2202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE
INSTALLATION PREPARATION WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.
PREPARE THE OPENING (CONT.)
Installation over a GE/Monogram Oven:
45-1/4”
Min.
30”
23-1/2”
25-1/4”
Min.*
21”
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported by
2x4 or 2x2
Runners all
Four Sides
2” Min.
(3” recommended)
Per Oven
Requirement
PREPARE THE OPENING (CONT.)
Installation over a GE/Monogram Oven
and Warming Drawer:
45-1/4”
Min.
30”
21”
Per warming drawer requirement
23-1/2”
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by
2x4 or 2x2
Runners all
Four Sides
2” Min.
(3” recommended)
Per Oven
Requirement
2” Min.
* For existing cutouts, a maximum width of
28-1/2” is acceptable. If the opening is slightly
wider, secure a furring strip on each side of the
cutout for securing the oven.
• If you are replacing a GE/Monogram electric
double oven with the combined installation of
an Advantium 240V and a single oven, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2” minimum shown.
* For existing cutouts, a maximum width of
28-1/2” is acceptable. If the opening is slightly
wider, secure a furring strip on each side of the
cutout for securing the oven.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location do
not obstruct the required interior depth and height.
See Warming Drawer installation instructions for
details.
CAUTION
mounting surface must be capable of supporting
the cabinet load, in addition to the added
weight of this approximate 80-pound oven and
30-pound drawer, plus additional oven loads of
up to 50 pounds or a total weight of 160 pounds.
PRECAUCIÓN
la superficie de montaje debe poder soportar
la carga del gabinete, además del peso
aproximado de 80 libras del horno y las 30
libras del cajón, más las cargas adicionales
del horno de hasta 50 libras o un peso total de
hasta 160 libras.
For personal safety, the
Para seguridad personal,
9
Installation Instructions
1
REMOVE THE PACKAGING AND PARTS
• Remove all packing material and tape.
• Locate parts package containing mounting
screws.
• Remove the oven from the carton. Do not lift unit
by handle or conduit. Two people are required to
lift this oven.
• Open the door and remove any packaging in
oven.
Owner’s
Manual
Rack
Owner’s Manual
Cook Book
Glass Tray
Metal Trays (2)
Installation
Instructions
Cooking
Guide
Cooking Guide
Turntable Ring
Metal Grill Tray
Bottom Trim
6 Brass Screws
(3 required, 3 extra)
5 Color Matched Screws
(4 required, 1 extra)
IMPORTANT: If installing the Advantium 240V
Oven with an accessory storage drawer, read the
storage drawer assembly instructions to assemble
the products together before proceeding to Step 2.
10
Loading...