GE PSB2200NWW, PSB2200NBB User Manual
PSB2200N
Cutout width
25-1/8"
30
Required
cutout location
36-3/4"
minimum
from floor
Junction
box
location
(240-Volt
models only)
A=Allow 1" overlap of oven over top and bottom
edges of cutout.
B=Allow 11/16"-3/4" for overlap ov oven over side
edges of cutout.
4-3/16
17-1/2"
Cutout height
A
B
23-1/2"
Cutout depth
29-25/32"
21-1/2"
Excluding
Handle
Construct Solid
Bottom Min.
3/8" Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
Conduit
(48-1/2"
long)
1" Min. above toekick or adjust
to oven installation height
2" MIN between cutouts
2-1/2" MIN bet ween cutouts
recommended—2" MIN required
9-1/4" cutout height
28-1/2" cutout width
Junction box location
A
B
A
B
Construct Solid Bottom
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
4-3/16
D
Excluding
Handle
H
W
Conduit
(46" long)
Cabinet width
(240-volt models only)
C
L
(Must support 130 lbs.)
2 x 4’s or
equivalent
solid floor
Suitable
bracing
to support
runners
21-5/8"
over centerline
of cabinet
GE Profile Advantium® 240 Wall Oven
Advantium wall oven/GE Profile cooking tower dimensions and cabinet installation information (in inches)
Note: Cabinets
installed adjacent
to wall ovens must
have an adhesion
spec of at least a
194°F temperature
rating.
Note: 2" minimum
between cutouts
when installed
above warming
drawer or single
wall oven.
Installation
Information:
Before installing,
consult installation
instructions packed
with product for current
dimensional data.
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
A=Allow 7/8” overlap of oven over bottom and 1/4" overlap at top
edges of cutout.
B=Allow 2-1/8” for overlap of oven over side edges of cutout.
A=Allow 7/8” overlap of oven over bottom and 1/4" overlap at top
edges of cutout.
B=Allow 2-1/8” for overlap of oven over side edges of cutout.
Cabinet
Width
(inches)
PSB2200/1 without
accessory drawer
PSB2200/1 with
accessory drawer
*For existing cutouts a maximum width of 28-1/2" is acceptable
30 29-25/32 19 -1 /8 21 -1/ 2 25-1/8 17-1 /2 2 3-1 /2
30 29-25/32 2 2-1 /4 21-3/4
W
WidthH Height
Specification Created 9/08
D
Depth
(excluding
handle)
X
Cutout
Width
25-1/8 to
28 -1 /2 *
Y
Cutout
Height
Cutout
Depth
(minimum)
21 23 -1 /2
Listed by
Underwriters
Laboratories
240 442
Z
PSB2200N
Installation over a GE/Monogram
Warming Drawer:
30”
23-1/2”
25-1/4”
Min.
21”
2” Min.
(3” recom mended)
Per warming
drawe r
requi rement
Constru ct
Solid Bottom
Min. 3 /8”
Plywood
Support ed
by 2x4 or 2x2
Runners all
Four S ides
5” m in.
from floor
1” m in.
abov e
toek ick
Warming Drawer:
Construct Solid
Bottom Min.
3/8” Pl ywood
Supporte d by
2x4 or 2x2
Runners all
Four Si des
30”
23-1/2”
21”
2” Min.
Per Oven
Requirement
Per war ming drawer requirement
2” Min.
(3” recom mended)
25-1/4”
Min.
5” m in.
from floo r
1” m in.
abov e
toek ick
30”
23-1/2”
25-1/4”
Min.
21”
Construct
Base
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
5” m in.
from floor
1” m in.
abov e
toek ick
PSB2200N
GE Profile Advantium® 240 Wall Oven
GE Profile Advantium® 240 Wall Oven
Preparation WITH an Accessory Drawer
Prepare the opening
The Advantium 240V can be installed in combination with
other GE/Monogram appliances. Always follow each product's
Installation Instructions to compete the installation.
Single Advantium 240V Installation:
Order a 30" wide single oven cabinet or cut the opening in a wall
to the dimensions shown.
* For existing cutouts, a
maximum width of 28-1/2"
is acceptable. If the opening
is slightly wider, secure a
furring strip on each side of
the cutout for securing the
oven.
• Always maintain 36-3/4"
minimum height from
the floor to the cutout in
any single or combined
installation.
• Allow 3/4" to 2-1/8" case
trim overlap on the sides
and 7/8" overlap on the
bottom of the opening for
all models. The amount of overlap on the sides depends on the
actual cutout width. Allow 1-1/4" case trim overlap on the top for
models PSB2200 and PSB2201 and for models ZSC2200, ZSC2201
and ZSC2202.
• Oven overlaps will conceal cut edges on all sides of the opening.
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
Prepare the opening (cont.)
When installed over a single oven or a
warming drawer, allow at least 2" between
the two openings. This separation will
provide clearance for bottom overlap of the
Advantium 240V and the other appliance
overlaps.
Construct a solid oven floor of 3/8" min. thick
plywood supported by 2 x 4 or 2 x 2 runners
on all sides.
• the support must be level and rigidly
mounted, flush with the bottom edge of
the cutout.
* For existing cutouts, a maximum width of
28-1/2" is acceptable. If the opening is slightly
wider, secure a furring strip on each side of
the cutout for securing the oven.
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
Installation over a GE/Monogram Oven
and Warming Drawer:
* For existing cutouts, a maximum width of
28-1/2" is acceptable. If the opening is slightly
wider, secure a furring strip on each side of
the cutout for securing the oven.
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
CAUTION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight
of this approximate 80-pound oven and 30pound drawer, plus additional oven loads of up
to 50 pounds or a total weight of 160 pounds.
Listed by
Underwriters
Laboratories
Specification Created 9/08
240 442
Loading...