GE PSB1200NBB01, PSB1200NWW01, PSB1201NSS01, ZSC1201NSS01, ZSC1202NSS01 Installation Guide

Installation

I struct" n

Advantium ®120V
Built-ln SpeedCook

Ovens

PSB1200
PSB1201
ZSC1201
ZSC1202

For a Spanish version of this manual, visit our Website at ge.com.
Para cons@tar una version en espaflol de este manual de instrucciones,
visite nuestro sitiode internet ge.com.

i49-40593-! i

HFL5906090!

12-08 JR

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IN PORTANT- Savetheseinstructions

for local inspector's use.

IM PORTANT-Observeollgoverningcodes

ond ordinonces.

• Note to Installer- Be sure to leave these
instructions with the Consumer.

• Note to Consumer- Keep these instructions
with gour Owner's Honuol for future reference.

• Skill Level- Instollotion of this opplionce

requires bosic mechonical and electrical skills.

• Completion Time - 1 Hour.

• Proper instollotion is the responsibility

of the instoller. Product foilure due to improper
instollotion is not covered under the worrontg.

See Owner's Honuol for worront9 informotion.

NOTE:This oven isonly opproved to be instolled
under the specific models as labeled on this unit.

IMPORTANT- Use thisoven onlg

foritsintendedpurpose.Never use the oven
forworming orheotingo room. Prolongeduse

ofthe oven without properventilationcan
be hazardous.

-&CAUTION:

For personol safety, remove house fuse or oven
circuit breaker before beginning installation

to ovoid severe or fatal shock injurg.

-&CAUTION:

For personol safety, the mounting surfoce
must be copoble of supporting the cobinet Iood,

in oddition to the odded weight of the 80-pound
oven ond 30-pound drower, plus odditionol oven

Ioods of up to 50 pounds or o total weight of up
to 160 pounds.

CONTENTS

Design Information

Models Avoiloble ......................................................................2

Product Dimensions and Clearances ............................3

Tools ond Ports Required ....................................................3

Ports Supplied ..........................................................................:3

Electricol Tools ond Ports Required ................................:3

Advonce Plonning ..................................................................3

Installation Preparation

Electrical Requirements ........................................................4

Install Junction Box ................................................................4

Preparing the Opening (installation without

an accessorg storage drawer) ..................................5-8

Preparing the Opening (installation with

an accessorg storage drawer) ..............................9-12

Installation Under a :36" Cooktop ..................................12

Installation Instructions

Step 1, Remove Pockoging ond Parts ........................1:3

Step 2, Instoll Door Trim ....................................................14

Step :3,Route Conduit ........................................................14

Step 4, Instoll Bottom Trim ..............................................15

Step 5, Instoll Mounting Screws ....................................15

Step 6, Finalize Installation ..............................................15

MODELS AVAILABLE

Profile Models:
PSB1200WW-White*

PSB1200BB-Black
PSB1201SS-Stainless Steel

Monogram Models:

ZSC1201SS-Stoinless Steel
ZSC1202SS-Stoinless Steel**

*No color-matched drawer available for this model.

**This unit cannot be installed with an accessorg

storage drawer.

-&CAUTION:

If instolling the Advontium 120V Oven below 36",
gou must use the plastic bottom trim due to burn

risk to children. The plostic trim octs os insulation
and will help prevent burns to children from hot

surfoces.

-&CAUTION:

If instolling the Advontium 120V Oven below 36",
do not remove the plostic door trim due to burn

risk to children. The plostic trim octs os insulation
and will help prevent burns to children from hot

surfoces.

Design Information

PRODUCT DIMENSIONS AND CLEARANCES

_21-1/2"

1-1/8"

/

\

13/16" _

5/8"

TOOLS AND PARTS REQUIRED

(NOT SUPPLIED}

• #2 Phillips screwdriver

• Hand-held drill

• High speed drill bit, 3/32" diameter

• 3/8" slot-head screwdriver

• Level

I Saw

• 2 x 4 or 2 x 2 lumber for installing runners
or 3/8" plgwood for floor (if required)

Wood screws or other hardware for installing

runner or shelf to support oven (if required)

Safetg glasses or goggles

PARTS SUPPLIED

• 6 screws (3 required, 3 extra)

• 5 color-matched screws (4 required, 1 extra)

• Bottom trim (2)

NOTE: Appearance will vary by model.

29-3/4"

LJ

__ m

ADVANCEPLANNING

• These ovens mag be installed directlg into a 30" wide
oven cabinet.

• Cutout dimensions are NOTthe same for installation
with or without an accessorg storage drawer.

Make sure to use the correct cutout when preparing
the opening.

NOTE:ZSC1202 models CANNOT be installed

with an accessorg storage drawer. See Installation

Preparation Without an Accessorg Storage Drawer

for this model.

Allow for clearance to adjacent corners, walls,
drawers, etc.

The oven must be securelg installed in a cabinet
that is firmlg attached to the house structure.

Weight on the oven door could cause the oven
to tip and result in injurg. Never allow angone

to climb, sit, stand or hang on the oven door.

If installing the drawer accessorg, the drawer must
be assembled to the oven prior to installation into

the cabinet. See the Accessorg Storage Drawer

Assembl£ Instructions.

1

19"

Installation Preparation

ELECTRICAL REQUIREMENTS

Single Advantium 120 Installation:
This product requires a 120-volt, 60 Hz, 1S-amp circuit

and draws 1.8 kilowatts. This product must be
connected to a supply circuit of the proper voltage
and frequency.

• Wire size must conform to the requirements of the
National Electrical Code or the prevailing local code

for this kilowatt rating.

• The power supply cord and plug should be brought

to a separate 15 or 20 ampere branch circuit single
grounded receptacle. The outlet box should be
located within reach of the 48" power cord.

ELECTRICAL LOCATION

11

t

9"

Locate outlet box in the shaded area

Install a recessed electrical outlet in the back wall

of the opening within 6" of either side and at least
9" above the cutout floor.

IMPORTANT: (Please read carefullg).

The power cord of this appliance is equipped with

a three-prong (grounding) plug that mates with
a standard three-prong grounding wall receptacle

to minimize the possibility of electric shock. The

customer should have the wall receptacle and
circuit checked by a qualified electrician to make
sure the receptacle is properlg grounded and has

the correct polaritg.

• Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the consumer to have it replaced with
a properly grounded three-prong wall receptacle.

Do not, under ang circumstances, cut or remove

the third (ground) prong from the power cord.

DO NOT USE AN EXTENSION CORD.

4

Installation Preparation

PreparationWITHOUTanAccessoryStorage

PREPARE THE OPENING

The Advantium 120V can be installed in
combination with other GE/Monogrom oppliances.

AlwoLIs follow eoch product's Installotion

Instructions to complete the installation.

Single Advantium 120V Installation:
Order a 30" wide single oven cobinet or cut

the opening in a wall to the dimensions shown.

Drawer

PREPARE THE OPENING {cont.)

Installation over a GE/Monogram

Warming Drawer:

23-1/2"

_ Supp0rted

17-1/2"

Construct
SolidBottom

Min. 3/8"
Plywood

by2x40r2x2
Runnersall

FourSides

2" Min.
(3" Recommended)

PerWarming
Drawer

Requirement

Construct

\\

\

• Allow 2-1/8" cose trim overlop on the sides,
1-1/16" overlop on the top ond 7/8" overlop
on the bottom of the opening for oll models.

• Oven overlaps will conceal cut edges on all sides
of the opening.

When instolled over o single oven or o warming
drower, allow ot least 2" between the two openings.
This separotion will provide clearonce for bottom
overlap of the Advantium 120V and the other
applionce overlaps.

Construct o solid oven floor of 3/8" min. thick plgwood
supported bg 2 x 4 or 2 x 2 runners on oll sides.

• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.

\\\\

_Plyw00d

Base
Min. 3/8"

Supported
by2x40r

2 x 2 Runners
all FourSides

NOTE: Additionol cleoronces between the cutouts

mall be required. Check to be sure the oven supports
above the Warming Drawer Iocotion do not obstruct
the required interior depth and height. See Warming

Drawer installation instructions for details.

Installation Preparation

PreparationWITHOUTanAccessorgStorageDrawer

PREPARE THE OPENING {cont.)

Installationover a GE/Monogram oven:

Construct Solid
Bottom Min.

3/8" Plywood
Supported by

x4or2x2
Runnersall
FourSides

17-1/2"

• If Uou are replacing a GE/IVlonogram electric
double oven with the combined installation

of an Advantium 12OVand a single oven, use
the dimensions shown. The middle rail separating
the two openings may need to be larger than

the 2" minimum shown.

2" Min.

(3" Recommended)

Per Oven
Requirement

PREPARE THE OPENING {cont.)

Installation over a GE/Monogram Oven and

Warming Drawer:

23-1/2"

ConstructSolid
BottomMin.
3/8" Plywood

Supportedby

_2x4or2x2

Runnersall
FourSides

2" Min.
(3" Recommended)

Per Oven
Requirement

Min.

PerWarming
DrawerRequirement

NOTE: Additional clearances between the cutouts

may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation

instructions for details.

(3" Recommended)

-&CAUTION: Forpersonal safety, the

mounting surface must be capable of supporting
the cabinet load, in addition to the added weight

of this approximate 80-pound oven, plus
additional oven loads of up to 50 pounds

or a total weight of 1:30 pounds.

Installation Preparation

PreparationWITHOUTanAccessorgStorageDrawer

PREPARE THE OPENING {cont.)

Installationover another GE/Monogram
Under-the-Counter (UTC) oven:

30" ..........._-- 23-1/2"

Construct Solid
Bottom Min.

3/8" Plywood

_Supported by

2x4or2x2
Runnersall
FourSides

17-1/2"

17-1/2"

Min.

Recommended)

PREPARE THE OPENING {cont.)

Installation under a GE/Monogram
Microwave Oven and over a Warming

Drawer:

30" ....................._,,._,i_3-1/2"

PerOven
Requirement

17-1/2"

PerWarming
Drawer Requirement

ConstructSolid
BottomMin.

3/8" Plywood

ySupported by

2x4or2x2
Runnersall

FourSides

4.5" Recommended)

(3"Recommended)

Min.

Min.

• If Uou are mounting an Under-the-Counter
GE/IVlonogram oven over another, use the
dimensions shown. The middle rail separating

the two openings may need to be larger than
the 2" minimum shown.

NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven

supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation

instructions for details.

_4,CAUTION: Forpersonal safety, the

mounting surface must be capable of supporting
the cabinet load, in addition to the added weight

of this approximate 80-pound oven, plus
additional oven loads of up to 50 pounds

or a total weight of 1:30 pounds.

Installation Preparation

PreparationWITHOUTanAccessorgStorageDrawer

PREPARE THE OPENING {cont.)

Installation beside another GE/Monogram
Built-in Speedcook Oven:

• If you are mounting one Under-the-Counter
GE/IVlonogram oven beside the other, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than

the a-1/2" minimum shown.

PREPARE THE OPENING {cont.)

23-1/2"

/

17-1/2"

Min.

(5-1/2"Recommended)

Installation under a GE/Monogram 30" or 36" Cooktop or Countertop:

Gas or electric cooktops mag be installed over this oven. See cooktop installation instructions for the cutout
size. See the label on top of the oven for approved cooktop models. This oven requires a separate, properly
grounded 15-Amp, 120-Volt, 60Hz power supplg. The cooktop requires a separate power supplg. Use a 36"

or wider base cabinet.

Cooktop

36"

_- Countertop

Height

17_1/2"

/4"

25-1

Cooktopheightincludingdepth

of electricalboxonsomemodels.

Referto cooktopinstallation
instructions.

Nominimumclearancerequired
betweencooktopandoven.

4" High
Toekick J_

NOTE: Theoven is only approvedto be installed
under the specific models as labeled on the unit.

Installation Preparation

PreparationWITH anAccessoryStorageDrawer

NOTE:MODELZSC1201CANONLYBEINSTALLEDWITH ANACCESSORYSTORAGEDRAWERIFINSTALLEDABOVE36-3/4".
MODELZSC1202CANNOTBEINSTALLEDWITHAN ACCESSORYSTORAGEDRAWER.SEEINSTALLATIONPREPARATIONWITHOUT
ANACCESSORYSTORAGEDRAWERFORTHIS MODEL.

PREPARE THE OPENING {cont.)

The Advantium 12OV can be installed in
combination with other GE/Monogram appliances.

Always follow each product's Installation
Instructions to complete the installation.

Single Advantium 12OV Installation:
Order a 30" wide single oven cabinet or cut

the opening in a wall to the dimensions shown.

25-1/4"___,.

4 .... Min.

21"

\\

36-3/4"

Min.*

ConstructBase

\\\

\

\

Min. 3/8" Plywood

"Supported by 2 x 4

or 2 x 2 Runners
all FourSides

*Requiredfor

Monogrammodels

PREPARE THE OPENING {cont.)

Installation over a GE/Monogram

Warming Drawer:

23-1/2"

ConstructSolid
BottomMin. 3/8"

f PlywoodSupported

by2x4or2x2
Runnersall FourSides

21"

36-3/4"

Min.*

NOTE: Additional clearances between the cutouts
mag be required. Check to be sure the oven

supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation

instructions for details.

2" Min.
(3"Recommended)

PerWarming
Drawer

Requirement

×-Requiredfor

Monogrammodels

• Allow 2-1/8" case trim overlap on the sides,
1-1/16" overlap on the top and 7/8" overlap
on the bottom of the opening for all models.

• Oven overlaps will conceal cut edges on all sides
of the opening.

When installed over a single oven or a warming
drawer, allow at least 2" between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 120V and the other
appliance overlaps.

Construct a solid oven floor of 3/8" min. thick plgwood
supported bg 2 x 4 or 2 x 2 runners on all sides.

The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.

Installation Preparation

PreparationWITH anAccessoryStorageDrawer

NOTE:MODELZSC1201CANONLYBEINSTALLEDWITH ANACCESSORYSTORAGEDRAWERIFINSTALLEDABOVE36-3/4".
MODELZSC1202CANNOTBEINSTALLEDWITHAN ACCESSORYSTORAGEDRAWER.SEEINSTALLATIONPREPARATIONWITHOUT
ANACCESSORYSTORAGEDRAWERFORTHIS MODEL.

PREPARE THE OPENING {cont.)

Installationover a GE/Nonogram Oven:

30" 23-1/2" b

.......................... _ _----- ______

_,-- 25-1Min/4"._____,,.

36-3/4"

Min.

45-1/4"

Recommended

* For existing cutouts, a maximum width of 28-1/2"

is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.

, If you are replacing a GE/Monogram electric

double oven with the combined installation

of an Advantium 120V and a single oven, use
the dimensions shown. The middle rail separating
the two openings mag need to be larger than

the 2" minimum shown.

Construct Solid
Bottom Min.

3/8" Plywood

_Supported by

2x4or2x2
Runnersall
FourSides

2" Min.
(3" Recommended)

PerOven
Requirement

×%quiredfor

Monogrammodels

PREPARE THE OPENING {cont.)

Installation over a GE/Monogram Oven and
Warming Drawer:

23-1/2"

ConstructSolid
BottomMin.

3/8" Plywood
Supportedby

_2x4or2x2

Runnersall
FourSides

2" Min.
(3" Recommended)

PerOven
Requirement

Min.

(3" Recommended)

Drawer Requirement

* For existing cutouts, a maximum width of 28-1/2"

is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.

NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven

supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation

instructions for details.

.4,CAUTION: Forpersonal safetg, the

mounting surface must be capable of supporting
the cabinet load, in addition to the added weight

of this approximate 80-pound oven and 30-pound
drawer, plus additional oven loads of up to

50 pounds or a total weight of 160 pounds.

10

Installation Preparation

PreparationWITH anAccessoryStorageDrawer

NOTE:MODELZSC1201CANONLYBEINSTALLEDWITH AN ACCESSORYSTORAGEDRAWERIFINSTALLEDABOVE36-3/4".
MODELZSC1202CANNOTBEINSTALLEDWITH ANACCESSORYSTORAGEDRAWER.SEEINSTALLATIONPREPARATIONWITHOUT

ANACCESSORYSTORAGEDRAWERFORTHIS MODEL.

PREPARE THE OPENING {cont.)

Installationover another GE/Monogram
Under-the-Counter (UTC) oven:

30"-- I _,- 23-1/2"

-,4 ............................ _ ---- ---[-- ---

Construct Solid
Bottom Min.

3/8" Plywood

_Supported by

2x4or2x2
Runnersall
FourSides

:2" Min.

(3" Recommended)

1"*

*Profilemodelsonly

PREPARE THE OPENING {cont.)

Installation under a GE/Monogram
Microwave Oven and over a Warming

Drawer:

.................... 23-1/2"

ConstructSolid
BottomMin. 3/8"

_Plywood Supported

by2x4or2x2
Runnersall Four

Per Oven
Re(uirement

Sides

3.5"Min.
(4.5"Recommended)

1"*

2" Min.

PerWarming

DrawerRec '

(3"Recommended)

×-Profilemodelsonly

• If Uou are mounting an Under-the-Counter
GE/Monogram oven over another, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than

the 2" minimum shown.

NOTE: Additional clearances between the cutouts

may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth
and height. See Warming Drawer installation

instructions for details.

-&CAUTION: Forpersonal safety, the

mounting surface must be capable of supporting
the cabinet load, in addition to the added weight

of this approximate 80-pound oven, plus
additional oven loads of up to 50 pounds

or a total weight of 1:30 pounds.

11

Installation Preparation

PreparationWITH anAccessoryStorageDrawer

NOTE:MODELZSC1201CANONLYBEINSTALLEDWITH AN ACCESSORYSTORAGEDRAWERIFINSTALLEDABOVE36-3/4".
MODELZSC1202CANNOTBEINSTALLEDWITH ANACCESSORYSTORAGEDRAWER.SEEINSTALLATIONPREPARATIONWITHOUT
ANACCESSORYSTORAGEDRAWERFORTHIS MODEL.

PREPARE THE OPENING {cont.)

Installation beside another GE/Monogram
Built-in Speedcook Oven:

• If you are mounting one Under4he-Counter

GE/Monogrom oven beside the other, use
the dimensions shown. The middle rail seporating
the two openings mog need to be larger than

the 4-1/2" minimum shown.

PREPARE THE OPENING {cont.)

21"

23-1/2"

/

4-1/2" Min.
(5-1/2" Recommended)

Installation under a GE Profile 30" or 36" Cooktop or Countertop:

Gas or electric cooktops mag be installed
over this oven. See cooktop installation

instructions for the cutout size. See the
label on top of the oven for approved

cooktop models. This oven requires
o seporote, properlg
grounded 15-Amp,

120-Volt, 60Hz power
supplg. The cooktop
requires a separate power
supplg. Use a 36" or wider

base cabinet.

IMPORTANT:

For Profile models onlg.
The Monogram oven

and drawer combination
cannot be installed below

a countertop.

23-1/2"

4" High f

Toekick

Cooktop

NOTE: Theoven is only approved to be installed
under the specific models as labeled on the unit.

36"

_- Countertop

Height

\\

,pheightincludingdepth

of electricalboxonsomemodels.

Referto cooktopinstallation
instructions.

Nominimumclearancerequired
betweencooktopandoven.

12

Installation Instructions

| REMOVE THE PACKAGING AND PARTS

• Remove all packing material and tape.

• Locate parts package containing mounting screws.

• Remove the oven from the carton. Do not lift unit
bg handle or conduit. Two people are required to lift

this oven.

• Open the door and remove ang packaging in oven.

Rack

Owner's

Hanual

Installation
Instructions

Owner'sManual Installation

Instructions

Cook Book

Cooking
Guide

CookBook CookingGuide

GlassTray TurntableRing

_4,CAUTION: ifinstalling theAdvantium

120V Oven below 36", you must use the plastic

bottom trim due to burn risk to children. The
plastic trim acts as insulation and will help

prevent burns to children from hot surfaces.

I ]

BottomTrim- Plastic

BottomTrim- Metal

6 BrassScrews

(3 required,3 extra)

IMPORTANT: If installing the Advantium 120V Oven
with an accessory storage drawer, read the storage
drawer assembly instructions to assemble the
products together before proceeding to Step 2.

5 C010r-MatchedScrews

(4 required,1 extra)

Metal Trays(2)

13

Installation Instructions

[_] DOOR TRIM REMOVAL FOR ABOVE

36" INSTALLATION ONLY

If installing the Advantium 120V Oven above 36"

from the floor, you mag remove the plastic trim
from the bottom of the door for esthetic purposes

if desired.

-&CAUTION: ifinstalling theAdvantium

120V Oven below 36", do not remove the

plastic door trim due to burn risk to children.
The plastic trim acts as insulation and will help
prevent burns to children from hot surfaces.

• If installing above 36", remove the 3 screws that
secure the plastic trim to the bottom of the door.

• Discard plastic trim. Replace screws.

SLIDE THE OVEN INTO THE CUTOUT

CAUTION: Twopeopleare required to

lift the oven into the opening. Grasp the bottom
at front and rear. DO NOT USETHE HANDLE TO LIFT

THE OVEN. DAMAGE WILL OCCUR.

• Lift and hold the oven at the front of the opening.
Hold the oven at an angle and plug in the power

cord.

• Carefullg, slide the oven into the cabinet part
wag. Leave the oven a few inches forward of

the cabinet frame.

• Check to be sure the power cord is not trapped

J

under the oven or along the sides of the oven.

&

14

Installation Instructions

[-4-I INSTALL BOTTOM TRIM

CAUTION: ifinstallingtheAdvantium

120V Oven below 36",you must use the plastic

bottom trimdue to burn risktochildren.The plastic
trimactsas insulationand willhelppreventburns

tochildrenfrom hot surfaces.

NOTE: If installing the Advantium 120V Oven

with an accessory storage drawer, the bottom trim
is not required. Proceed to Step 5.

• Installation Below 36", align trim tabs on the plastic
trim to slots in the bottom of the oven.

_-Plastic Trim

• Installation Above 36", align trim tabs on the plastic

or metal trim to slots in the bottom of the oven.

_, ,_ .... Plastic Trim

I _- OR

[---]_ i l--_l_ ...... Metal Trim

[_] INSTALL MOUNTING SCREWS

_o

CZZZZ3CZZ:] CZZC] CIK13 [ZZZZD CZIZ3

• Slide the oven the remaining way into the opening
so that the side flanges and control panel are

against the cabinet frame. Make sure that the oven
is centered in the opening.

• Open the door, place a turntable tray in the oven
and make sure that the tray in the unit is level.

• Drill pilot holes through the side flanges.

• Drive the color-matched screws into the side

flanges. It is recommended that the screws

be hand tightened.

If installing oven with an accessorg storage
drawer:

• Open the drawer.

• Drill pilot holes through the side flanges.

• Drive color-matched screws into the side flanges.
It is recommended that the screws be hand

tightened.

• Secure the bottom trim to the bottom of the oven
using 3 screws provided.

INSTALL BOTTOM TRIM WITH

ACCESSORY DRAWER

If installing with an accessory drawer, see

installation instructions on page 17 or instructions
that come with the accessory drawer.

NOTE: If installing the Profile Advantium 120V Oven
with an accessory storage drawer, you must use
the Under-the-Counter (UTC)mounting bracket for
the drawer.

If installing the Monogram Advantium integrated
model ZSC1201 above 36'%the UTCmounting bracket

for the accessory storage drawer must be used.

| FINALIZE INSTALLATION

• Turn power on at the source. The interior light
should come on when the door is opened.

• Refer to Owner's Manual for operating instructions.

15

GE Consumer

& Industrial Appliances

As e

bl Instructions

Advantium ®Built-in Accessory
J×2200, J×2201, Z×2201

BEFORE YOU BEGIN

Readthese instructions completely and carefully. Read

the Installation Instructions for the Advantium 120V or
240V oven completely and carefully for cutout

dimensions and step-by-step instructions.

IMPORTANT- savetheseinstructionsfor

local inspector's use.

IMPORTANT- Observe allgoverningcodes

and ordinances,

• NOTE TO INSTALLER: Be suretoleavethese
instructionswiththeConsumer,

• NOTE TO CONSUMER: Keep theseinstructionswith
yourAdvantium 120V or240V Oven Owner'sManual

forfuturereference,

• SKILL LEVEL: Installation of this appliance requires
basic mechanical skills.

Storage

MODELS AVAILABLE

Profile Models:
JX2200BB-BIock

JX2201SS-Stoinless Steel

Monogram Models:
ZX2201SS-Stainless Steel (for installation above 36" only)
NOTE: Advantium 240V model ZSC2202SS and

Advantium 120V model ZSC1202 CANNOT be
installed with an accessory storage drawer. See

Installation Preparation Without on Accessory Storage
Drawer in the Installation Instructions for these models.

PRODUCT DIMENSIONS AND CLEARANCES

Drawer

• COMPLETION TIME: One hour with the installation

of an Advantium 120V or 240V oven.

• Proper installation isthe responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty. See the Advontium

120V or 240V Oven Owner's Manual for warranty

information.

_5"

Allow 15" clearance

when fully open

NOTE:Appearance will vary by model.

TOOLS REQUIRED

• #2 Phillipsscrewdriver

PARTS SUPPLIED

• 2SideSupports

• Screws(8)
Screws(color-matched)(5)

Under-the-Counter Mounting Bracket(1)

16

ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN

REMOVE PACKAGING AND PARTS

• Remove the drawer from the carton.

• Remove all packing material and tape.
Open the drawer and remove anLl parts inside.

Locate parts.

Assemblg

Instructions

SideSupports(2)

AssemblyInstructions

Under-the-C0unter(UTC)

MountingBracket

Screws C010r-Matched

(6required, Screws

2 extra) (4required,

1extra)

ASSEMBLING THE OVEN TO DRAWER

Place storage drawer on a surface with

[]

the front of drawer hanging over the edge
of the surface. Not placing the front edge
of drawer over the edge of the surface mall
result in damage to the drawer since the front
edge of drawer hangs below the bottom

of drawer.
Place the oven on top of the storage drawer.

Make sure that the back and sides of the oven
align with the back and sides of drawer.

NOTE: The bottom of the oven side flanges will
sit directlll in front of the top of the storage
drawer side flanges.

i-_ UNDER-THE-COUNTER {UTC)

MOUNTING BRACKET INSTALLATION

NOTE: For UTC models PSB1200, PSB1201 and

ZSC1201 onlLl.

Open the accessorg drawer so gou have
access to the top bracket.

Remove the three screws securing the top

bracket.

rc1 Install the new UTC mounting bracket using

the screws removed previouslLl.

rD1 Close the drawer and proceed with the

installation.

17

ASSEMBLY TO ADVANTIUM BUILT-IN SPEEDCOOK OVEN

ASSEMBLING THE OVEN TO DRAWER

{cont.)

[_ Remove the front two bottom screws on each

side of the oven and the top center screw on
each side of the storage drawer.

F6]Place the side supports into the tabs on the

drawer and secure using the screws supplied
and the screws removed in Step C.

Side

Support

120vonly f

F£1The oven and storage drawer assemblg is now

readg to be installed. Return to the Advantium

120V or 240V Built-in SpeedCook Oven
Installation Instructions to complete

the installation.

18

Notes

19

Printed in Korea

NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.

NOTE: Product improvement is o continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications ore subject to change without notice.

GE Consumer & Industrial
Appliances

General Electric Company

Louisville, KV/40225

ge.com