GE PMC-MMSI Data Sheet

Intelligent Platforms

PMC-MMSI

Single-function PMC Interface

Features

• 10 Mbit per sec EBR-1553/MMSI

• Single Function Interface – 12 Line BC with Composite Monitor

Output or 12 Remote Terminals or Dual Mode Monitor (cable supports eight lines and monitor)

•

Supports

Both

Specification

andLink Modes

– Hardware Line RT Identification

• Bus Controller (BC) – BC->RT, RT->BC – Mode Codes, Broadcast and single-shot

messaging – Programmable time delays – Major/Minor frames – Logical Hub Composite Monitor output

• Remote Terminal (RT) – RT data wrapping – Multiple RT buffers – Automatic Mode Code and Status Bit

responses

• Bus Monitor (BM) – Error detection – Both terminal and composite

monitoring modes

– 48-bit

time-tagging

andLabWindows/CVI

• Architecture – CORE-MMSI architecture – BC & RT link list structures – 1 Mbyte RAM per channel – High impedance idle txcvrs

• Software Support – High-level API – Source code included

The PMC-MMSI from GE Intelligent Platforms is a flexible, current release, EBR-1553/ MMSI PMC mezzanine board interface. The PMC-MMSI includes advanced API (Application Programming Interface) software that will reduce application development time. Standard features include LTC1685 RS-485 fail-safe transceivers, 1 Mbyte of RAM, 48-bit message time-tagging, extensive BC & RT link-list structures, error detection, automatic/manual RT Status Bit and Mode Code responses, along with advanced BC functionality. Transition cabling to standard 1553 cable jacks is provided for eight lines and one monitor line.

EBR-1553/MMSI Interfaces

The PMC-MMSI interfaces incorporate the latest release of the EBR-1553/MMSI SAE AS-1A2 task group specification and support the hardwire Link-Mode as typically used for weapon racks.

Single-function Interfaces

Each single-function PMC-MMSIinter- face has all the features and

functionality

required

to perform the EBR-1553/MMSI and Link-mode specifications for a 12-line Bus Controller, 12 Remote Terminals or a Dual Mode Monitor, one function per interface.

In Bus Monitor mode the PMC-MMSI supports either a Composite Monitor input or an individual Terminal Monitor with error detection.

Software

GE provides an MMSI API in source

code,

along

with driver support for 32-bit/64-bit Microsoft®Windows®XP/Vista/Server 2008/7, 32-bit Windows®NT, and VxWorks operating systems.

defense.ge-ip.com/avionics

res er

ved. Al l other brands or nam esare p roperty

of the ir respe ctive h olders. Sp ecifica tionsare s ubject to change w ithout not ice.

09.13 GFA-1045A

PMC-MMSI – Single-function PMC Interface

Specifications

Physical

• Single-wide PMC card (74 mm x 149 mm)

• Universal keying (3.3 and 5 volt)

Environmental

• Commercial operating temp. range: 0°C to +70°C

• Storage Temp: -40°C to +100°C

• Relative humidity up to 95% non-condensing

Software

• API - High-level libraries with source code included for 32-bit/64-bit

Microsoft®Windows®XP/Vista/Server 2008/7, 32-bit Windows NT, and VxWorks®operating systems

Connections

• Point to

point

, with 78 ohm terminating resistor

• Front panel bezel

• Transition cabling to 1553 cable jack s included (eight lines, plus monitor)

• Monitor Interface: 78 ohm BM termination

Single-function Operations

• BC or 12 RTs or Dual Mode Monitor

Description

Bus Controller

• Programmable control over

- Major and minor frame co ntent and timing

- Interme ssage gap times

- Response time-out and la te response

- Multiple BC

ret r

• Mo dif y messages, data or setup while card is running

• Inser t aperiodic messages into a run ning BC list

• “On eshot“ mode for si mplified BC op eration

• Se lectable interr upt gen eration and status messa ges

- Full rang e of system con ditions

- All de tected errors

• Err or detection

- Bit count error

- Inverted sync

- Hig h word

- Incorrect RT address

- Low word

- Parity error

• Spec Mode and hardw ire Link-Mode

Remote Termin al

• Multiple RT ope ration (up to 12 RTs)

• Mo dif y data ,status words or setu pwhile card is runnin g

• Programma ble messa ge conten t (linked messag e buffer s)

• Inte rrupts can be generated on a pe rmessage basis upon End of Message and error con ditions

Bus Monitor

• Capture bus traf fic with:

Ti me -tag ging

- Err or sta tus

- Word status

- Messag estatus

- RT re sponse time

• 48-bit, microsecond resolution time tagging

• BC Logical Hub Composite

Traf

fic Mon itor

• Terminal Mon itor

Power

• +3.3V @ 750mA max

• +5V @ 500mA max

On-board Shared RAM

• 1 Mbyte

Options

• PCI or CompactPCI Carrier card

Warranty

• 2 year limited hardware warranty

• No cost library card driver upgrade s

Ordering Options

PMC-MMSI -SF EBR-1553/MMSI 12 line, single -fun ction PMC inter face

PMC-MMSI -SF X EBR-1553/MMSI 12 line, single -fun ction PCI inter face

PMC-MMSI -SF3 EBR-1553/MMSI 12 line, single-function 3U cPCI interface

About GE Intelligent Platforms

GE Intelligent Platforms is a General Electric (NYSE: GE) company, headquartered in Charlottesville, VA and part of GE Energy Management. The company’s Military/Aerospace business, headquartered in Huntsville, AL, and Towcester, England, provides one of the industry’s broadest ranges of high performance, rugged, SWaP-optimized embedded computing platforms. Backed by programs that provide responsive customer support and minimize long term cost of ownership for multi-year programs, GE’s solutions are designed to help customers minimize program risk and cost, and to speed time-to-market. For more information, visit

defense.ge-ip.com.

GE Intelligent Platforms Contact Information

Americas: 1 877 429 1553 Global regional phone numbers are listed by location on our web site at

defense.ge-ip.com/avionics-contacts