GE Monogram ZVB36BH, Monogram ZVB36SH, Monogram ZVB36WH, Monogram ZVB36SHSS, Monogram ZVB36WHWW Dimensions And Specifications

ZVB36SH/BH/WH – GE Monogram 36" Telescopic Downdraft Vents

Dimensions and Specifications (in inches)

For answers to your Monogram,® GE Profile™ or
GE

®

appliance questions, visit our website at

GEAppliances.com or call GE Answer Center

®

service, 800.626.2000.

Specification Created 10/03

130656

Listed by
Underwriters
Laboratories

R

Counter top Requirements

Countertops must have a deep flat surface to
accommodate the cooktop and the vent.
Countertops with a rolled edge and backsplash
may not provide the flat surface area required.

Base Cabinet Requirements

The base cabinet must be deep enough to
accommodate the minimum clearance to the
front edge of the counter top, the cooktop
burner box and the vent.

Downdraf t Vent and Cooktop Cutout

The installation of these downdraft vents
with any Monogram cooktop requires careful
consideration. For accurate planning,
review the individual dimension drawings
for the combined vent and Monogram
cooktop installation.

Before you begin you must:

1. Review countertop dimension illustrations
to be sure you will have enough flat
countertop surface depth.

2. Check to be sure that the total countertop
depth required (including minimum cutout
to front edge depth) allows enough space
for a backsplash.

3. Review the cabinet illustration. Check to
be sure that the interior cabinet depth will
house the cooktop burner box, the vent and
the cutout clearance from the front.

4. When countertop and cabinet depth present
a problem, review Creative Solutions.

5. Carefully review the installation instructions
packed with product or available online at
www.monogram.com.

With careful planning you can achieve a
custom look with minimal adjustments.

All 36” models are equipped with a separate raise/lower switch. The switch must be installed
in a separate location outside of the vent and cooktop cutout.

A

B

27"

2-1/4"

3-1/8"

10-1/2"

3-3/8"

3-3/4"

7-1/2"

6-1/4"

2"

8-1/2"
Lift

7-1/8"

36

34

Separate Raise/Lower Switch

ZVB36SH/BH/WH – GE Monogram 36" Telescopic Downdraft Vents

Creative Solutions

For answers to your Monogram,® GE Profile™ or
GE

®

appliance questions, visit our website at

GEAppliances.com or call GE Answer Center

®

service, 800.626.2000.

Specification Created 10/03

130656

Listed by
Underwriters
Laboratories

R

Against-the-wall installation

Move the base cabinet forward, 3" to 5".
Filler panels or complimentary moldings can
be added to the exposed cabinet sides.

Island or peninsula installation

Use an extra-deep countertop. The countertop
overhang at the front can be adjusted to meet
setback to cutout requirements.

Decorative trim

When the cutout to front edge of the
countertop requirement is more than 2",
add a bullnose trim to the front edge of the
countertop. The additional trim allows the
cooktop to be moved forward, providing
additional countertop depth and interior
cabinet space.

Base Cabinet

Filler Panel

Base Sink

Filler Panel

Maintain Cutout Clearances

to Front Edge as Specified

Cover Panel

Base Sink

End
Panel

Countertop Overhang per Cooktop

Clearances Must be Maintained

DOWNDRAFT

VENT

1-7/8"

Trim

Add a Bullnose
Trim or Decorative
Molding to
Increase
Countertop
Depth and to
Maintain
Required
Clearance From
Front Edge

Optional Accessories

JXRB67 Accessory for indoor remote location

of the blower/motor assembly. Use this kit
when the blower and motor assembly will
be located outside of the cabinet, such as
below the cabinet floor. The assembly will fit
between 16" floor joists.

JXBC67 Outdoor cover accessory for remote
installation of the blower/motor assembly on
an outside wall.

Ductwork

Prepare the ductwork to vent to the outdoors.

• Plan the shortest and straightest route for
venting exhaust to the outdoors.

• The maximum permissible length for the
duct run is 150 feet.

• Use metal ductwork only.

• The downdraft blower system is designed to
use 3-1/4" x 10" duct. It can be transitioned
to 6" round.

• Install a wall cap or roof cap with damper at
the exterior opening. Order the wall cap and
any transition needed in advance.