GE Legend IP User Manual

Page 1

Legend IP

User Manual

Page 2

This document may not be copied or otherwise reproduced, in whole or in part, except as specifically permitted under US and international copyright law, without the prior written consent from GE.

Document number: 1055713A (August 2006)

Disclaimer THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. GE ASSUMES

NO RESPONSIBILITY FOR INACCURACIES OR OMISSIONS AND SPECIFICALLY DISCLAIMS ANY LIABILITIES, LOSSES, OR RISKS, PERSONAL OR OTHERWISE, INCURRED AS A CONSEQUENCE, DIRECTLY OR INDIRECTLY, OF THE USE OR APPLICATION OF ANY OF THE CONTENTS OF THIS DOCUMENT. FOR THE LATEST DOCUMENTATION, CONTACT YOUR LOCAL SUPPLIER OR VISIT US ONLINE AT WWW.GESECURITY.COM.

This publication may contain examples of screen captures and reports used in daily operations. Examples may include fictitious names of individuals and companies. Any similarity to names and addresses of actual businesses or persons is entirely coincidental.

Trademarks and patents GE and the GE monogram are registered trademarks of General Electric.

Legend product and logo are trademarks of GE Security.

Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.

Software license agreement GE software supplied with GE products is proprietary and furnished under license and can be

used or copied only in accordance with the license terms.

THE ENCLOSED PROGRAM IS FURNISHED SUBJECT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. RETENTION OF THE PROGRAM FOR MORE THAN 30 DAYS, OPENING OF THE SEALED WRAPPER, IF ANY, SURROUNDING THE PROGRAM, OR USE OF THE PROGRAM IN ANY MANNER WILL BE CONSIDERED ACCEPTANCE OF THE AGREEMENT TERMS. IF THESE TERMS ARE NOT ACCEPTABLE, RETURN THE UNUSED PROGRAM AND ANY ACCOMPANYING DOCUMENTATION TO GE FOR A FULL REFUND OF THE LICENSE FEE PAID. (FOR INFORMATION REGARDING THE RETURN OF PROGRAMS ENCODED OR INCORPORATED WITHIN EQUIPMENT, CONTACT THE NEAREST GE SALES OFFICE.)

Intended use Use this product only for the purpose it was designed for; refer to the data sheet and user

FCC compliance his equipment has been tested and found to comply with the limits for a Class A digital device,

documentation. For the latest product information, contact your local supplier or visit us online at www.gesecurity.com.

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Page 3

Contents

Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Conventions used in this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii

Safety terms and symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii

References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Chapter 1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Product overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Operational overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

System configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Available protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Chapter 2. Accessing the programming interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Computer versus keypad access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

When is logging on necessary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Multiple users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Using a keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

iii

Chapter 3. Programming tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Web based controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Joystick modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Joystick as simulated mouse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Joystick as PTZ controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Using the graphical keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Inactivity timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Keypad shortcuts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Chapter 4. Basic programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Establishing network connectivity with the dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Addressing the dome and the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Setting the encoder ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Programming presets from the keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Programming presets with the programming interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Programming presets with the web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

ShadowTours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Page 4

Legend IP

User Manual

Chapter 5. Advanced programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Confirming settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Setup menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Memory page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Passcode page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Title/Date page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Network page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Preferences page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Camera menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Privacy Masks page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Settings page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Encoder page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Actions menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Presets page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

ShadowTours page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Macros page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Areas page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Time schedule page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Alarms menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Programming tips for dome alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Summary page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Contact Setup page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Priority page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Display page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Relay Status page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Control menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Command Map page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Power-on and Resume page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Speeds/Tracking page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

System menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Diagnostics page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Status tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Logs page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Page 5

Chapter 6. System operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Viewing video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

Autopan limitations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

Pan and tilt limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

Rebooting versus resetting a dome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101

Rebooting the dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Resetting the dome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Erase settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Controllers and commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

Keypad limitations for calling up presets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Moving camera assemblies between domes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104

Chapter 7. Troubleshooting, maintenance, support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

Identifying a dome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Troubleshooting your Legend IP system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108

Updating the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Contacting technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111

Online publication library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Appendix A. System defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Default programming settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114

Default title positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115

Appendix B. Compatible protocol commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Supported Pelco D and Pelco P commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118

Supported Tyco/AD commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118

Supported Ultrak commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119

Appendix C. Compatible web components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Compatible operating systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122

Compatible web browsers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122

Compatible digital video viewers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122

Appendix D. Configuring point-to-point streaming of Legend IP to SymNet . . . . . . . . . . . . . 123

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124

Firewall configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124

SymNet configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Page 6

Legend IP User Manual

Page 7

Preface

This is the GE Legend IP User Manual for all models with v3.x software. This document includes an overview of the product and detailed instructions explaining:

• how to program; and

• how to operate.

There is also information describing how to contact technical support if you have questions or concerns.

To use this document effectively, you should have the following minimum qualifications:

• a basic knowledge of CCTV systems and components,

• a basic knowledge of electrical wiring and low-voltage electrical connections; and,

• a basic knowledge of computer networking.

vii

Read these instructions and all ancillary documentation entirely before

installing or operating this product. The

most current versions of this and related documentation may be found on our website. Refer to Online

publication library on page 111 for instructions on accessing our online publication library.

Note: A qualified service person, complying with all applicable codes, should perform all required hardware installation.

Conventions used in this document

The following conventions are used in this document:

Bold Menu items and buttons.

Italic Emphasis of an instruction or point; special terms.

File names, path names, windows, panes, tabs, fields, variables, and other GUI elements.

Titles of books and various documents.

Blue italic (Electronic version.) Hyperlinks to cross-references, related topics, and URL addresses.

Monospace Text that displays on the computer screen.

Programming or coding sequences.

Safety terms and symbols

These terms may appear in this manual:

CAUTION: Cautions identify conditions or practices that may result in damage to the equipment or other property.

WARNING: Warnings identify conditions or practices that could result in equipment damage or serious personal injury.

Page 8

Legend IP

viii

User Manual

References

If you want to investigate related topics, these other documents may prove helpful:

• GE Security. Legend IP Installation Manual (1055712)

• GE Security. SymNav Video Navigator User Manual (0150-0303)

• GE Security. SymSecure System Guide (1055580)

• GE Security. SymSecure User Guide (online help)

• GE Security. KTD-405 Controller Keypad User Manual (1036547)

• GE Security. Networking Cable Types Technical Reference Guide (1047213)

• GE Security. ASCII Protocol Reference Manual (1038010)

Page 9

Chapter 1 Introduction

This chapter provides an overview of your Legend IP dome system. Refer to the Legend IP Installation Manual (1055712) for the detailed product contents, components supplied by the customer, dome and system requirements, and system planning.

In this chapter:

Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Operational overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

System configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Available protocols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Page 10

Legend IP

User Manual

Product overview

Legend IP™ is a line of advanced PTZ domes that stream digital video. Digital video is easier to transmit, share, and store than conventional analog video signals. Digital video systems also integrate well into most communications and media networks and are easily operated from software applications that manage digital video, such as GE’s SymSecure™ or SymNav™. SymSecure is GE’s complete digital video management software. SymNav is GE’s free digital video viewer that is provided with each dome. Compatible software applications, like these, allow you to control your domes and video over an IP (Internet Protocol) network from computers, instead of using analog keypads, recorders, multiplexers, and switchers.

Legend IP domes use an MPEG-4 video encoder to compress and digitize streaming video up to 30 fps (frames per second) for NTSC and up to 25 fps for PAL. At the maximum frame rates, the domes require a bandwidth from 1 to 2 Mbps (Megabits per second). The encoder supports QCIF, CIF, and D1 video resolutions. The MPEG-4 video stream that is created is compatible with GE’s SymDec family of MPEG-4 recorders, SymNet family of MPEG-4 codecs, and SymNav software. The Legend IP interface is open to allow compatibility with third party software and recording equipment.

Besides their networking ability, Legend IP domes also feature powerful cameras, SilkTrak™ direct-drive positioning for smoother camera travel, a graphical programming interface for easier customization of camera settings, passcodes for protection against unauthorized access, and the ability to flash software upgrades over your IP network using a standard web browser.

CAUTION: To ensure the security of your surveillance system, your IP network should be isolated and secured from

unauthorized access.

The Legend IP protocol is backward compatible with the Digiplex protocol. You can replace older domes in an existing Digiplex system with Legend IP domes. You must, however, replace the entire dome (camera and housing), because the hardware is not backward compatible.

Operational overview

Legend IP domes work in both IP network and in analog systems (System configurations on page 3). In a network system, Legend IP domes use a standard Ethernet connection to provide video and control to a software application, such as GE’s SymSecure or SymNav. When used in an analog system, Legend IP domes also include analog video and data connections, along with the network connection. You can mix analog Legend and digital Legend IP domes in the same system.

Legend IP domes can be operated from keypads, in addition to digital video management software. The housings have Ethernet, RS-485, and RS-422 connections for data control, and Ethernet, UTP, and coaxial connections for video. The Ethernet cable provides both video and communication data. The network interface is 10/100/Base-T Ethernet compliant and supports TCP/IP communication protocols on private networks, intranets, and the Internet.

GE’s SymSecure digital video management software offers many ways to complete tasks so as to accommodate the various ways that people are comfortable working. The documentation for Legend IP will provide one basic method for each basic task described. For complete usage instructions for SymSecure, refer to the SymSecure online help. If you are using SymNav or another compatible digital video management tool to operate your Legend IP domes, refer to that software’s documentation for its instructions.

Page 11

Chapter 1

Introduction

Cameras operate using the housing's memory, since programming is now stored in the housing. This allows you to replace cameras or move them between housings without having to reprogram them for each new site.

Note: Be aware that the installer through the Installer passcode may have turned on passcodes during installation to protect

the dome against unauthorized access. Using passcodes is optional, however. They are off by default. For details, see

Passcode page on page 35.

Figure 1. Main menu of the graphical programming interface

System configurations

Digital Legend IP domes can be used in a variety of digital and analog system configurations. They have both digital and analog connections for video and data. They also still maintain their built-in receivers that decode analog commands originating from a compatible controlling devices, such as a keypads or ASCII control software. See Operational overview on page 2.

Page 12

Legend IP

User Manual

Typical digital system

A typical digital system is shown in Figure 2. In this configuration, control commands come from a software application, such as GE’s SymSecure or SymNav, instead of keypads or ASCII control software. The dome’s built-in encoders stream video to external decoders before it is transmitted to monitors, digital recorders, and alarm equipment. For additional details, refer to the data sheet, user manual, or application guide.

Figure 2. Typical digital system in an IP codec network

Legend

SymNet

Ethernet

decoder

Ethernet

Network

Coax analog line

CCTV monitor

Legend

Ethernet

KTD-405

Ethernet

Network

Client PC with SymNav. Used for setup and control.

Page 13

Chapter 1

Introduction

Typical advanced analog system

A typical advanced analog system is shown in Figure 3. In this configuration, control commands pass through digital recorders and alarm equipment and video is switched to various monitors. For additional details, refer to the data sheet, user manual, or application guide.

Figure 3. Typical advanced analog system

Digital recorder

Video

loop-

through

N/O COM

N/C

Matrix switcher

Mon 1 Mon 2 Mon 3 Mon 4

Data distributor

SWITCH BIAS

REMOVABLE

TERMINAL STRIP

POWER

12 VDC

EARTH GROUND

RS485 B

RS422 IN B

RS422 OUT

78910653214

SPEAKER SHIELD

AUDIO KEYPAD RS485 RS485

SPEAKER

Controller

keypad

SWITCH BIAS

REMOVABLE

TERMINAL STRIP

POWER

12 VDC

EARTH GROUND

RS485 B

RS422 IN B

RS422 OUT

78910653214

SPEAKER SHIELD

AUDIO KEYPAD RS485 RS485

SPEAKER

Controller

keypad

Alarm input

module

Alarm chassis

Alarm inputs

Dome

Local alarm

inputs

(dry contacts)

Local relay

outputs

1 8

Alarms/relays

Video

RS-422 data

RS-485 data

Page 14

Legend IP

User Manual

Typical basic analog system

A minimum of one keypad, which is the most common controlling device, is required for operation. See Figure 4. From the keypad, an operator can pan, tilt, and zoom the camera, find presets, and start macros and ShadowTours.

Figure 4. Basic analog system

SWITCH BIAS

REMOVABLE

TERMINAL STRIP

POWER

12 VDC

EARTH GROUND

RS485 B

RS422 IN B

RS422 OUT

78910653214

SPEAKER SHIELD

AUDIO KEYPAD RS485 RS485

SPEAKER

Typical mixed analog/digital system

A typical mixed analog/digital system is shown in Figure 5. In this configuration, control commands come from either software applications or keyboards or ASCII control software. Video is encoded and sent through the network to a SymSecure server, client PC, or to a SymNet decoder for display on a CCTV monitor. For additional details, refer to the data sheet, user manual, or application guide.

Figure 5. Mixed analog/digital system

Legend

Legend IP

SymDec

SymVeo

Network

SymNet

SymSecure server

CCTV monitor

KTD-405

SymSecure client PC with USB joystick controller

SCSI RAID storage

Page 15

Chapter 1

Introduction

Available protocols

Tab le 1 lists the protocols that can be assigned to each dome with the rotary protocol switch that is located on the active housing card (AHC) in the dome’s housing. Be aware that the available protocols and their settings have changed since the early analog Legend domes.

Refer to the Legend IP Installation Manual (1055712) for instructions on setting the protocol.

Table 1. Protocol switch assignments

Setting Protocol

0 Digiplex (RS-422) @ 4800 baud

1 Kalatel (RS-485) @ 9600 baud

2For future use

3For future use

4For future use

5 ASCII (RS-422) @ 9600 baud

6For future use

7 Ultrak @ 9600 baud (even parity)

8 Pelco P @ 4800 baud

9 Pelco D autobaud @ 2400, 4800, and 9600

A Tyco/AD (RS-422) @ 4800 baud

BFor future use

CFor future use

DFor future use

EFor future use

FFor future use

Page 16

Legend IP User Manual

Page 17

Chapter 2 Accessing the programming

interface

This chapter provides instructions for accessing the dome’s programming menus from a computer or keypad.

In this chapter:

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Computer versus keypad access. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

When is logging on necessary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Multiple users. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using a keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Page 18

Legend IP

User Manual

Overview

Now that users can access a dome’s programming menus over a network, you need to understand what is different about using a computer versus a keypad, when is logging in necessary, and how are multiple users handled. See the following sections.

Computer versus keypad access

From a computer, you can use the web-based version of the graphical programming interface, or from a keypad, you can use the analog graphic menu version on a security monitor. Both step through the same programming menus. Both record changes instantly.

When is logging on necessary

If passcodes were turned on (that is, specified) during installation or later, access to the programming interface will be passcode-protected and you will have to log on to the dome to program it. Otherwise, you will be taken directly to the main programming page from the web browser or keypad without the need to enter a passcode. The passcodes control who has access to the features of your dome. See Passcode page on page 35.

Multiple users

Multiple users can access the programming menus from different locations (computers and/or keypads) and the dome will process programming changes in the order they are received. Any conflicting changes will be responded to with an error message.

Using a computer

When you are using a computer to access the dome’s graphical programming interface, you will be using a web browser. SymNav cannot access the programming menus. You can access the programming menus and video using Internet Explorer 6.0, or higher. The browser cannot control the camera unless Java computer, however. If you do not already have Java installed on your computer, go to www.java.com and download it now.

To access the programming interface using a web browser:

1. At the computer’s desktop, double-click the web browser icon.

2. Type the camera’s IP address into the address field in the form of http://xxx.xxx.xxx.xxx (where xxx.xxx.xxx.xxx is the IP address of your camera). The default IP address will be provided by the installer.

The video and control screen will appear (Figure 6 on page 11).

is installed on your

Page 19

Figure 6. Video and control screen in Internet Explorer

Accessing the programming interface

Chapter 2

3. Click the link labeled Video to bring up the login box. For the User name, select the operation mode requested. This can be either Administrator, Installer, or Operator. If passcodes are enabled, the password is the 4-digit passcode. If passcodes are disabled, leave the password blank.

4. The Legend IP video screen appears (Figure 7). To enter the GUI select the Enter GUI button in the upper left corner. Use the mouse to select controls and buttons from the camera configuration GUI.

Figure 7. Login screen of Internet Explorer

Page 20

Legend IP

User Manual

Web interface

You can control many of the features of the Legend IP from the web interface. The interface contains various status and configuration controls that are easily available.

Logs

This page contains information concerning the operation of the camera. The data is meant for technical support, if problems arise.

Network

The link allows configuration of the network. The settings available on this page are the same as those detailed in Network page on page 38 (Figure 8).

Figure 8.

Page 21

Accessing the programming interface

Chapter 2

Encoder

This link allows you to configure the video encoder settings. The settings available on this page are the same as those detailed in Encoder page on page 56 (Figure 9).

Figure 9.

Page 22

Legend IP

User Manual

Video

The video tab allows you to view and have basic control of the camera. The camera controls are designed for troubleshooting and should not be used for regular use. On the left is a control with directional buttons. The camera speed is controlled by the Camera Speed slider.

Additionally, there are controls for zoom, focus, and iris manipulation.

You can also store and select presets with the button on the bottom of the video page (Figure 10).

Figure 10.

Page 23

Accessing the programming interface

Chapter 2

Info

This tap displays the state of the camera. It is an easy way to view and administer configurations (Figure 11).

Figure 11.

Update

This tab is used for the updating of the camera’s firmware.

Page 24

Legend IP

User Manual

Using a keypad

The steps for accessing the programming interface from all GE keypads are similar. The following procedure is based on the KTD-405 keypad, which is currently GE’s most popular keypad. Exceptions to the procedure for other GE keypads are noted. You can also use the GE KTD-400 and KTD-404/304 keypads and other manufacturers’ keypads and controllers using the Pelco D (autobaud), Pelco P, Tyco/AD (RS-422), Ultrak, Impac (RS-485), and ASCII protocols. When using these other protocols, all standard commands are supported by the Legend IP protocol, including pan, tilt, lens (zoom, focus, and iris), preset, and joystick control commands for the specified third-party protocols. For details, see Compatible protocol commands on page 117.

To access the programming interface from a KTD-405 keypad:

1. At the normal display, press and hold the set

(  ) key on the keypad until you hear a beep and the programming code display appears on the keypad’s LCD.

2. At the ENTER PROGRAMMING CODE

display, enter the programming access code by pressing the 9, 5, 1, and seq keys.

This code is the same for all GE keypads.

3. At the equipment selection display, press 3 to

select CAMERA (keypad v1.2.09 or later) or CAMERA/RCVR (keypad v1.1.06 or earlier).

If you have an older keypad (v1.1.06 or earlier), you will have a second equipment selection display, at which you need to press 1 for CYBERDOME.

Figure 12. Normal display (programming interface accessed)

CAMERA 1 MONITOR 1

Figure 13. ENTER PROGRAMMING CODE display

ENTER PROGRAMMING CODE: _

Figure 14. Equipment selection display

1=SWITCHER/MPLX 2=ALARMS 3=CAMERA EXIT

1=SWITCHER/MPLX 2=ALARMS 3=CAMERA/RCVR EXIT

1=CYBERDOME 2=PTZ 3=AUXILIARY



BACK

v1.2.09 or later

}

v1.1.06 or earlier

4. At the ENTER CAMERA SITE NUMBER

display, enter the number for the camera site you are programming. This is a 3-digit number (for example, 007, 021, 243).

You can enter one, two, or three digits and press set (  ).

Figure 15. ENTER CAMERA SITE NUMBER display

ENTER CAMERA SITE NUMBER ___

BACK

Page 25

Accessing the programming interface

Chapter 2

5. Continue entering commands with the joystick.

Figure 16. SEE MONITOR FOR MENUS display

SEE MONITOR FOR MENUS HOLD SEQ (3 SEC) TO EXIT

6. If passcodes are turned on, they are required. Select your passcode level and enter your passcode (Figure 17). You will be taken to the main programming page. If passcodes are turned off, they are not required and you will be taken directly to the main programming page.

From the main programming page, you can access any programming parameters that are allowed by your passcode.

Figure 17. Log on (if passcode required) and main programming pages

Page 26

Legend IP User Manual

Page 27

Chapter 3 Programming tools

This chapter provides instructions for how to use the keypad joystick and graphical programming interface to program domes.

In this chapter:

Web based controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Joystick modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Joystick as simulated mouse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Joystick as PTZ controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Using the graphical keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Inactivity timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Keypad shortcuts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Page 28

Legend IP

User Manual

Web based controller

The web-based controller is a java applet stored on the camera. This applet will provide basic PTZ control similar to what you would expect with a KTD-405 keypad.

Figure 18. Web based controller

Camera IP. This is the IP address of the camera you are currently viewing.

Camera speed. This control will adjust the speed of the Up, Down, Left and Right buttons below the

slider. The range is 0 (slowest/off) to 31 (fastest)

Up, Down, Left and Right. Pan and Tilt the camera.

Zoom +/-. Zoom the camera in (+) and out (-).

Focus +/-. Focus the camera for close objects (+) or distant objects (-).

Iris +/-. Increase Iris f-stop (+) or decrease Iris f-stop (-).

Set. Used while in menus to accept a selection.

Esc. Used while in menus to cancel or clear a selection.

Index. Preset or Tour value selected

Auto pan. Send the Auto pan request command to the camera.

Page 29

Programming tools

Chapter 3

Shadow tour. Used in conjunction with the Index value to select a Shadow tour. For example, if the index

is on 15 and the Shadow tour button is pressed the camera will begin Shadow tour 15 (if programmed).

Preset store. Used in conjunction with the Index value to store a preset.

Preset find. Used in conjunction with the Index value to select a preset.

Joystick modes

While you are in the graphical programming interface, the joystick of your keypad operates in two modes depending upon what your current action is. While moving among the menus of the programming interface, the joystick is a simulated mouse and you enter commands using the joystick. While controlling live video, the joystick is a PTZ controller. So, whenever you are positioning titles or privacy masks, or programming live video features such as presets and ShadowTours, the joystick is a PTZ controller, in which case, you will use the keypad’s keys to enter commands.

Joystick as simulated mouse

When the joystick is simulating a mouse within the programming interface, it can move the cursor, move a title, or make a selection in the menus.

Moving the cursor or a title

To move the cursor (onscreen arrow) across the menus, or to move a title across the screen during title positioning, push or pull the joystick in any direction. The farther you move the joystick, the faster the cursor will move. If your keypad doesn’t have a joystick, directional keys will have the same effect.

Making a selection

To make a selection in the menus, place the cursor over a menu, button, checkbox, item in a list, or arrow of a drop-down box by pushing or pulling the joystick in any direction, then twist the knob on the joystick.

Figure 19. Twisting the joystick knob to make selection

You can also use the zoom+/- key on the keypad to make selections.

Joystick as PTZ controller

When the joystick is controlling the PTZ movements of the camera within the programming interface, use the keypad’s keys to enter the save and cancel programming commands.

Page 30

Legend IP

User Manual

Saving live video programming

To save live video programming, such as positioned titles, privacy masks, presets, and ShadowTours, press the iris + or the set (  ) key on the keypad.

Canceling live video programming

To cancel live video programming, such as positioned titles, privacy masks, presets, and ShadowTours, press the iris - or the esc key on the keypad.

Page 31

Programming tools

Chapter 3

Using the graphical keyboard

The programming interface has an internal graphical keyboard for entering passcodes, network data, and custom titles. Open the graphical keyboard (Figure 20) by selecting the icon necessary characters, select Done on the keyboard or press the set (  ) key on the keypad to return to the page. Then select OK to save the changes made to the page. Pressing esc on the keypad while you are still in the keyboard erases the characters shown. You must select OK or Cancel to save or cancel the changes entered on the page.

Figure 20. Using the keyboard of the programming interface

1. After you have entered the

1 Select the ab icon to

open the keyboard.

2 Select the Done icon to

close the keyboard.

3 Select the OK icon to save

changes to the page.

Inactivity timer

The programming interface has a 10-minute keypad inactivity timer. When being used with keypads that do not have their own inactivity timer, the programming interface will time out after 10 minutes of inactivity. When being used with keypads that do have their own inactivity timer and it is less than the 10-minute timer of the programming interface, the programming interface will time out when the keypad does. When being used with keypads that have a longer inactivity timer, the programming interface will time out after 10 minutes of inactivity. Refer to your keypad’s manual to see if it has an inactivity timer and what the duration is so that you know when you can expect the programming interface to time out.

Page 32

Legend IP

User Manual

Keypad shortcuts

The following are keypad shortcut commands carried over from CyberDome programming. Where keypad shortcuts exist for a feature, such as setting presets, you can use keys from the keypad, instead of menus from the programming interface, to program the feature. See Ta bl e 2. You can then go into the programming interface and customize the programmed feature with titles and other attributes.

Table 2. Keypad shortcuts

Command Keypad shortcut

Set a preset store | (number) | store

Note: Storing presets with the KTD-400 or

Set the left autopan limit

Set the right autopan limit

For details, see the KTD-405 Controller Keypad User Manual (1036547).

 | store

store |

Note: On the KTD-400 or KTD-404, move

 | store

store |

Note: On the KTD-400 or KTD-404, move

KTD-404 must be done using the Legend IP analog interface.

the camera to the limit, press and hold the Zoom In and Zoom Out buttons, and press the pan button (KTD-400) or the joystick (KTD-404) in the direction of the limit.

See Autopan limitations on page 99 for restrictions for setting autopan limits.

Page 33

Chapter 4 Basic programming

This chapter provides instructions for establishing network connectivity with the dome and instructions for programming the most commonly used dome operations (presets and ShadowTours). The dome is otherwise ready to operate using its defaults. If you want to customize the dome’s programming for advanced surveillance applications, go to Advanced programming on page 33.

In this chapter:

Establishing network connectivity with the dome. . . . . . . . . . . . . . . . . . 26

Addressing the dome and the network . . . . . . . . . . . . . . . . . . . . . . . 26

Setting the encoder ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Presets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Programming presets from the keypad. . . . . . . . . . . . . . . . . . . . . . . 29

Programming presets with the programming interface . . . . . . . . . . 29

Programming presets with the web interface. . . . . . . . . . . . . . . . . . 30

ShadowTours. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Page 34

Legend IP

User Manual

Establishing network connectivity with the dome

All of the settings for the dome and the dome’s encoder, need to be coordinated so that all components communicate properly in the network to transmit video and data. This section provides instructions for addressing the dome, the network, and setting the encoder.

The following procedures are using the Internet Explorer web browser. The steps are similar with other browsers.

Addressing the dome and the network

The Network page establishes the IP addressing for the dome and other network components that allows you to transmit video and data digitally across an IP network. There are three tabs on the Network page. You must program the features on the IP tab to ensure connectivity. You may customize the features on the NTP and Email tabs, but the dome will operate with the default settings. See Network page on page 38 if you want to customize these default settings..

CAUTION: To ensure the security of your surveillance system, your IP network should be isolated and secured from

unauthorized access.

To access the Network page, select Setup and Network.

Figure 21. Network page

Be sure to work with your network administrator while establishing the network connectivity of your domes.

To program the network settings, see Figure 21 and do the following:

1. At the DHCP Enabled feature, place a checkmark in the checkbox if you are using dynamic addressing.

The Dynamic Host Configuration Protocol (DHCP) allows the network to assign a different IP address to the dome each time it connects to the network. This protocol also allows a mix of static and dynamic

Page 35

Basic programming

Chapter 4

IP addressing. The host name, domain name, and DHCP timeout features are only available when you enable this feature.

2. At the IP address feature, enter the static IP address of the dome. The dome ships with the default IP address of 192.168.1.2. Whether you will be using static or dynamic addressing for your system, do assign an initial static IP address for the dome. If you are using DHCP, this will be the backup IP address.

3. At the Net mask feature, enter the IP address of the subnet mask of the network subdivision that the dome is assigned to.

4. At the DNS server feature, enter the IP address of the network domain name server.

5. At the Gateway feature, enter the IP address of the gateway between the dome and the network server.

6. At the Host name feature, enter the name of the camera on the network. This feature is not available if the DHCP Enabled feature is not checked.

Note: This is only used when DHCP is enabled.

7. At the Domain name feature, enter a domain name. This feature is not used with DHCP.

8. At the DHCP timeout feature, choose between 1 minute, 2, 5, 10, 20, and 30 minutes. This feature is not available if the DHCP Enabled feature is not checked.

9. At the MAC address feature, do nothing. It is provided as a unique hardware address for the dome. It allows you to connect to the dome before you have set up its network addressing. The MAC address is assigned at the factory. The installer establishes the overriding IP address during installation.

Note: Any changes to the Network settings will require a reboot for the settings to take effect.

Setting the encoder ports

The Encoder page establishes the control and multicast ports that are required to complete network connectivity for the dome. There are two tabs on the Encoder page. You must change the features on the Control tab. You may customize the features on the Video tab, but the dome will operate with the default settings.

To access the Encoder page, select Camera and Encoder.

Page 36

Legend IP

User Manual

Figure 22. Encoder page

Be sure to work with your network administrator while establishing the network connectivity of your domes.

The default settings on the encoder control settings are the following (Figure 22 on page 28):

Table 3.

Setting Default

Enable network port Checked

Listen port 1024

Control port 9000

Streaming mode Sender

Streaming address 230.0.0.0

Streaming port 8090

Sender control port 8092

Receiver control port

Enable auto discovery Checked

1. This control will be removed in future releases.

8092

Page 37

Basic programming

Chapter 4

Presets

You can set presets from the keypad or with the graphical programming interface. If you set your presets from the keypad, you may want to go into the programming interface to customize them with titles and exposure settings. Programming presets with the KTD-400 or KTD-404 must be done using the Legend IP onscreen programming interface.

There are a total of 127 presets (1 through 127) that you can define for your dome.

The dome also provides the ability to remap any preset or tour command to activate any of the 127 presets, 16 tours, or 32 macro actions. This enables you to manually initiate any of the expanded capabilities of the dome from keypad controllers with limited command capability. See Command Map page on page 85.

Note: Most keypads have a limited number of preset numbers they can call. If you have a GE KTD-405 keypad with firmware

v1.2.09 or later, and it is operating with Impac RS-485 protocol, then you can call up all 127 preset numbers (1 through

127) directly from the keypad. If, however, you have a GE KTD-405 keypad with an earlier version of firmware, or it is operating with Digiplex RS-422 protocol, then you can use the keypad to call up only the first 63 preset numbers (1 through 63). If you are using presets 62 and 63 for your left and right autopan limits, then you have a total of 125 or 61 preset numbers that you can call up from the keypad. To verify your keypad’s version, press and hold the mon key on the keypad, until the keypad beeps, then press the >> key.

Programming presets from the keypad

To program presets from the KTD-405 keypad, do the following:

1. Use the joystick to pan, tilt, and zoom the camera to the desired view.

2. Press store on the keypad.

3. Press the number keys on the keypad that correspond to the preset number you want to assign for this position.

4. Press store again.

Note: If the keypad does not allow you to program a desired preset, you may need to change the lowest user-

definable preset in the keypad program menus. Refer to the keypad manual.

5. After programming your presets, you can verify them, one at a time, by pressing the find key on the keypad and then pressing the number keys that correspond to each preset. If you are not satisfied with any views, you can reprogram those preset positions starting with step 1 above.

6. If desired, go into the programming interface to customize the preset with a title and exposure settings. See Presets page on page 59.

Programming presets with the programming interface

To program presets with the programming interface, do the following:

1. Access the programming interface. See Accessing the programming interface on page 9.

2. Select Actions by guiding the joystick to move the cursor over the Actions menu and twisting the joystick knob.

Page 38

Legend IP

User Manual

Figure 23. Preset programming page

3. Select Presets.

4. Select the Edit tab.

5. Select a preset number.

6. Select Program.

7. Use the joystick to pan, tilt, and zoom the camera to the desired view.

8. Press the iris+ or set (  ) key on the keypad to save the preset position or press the iris- or esc key to

cancel the preset position. Both canceling and saving the preset position returns you to the Edit page.

9. After you have saved a preset position, then you can use the features on the Edit, Display, and

Advanced tab pages to customize the preset’s title, duration, and exposure settings. See Presets page on page 59.

Programming presets with the web interface

To program presets with the web interface, do the following:

1. Start the web interface and log in. See Using a computer on page 10.

2. Use the onscreen directional buttons to pan, tilt, and zoom the camera to the desired view.

3. Set the Index slider bar to the desired number.

4. Press the Preset store button to assign that position to the preset number.

Page 39

Basic programming

Chapter 4

ShadowTours

You have a total of 16 ShadowTours (totaling 20 minutes) that you can define for the dome. A ShadowTour is a tour that the camera learns by recording your manual operation of the camera. Use a keypad to manually direct the camera through the desired PTZ movements. The camera stores those movements in memory. The recorded tour can be replayed at any time.

To program ShadowTours with the programming interface, do the following:

1. Access the programming interface.

2. Select Actions by guiding the joystick to move the cursor over the Actions menu and twisting the joystick knob.

Figure 24. ShadowTour programming page

3. Select ShadowTours.

4. Select a ShadowTour number.

5. Select Program.

6. Press and release the set (  ) key on the keypad to start the ShadowTour timer.

7. Use the joystick to manually direct the camera through the desired PTZ movements

8. Press the iris+ or set (  ) key on the keypad to save the ShadowTour or press the iris- or esc key to cancel the ShadowTour. Both canceling and saving the ShadowTour returns you to the ShadowTour page.

9. After you have saved a ShadowTour, then you can use the features on the ShadowTour page to customize the tour’s title. See ShadowTours page on page 66.

10. After programming your tours, you can verify tours from within the programming interface by selecting a tour number and Show.

Page 40

Legend IP User Manual

Page 41

Chapter 5 Advanced programming

This chapter provides instructions for customizing the dome’s programming for advanced surveillance applications. You will be using the graphical programming interface. You can access it from either a computer or a keypad (Accessing the

programming interface on page 9). From a computer, you will be accessing the

web-based version, and from a keypad, you will be accessing the OSD (onscreen display) version. Both step through the same programming menus. Keypad shortcuts do exist for some programmable features (Keypad shortcuts on page 24), if you prefer to use them. Shortcuts can be quicker when setting a large number of preset positions, but you will use the programming interface to customize such features as exposure settings.

In this chapter:

Confirming settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Camera menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Actions menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Alarms menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Control menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

System menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Page 42

Legend IP

User Manual

Confirming settings

When changing settings on any programming page, you need to confirm the new settings by selecting OK on that page. When establishing live video settings (for example, ShadowTours), you need to save the live video settings (by pressing the iris + or the set (  ) key on the keypad), then save the changes made on the programming page (by selecting OK in the programming interface) when you return to programming mode from live video mode.

Setup menu

This is the beginning of your system’s setup. Start here to title your dome, turn on/off or change passcodes, establish network connectivity, set the north point, and manage your dome’s memory.

Figure 25. Setup menu

Memory page

Programming and addressing for the dome are stored to the housing. Having the memory stored in the housing allows you to replace cameras or move them between sites without having to reprogram cameras for each new site, because the camera will operate using the housing memory.

The Memory page allows you to manage your dome’s memory during setup and operation. When you clear part or all of your dome’s memory, you are overwriting your custom programmed settings with the factory default settings.

Page 43

To access the Memory page, select Setup and Memory.

Figure 26. Memory page

Advanced programming

Chapter 5

CAUTION: Clearing memory replaces your custom programmed settings with the factory default settings.

Select memory. You can clear all or specific portions of your dome’s programming, which is saved in the

housing’s memory. After selecting a setting, select Clear. Choices are Clear all (default), Clear setup options, Clear presets, Clear macros, Clear ShadowTours, Clear areas, Clear alarm actions, and Clear privacy masks.

Note: Clear all clears all settings, except passcodes, installation date, IP address and subnet mask.

Passcode page

You can control who has access to the features of your dome by distributing passcodes that allow varying degrees of access. The dome ships with no default passcodes. When you enter the programming interface for the first time during installation and go to Setup | Passcode, the passcode fields are blank. Blank passcode fields mean the passcodes are turned off (disabled). You can choose to enter passcodes into the blanks. This turns passcodes on (enabled) and a passcode will be required to enter the programming interface the next time you access it.

CAUTION: If you use passcodes, record them in a secure place. If you forget the passcodes for a dome, you will need to

If no passcodes are programmed, all users are given installer access and are not required to log on. If only the Admin and Operator passcodes are programmed, then anyone can still access the entire programming interface as an installer, since the Installer passcode is not programmed.

send the dome back to the factory so that it can be reset with no passcodes.

Page 44

Legend IP

User Manual

You can turn on one installer passcode, one admin passcode, and one operator passcode. They have the following permissions:

• Installer: The installer passcode allows access to all dome features.

• Admin: The admin passcode allows access to all dome features, except passcodes and firmware

upgrades.

• Operator: The operator passcode allows no access until it is granted access to specific features on an

area-by-area basis.

To access the Passcode page, select Setup and Passcode.

Figure 27. Passcode page

Note: Remember to select OK to save any changes you make on the page.

Installer passcode. The Installer passcode feature allows the installer to operate and change all dome

features, including all three default passcodes (installer, admin, and operator). There is a 4-digit limit.

Admin passcode. The Admin passcode feature allows your system administrator to operate and change all

dome features, except passcodes and firmware upgrades. There is a 4-digit limit.

Operator passcode. The Operator passcode feature allows the operator to operate and change only

those dome features that have been enabled for the operator passcode. There is a 4-digit limit.

Operator access options. The Operator access options feature allows the installer to choose which

features an operator has access to operate and change. Choices are as shown onscreen.

Page 45

Advanced programming

Title/Date page

The Title/Date page establishes the camera number, title, and installation date for the dome.

To access the Title/Date page, select Setup and Title/Date.

Figure 28. Title/Date page

Chapter 5

Note: Remember to select OK to save any changes you make on the page.

Camera number. The programming interface reads the address number set in the camera with the rotary

address switches and displays that address as the camera number. The camera number is not editable.

Camera title. The Camera title box allows you to give each camera a unique title. There is a 60-character

limit for all titles, but be aware of how much video you want to cover with your titles.

Display title. The Display title feature enables or disables the display of individual camera titles on the

monitor screen. Choices are On (default) and Off.

Title POS. The camera title will appear on screen in a default position on the monitor screen (upper

center), but you can reposition it with the Title POS button. Be aware of where you already have other titles (privacy masks, presets, tours, macros, areas, and alarms) positioned.

To set the position of the camera title:

1. Select Title POS.

2. Use the joystick to move the title to the desired position.

3. Press the iris + or the set (  ) key on the keypad to save the new position or press the iris - or

the esc key to cancel the new position.

Title font color. The camera title will appear on screen in the color selected. Choices are as shown

onscreen. Default is White.

Title font size. The camera title will appear on screen in the font size selected. Choices are as shown

onscreen. Default is 14 pt.

Page 46

Legend IP

User Manual

Title font weight. The camera title will appear on screen in the font weight selected. Choices are as

shown onscreen. Default is Bold.

Block color. You can create a block (background) that offsets the camera title from the video behind it.

The block will appear on screen in the color selected. Choices are as shown onscreen. Default is Black.

Block transparency. You can set the block (background) to be a solid color or a transparency. The block

will appear on screen in the transparency selected. Choices are as shown onscreen. Default is No color.

Installation date. Enter the actual date of installation for your camera. Include the punctuation in the

format shown onscreen.

Network page

The Network page establishes the IP addressing for a network connection that you can use to flash software upgrades over a standard IP connection to the dome via its Ethernet connection.

CAUTION: When flashing software upgrades to the dome over a standard IP network via the dome's Ethernet

connection, ensure that the network is secured from unauthorized access. Consider connecting the Ethernet cable only when you are flashing the dome, unless you have the dome connected to a secure, isolated network.

To access the Network page, select Setup and Network.

IP page

The IP page contains the following options.

Figure 29. Network page

DHCP. Dynamic host configuration protocol is used by client computers to retrieve and assign IP

addresses, networking information and other configurations. If no IP address is found, it will default to the IP address stored in the active housing. If there’s no IP address found in the active housing, it will

Page 47

Advanced programming

Chapter 5

default to 192.168.1.2. There is no DHCP server supplied with the Legend IP. With DHCP enabled, you can still specify an IP address.

Dome IP address. Enter the IP address of the dome. The IP address is associated with the camera itself,

not the housing.

Net mask. Enter the subnet mask address of the network subdivision that the dome is assigned to. This is

assigned by your network administrator.

DNS Server. Enter the IP address of the DNS server. This is necessary for hostname resolution.

Gateway. Enter the address of the gateway or router between the dome and the network server. This is

assigned by your network administrator.

Host name. The name of the camera on the network. The host name is greyed out if DHCP is not enabled.

Domain name. This is a domain suffix that is added to the end of the domain name for network

identification.

DHCP timeout. The amount of time before the housing stops trying to retrieve an IP address. If no IP

address is supplied, there is no network connectivity.

TCP MTU. The packet payload size used with TCP protocol. Possible selections are 1514, 1400, and

1200 bytes per packet. In some cases, you’ll receive the best performance with more bytes per packet. Some wireless transmissions perform better with smaller packets. Consult your network administrator to determine the best setting.

MAC address. Provided as a unique hardware address for the dome, the MAC address allows you to

figure out the IP address of the dome. It can also help with DHCP based IP addresses.

The MAC address is assigned at the factory to a default value which can be restored by selecting the Restore factory MAC button.

Additionally, you can edit the MAC address to meet certain installation requirements. If you edit the MAC address field, the new address will be used. In situations where an exact clone of a dome is needed, editing the MAC address is useful. Otherwise we recommend you use the factory default.

Note: The MAC and IP addresses are stored in the PTZ unit, not in the housing. Be aware of that when you swap

cameras around.

Page 48

Legend IP

User Manual

NTP page

The NTP page contains the following options:

Figure 30. NTP page

Enable NTP. Enable the frequency at which you would like to synchronize your Legend IP with a clock.

If NTP is enabled, serial time sync will be disabled.

NTP server. Enter the address of the NTP server.

Backup server. Enter the address of the backup NTP server.

Timezone. Choose your timezone in GMT with time differential.

Daylight savings. Choose off, or the area the camera is in (USA, Europe, or Australia).

Page 49

Email page

The email page has the following options:

Figure 31. Email

Advanced programming

Chapter 5

Email server. Enter the address of the email server.

SMTP port. Enter the SMTP port. The default is 25.

To. Enter the address of the email’s recipient. This is the TO: address in a normal email from you.

CC. Enter the address of a backup email recipient.

From. Enter the address of the email’s sender. This is the FROM: address in a normal email from you.

Messages. Pick from 10 preformatted messages. Or you can customize them to fit your needs with

variables specific to certain pieces of data. Each message is configurable to a maximum of 64 characters before the variables translate into the data. Select the AB button to enter text for the message body.

Table 4. Email variables

Variable Data

%a Shows alarm status block.

%A Shows alarm status in XML format.

%c Shows camera number (the address switches).

%n Shows the camera name.

%C Show siteIdentifier XML

Page 50

Legend IP

User Manual

Table 4. Email variables

Variable Data

%N also siteIdentifier.

%d Shows the date as YYYY-MM-DD.

%D The date as dd Month YYYY.

%f Shows far end configuration (not implemented).

%i Shows the index. Used in macro, preset, etc titles.

&l Shows the length or number of steps for tours, macros, etc.

%o Shows the origin (not implemented).

%p Shows the protocol address.

&r Shows the release version string.

%T Shows time as HH:MM:SS.

%t Shows time as HH:MM.

%u Shows user identifier.

%v Shows video parameters in XML.

%% Prints a percent sign.

%\ Prints a “\”.

\% Prints a percent sign.

\\ Prints a “\”.

\n New line.

\r Line feed.

\c Return

\t Tab.

For example, if the date was 12/04/2007, the time was 10:24:33, the camera’s title was “Back Door”, and an alarm 3 was attached to a door switch that was triggered, the email message would originally look like:

The alarm %a was triggered on %d at %t on camera %c.

But the final email would look like:

The alarm 3 was triggered on 12/04/2007 at 10:24:33 on camera Back Door.

Page 51

Advanced programming

Chapter 5

Preferences page

The Preferences page establishes the systemwide features of language and the display of the camera’s spatial coordinates.

Display page

To access the Display page, select Setup, Preferences, and Display.

Figure 32. Display page

Note: Remember to select OK to save any changes you make on the page.

Language. The Language feature sets which language the programming interface uses to display its

content and your entries. Choice is English.

Branding. The Branding feature displays GE branding during product demonstrations. Choices are Off

(default) and On.

Temperature display. The Temperature display feature sets which unit is used to display the current

operating temperature for the dome on the monitor screen. Choices are Off (default), Celsius, and Fahrenheit. If Off is selected while the high and low thresholds are being used and are exceeded, the Off selection will default to Celsius.

High temp warning. The High temp warning feature allows you to display a high-temperature reading on

the monitor screen when the temperature in the dome has reached a set high threshold. Place a checkmark in the checkbox to display this warning. The threshold and duration features then become available.

Threshold (high-temp). The high-temperature Threshold feature allows you to set the high boundary of

the allowable temperature range for the dome. Choices are in 10-degree increments. Default is 0.

Duration (high-temp). The high-temperature Duration feature allows you to set how long the warning

appears on the monitor screen. Choices are During action (default) and Indefinite.

Page 52

Legend IP

User Manual

• During action: Displays the temperature warning only while the temperature is above the threshold.

• Indefinite: Displays the temperature warning even after the temperature drops below the threshold.

Low temp warning. The Low temp warning feature allows you to display a low-temperature reading on

the monitor screen when the temperature in the dome has reached a set low threshold. Place a checkmark in the checkbox to display this warning. The threshold and duration features then become available.

Threshold (low-temp). The low-temperature Threshold feature allows you to set the low boundary of the

allowable temperature range for the dome. Choices are in 10-degree increments. Default is 0.

Duration (low-temp). The low-temperature Duration feature allows you to set how long the warning

appears on the monitor screen. Choices are During action (default) and Indefinite.

• During action: Displays the temperature warning only while the temperature is below the threshold.

• Indefinite: Displays the temperature warning even after the temperature rises above the threshold.

Coordinates page

You can display the dome’s pan, tilt, or zoom coordinates on the monitor screen, if desired. You can display any or all of the coordinates. You can also choose how to display each one.

To access the Coordinates page, select Setup, Preferences, and Coordinates.

Figure 33. Coordinates page

Note: Remember to select OK to save any changes you make on the page.

Pan. The Pan feature displays the pan coordinate of the dome. Choices are Off, Bearings (compass

directions, such as N, NE, E), Degrees 360 (default), and Degrees ± 180.

Page 53

Advanced programming

Tilt

Chapter 5

Figure 34. Pan coordinates

Pan coordinates:

Units: Bearings/Degrees 360°/Degrees ±180°

Bearings/Degrees 360°/Degrees ±180°

N/0°/0°

NW/315°/-45°

W/270°/-90°

W/270°/-90° E/90°/+90°

SW/225°/-135°

S/180°/+180°

NE/45°/+45°

NE/45°/+45°NW/315°/-45°

SE/135°/+135°

SE/135°/+135°SW/225°/-135°

E/90°/+90°

Tilt. The Tilt feature displays the tilt coordinate of the dome. Choices are Off, Degrees 180 (default), and

Degrees +/- 90.

Figure 35. Tilt coordinates

Units: Degrees 180°/Degrees ±90°

0°/+90°

0°/+90° 180°/-90°

coordinates:

Degrees 180°/Degrees ±90°

N/270°/-90°

NE/225°/-135°NW/315°/-45°

180°/-90°

135°/-45°

135°/-45°45°/+45°

Negative (-) hemisphere

Positive (+)

hemisphere

45°/+45°

90°/0°

Zoom. The Zoom feature displays the zoom coordinate of the dome. Choices are Off and Power (default).

Set north. The Set north button programs the north (0°) pan point for the camera.

Note: When using bearings for your pan coordinates, they are easier to interpret if you set the true due north point

as the 0° point. If, however, you are using degree pan coordinates, you can set the 0° point anywhere along the scale. For example, you may want the 0° point to be a main entrance of a facility.

To program the north point:

1. Select Set north. The programming interface will be replaced by live video that asks you to aim the camera to the due north point.

2. At the live video screen, use the joystick to pan the camera to the desired position.

3. Press the iris + or the set (  ) key on the keypad to save the north point or press the iris - or esc key to cancel the north point. Both canceling and saving the north point returns you to the Coordinates page of the Preferences page.

Page 54

Legend IP User Manual

Coordinate font color. Coordinates will appear on screen in the color selected. Choices are as shown

onscreen. Default is White.

Coordinate font size. Coordinates will appear on screen in the font size selected. Choices are as shown

onscreen. Default is 14 pt.

Coordinate font weight. Coordinates will appear on screen in the font weight selected. Choices are as

shown onscreen. Default is Bold.

Block color. You can create a block (background) that offsets the coordinates from the video behind it.

The block will appear on screen in the color selected. Choices are as shown onscreen. Default is Black.

Block transparency. You can set the block (background) to be a solid color or a transparency. The block

will appear on screen in the transparency selected. Choices are as shown. Default is No color.

Page 55

Advanced programming

Chapter 5

Camera menu

The dome is ready to operate with its default settings. The defaults are optimized for general applications. You can customize the dome’s performance for advanced applications by changing the dome’s camera features in the Camera menu. One camera feature, however, is adjusted with the keys on your keypad. Backlight compensation is adjusted with the iris control key, while you are in auto exposure mode. Backlight compensation can also be adjusted through the programming of individual presets and tours.

Figure 36. Camera menu

Page 56

Legend IP

User Manual

Privacy Masks page

Privacy masks let you conceal sensitive areas (such as neighboring windows) to protect them from view on the monitor screen and in the recorded video. You can create 24 privacy masks (numbered 1 to 24) per dome. A maximum of eight privacy masks can be displayed at one time.

When creating your masks, it is a common practice to make them 50% larger than the areas you wish to cover so that the masked areas remain concealed at all times. Also, be aware that masks cannot be created in the area directly below the dome. See Figure 37.

Figure 37. Masks should be 50% larger than the areas to be covered and are not allowed directly below the dome

Mask

Area to be masked

Mask 50% larger than area to be covered

0°

(+90°)

Positive (+)

hemisphere

No masks allowed 20° either side of 90° (0°) tilt

To access the Privacy Masks page, select Camera and Privacy Masks.

Figure 38. Privacy masks page

180° (-90°)

Negative (-) hemisphere

90° (0°)

Note: Remember to select OK to save any changes you make on the page.

Mask number. The Mask number drop-down box allows you to select the mask number that you want to

program.

Page 57

Advanced programming

Chapter 5

Mask title. The Mask title box allows you to give each mask a unique title. Default numerical titles are

provided. There is a 60-character limit for all titles, but be aware of how much video you want to cover with your titles.

Title POS. The mask title will appear on screen in a default position on the monitor screen (upper center),

but you can reposition it with the Title POS button. Be aware of where you already have other titles (camera, presets, tours, macros, areas, and alarms) positioned.

To set the position of the mask title:

1. Select Title POS.

2. Use the joystick to move the title to the desired position.

3. Press the iris + or the set (  ) key on the keypad to save the new position or press the iris - or

esc key to cancel the new position.

Title font color. Individual mask titles will appear on screen in the color selected. Choices are as shown

onscreen. Default is White.

Title font size. Individual mask titles will appear on screen in the font size selected. Choices are as shown

onscreen. Default is 14 pt.

Title font weight. Individual mask titles will appear on screen in the font weight selected. Choices are as

shown onscreen. Default is Bold.

Mask color. You can customize the color of each mask. Individual masks will appear on screen in the

color selected. Choices are Gray (default) and Red.

Show. The Show button displays the mask that is currently selected. The screen will say “Privacy mask

preview” in the upper left corner. Press iris +, iris -, esc, or set (  ) to return to the menus.

Program. The Program button programs the mask. There are two screens for programming masks. The

first screen positions the camera view and the second screen sizes the mask.

To program masks:

1. Select Program on the programming interface.

The programming interface will be replaced by live video overlaid with a grid that asks you to establish the center of the privacy mask area.

2. Use the joystick to pan, tilt, and zoom the camera to the desired view.

3. Press the iris + or the set (  ) key on the keypad to save the center position of the mask or press the iris - or esc key to cancel the center position of the mask.

Canceling the camera view returns you to the Privacy Masks page. Saving the camera view advances you to the second mask-programming screen, which will set the mask size.

4. At the second screen (if you saved the camera view), use the joystick to adjust the height and width of the mask. Remember to make the mask 50% larger than the area you want to conceal.

Move the joystick up to increase the height, down to decrease the height, left to decrease the width, and right to increase the width.

5. Press the iris + or the set (  ) key to save the mask at the set size or press the iris - or esc key to cancel the mask.

Page 58

Legend IP

User Manual

Canceling the mask returns you to the first mask-programming screen, where you reposition the camera view. Saving the mask size saves the mask at the set size and returns you to the Privacy Masks page.

Clear. The Clear button deletes the mask that is currently selected.

Settings page

The features on Page1 and Page2 of the Settings page allow you to customize the dome’s performance for advanced applications.

Page1 tab

To access the Page1 page of Settings, select Camera, Settings, and Page1.

Figure 39. Page1 page

Note: Remember to select OK to save any changes you make on the page.

Day/Night. Day/Night is a camera feature that switches the camera mode from color (day) to

monochrome (night) and removes the IR cut filter, which increases the camera’s sensitivity in low light. It also allows the camera to function with IR lighting. Choices are Auto (default), Manual, and Off.

• Auto: Enables the camera to automatically switch between day (color) and night (monochrome) modes at a factory default light level. The factory default is not changeable. You can briefly override the day/night setting from a GE KTD-405 or 404 keypad. Within a few seconds, the dome will return to the mode (day or night) determined by the Auto setting.

Note: If the Day/Night feature’s Auto setting switches between color and monochrome eight times within a

minute, the Auto setting will be disabled for 30 minutes. After 30 minutes, the Auto setting will be enabled, if it is still programmed. Manual control of the Day/Night feature is available while the Auto setting is disabled.

Page 59

Advanced programming

Chapter 5

The Day/Night feature’s Auto setting works only if the Exposure Control feature is set to Auto or the Return to auto feature is set to On. While other features are controlling the exposure, the camera cannot use the Day/Night feature automatically. See Ta bl e 5 on page 51 for the interactions between the Day/Night feature’s Auto setting and the settings of the Control and Return to auto features.

Two conditions can prevent the camera from switching between the color and monochrome modes according the Day/Night feature’s Auto setting. One, if you’ve overridden the Control feature’s Auto setting with manual commands from the keypad. Two, if you’ve called a preset (or a command containing a preset) that is programmed to override the Control feature’s Auto setting.

In the second scenario, the camera returns to the Auto setting of the Control feature after you leave the preset. In the first scenario, you must issue a command to return to the Auto setting of the Control feature. Using the iris key on the keypad manually adjusts the camera’s iris setting or shutter speed, overriding the Auto setting of the Control feature. You must issue a pan or tilt command from the keypad to leave the manual override and return to the Auto setting of the Control feature. While you remain in the manual override, the camera will not switch between the day and night modes according to the changes in the lighting conditions.

• Manual: Allows you to manually switch the camera between day (color) and night (monochrome) modes using a command from the controlling device (keypad, ASCII control software, etc.). On a KTD-405, press and hold the Esc key, and press the Magnify button. On a KTD-404, a key must be programmed for this function. Contact Technical Support for instructions on how to reprogram a key. Manual switching between Day and Night is not available on the KTD-400.

• Off: Allows you to disable both the automatic and manual modes. The camera cannot be switched between the day and night modes. Switching commands from the keypad are ignored. The dome remains in the mode that it was in when Off was selected.

Table 5. Interactions between the Day/Night Auto setting and the Exposure Control feature

Return to auto

Primary settings

Both Day/Night and Control set to Auto.

Day/Night set to

Auto, but Control set to Shutter, Iris, or Manual.

setting Onscreen message Interaction

Not available None Works without issue.

Off Warning: Auto day/night

mode will not function with current settings!

On Warning: Auto day/night

mode will not function when exposure has not returned to auto mode.

If Return to auto is set to Off, then the exposure control never attains the auto state. The Day/Night Auto setting will not work.

If Return to auto is set to On, then the Day/Night Auto setting will work only if the exposure control returns to the auto state. You can return the exposure control to the auto state by sending a manual pan or tilt command from the keypad.

White balance. White balance is another camera feature that compensates for lighting conditions. It

adjusts the quality of all of the colors in the video by balancing the colors to achieve the truest white possible for the available lighting conditions (Tungsten, fluorescent, natural). To correctly set the white balance, focus the camera on a white object. Choices are Auto (default), Indoor, Outdoor, ATW, and Manual.

• Auto: This mode automatically adjusts the color within the 3000 to 7500 Kelvin color temperature range.

Page 60

Legend IP User Manual

• Indoor: This mode provides you with a fixed cooler color temperature setting.

• Outdoor: This mode provides you with a fixed warmer color temperature setting.

• ATW (autotracking white balance): This mode automatically adjusts the color, while the images

change, within the 2000 to 10000 Kelvin color temperature range.

• Manual: This mode allows you to manually adjust the current blue and red settings. After

selecting the Manual mode, select Set to access the red and blue scales.

• Red: This adjustment is available only if Manual white balance is selected. Settings range from 0

to 127. Default is 64.

• Move the joystick right to increase and left to decrease the red value.

•Press the iris + or the set (  ) key on the keypad to save the changed value or press the iris - or

esc key to cancel the changed value.

• Blue: This adjustment is available only if Manual white balance is selected. Settings range from 0

to 127. Default is 64.

• Move the joystick up to increase and down to decrease the blue value.

•Press the iris + or the set (  ) key on the keypad to save the changed value or press the iris - or

esc key to cancel the changed value.

Exposure settings. Exposure is a camera feature that establishes what controls the light coming into the

camera through the lens. Depending on your exposure selection under Control, one or more of the light controlling features (Autoslow shutter, Lowest shutter speed, and Return to auto) will be available.

Exposure/Control. Control is an exposure feature that determines which exposure control setting takes

priority in automatic and manual operation. Choices are Auto, Shutter, Iris (default), and Manual. See Tab le 6 on page 53 and Tab le 7 on page 53 for details about the exposure settings.

Exposure/Autoslow shutter. This feature is available only if the Exposure Control feature is set to Auto.

Autoslow shutter is a camera feature that compensates for lighting conditions. It automatically slows

the shutter speed as the light level entering the camera decreases so that more light can be gathered to increase image clarity. This feature works best when the camera is stationary. Because of the slowing shutter speed, any motion in the image will begin to blur. As the light level and the shutter speed continue to decrease, the blur of the video will gradually increase. Choices are Off (default) and On. See Tab le 6 on page 53 and Tab le 7 on page 53 for details about the exposure settings.

Exposure/Lowest shutter speed. This feature is available only if the Exposure Control feature is set to

Shutter or Manual. Lowest shutter speed is a camera feature that sets the lowest allowable shutter speed that can be used. Choices are as shown onscreen and are different for NTSC and PAL domes. See Tab le 6 on page 53 and Tab le 7 on page 53 for details about the exposure settings.

Exposure/Return to auto. This feature is available for all control settings, except Auto. Return to auto is

a camera feature that returns the dome to the Auto exposure mode when the camera is manually moved. Choices are Off and On (default). See Table 6 on page 53 and Tabl e 7 on page 53 for details about the exposure settings.

Page 61

Table 6. Exposure control settings

Exposure control setting

Advanced programming

Chapter 5

Operation

Function controlled by the iris keys

Backlight compensation (iris + for on and iris -

Auto Shutter Iris Manual

Shutter speed (sec) Iris setting (F-stop) First, iris setting (F-stop),

for off)

Automatic adjustments

•Iris setting (F-stop)

• Shutter speed (sec)

• Iris setting (F-stop)

•Gain (dB)

•Gain (dB) Except when the

shutter speed is below 1/60 sec. NTSC or 1/50 sec. PAL.

Available controls Autoslow shutter • Lowest shutter speed

• Return to auto

Table 7. Exposure options

Exposure option

Operation

Autoslow shutter Lowest shutter speed Return to auto

until limit reached. Second, shutter speed

(sec), until limit reached. Third, gain (dB).

• Shutter speed (sec)

N/A

•Gain (dB)

Return to auto • Lowest shutter speed

• Return to auto

Available for

Auto • Shutter which control setting

How it works Automatically slows the

shutter speed below the

normal setting as needed

to compensate for low-light

conditions.

•Manual

Sets the lowest allowable shutter speed.

•Shutter

•Iris

•Manual

Returns the dome to Auto exposure mode with any manual pan or tilt movement , thereby returning the iris toggle key to function as a control for the shutter speed, iris setting, or gain, depending on the exposure mode selected.

Page 62

Legend IP

User Manual

Page2 tab

To access the Page2 page of Settings, select Camera, Settings, and Page2.

Figure 40. Page2 page

Note: Remember to select OK to save any changes you make on the page.

Phase lock enabled. Phase lock enabled is a camera feature that allows synchronization of the video

signal to reduce picture roll on analog video switchers.

By default, the phase lock is off. As such, each camera synchronizes its video signal to its own internal clock crystal. This is called internal synchronization. If you enable phase lock (select On), you are selecting what is called line lock synchronization and the camera will synchronize its video signal to the AC input voltage. With line lock synchronization, you also adjust the vertical phase shift of a camera’s video signal to coordinate with other cameras. Due to differences in cameras, environments, and cable lengths, the phase shift will not be the same for all cameras being synchronized. Use an oscilloscope or a GE Security vertical phase adjustment tool (KTS-56). Contact your GE Security sales representative.

Phase adjustment. The Phase adjustment feature is available only if On is selected for

Phase lock enabled. Choices range from 0 to 127°. Default is 50°. These settings map to the angle

adjustment range of 0 to 360°. Use your oscilloscope or vertical phase adjustment tool to verify settings.

Stabilization. Stabilization is an optional camera feature that reduces video shaking for cameras that are

located in areas prone to vibration. It works best for low frequency vibration (3 to 10 Hz). If it is available for your camera, it creates a slight lag and movement backward when a pan/tilt movement stops. Choices are Off and On.

Digital zoom limit. Digital zoom limit is an electronic camera feature that increases the apparent size of

images beyond the magnification of the camera’s optical lens. Because image information is not also increased, there is some loss of image resolution. So test the different settings for suitability. Selecting a digital zoom setting that is too high can result in the loss of video clarity for some scenes. To test:

Page 63

Advanced programming

Chapter 5

Select a setting and use your keypad’s zoom key to zoom in and out. Choices range from 1x to 12x (default).

CAUTION: Lift and gain compensate for long runs of video coaxial cable. Only qualified personnel should adjust

these settings. Incorrect adjustments can impair video quality.

Lift. Lift is a camera feature that optimizes the video’s color over long runs of coaxial cable. Use the

joystick to adjust the lift. Right increases and left decreases the lift. Choices range from 0 to 7. Default is 0.

CAUTION: Lift and gain compensate for long runs of video coaxial cable. Only qualified personnel should adjust

these settings. Incorrect adjustments can impair video quality.

Gain. Gain is a feature that optimizes the video’s brightness over long runs of coaxial cable. Gain

increases the video signal’s amplitude to increase the brightness of darkened video and to reduce the noise of weakened video. Use the joystick to adjust the gain. Up increases and down decreases the gain. Choices range from 0 to 31. Default is 0.

Zoom speed. Zoom speed is a feature that sets the rate at which the zoom motors operate. There are three

fixed settings and one variable setting. If your keypad provides variable-speed control for zooming, you can use the Variable setting and the joystick’s range of motion for operation. Twist the joystick farther for faster zoom changes and less far for slower zoom changes. Choices are Variable (default), Slow, Medium, and Fast.

Note: If your keypad does not provide variable-speed control for zooming, then you must select one of the other

settings. The variable setting will not work.

Default preset freeze. Default preset freeze is a global setting that sets a default for image freeze to Off or

On. This setting works in conjunction with the Image freeze feature (see Edit page on page 61), which you can set to Default, Off, or On for individual presets. Be aware that the Transition feature (Freeze or Zoom out) must be programmed separately when presets are programmed into macros. See

Program page on page 68. Choices are Off (default) and On.

Tilt up limit. Tilt up limit is a feature that sets a programmable stop for the camera at the highest point

that you want it to tilt up. By default, the pan and tilt limits are off. Programming them turns them on.

If E-flip (see Speeds/Tracking page on page 89) is enabled (checkbox checked), constraints are placed upon the tilt limits. See Pan and tilt limitations on page 99 for limitations. To review tilt coordinates, see Coordinates page on page 44.

Tilt down limit. Tilt down limit is a feature that sets a programmable stop for the camera at the lowest

point that you want it to tilt down. By default, the pan and tilt limits are off. Programming them turns them on.

Pan left limit. Pan left limit is a feature that sets a programmable stop for the camera at the leftmost point

that you want it to pan left. By default, the pan and tilt limits are off. Programming them turns them on.

Page 64

Legend IP

User Manual

See Pan and tilt limitations on page 99 for limitations. To review pan coordinates, see Coordinates

page on page 44.

Pan right limit. Pan right limit is a feature that sets a programmable stop for the camera at the rightmost

point that you want it to pan right. By default, the pan and tilt limits are off. Programming them turns them on. See Pan and tilt limitations on page 99 for limitations. To review pan coordinates, see

Coordinates page on page 44.

Clear limits. Clear limits is a feature that clears all programmable stops that have been set for

the camera.

Encoder page

The encoder page contains the following settings.

Figure 41.

Video tab

On the video page, you can adjust different settings that affect the video encoded by the camera.

Quality. Choose a quality level that fits your needs and is supported by your network (Ta bl e 8).

Table 8. Quality settings and data rates

Quality setting Bandwidth requirements (kbps)

D1 full high 30fps 2000

D1 full medium 30 fps 1750

D1 full low 30 fps 1500

D1 high 15 fps 1500

D1 medium 15 fps 900

Page 65

Table 8. Quality settings and data rates

Quality setting Bandwidth requirements (kbps)

D1 medium-low 7fps 600

D1 low 5fps 300

D1 very-low 3fps 150

2CIF full 30fps 1500

2CIF high 15fps 600

2CIF medium 10fps 450

2CIF medium-low 7fps 300

2CIF low 5fps 150

CIF full 30 fps 600

CIF high 15fps 300

CIF medium 10fps 200

Advanced programming

Chapter 5

CIF medium-low 7fps 150

Video resolution, bit rate, and frame rate are determined by the quality setting you choose. The greyed out drop down boxes are there to tell you what the settings are for each quality setting, and they are not changeable by the user.

When viewing video over a network, a lower frame rate translates into what appears to be higher latency. For example, at 30fps, you see a new image every 30th of a second. At 5fps, you see a new frame every 5th of a second, or six times as long compared to 30fps. This delay in new images can mean difficulty controlling the unit because the screen updates at a slower rate.

Variable bit rate. You can choose a percentage that will allow the bit rate to vary by that amount based on

the complexity of the video being transmitted.

Preset. This allows you to choose the level of latency you prefer. If you choose low latency, the image

quality will be slightly reduced to decrease latency. If you choose normal, latency is balance with the quality of the image.

Page 66

Legend IP

User Manual

Control tab

On the control page, you can specify certain network settings. For the default settings, see Setting the encoder

ports on page 27.

Figure 42.

Enable Network port. To view video from the camera over a network, you must have this enabled. If you

don’t, there will be no IP video. The nonvideo IP interface will still function.

Listen port. This is the initial control connection port used by SymSecure server. The server will

automatically change this to an unspecified port. This field always reflects the initial value.

Control port. This is the initial control port used by SymNav clients. It is also used by SymSecure for

some features.

Streaming mode. Sender allows you to manually configure point-to-point streaming without a client to

broker the connection. For example, you could use this to connect a Legend IP to a SymNet directly.

Disabled turns this feature off.

Streaming address. This is the destination IP port for the streaming video in a point-to-point stream. The

default is 230.0.0.0. If the first portion of the IP address is 230, and the last three portions are zeros, the last three portions are automatically replaced by the last three portions of the Legend IP address. For example, if the IP address is 192.168.1.2, and the streaming address is 230.0.0.0, then the actual address is 230.168.1.2.

Streaming port. The port number that the streaming video will be sent to. This should match the

receiver’s streaming port. The default is 8092.

Sender control port. This is the extended control port used by SymNav for managing streaming. The

default is 8092.

Enable auto discovery. This enables SymSecure automatic discovery.

Page 67

Advanced programming

Chapter 5

Actions menu

You can program a variety of custom actions for each dome. Your custom actions include 127 preset positions, 16 ShadowTours, 32 macros, and 120 areas. You can edit the title and description of any action and you can reassign the positions of existing presets.

Remember that the keypad’s joystick will function as a simulated mouse or PTZ controller at different times during the programming of your actions.

Figure 43. Actions menu

Presets page

There are a total of 127 presets (1 through 127) that you can define for your dome. If you are using presets 62 and 63 for your left and right autopan limits, then you have a total of 125 presets that you can define.

The dome also provides the ability to remap any preset or tour command coming in from a keypad to activate any of the 127 presets, 16 tours, or 32 macro actions. This enables you to manually initiate any of the expanded capabilities of the dome from keypad controllers with limited command capability. See Command Map page on page 85.

Note: Most keypads have a limited number of preset numbers they can call. If you have a GE KTD-405 keypad with firmware

v1.2.09 or later, and it is operating with Impac RS-485 protocol, then you can call up all 127 preset numbers (1 through

Page 68

Legend IP

User Manual

Summary page

The summary page provides the number and title of all 127 presets (1 through 127) that are available for the dome, whether or not they are programmed or titled.

To access the Summary page of Presets, select Actions, Presets, and Summary.

Figure 44. Summary page

No. The No. column of the summary page lists all 127 presets (1 through 127) in numerical order, whether

or not they are programmed.

Title. The Title column of the summary page lists the titles of all 127 presets. The default titles are listed if

they have not been retitled.

Page 69

Advanced programming

Chapter 5

Edit page

The Edit page is where you program your presets. You can select any preset number, whether previously programmed with a preset position or not. You can reassign new positions to existing presets. After you have selected a number, you will select the Program button and program the preset position. After setting the position, you can use the Display and Advanced pages to program additional characteristics for the preset such as title and specific exposure modes, if needed.

To access the Edit page of Presets, select Actions, Presets, and Edit.

Figure 45. Edit page

Note: Remember to select OK to save any changes you make on the page.

No. The No. drop-down box allows you to select the preset number that you want to program or

reprogram.

Title. The Title box shows you the existing title for the selected preset number. You can customize the

default title on the Display page.

Image freeze. The Image freeze feature enables or disables image freeze, or uses a default freeze setting,

for displaying the video on the monitor screen as the camera travels between presets.

Selecting On (enabling Image freeze) sets the camera to freeze the last image while the camera is moving. A static image will show on the monitor screen until the camera stops. Selecting Off (disabling Image freeze) sets the camera to zoom out as it is moving and to zoom in when it arrives at its destination. Selecting Default uses the setting selected for the Default preset freeze feature under Camera | Settings | Page2 (see Page2 tab on page 54).

Be aware that the Transition feature (Freeze or Zoom out) must be programmed separately when presets are programmed into macros. See Program page on page 68. Choices are Default, Off (default), and On.

Show. The Show button displays the preset that is currently selected. The screen will say “Show preset” in

the upper left corner. Press iris +/-, esc, or set (  ) to return to the menus.

Page 70

Legend IP

User Manual

Program. The Program button programs the preset. There is one screen for programming presets.

To program a preset:

1. Select Program. The programming interface will be replaced by live video that asks you to set the desired position for the preset.

2. At the live video screen, use the joystick to pan, tilt, and zoom the camera to the desired position.

3. Press the iris + or the set (  ) key on the keypad to save the preset position or press the iris - or esc key to cancel the preset position. Both canceling and saving the preset position returns you to the Edit page of the Presets page.

Clear. The Clear button deletes the preset that is currently selected.

Display page

To access the Display page of Presets, select Actions, Presets, and Display.

Figure 46. Display page

Note: Remember to select OK to save any changes you make on the page.

No. The No. drop-down box allows you to select the preset number that you want to program.

Title. The Title box allows you to give each preset a unique title. Default numerical titles are provided.

There is a 60-character limit for all titles, but be aware of how much video you want to cover with your titles.

Title POS. The preset title will appear on screen in a default position on the monitor screen (bottom

center), but you can reposition it with the Title POS button. Be aware of where you already have other titles (camera, privacy masks, tours, macros, areas, and alarms) positioned.

To set the position of the preset title:

1. Select Title POS.

Page 71

Advanced programming

Chapter 5

2. Use the joystick to move the title to the desired position.

3. Press the iris + or the set (  ) key on the keypad to save the new position or press the iris - or

esc key to cancel the new position.

Display title on screen. The Display title on screen feature sets the preset title to appear on the monitor

screen, if checked. Choices are checked (default) and unchecked.

Title duration. The Title duration feature defines how long the preset title appears on the monitor screen.

Choices are Infinite (default) and 5 to 120 seconds in 5-second increments.

Title font color. The preset title will appear on screen in the color selected. Choices are as shown

onscreen. Default is White.

Title font size. The preset title will appear on screen in the font size selected. Choices are as shown

onscreen. Default is 14 pt.

Title font weight. The preset title will appear on screen in the font weight selected. Choices are as shown

onscreen. Default is Bold.

Block color. You can create a block (background) that offsets the preset title from the video behind it. The

block will appear on screen in the color selected. Choices are as shown onscreen. Default is Black.

Block transparency. You can set the block (background) to be a solid color or a transparency. The block

will appear on screen in the transparency selected. Choices are as shown onscreen. Default is No color.

Page 72

Legend IP

User Manual

Advanced page

The Advanced page of the Presets page (under the Actions menu) allows you to change a camera’s feature settings for individual presets.

To access the Advanced page of Presets, select Actions, Presets, and Advanced.

Figure 47. Advanced page

Note: Remember to select OK to save any changes you make on the page.

No. The No. drop-down box allows you to select the preset number that you want to program.

Title. The Title box shows you the existing title for the selected preset number. You can customize the

default title on the Display page.

Use custom camera state for preset. The Use custom camera state for preset feature overrides the

settings that were set for the camera’s normal operation under Camera | Settings, if checked. You must check this feature to make the other features on this page available.

Night mode. For individual presets, you can use the Night mode feature to change the camera’s Day/Night

setting. See Page1 tab on page 50 for details about the Day/Night feature and its interactions with the Exposure feature settings. Choices are Off (default) and On.

When you turn on the Night mode feature, you are telling the camera to override the normal Day/Night operating setting as follows:

• Auto: If the Day/Night feature is set to Auto under Camera | Settings, then the Night mode feature will use the Day/Night setting customized for the preset for 5 to 10 seconds. After 5 to 10 seconds, the camera will revert to the normal operating setting and adjust for the current light conditions.

• Manual: If the Day/Night feature is set to Manual under Camera | Settings, then the Night mode feature will use the Day/Night setting customized for the preset until the preset is left. After the preset is left, the camera will revert to the Day/Night setting that it was using before the preset was called.

• Disabled: If the Day/Night feature is set to Manual under Camera | Settings, then the Night mode feature will do nothing.

Page 73

Advanced programming

Chapter 5

Backlight. For individual presets, you can change the camera’s Backlight compensation setting. Backlight

compensation is a feature that illuminates the display so that the foreground appears sharper in contrast

with the background. Choices are Off (default) and On.

White balance. For individual presets, you can use this White balance feature to change the camera’s

White balance setting. White balance is the feature that compensates for lighting conditions. See

Page1 tab on page 50. Choices are Auto (default), Indoor, Outdoor, ATW, and Manual.

• Auto: This mode automatically adjusts the color within the 3000 to 7500 Kelvin color temperature range.

• Indoor: This mode provides you with a fixed cooler color temperature setting.

• Outdoor: This mode provides you with a fixed warmer color temperature setting.

• ATW (autotracking white balance): This mode automatically adjusts the color, while the images changes, within the 2000 to 10000 Kelvin color temperature range.

• Manual: This mode allows you to manually adjust the current blue and red settings. After selecting the Manual setting, select Set to access the red and blue scales.

• Red: This adjustment is available only if Manual white balance is selected. Settings range

from 0 to 127. Default is 64.

• Move the joystick right to increase and left to decrease the red value.

• Press the iris + or the set (  ) key on the keypad to save the changed value or press the iris - or esc key to cancel the changed value.

• Blue: This adjustment is available only if Manual white balance is selected. Settings range from 0 to 127. Default is 64.

• Move the joystick up to increase and down to decrease the blue value.

• Press the iris + or the set (  ) key on the keypad to save the changed value or press the

iris - or esc key to cancel the changed value.

Exposure. For individual presets, you can use this Exposure Control feature to change the camera’s

Exposure setting. See Page1 tab on page 50 for details about the Exposure features. Choices are Auto

(default), Shutter, Iris, and Manual.

•

Auto: Selecting this setting makes the camera determine what features (iris aperture, gain, shutter speed, or combination thereof) control the incoming light. You will not be able to set values for iris, gain, or shutter speed.

• Shutter: The shutter speed controls the length of time that the aperture is open to let light into the camera through the lens. You will not be able to set values for iris or gain. The choices for shutter speed are as shown onscreen.

• Use the zoom +/- key on the keypad to scroll through the choices, then press the iris + or the set (  ) key on the keypad to save the changed value or press the iris - or esc key to cancel the changed value.

• Iris: The iris F-stop controls the size of the aperture that lets light into the camera through the lens. You will not be able to set values for gain or shutter speed. The choices for iris F-stop are as shown onscreen.

Use the zoom +/- key on the keypad to scroll through the choices, then press the iris + or the set (  ) key on the keypad to save the changed value or press the iris - or esc key to cancel the changed value.

Page 74

Legend IP

User Manual

• Manual: You control the light coming into the camera through the lens by setting specific values

for iris, gain, and shutter speed. The choices are as shown onscreen. After selecting the Manual setting, select Set to access each shutter, iris, and gain controls. The choices for each are as shown onscreen.

ShadowTours page

You have a total of 16 ShadowTours (totaling 20 minutes) that you can define for the dome.

To access the ShadowTours page, select Actions and ShadowTours.

Figure 48. ShadowTours page

Note: Remember to select OK to save any changes you make on the page.

No. The No. drop-down box allows you to select the ShadowTour number that you want to program.

Title. The Title box allows you to give each ShadowTour a unique title. Default numerical titles are

provided. There is a 60-character limit for all titles, but be aware of how much video you want to cover with your titles.

Title POS. The ShadowTour title will appear on screen in a default position on the monitor screen (center,

above the macro title default position), but you can reposition it with the Title POS button. Be aware of where you already have other titles (camera, privacy masks, presets, macros, areas, and alarms) positioned.

To set the position of the preset title:

1. Select Title POS.

2. Use the joystick to move the title to the desired position.

Page 75

Advanced programming

Chapter 5

3. Press the iris + or the set (  ) key on the keypad to save the new position or press the iris - or

esc key to cancel the new position.

Title font color. The ShadowTour title will appear on screen in the color selected. Choices are as shown

onscreen. Default is White.

Title font size. The ShadowTour title will appear on screen in the font size selected. Choices are as shown

onscreen. Default is 14 pt.

Title font weight. The ShadowTour title will appear on screen in the font weight selected. Choices are as

shown onscreen. Default is Bold.

Block color. You can create a block (background) that offsets the ShadowTour title from the video behind

it. The block will appear on screen in the color selected. Choices are as shown onscreen. Default is Black.

Block transparency. You can set the block (background) to be a solid color or a transparency. The block

will appear on screen in the transparency selected. Choices are as shown onscreen. Default is No color.

Show. The Show button displays the ShadowTour that is currently selected. Press iris +, esc, or set (  ) to

return to the menus.

Note: If your ShadowTour is longer than the inactivity timer of the keypad or the programming interface, you may

not see the entire tour, unless you exit the programming interface and view the ShadowTour from the video screen. See Inactivity timer on page 23.

Program. The Program button programs the ShadowTour.

To program a ShadowTour:

1. Select Program. The programming interface will be replaced by live video.

2. At the live video screen, use the joystick to pan, tilt, and zoom the camera to the desired

starting point of the ShadowTour.

3. Press the iris + or the set (  ) key on the keypad to start the timer for the ShadowTour.

4. Use the joystick to pan, tilt, and zoom the camera through the desired views.

5. Press the press the iris + or the set (  ) key on the keypad to stop the timer and save the

ShadowTour, or press the iris - or esc key to cancel the ShadowTour.

Clear. The Clear button deletes the ShadowTour that is currently selected.

Page 76

Legend IP

User Manual

Macros page

You can program 32 macros per dome, which include six preprogrammed system macros to send e-mail. Each macro can contain up to 16 steps. Each step can contain a preset, ShadowTour, relay action, jump command, or macro command. These are the step types. The step type determines what additional features are available for programming. Each macro can contain any number of the macro step types described.

Program page

Select a macro (1 through 32), and if no steps already exist, select Append to add the first step and make the other programming features available.

To access the Program page of Macros, select Actions, Macros, and Program.

Figure 49. Program page

Note: Remember to select OK to save any changes you make on the page.

No. The No. drop-down box allows you to select the macro number that you want to program. The Legend

IP comes with 6 preprogrammed macros (Ta bl e 9, Preprogrammed macros).

Table 9. Preprogrammed macros

Macro no. Action

Video loss An email is sent when a camera module failure is detected.

Settings change An email is sent when any camera setting is modified, except video encoder settings.

Video change An email is sent when the video encoder settings are modified.

Menus accessed An email is sent when the GUI is activated.

Ethernet connection An email is sent when one of the control ports is activated.

Motor error An email is sent when the motors stall due to an obstruction.

Page 77

Advanced programming

Chapter 5

Title. The Title box shows you the existing title for the selected macro number. You can customize the

default title on the Display page.

Macro list. The macro list (step, type, no., speed, zoom, and duration) shows the defined steps for the

macro in sequential order. You can use the buttons and drop-down boxes located below the summary to add, delete, move up, or move down individual steps. The Append button adds steps.

Step. The Step box selects the step number you want to program. If no steps already exist, you must select

Append to add the first step and make the other programming features available.

Type. The Type box selects the action for the selected step. It determines what additional features appear

(are available) for programming. Choices are Preset (default), Tour, Macro, Relay, and Jump (jumps to a prior step), or Email.

Type #. The Type # feature selects which of the group defined by the Type selection (for example, presets)

is to be assigned to the step. The type number changes its name depending on the type selected under Type (Preset, Tour, Macro, Relay, Jump, or Email).

# Repeats. The # Repeats feature appears if the Jump type is selected and allows you to repeat a jump step

up to 49 times.

Email. The address to send an email to.

Message. The message to send when emailing.

Speed. The Speed feature appears if the Preset or Tour type is selected and allows you to set how fast the

camera will move to the preset step or to the start position of a tour. Choices are Slow, Medium, Fast, and Max.

Transition. The Transition feature appears if the Preset or Tour type is selected and allows you to set how

the video will be seen on the monitor screen between presets or tours. Choices are Freeze (default) and Zoom out.

• Freeze: Selecting this setting freezes the last image on the monitor screen while the camera is moving. A static image will show on the monitor screen until the camera stops.

• Zoom out: Selecting this setting zooms the camera out before it moves, remains zoomed out during travel, and reestablishes the set zoom when it arrives at its destination.

Duration. The Duration feature defines how long the action for the step continues.

•For presets, the duration is the dwell time that the camera remains at a preset before continuing on to the next macro step. Choices are 1 to 60 seconds in 1-second increments.

•For relays, the duration is a timer for the relay action. The next macro step is immediately performed after the relay timer runs out. Choices are Infinite (default) and seconds (5 to 120 in 5-second increments). The relay will maintain its state (on/off) for the duration specified.

Energize.

The Energize feature appears if the Relay type is selected and, if checked, sets the relay to its energized state. Which is closed for a normally open connection and open for a normally closed connection.

Display title. The Display title feature sets the macro title to appear on the monitor screen, if checked.

Append. The Append button adds one step to the bottom of the list of macro steps.

Remove. The Remove button deletes the currently selected step.

Page 78

Legend IP

User Manual

Move up. The Move up button moves the currently selected step up one step number in the macro

sequence each time it is selected.

Move down. The Move down button moves the currently selected step down one step number in the

macro sequence each time it is selected.

Display page

To access the Display page of Macros, select Actions, Macros, and Display.

Figure 50. Display page

Note: Remember to select OK to save any changes you make on the page.

No. The No. drop-down box allows you to select the macro number that you want to program.

Title. The Title box allows you to give each macro a unique title. Default numerical titles are provided.

There is a 60-character limit for all titles, but be aware of how much video you want to cover with your titles.

Title POS. The macro title will appear on screen in a default position on the monitor screen (center, below

the tour title default position), but you can reposition it with the Title POS button. Be aware of where you already have other titles (camera, privacy masks, presets, tours, areas, and alarms) positioned.

To set the position of the macro title:

1. Select Title POS.

2. Use the joystick to move the title to the desired position.

3. Press the iris + or the set (  ) key on the keypad to save the new position or press the iris - or

esc key to cancel the new position.

Title font color. The macro title will appear on screen in the color selected. Choices are as shown

onscreen. Default is White.

Page 79

Advanced programming

Chapter 5

Title font size. The macro title will appear on screen in the font size selected. Choices are as shown

onscreen. Default is 14 pt.

Title font weight. The macro title will appear on screen in the font weight selected. Choices are as shown

onscreen. Default is Bold.

Block color. You can create a block (background) that offsets the ShadowTour title from the video behind

it. The block will appear on screen in the color selected. Choices are as shown onscreen. Default is Black.

Block transparency. You can set the block (background) to be a solid color or a transparency. The block

will appear on screen in the transparency selected. Choices are as shown onscreen. Default is No color.

Areas page

Areas are used primarily to provide onscreen titles of camera views. They can also serve to conceal sensitive areas like privacy masks do. When using areas to conceal sensitive areas, they replace the entire video image with a blue screen, whereas privacy masks cover only a portion of the video displayed. As with privacy masks, areas are triggered by the camera passing through a defined center point. You can create 120 areas.

When creating your areas, be aware that they are triggered by their center viewpoint. Therefore, it is a common practice to make areas twice the size of the area that you wish to conceal so that the areas are properly triggered when the camera enters the trigger zone.

Summary page

The summary page provides the number and title of all areas that are programmed for the dome.

To access the Summary page of Areas, select Actions, Areas, and Summary.

Figure 51. Summary page

No. The No. column of the summary page lists all 120 areas in numerical order, whether programmed or

not.

Page 80

Legend IP

User Manual

Title. The Title column of the summary page lists the titles of all 120 areas. The default titles are listed if

they have not been retitled.

Display page

To access the Display page of Areas, select Actions, Areas, and Display.

Figure 52. Display page

Note: Remember to select OK to save any changes you make on the page.

No. The No. drop-down box allows you to select the area number that you want to program.

Title. The Title box allows you to give each area a unique title. Default numerical titles are provided.

There is a 60-character limit for all titles, but be aware of how much video you want to cover with your titles.

Blank screen while in view. The Blank screen while in view feature replaces the video of a selected area

with a blue screen. Choices are On (default) and Off. When on, the video is replaced with a blue screen and title when the camera enters the masked area. When off, the video is not blanked, but an area title appears in an area that is programmed.

Title POS. The area title will appear on the monitor screen in a default position (upper center), but you

can reposition it with the Title POS button. Be aware of where you already have other titles (camera, privacy masks, presets, tours, macros, and alarms) positioned.

To set the position of the macro title:

1. Select Title POS.

2. Use the joystick to move the title to the desired position.

3. Press the iris + or the set (  ) key on the keypad to save the new position or press the iris - or

esc key to cancel the new position.

Page 81

Advanced programming

Chapter 5

Title font color. Individual area titles will appear on screen in the color selected. Choices are as shown

onscreen. Default is White.

Title font size. Individual area titles will appear on screen in the font size selected. Choices are as shown

onscreen. Default is 14 pt.

Title font weight. Individual area titles will appear on screen in the font weight selected.Choices are as

shown onscreen. Default is Bold.

Block color. You can create a block (background) that offsets the title from the video behind it. Individual

area blocks will appear on screen in the color selected.Choices are as shown onscreen. Default is Black.

Block transparency. You can set the block (background) to be a solid color or a transparency. Individual

area blocks will appear on screen in the transparency selected. Choices are as shown onscreen. Default is No color.

Show. The Show button displays the area that is currently selected. Press iris +, esc, or set (  ) to return to

the menus.

Program. The Program button programs the area. There are two screens for programming areas.

To program an area:

1. Select Program. The programming interface will be replaced by live video overlaid with a grid that asks you to establish the upper left corner of the area.

2. At the first screen (live video), use the joystick to pan, tilt, and zoom the center of the grid to the upper left corner of the desired view.

3. Press the iris + or the set (  ) key on the keypad to save the upper left corner position or press the iris - or esc key on the keypad to cancel it. Canceling the position returns you to the Display page of the Areas page. Accepting the position advances you to the second areaprogramming screen.

4. At the second screen, use the joystick to pan, tilt, and zoom the center of the grid to the lower right corner of the desired view.

5. Press the iris + or the set (  ) key on the keypad to save the lower right corner position or press the iris - or esc key on the keypad to cancel it. Canceling the position returns you to the first area-programming screen, where you reposition the camera view. Accepting the position returns you to the Display page.

Clear. The Clear button deletes the area that is currently selected.

Page 82

Legend IP

User Manual

Time schedule page

You can program 64 schedules per dome. Time scheduling automatically drives your cameras for expected events, like scheduled deliveries, shift changes, and the opening and closing of malls and schools. You schedule individual domes to automatically initiate presets, ShadowTours, or macros toward specific entry and exit points on any recurring day so that your operators can keep their attention on surveying and other activities.

Legend IP domes need to synchronize periodically for the time schedules to operate correctly. Therefore, you must install time synchronization equipment if you want to use time schedules. If you need recommendations for time synchronization equipment, contact your GE sales representative or Technical Support.

Note: If the Legend cannot synch, the time schedule will not function.

Summary page

To access the Summary page of Time schedule, select Actions, Time schedule, and Summary.

Figure 53. Summary page

Schedule days. The Schedule days drop-down box allows you to select which schedule summary you

wish to view. Choices are Today (default), Daily, Weekdays, Weekends, Holidays, Sunday, Monday, Tuesday, Wednesday, Thursday, Friday, and Saturday.

Page 83

Advanced programming

Chapter 5

Main page

The Main page schedules automatic dome actions that coordinate with regular day-to-day activities, while the Holidays page schedules exceptions to those regularly scheduled dome actions.

Select a schedule (1 through 64), and if no event already exists, select Insert to add an event and reveal the programming features.

To access the Main page of Time schedule, select Actions, Time schedule, and Main.

Figure 54. Main page

Note: Remember to select OK to save any changes you make on the page.

Schedule list. The schedule list shows the schedules that are programmed in sequential order

(1 through 64) with recurrence, action, and time.

Schedule. The Schedule feature selects the schedule number you want to program. Choices are 1 through

64.

Days. The Days feature selects the recurrence of the scheduled action. Choices are Daily (default),

Weekdays, Weekends, Holidays, Sunday, Monday, Tuesday, Wednesday, Thursday, Friday, and Saturday.

Type. The Type feature selects the action to recur. Choices are Preset (default), Macro, ShadowTour, and

Autopan.

Number. The Number feature selects which member of the action group (preset, macro, or ShadowTour)

is to recur, if Autopan is not selected as the Type. The choices are based on the selected Ty pe.

Hour. The Hour feature selects the hour in a 24-hour day (0 through 23) that the schedule is to be

initiated. Also see the Minute feature.

Minute. The Minute feature selects the minute (00 through 59) during the hour that the schedule is to be

initiated.

Page 84

Legend IP

User Manual

Insert. The Insert button adds one schedule to the bottom of the list of schedules. Until you change the

selected schedule number, changes to page features will be applied to the last step inserted.

Clear. The Clear button deletes the schedule that is currently selected with the Schedule feature.

Holidays page

The Holidays page schedules exceptions to the regularly scheduled dome actions, while the Main page schedules the automatic dome actions that coordinate with regular day-to-day activities. On the days that holiday exceptions are programmed, the actions that are regularly scheduled will be superseded by the holiday action.

To access the Holidays page of Time schedule, select Actions, Time schedule, and Holidays.

Figure 55. Main page

Note: Remember to select OK to save any changes you make on the page.

Holiday list. The holiday list shows the dates that are programmed as exceptions to the programmed

schedules.

Holiday. The Holiday feature allows you to specify calendar dates for individual holidays. Select the

month, day, and year, then select the Insert button.

Insert. The Insert button adds the holiday that is currently selected by the month, day,

and year drop-down boxes to the list of holidays. Holidays are added to the bottom of the list.

Erase. The Erase button deletes the holiday that is currently selected by the month, day, and year drop-

down boxes.

Clear all. The Clear all button deletes all of the holidays.

Page 85

Advanced programming

Chapter 5

Alarms menu

You can program up to eight alarm inputs and two relay outputs per dome. Each alarm input can call up any preset, macro (preset tour or programmed routine), or ShadowTour. The eight alarms are numbered from 1 to 8.

Programming tips for dome alarms

Legend IP domes do not handle alarms the same way as most other alarm equipment. You need to be aware of the differences to manage the dome’s inputs and outputs effectively. Here are some key concepts.

• You can set each alarm to have up to three components: a dome action (preset, tour, or macro), a relay 1 action (on or off), and a relay 2 action (on or off). The relays can be used to trip such devices as lights, doors, or alarm inputs on other devices. A dome action is not required. You could have an alarm action one or both relays. An alarm with no action or relay settings does not affect dome operation.

• The priority that you set for the alarms determines which one is actioned.

• When an alarm action is set to a preset, tour, or macro, the camera will remain with that action until the operator issues another camera command from the keypad. The Resume feature is disabled by alarms.

• Alarms are not held in a queue. Only the highest priority alarm that is activated is actioned. If several alarms are activated at the same time, then the one with the highest priority is actioned. After that alarm has finished, the next highest priority alarm will be actioned only if it is still active. If a higher priority alarm is activated while a lower priority alarm is being actioned, then the higher priority alarm overrides the lower priority alarm and is actioned instead. After the higher priority alarm has finished being actioned, then the lower priority alarm will have its action restarted. But only if it is still active.

• You do not need to acknowledge dome alarms in the same sense as required by typical alarm equipment. To move the camera from the position of the alarmed action and reenable the Resume feature, however, you do need to issue a command from the keypad. An alarm that has been triggered and cleared will not be recognized again by the dome until another alarm is triggered, or a command from a keypad is received.

• Faulty dome alarms cannot be shunted. If you cannot readily repair the alarm wiring and/or contact of a faulty dome alarm, you can lower its priority and program the alarm box to display only the highest priority alarms, or you can reprogram the faulty alarm with no action or relays.

• The only time you need to “clear” a relay state is when you have set a relay with the Infinite duration.

• If you have a relay set to the Infinite duration, you can clear it one of three ways. One, you can manually clear it by selecting a Relay Off button on the Relay State page. Two, you can automatically clear it by using another programmed alarm number that sets that relay with a duration of at least five seconds. And three, you can clear it with a remapped preset command that activates a macro from the keypad. To remap preset commands, see Command Map page on page 85. An example of the second scenario would be Alarm 1 being used with a badge reader to open a door and Alarm 2 being used with a PIR on the other side of the door to lock the door. Alarm 1 would energize a relay with an infinite duration to open the electronic door lock and Alarm 2 would deenergize the relay with at least a fivesecond duration to close the electronic door lock.

• If you select the Relay 1 on or the Relay 2 on button on the Relay Status page, and select OK, then you are programming the dome to activate either or both of these relays each time the dome is powered up. The relay action becomes a default.

• Even though you can create an alarm block title and alarm titles that are up to 60 characters, we suggest limiting titles to 15 characters to reduce the size of the video obstruction.

Page 86

Legend IP

User Manual

Figure 56. Alarms menu

Summary page

You can view the status of alarms from the summary page. Alarms are presented in numerical order with whatever titles have been assigned. Statuses are as follows:

• On: Status shows as On if the contact for the alarm is in its active state. So, for a NO (normally open)

contact that is closed, the status reports as on, because it is in its activated, abnormal state.

• Off: Status shows as Off if the contact for the alarm is in its inactive state. So, for a NC (normally

closed) contact that is closed, the status reports as off, because it is in its normal state.

Upon initial installation, all alarm contacts are NO. All changes will refresh immediately.

Page 87

Advanced programming

To access the Summary page of Alarms, select Alarms and Summary. These will update dynamically.

Figure 57. Summary page

Chapter 5

No. The No. column of the summary page lists all alarms in numerical order, whether programmed or not.

The eight alarms are numbered from 1 to 8.

Title. The Title column of the summary page lists the titles for all available alarms, whether programmed

or not.

Status. The Status column of the summary page lists the status of each programmed alarm as either on

(active) or off (inactive).

Page 88

Legend IP

User Manual

Contact Setup page

The Contact Setup page is where you define the individual alarms. For tips, see Programming tips for dome

alarms on page 77.

To access the Contact Setup page of Alarms, select Alarms and Contact Setup.

Figure 58. Contact Setup page

Note: Remember to select OK to save any changes you make on the page.

Contact no. The Contact no. drop-down box allows you to select the alarm number that you want to

program.

Contact type. Alarm contacts are identified as NO (normally open) or NC (normally closed). Default is

NO.

Contact name. The Contact name box allows you to give your alarms unique titles. Default numerical

titles are provided. There is a 60-character limit for all titles, but be aware of how much video you want to cover with your titles.

Action. The Action feature can associate a programmed action with an alarm. An action is

not required. Choices are None (default), Preset, Tour, and Macro. If you select Preset, Tour, or Macro, the Action number feature is activated to let you select a specific one.

Action number. The Action number feature lets you select a specific preset, tour, or macro, if you selected

Preset, Tour, or Macro in the Action feature.

Relay 1. Each Relay feature can associate one relay action with an alarm. Relays can be used to trip such

devices as speakers, doors, and DVMRs. You can set both relays to activate with an alarm. Choices are No action (default), On, and Off.

Duration. The Duration feature defines how long the relay is active. Choices are Infinite (default) and

seconds (5 through 120 seconds in 5-second increments). The Infinite duration does not end unless another alarm is tripped.

Page 89

Advanced programming

Chapter 5

Relay 2. Each Relay feature can associate one relay action with an alarm. Relays can be used to trip such

devices as speakers, doors, and DVMRs. You can set both relays to activate with an alarm. Choices are No action (default), On, and Off.

Duration. The Duration feature defines how long the relay is active. Choices are Infinite (default) and

seconds (5 through 120 seconds in 5-second increments). The Infinite duration does not end unless another alarm is tripped.

Priority page

You can assign a priority ranking to your alarms that is independent of their contact numbers. The topmost alarm in the priority list is the highest priority regardless of the alarm’s number, while the bottommost alarm is the lowest priority. If more than one alarm is activated sequentially, only the highest priority alarm is actioned. If several alarms are activated at the same time, then the one with the highest priority is actioned. After that alarm has cleared, the next highest priority alarm will be actioned only if it is still active (for instance, a door is still open). Alarms are not held in a queue.

To access the Priority page of Alarms, select Alarms and Priority.

Figure 59. Priority page

Note: Remember to select OK to save any changes you make on the page.

Reset. The Reset button reorders the alarms in numerical order.

Raise priority. The Raise priority button moves a selected alarm up in the priority list. Select an alarm by

its title, then select Raise priority to move it up in the list.

Lower priority. The Lower priority button moves a selected alarm down in the priority list. Select an

alarm by its title, then select Lower priority to move it down in the list.

Page 90

Legend IP

User Manual

Display page

The Display page is where you define the appearance of the block of alarms and relays that displays on the monitor screen. To display the alarm block at all times, you must set the Alarm box content to All status and the Alarm box duration to Infinite.

To access the Display page of Alarms, select Alarms and Display.

Figure 60. Display page

Note: Remember to select OK to save any changes you make on the page.

Alarm title. This Alarm title feature does not title the individual alarms. Alarms appear in a list (or block)

on the monitor screen according to the display settings you set. You can give this alarm block a title with this feature to identify the group of alarms displayed. There is a 60-character limit, but be aware of how much video you want to cover with your alarm block.

Title POS. The alarm block will appear on screen in a default position on the monitor screen (upper

right), but you can reposition it with the Title POS button. Be aware of where you already have other titles (camera, privacy masks, presets, tours, macros, and areas) positioned.

To set the position of the alarm box title:

1. Select Title POS.

2. Use the joystick to move the title to the desired position.

3. Press the iris + or the set (  ) key on the keypad to save the new position or press the iris - or

esc key to cancel the new position.

Title font color. Alarm titles will appear on screen in the color selected. Choices are as shown onscreen.

Default is Red.

Title font size. Alarm titles will appear on screen in the font size selected. Choices are as shown onscreen.

Default is 12 pt.

Page 91

Advanced programming

Chapter 5

Title font weight. Alarm titles will appear on screen in the font weight selected. Choices are as shown

onscreen. Default is Bold.

Note: If All status is selected for the Alarm box content feature, then the selected Title font weight is overridden and

all alarms are listed in the alarm box with normal weight and only the active alarms are listed with bold weight.

Block color. You can create a block (background) that offsets the alarm block from the video behind it.

The blocks will appear on screen in the color selected. Choices are as shown onscreen. Default is White.

Block transparency. You can set the block (background) to be a solid color or a transparency. The blocks

will appear on screen in the transparency selected. Choices are as shown onscreen. Default is Solid.

Alarm box content. The Alarm box content feature sets how many alarms will display on the monitor

screen in the alarm block. Choices are Off (displays no alarms, whether active or inactive), All status (displays all alarms, whether active or inactive), Highest priority (displays only the highest priority alarm, when active), and Active only (displays all active alarms). Active alarms appear as bold in the list when All status is selected. Default is All status.

Alarm box duration. The Alarm box duration feature sets how long the alarm block will display on the

monitor screen, when All status is selected for the Alarm box content feature. Choices are During action (default) and Indefinite (always displayed).

Page 92

Legend IP

User Manual

Relay Status page

To access the Relay Status page of Alarms, select Alarms and Relay Status.

Figure 61. Relay State page ( Alarms | Relay State )

Note: Remember to select OK to save any changes you make on the page.

Name. The Name column of the summary page lists both relays in numerical order, whether programmed

or not. The two relays are numbered 1 and 2.

State. The State column of the summary page lists the status of each programmed relay as either on

(active) or off (inactive).

Relay 1 on. The Relay 1 on button lets you turn relay 1 on regardless of the current state of any associated

alarm.

Note: If you select Relay 1 on and select OK, then you are programming the dome to activate this relay each time

the dome is powered up.

Relay 1 off. The Relay 1 off button lets you turn relay 1 off regardless of the current state of any

associated alarm.

Relay 2 on. The Relay 2 on button lets you turn relay 2 on regardless of the current state of any associated

alarm.

Note: If you select Relay 2 on and select OK, then you are programming the dome to activate this relay each time

the dome is powered up.

Relay 2 off. The Relay 2 off button lets you turn relay 2 off regardless of the current state of any

associated alarm.

Show relay state. The Show relay state feature, when checked, lets you display the status of the relays on

the monitor screen at all times. If the status of alarms is also being displayed, the relays will be listed at the bottom of the list after the alarms.

Page 93

Advanced programming

Chapter 5

Control menu

You can program a variety of general camera features that control each dome. These general features include a specific operation for the camera to execute when it is first powered up (Power-on), a specific operation for the dome to execute when the dome has been inactive for a specified period of time (Resume), and speed settings for panning, tilting, autopanning, and moving between presets.

Figure 62. Control menu

Command Map page

The dome provides the ability to remap any preset or tour command coming in from a keypad to activate any of the 127 presets, 16 tours, or 32 user macro actions. This enables you to manually initiate any of the expanded capabilities of the dome from keypad controllers with limited command capability. The command mapping does not affect any of the internal command operations the dome performs, such as resume and alarm actions. It only affects the actions the dome will perform when it receives a command from an external device (keypad or alarm interface). An example of remapping is using a preset command from the keypad to run Macro 1. In the command map programming, you would select the preset number you wish to use and remap that command to activate Macro 1.

Note: Most keypads have a limited number of preset numbers they can call. If you have a GE KTD-405 keypad with firmware

v1.2.09 or later, and it is operating with Impac RS-485 protocol, then you can call up all 127 preset numbers (1 through

To create your presets, see Presets page on page 59.

To create your tours, see ShadowTours page on page 66.

To create your macros, see Macros page on page 68.

Page 94

Legend IP

User Manual

To access the Command Map page, select Control and Command Map.

Figure 63. Command Map page

Note: Remember to select OK to save any changes you make on the page.

Summary. The Summary feature lists what actions are currently assigned to each command. It lists

presets and tours separately, according to whichever list (preset or tour) you currently have selected under the Command feature.

Command. The Command feature changes the group of commands listed in the summary between presets

and tours.

Auxiliary input (for command). The Auxiliary input feature specifies the number of the command (for

example, Preset 2 or Preset 102) that is to be remapped.

Note: To see the title of the selected command, go to the corresponding summary or list under the Actions menu.

Assigned action. The Assigned action feature remaps the selected command (preset or tour) to the same

type of command or to another type of command (for example, from a preset to a tour or macro).

Auxiliary input (for assigned action). The Auxiliary input feature specifies the number of the command

that is assigned.

Note: To see the title of the selected command, go to the corresponding summary or list under the Actions menu.

Update. The Update feature remaps the selected command with the selected action.

Restored default. The Restore default feature unmaps all commands in the current list (preset or tour).

Any commands remapped in the other list (tour or preset) are not restored.

Page 95

Advanced programming

Chapter 5

Power-on and Resume page

The Power-on feature provides the ability to have an assigned operation performed by the dome every time the dome is powered up. The Resume feature provides the ability to have an assigned operation performed by the dome every time the dome has sat inactive for a specified period of time.

Actions versus commands

It will help you understand how to program your dome and how it is responding, if you understand the difference between actions and commands. Actions and commands are both dome operations. Some dome operations override others, however. Actions and commands can be distinguished by their function and priority. Actions are programmed operations, such as presets, ShadowTours, and macros. Commands are orders that come from protocol (control data transmission) devices, such as keypad controllers and alarm equipment. Protocol-based commands have priority over programmed actions.

While you are in the menus of the graphical programming interface, all of the dome’s programmed actions and protocol-based commands are disabled. While you are viewing live video, some dome operations take priority over others.

Priority of dome operations

The following list defines the priority of dome operations when the resume override is disabled.

1. Protocol-based commands: First priority is the manual control of the dome by any data protocol using any control device (keypad, ASCII control software, etc.). The control device sends protocolbased commands. Protocol-based commands (like pan, tilt, and zoom) will override all programmed dome actions (like presets, tours, and macros). When an alarm is occurring, protocol-based commands are a shared priority with alarms.

2. Alarms: Second priority is an alarm. Alarms generated by the dome will override all other programmed dome actions. When an alarm is occurring, it is a shared priority with joystick control after the instant that the alarm command is initiated. After an alarm is resolved, the timer for the resume operation begins.

3. Time scheduling and programmed actions: Third priority is any time schedule or action (preset, tour, or macro) that has been programmed for the dome.

4. Resume: Fourth priority is the programmed operation that resumes the dome after a period of dome inactivity.

5. Power-on: Fifth priority is the programmed operation that is performed by the dome after it is powered up.

If Resume overrides running operation is enabled (checkbox checked), then the resume operation moves from fourth priority to second priority. The priority of operations then becomes: protocol-based commands, resume, alarms, time scheduling and programmed actions, and power-on.

Page 96

Legend IP

User Manual

To access the Power-on and Resume page, select Control and Power-on and Resume.

Figure 64. Power-on and Resume page

Note: Remember to select OK to save any changes you make on the page.

Power-on operation. Power-on defines the first operation that the dome performs after it is powered up

and initialized. Choices are Off (default), Preset, Macro, ShadowTour, and Autopan.

Number (power-on operation). Enter a number for the operation selected under Power-on operation.

Choices are based on the selection made under Power-on operation.

Resume delay. Resume delay is a feature that sets how long the dome is inactive before the Resume

operation is performed. Choices are Off (default), 15 sec, 30 sec, 1 min, 2 min, 3 min, 4 min, and

5min.

Resume operation. Resume operation defines the operation for the dome to perform after the dome has

been inactive for a specified period of time. Choices are available only if a Resume delay time is selected and include Preset (default), Macro, ShadowTour, and Autopan.

Note: If the Resume overrides running operation feature is enabled (checkbox checked), then the Resume operation

feature will interrupt presets, tours, autopanning, and alarms. See Priority of dome operations on page 87.

Number (resume operation). Enter a number for the operation selected under Resume operation.

Choices are based on the selection made under Resume operation.

Resume overrides running operation. Resume overrides running operation is a feature that allows the

Resume operation feature to interrupt presets, tours, autopanning, and alarms. See Priority of dome

operations on page 87. Choices are checked and unchecked (default).

Page 97

Speeds/Tracking page

To access the Speeds/Tracking page, select Control and Speeds/Tracking.

Figure 65. Speeds/Tracking page

Advanced programming

Chapter 5

Note: Remember to select OK to save any changes you make on the page.

Max pan speed (deg/s). Max pan speed is a feature that sets the fastest the camera will move (in degrees

per second) while manually panning. Choices are 100 through 250 (default) in increments of 10.

Max tilt speed (deg/s). Max tilt speed is a feature that sets the fastest the camera will move (in degrees

per second) while manually tilting. Choices are 100 through 250 (default) in increments of 10.

Fast (deg/s). Fast is a feature that sets the speed at which the camera moves (in degrees per second) when

it is set for fast speed between presets in macros and while autopanning. Choices are 0 through 20 in increments of 2. Default is 16. A setting of 0 (degrees/second) makes the camera move as slowly as possible. This is not a stop-motion command.

Medium (deg/s). Medium is a feature that sets the speed at which the camera moves (in degrees per

second) when it is set for medium speed between presets in macros and while autopanning. Choices are 0 through 20 in increments of 2. Default is 10. A setting of 0 (degrees/second) makes the camera move as slowly as possible. This is not a stop-motion command.

Slow (deg/s). Slow is a feature that sets the speed at which the camera moves (in degrees per second)

when it is set for slow speed between presets in macros and while autopanning. Choices are 0 through 20 in increments of 2. Default is 4. A setting of 0 (degrees/second) makes the camera move as slowly as possible. This is not a stop-motion command.

Autopan speed. Autopan speed is a feature that sets how fast the camera moves while autopanning.

Choices are Slow (default), Medium, and Fast. These settings are scaled according to the settings set for the Slow, Medium, and Fast features of the Macro and autopan speed feature. If the numbers in the Macro and autopan speed boxes are lower, then the corresponding Autopan speed settings will be slower. For example, if the Fast feature setting of the Macro and autopan speed feature were

Page 98

Legend IP User Manual

set to 1, instead of 16, then the Fast feature setting of the Autopan speed feature would operate proportionately slower.

Enable proportional zoom operation. Proportional zoom is a feature that slows the pan and tilt speeds

as you zoom in. This makes it easier to follow far off moving targets when you are zoomed in to them. Choices are checked (default) to enable and unchecked to disable.

Enable zoom variable tilt. Zoom variable tilt is a feature that lowers the upper tilt limit when the camera

is zoomed out to a wide angle of view so that the trim ring of the dome is not in view. The feature raises the upper tilt limit when the camera zooms in to a narrower angle of view, because the trim ring recedes out of view. Choices are checked (default) to enable and unchecked to disable.

Enable electronic image flip

(E-flip). Electronic image flip (E-flip) is a feature that electronically flips the

video image when the camera is looking straight down so that the camera does not have to physically spin 180° to follow an object that is passing under the dome. Choices are checked (default) to enable and unchecked to disable.

Page 99

Advanced programming

Chapter 5

System menu

You can access diagnostics, status, and communication logs of your system’s features through the System menu pages. Under Diagnostics, you can see what temperature your dome is operating at. Under Status, you can see a detailed listing of your dome’s site (camera) information such as title and IP address, customized settings, alarm settings, and customized presets, tours, masks, and macros. Under Logs, you can see a history of the command, protocol, and motor messages being managed by the dome.

Figure 66. System menu

Page 100

Legend IP

User Manual

Diagnostics page

To access the Diagnostics page, select System and Diagnostics.

Camera tab

This page provides the operating temperature of your dome and allows you to enable SymSecure legacy support.

Figure 67. Camera tab

Temperature

This indicates the approximate temperature inside the dome.

SymSecure legacy support

If you select SymSecure legacy support, you must use SymSecure server v3.6 or earlier. In this mode, the Legend IP will emulate a SymNet, and gives a SymSecure more options. Configure the camera as if it were a SymNet.

If you do not select this, you can use SymSecure server v4.0 or later.