GE JD968, JS968 User Manual

Ranges
ge.com
JS968
JD968
Owner’s Manual
49-80317 07-05 JR
Write the model and serial numbers here:
Model
# ______________
Serial
# ______________
You can find them on a label behind the open oven door on the lower left corner of the range frame.
Self-Cleaning Convection
Safety Instructions . . . . . . . . .2–5

Operating Instructions

Baking or Roasting . . . . . . . . . .11
Broiling Guide . . . . . . . . . . . . . .12
Canning . . . . . . . . . . . . . . . . . . . .9
Clock and Timer . . . . . . . . . . . .13
Control Lockout . . . . . . . . . . . .13
Convection . . . . . . . . . . . . . .16–20
Cookware . . . . . . . . . . . . . . . . .8, 9
Oven . . . . . . . . . . . . . . . . . .10–28
Probe . . . . . . . . . . . . . . . . . . . . .15
Proofing . . . . . . . . . . . . . . . . . .21
Sabbath Feature . . . . . . . . . . . . .28
Self-Cleaning . . . . . . . . . . . .23, 24
Special Features . . . . . . . . . .25–27
Surface Units . . . . . . . . . . . . . 6, 7
Thermostat . . . . . . . . . . . . . . . .22
Timed Baking & Roasting . . . . .14
Warming . . . . . . . . . . . . . . . . . .21

Care and Cleaning

Broiler Pan and Grid . . . . . . . . 32
Control Panel . . . . . . . . . . . . . . 29
Door . . . . . . . . . . . . . . . . . . . . . 30
Floor . . . . . . . . . . . . . . . . . . . . .31
Glass Cooktop . . . . . . . . . . . 34, 35
Knobs . . . . . . . . . . . . . . . . . . . . 29
Light Bulb . . . . . . . . . . . . . . . . .31
Packaging Tape . . . . . . . . . . . . .29
Racks . . . . . . . . . . . . . . . . . . . . . 31
Storage Drawer . . . . . . . . . . . . . 32
Surfaces . . . . . . . . . . . . . . . . . . .33
Vent . . . . . . . . . . . . . . . . . . . . . 29
Troubleshooting Tips . . . . 36–39

Consumer Support

Consumer Support . . . Back Cover
Product Registration . . . . . . 41, 42
Warranty . . . . . . . . . . . . . . . . . . 43
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock, or to prevent property damage, personal injury, or loss of life.
All ranges can tip and injury could result.
Slide-In To prevent accidental tipping of the range, attach it to the wall and floor by installing the Ranges: Anti-Tip device supplied.
To check if the device is installed and engaged properly, remove the storage drawer and inspect the rear leveling leg. Make sure it fits securely into the slot.
Drop-In To prevent accidental tipping of the range, secure the attached Anti-Tip bracket, under Ranges: the rear countertop.
To check if the device is installed and engaged properly, lower the oven door and gently apply medium force at the handle end until movement of the range is detected. Continue pressing until the anti-tip bracket is engaged and movement stops. A small amount of movement is acceptable at the back of the range top but it should be stable and not tip once the anti-tip bracket is engaged.
If you pull the range out from the wall for any reason, make sure the device is properly engaged when you push the range back against the wall. If it is not, there is a possible risk of the range tipping over and causing injury if you or a child stand, sit or lean on an open door.
Please refer to the Anti-Tip device information in this manual. Failure to take this precaution could result in tipping of the range and injury.
WARNING ANTI-TIP DEVICE
IMPORTANT SAFETY NOTICE
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure to such substances.
The fiberglass insulation in self-clean ovens gives off a very small amount of carbon monoxide during the cleaning cycle. Exposure can be minimized by venting with an open window or using a ventilation fan or hood.
When using electrical appliances, basic safety precautions should be followed, including the following:
Use this appliance only for its intended
purpose as described in this Owner’s Manual.
Be sure your appliance is properly
installed and grounded by a qualified installer in accordance with the provided installation instructions.
Have the installer show you the location of
the circuit breaker or fuse. Mark it for easy reference.
Do not attempt to repair or replace any
part of your range unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.
Before performing any service, disconnect
the range power supply at the household distribution panel by removing the fuse or switching off the circuit breaker.
Do not leave children alone—children
should not be left alone or unattended in an area where an appliance is in use. They should never be allowed to sit or stand on any part of the appliance.
Do not allow anyone to climb, stand or
hang on the door, storage drawer or cooktop. They could damage the range and even tip it over, causing severe personal injury.
SAFETY PRECAUTIONS
2

Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

ge.com
Do not store flammable materials in an
oven or near the cooktop.
CAUTION: Items of interest to
children should not be stored in cabinets above a range or on the back of a range— children climbing on the range to reach items could be seriously injured.
Never wear loose-fitting or hanging
garments while using the appliance. Be careful when reaching for items stored over the range. Flammable material could be ignited if brought in contact with hot surface units or heating elements and may cause severe burns.
Use only dry pot holders—moist or damp
pot holders on hot surfaces may result in burns from steam. Do not let pot holders touch hot surface units or heating elements. Do not use a towel or other bulky cloth in place of pot holders.
Do not use water on grease fires. Never
pick up a flaming pan. Turn the controls off. Smother a flaming pan on a surface unit by covering the pan completely with a well-fitting lid, cookie sheet or flat tray. Use a multi-purpose dry chemical or foam-type fire extinguisher.
Flaming grease outside a pan can be put
out by covering it with baking soda or, if available, by using a multi-purpose dry chemical or foam-type fire extinguisher.
Flame in the oven can be smothered
completely by closing the oven door and turning the oven off or by using a multi-purpose dry chemical or foam-type fire extinguisher.
For your safety, never use your appliance
for warming or heating the room.
Do not let cooking grease or other
flammable materials accumulate in or near the range.
Do not touch the surface units, the
heating elements or the interior surface of the oven. These surfaces may be hot enough to burn even though they are dark in color. During and after use, do not touch, or let clothing or other flammable materials contact the surface units, areas nearby the surface units or any interior area of the oven; allow sufficient time for cooling first.
Potentially hot surfaces include the
cooktop, areas facing the cooktop, oven vent opening, surfaces near the opening, crevices around the oven door.
REMEMBER: The inside surface of the oven
may be hot when the door is opened.
Do not store or use combustible materials,
gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Keep the hood and grease filters clean
to maintain good venting and to avoid grease fires.
Teach children not to play with the
controls or any other part of the range.
Always keep dish towels, dish cloths, pot
holders and other linens a safe distance from your range.
Always keep wooden and plastic utensils
and canned food a safe distance from your range.
Always keep combustible wall coverings,
curtains or drapes a safe distance from your range.
WARNING!
SAFETY PRECAUTIONS
Cook meat and poultry thoroughly—meat to at least an INTERNAL temperature of 160°F and poultry to at least an INTERNAL temperature of 180°F. Cooking to these temperatures usually protects against foodborne illness.
COOK MEAT AND POULTRY THOROUGHLY…
Do not operate the oven or cooktop controls if the glass is broken. Food splatter or cleaning solution may penetrate a broken control panel or cooktop and create a risk of electrical shock. Contact a qualified technician immediately should your glass control panel or cooktop become broken.
Safety Instructions
Operating Instructions
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips
Consumer Support
3
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.
Use proper pan size—select cookware having flat bottoms large enough to cover the surface unit heating element. The use of undersized cookware will expose a portion of the surface unit to direct contact and may result in ignition of clothing. Proper relationship of cookware to surface unit will also improve efficiency.
Never leave the surface units unattended
at high heat settings. Boilovers cause smoking and greasy spillovers that may catch on fire.
Only certain types of glass, glass ⁄ceramic,
earthenware or other glazed containers are suitable for cooktop service; others may break because of the sudden change in temperature.
To minimize the possibility of burns,
ignition of flammable materials and spillage, the handle of a container should be turned toward the center of the range without extending over nearby surface units.
Always turn the surface units off before
removing cookware.
When preparing flaming foods under
the hood, turn the fan on.
Use care when touching the cooktop. The
glass surface of the cooktop will retain heat after the controls have been turned off.
Keep an eye on foods being fried at high
or medium high heat settings.
Foods for frying should be as dry as
possible. Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan.
Use little fat for effective shallow or deep
fat frying. Filling the pan too full of fat can cause spillovers when food is added.
If a combination of oils or fats will be used
in frying, stir together before heating, or as fats melt slowly.
Always heat fat slowly, and watch as it heats.
Use a deep fat thermometer whenever
possible to prevent overheating fat beyond the smoking point.
Avoid scratching the glass cooktop. The
cooktop can be scratched with items such as sharp instruments, rings or other jewelry, and rivets on clothing.
Large scratches or impacts to glass doors
or cooktops can lead to broken or shattered glass.
Do not operate the radiant surface units if
the glass is broken. Spillovers or cleaning solution may penetrate a broken cooktop and create a risk of electrical shock. Contact a qualified technician immediately should your glass cooktop become broken.
Never use the glass cooktop surface as a
cutting board.
Do not place or store items that can melt
or catch fire on the glass cooktop, even when it is not being used.
Be careful when placing spoons or other
stirring utensils on glass cooktop surface when it is in use. They may become hot and could cause burns.
Clean the cooktop with caution. If a wet
sponge or cloth is used to wipe spills on a hot surface unit, be careful to avoid steam burns. Some cleaners can produce noxious fumes if applied to a hot surface.
NOTE: We recommend that you avoid wiping any surface unit areas until they have cooled and the indicator light has gone off. Sugar spills are the exception to
this. Please see the Cleaning the glass cooktop section.
When the cooktop is cool, use only the
CERAMA BRYTE
®
Ceramic Cooktop Cleaner and the CERAMA BRYTE Ceramic Cooktop Cleaning Pad to clean the cooktop.
To avoid possible damage to the cooking
surface, do not apply cleaning cream to the glass surface when it is hot.
After cleaning, use a dry cloth or paper
towel to remove all cleaning cream residue.
Read and follow all instructions and
warnings on the cleaning cream labels.
RADIANT SURFACE UNITS
4
Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions
Safety Instructions
Operating Instructions
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips
Consumer Support
5
ge.com
Do not heat unopened food containers.
Pressure could build up and the container could burst, causing an injury.
Keep the oven vent unobstructed.
Keep the oven free from grease buildup.
Place the oven rack in the desired position
while the oven is cool. If racks must be handled when hot, do not let pot holder contact the heating elements.
When using cooking or roasting bags in
the oven, follow the manufacturer’s directions.
Pulling out the rack to the stop-lock is a
convenience in lifting heavy foods. It is also a precaution against burns from touching hot surfaces of the door or oven walls.
Do not use the oven to dry newspapers.
If overheated, they can catch on fire.
Do not use the oven for a storage area.
Items stored in an oven can ignite.
Do not leave paper products, cooking
utensils or food in the oven when not in use.
Do not use aluminum foil to line oven
bottoms, except as suggested in this manual. Improper installation of aluminum foil may result in a risk of electric shock or fire.
Stand away from the range when opening the oven door. Hot air or steam which escapes can cause burns to hands, face and/or eyes.
WARNING!
OVEN
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
Do not use oven cleaners. No commercial oven cleaner or oven liner protective coating of any kind should be used in or around any part of the oven. Residue from oven cleaners will damage the inside of the oven when the self-clean cycle is used.
Do not clean the door gasket. The door
gasket is essential for a good seal. Care should be taken not to rub, damage or move the gasket.
Before self-cleaning the oven, remove
the racks, broiler pan, grid and other cookware.
Be sure to wipe up excess spillage before
starting the self-cleaning operation.
If the self-cleaning mode malfunctions,
turn the oven off and disconnect the power supply. Have it serviced by a qualified technician.
Clean only parts listed in this Owner’s
Manual.
SELF-CLEANING OVEN
Using the surface units.
NOTE: Throughout this manual, features and appearance may vary from your model.
How to Set
Push the knob in and turn in either direction to the setting you want.
At both OFF and HI the control clicks into position. You may hear slight clicking sounds during cooking, indicating the control is keeping the power level you set.
A HOT SURFACE indicator light, on the cooktop, will glow when any radiant element is turned on. It will remain on until the surface is cooled to approximately 150°F.
Hot surface indicator light will:
come on when the unit is hot to the touch.
stay on even after the unit is turned off.
glow until the unit is cooled to approximately
150°F.
The WARM setting on the right REAR surface unit keeps already heated food warm until ready to serve. Do not use to heat cold food.
Do not slide cookware across the cooktop because it can scratch the glass—the glass is scratch-resistant, not scratch-proof.
Temperature Limiter
Every radiant surface unit has a temperature limiter.
The temperature limiter protects the glass cooktop from getting too hot.
The temperature limiter may cycle the units off for a time if:
The pan boils dry.
The pan bottom is not flat.
The pan is off center.
There is no pan on the unit.
7
Safety Instructions
Operating Instructions
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips
Consumer Support
Using the tri-ring surface unit
The right front Tri-Ring surface unit has 3 sizes to select from so you can match the size of the unit to the size of the cookware you are using.
To use the large surface unit, press and turn the right front control knob clockwise to , stopping at the desired setting. This will activate the entire heating area.
To use the medium surface unit, press and turn the right front control
knob clockwise to , stopping at the desired setting. This will activate the medium-size heating area.
To use the smallest surface unit, press and turn the right front control knob clockwise to ,stopping at the desired setting. This will activate the smallest, inside heating area.
HI
6
3
LO
HI
6
LO
3
6
HI
LO
3
DRAGGING
Selecting types of cookware.
The following information will help you choose cookware which will give good performance on glass cooktops.
Stainless Steel:
recommended
Aluminum:
heavyweight recommended
Good conductivity. Aluminum residues sometimes appear as scratches on the cooktop, but can be removed if cleaned immediately. Because of its low melting point, lightweight aluminum should not be used.
Copper Bottom:
recommended
Copper may leave residues which can appear as scratches. The residues can be removed, as long as the cooktop is cleaned immediately. However, do not let these pots boil dry. Overheated metal can bond to glass cooktops. An overheated copper bottom pot will leave a residue that will permanently stain the cooktop if not removed immediately.
Porcelain Enamel-Covered Cast Iron:
recommended
As long as the cookware is covered completely with porcelain enamel, this cookware is recommended. Caution is recommended for cast iron cookware that is not completely covered with smooth porcelain enamel, since it may scratch the glass ceramic cooktop.
Glass-Ceramic:
usable, but not recommended
Poor performance. May scratch the surface.
Stoneware:
usable, but not recommended
Poor performance. May scratch the surface.
Home Canning Tips:
Be sure the canner is centered over the surface unit.
Make sure the canner is flat on the bottom.
Use recipes and procedures from reputable sources. These are available from manufacturers such as Ball®and Kerr®and the Department of Agriculture Extension Service.
To prevent burns from steam or heat, use caution when canning.
Check pans for flat bottoms by using a straight edge.
Pans with rounded, curved, ridged or warped bottoms are not recommended.
Use only flat-bottomed woks.
Wok Cooking
We recommend that you use only a flat-bottomed wok. They are available at your local retail store.
Do not use round-bottom woks. You could be seriously burned if the wok tipped over.
8
Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions
9
Note: Flat-bottomed canners are required for glass cooktops.
Pots that extend beyond 1″ of the surface unit’s circle are not recommended for most surface cooking. However, when canning with water-bath or pressure canner, larger-diameter pots may be used. This is because boiling water temperatures (even under pressure) are not harmful to the cooktop surfaces surrounding the surface units.
HOWEVER, DO NOT USE LARGE­DIAMETER CANNERS OR OTHER LARGE-DIAMETER POTS FOR FRYING OR BOILING FOODS OTHER THAN WATER. Most syrup or sauce mixtures—and all types of frying—cook at temperatures much higher than boiling water. Such temperatures could eventually harm the glass cooktop surfaces.
Be sure the canner fits over the center of the surface unit. If your cooktop or its location does not allow the canner to be centered on the surface unit, use smaller­diameter pots for good canning results.
Flat-bottomed canners must be used. Do not use canners with flanged or rippled bottoms (often found in enamelware) because they don’t make enough contact with the surface units and take a long time to boil water.
When canning, use recipes and procedures from reputable sources. Reliable recipes and procedures are available from the manufacturer of your canner; manufacturers of glass jars for canning, such as Ball®and Kerr
®
brand; and the United States Department of Agriculture Extension Service.
Remember that canning is a process that generates large amounts of steam. To avoid burns from steam or heat, be careful when canning.
NOTE: If your house has low voltage, canning may take longer than expected, even though directions have been carefully followed. The process time will be shortened by:
(1) using a pressure canner, and
( 2) starting with HOT tap water for fastest
heating of large quantities of water.
CAUTION:
Safe canning requires that harmful
microorganisms are destroyed and that the jars are sealed completely. When canning foods in a water-bath canner, a gentle but steady boil must be maintained for the required time. When canning foods in a pressure canner, the pressure must be maintained for the required time.
After you have adjusted the controls,
it is very important to make sure the prescribed boil or pressure levels are maintained for the required time.
Since you must make sure to process
the canning jars for the prescribed time, with no interruption in processing time, do not can on any cooktop surface unit if your canner is not flat.
Observe the Following Points in Canning
Wrong!
Right!
ge.com
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips
Consumer Support
Aluminum Foil
You can use aluminum foil to line the broiler pan and broiler grid. However, you must mold the foil tightly to the grid and cut slits in it just like the grid.
Without the slits, the foil will prevent fat and meat juices from draining into the broiler pan. The juices could become hot enough to catch on fire. If you do not cut the slits, you are essentially frying, not broiling.
Do not use aluminum foil on the bottom of the oven.
Never entirely cover a rack with aluminum foil. This will disturb the heat circulation and result in poor baking.
A smaller sheet of foil may be used to catch a spillover by placing it on a lower rack several inches below the food.
12
Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions
Using the oven.
How to Set the Oven for Broiling
Leave the door open to the broil stop position. The door stays open by itself, yet the proper temperature is maintained in the oven.
NOTE: Food can be broiled with the door closed, but it may not brown as well because the oven heating element will cycle on and off.
Place the meat or fish on the broiler grid in the broiler pan.
Follow suggested rack positions in the Broiling Guide.
Touch the BROIL HI/LO pad once for
HI Broil. To change to LO Broil, touch the
BROIL HI/LO pad again.
Use LO Broil to cook foods such as poultry or thick cuts of meat thoroughly without over-browning them.
Touch the START pad. When broiling is finished, touch the
CLEAR/OFF pad.
NOTE: Broil will not work if the temperature
probe is plugged in.
The size, weight, thickness, starting temperature and your preference of doneness will affect broiling times. This guide is based on meats at refrigerator temperature.
The U.S. Department of
Agriculture says “Rare beef is popular, but you should know that cooking it to only 140°F means some food poisoning organisms may survive.” (Source: Safe Food Book. Your Kitchen Guide
. USDA
Rev. June 1985.)
If your range is connected to 208 volts, rare steaks may be broiled by preheating the broiler and positioning the oven rack one position higher.

Broiling Guide

Quantity and/ Shelf First Side Second Side
Food or Thickness Position Time (min.) Time (min.) Comments
Ground Beef 1 lb. (4 patties) E 9 6 Space evenly. Up to 8
Well Done 1/2 to 3/4thick E 11 10 patties take about the
same time.
Beef Steaks
Rare† 1thick F 7 5 Steaks less than 1 Medium 1 to 11⁄2
lbs. E 9 6–7 thick cook through
Well Done E 11 8–9 before browning. Pan
frying is recommended. Slash fat.
Rare† 1
1
2thick D 14 11 Medium 2 to 21⁄2 lbs. D 18 14–16 Well Done D 22 20
Chicken 1 whole cut up C 25 10 Broil skin-side-down
2 to 21⁄2 lbs., first. split lengthwise 2 Breasts C 25 10–15
Lobster Tails 2–4 C 18–20 Do not Cut through back of
10 to 12 oz. each turn shell. Spread open.
over. Brush with melted
butter before broiling and after half of broiling time.
Fish Fillets 1/4 to 1/2thick E 6 5 Handle and turn very
carefully. Brush with lemon butter before and during cooking, if desired.
Ham Slices 1/2thick D 6 6 Increase time 5 to 10 (precooked) minutes per side for
11⁄2″ thick or home- cured ham.
Pork Chops 2 (1/2thick) E 10 10 Slash fat. Well Done 2 (1thick) about 1 lb. D 15 15
Lamb Chops
Medium 2 (1thick) about 10 E 8 7–8 Slash fat. Well Done to 12 oz. E 10 9–10
Medium 2 (11⁄2thick) about 1 lb. E 14 12 Well Done E 17 12–14
Salmon Steaks 2 (1thick) D 10 7–8 Grease pan. Brush
4 (1thick) about 1 lb. D 12 10 steaks with melted
butter.
The oven has 7 shelf positions.
Safety Instructions
Operating Instructions
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips
Consumer Support
Using the clock, timer and control lockout.
ge.com
To Set the Clock
The clock must be set to the correct time of day for the automatic oven timing functions to work properly. The time of day cannot be changed during a timed baking or self-cleaning cycle.
Touch the CLOCK pad. Touch the number pads. Touch the START pad.
14
Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions
Using the timed baking and roasting features.
NOTE: Foods that spoil easily—such as milk, eggs, fish, stuffings, poultry and pork—should not be allowed to sit for
more than 1 hour before or after cooking. Room temperature promotes the growth of harmful bacteria. Be sure that the oven light is off because heat from the bulb will speed harmful bacteria growth.
How to Set an Immediate Start and Automatic Stop
The oven will turn on immediately and cook for a selected length of time. At the end of the cooking time the oven will turn off automatically.
Touch the BAKE pad. Using the number pads, enter the
desired temperature. Touch the COOK TIME pad.
NOTE: If your recipe requires preheating, you may need to add additional time to the length of the cooking time.
Using the number pads, enter the desired baking time. The oven temperature and the cooking time that you entered will be displayed.
Touch the START pad.
The display will show the changing temperature (starting at 100ºF) and the cooking time. The display starts changing once the temperature reaches 100ºF.
The oven will continue to cook for the programmed amount of time, then shut off automatically, unless the WARM feature was set. See the How to Set the Oven for Warming section.
Touch the CLEAR/OFF pad to clear the display.
How to Set a Delayed Start and Automatic Stop
You can set the oven control to delay-start the oven, cook for a specific length of time and then turn off automatically.
Make sure the clock shows the correct time of day.
Touch the BAKE pad. Using the number pads, enter the
desired temperature. Touch the COOK TIME pad.
NOTE: If your recipe requires preheating, you may need to add additional time to the length of the cooking time.
Using the number pads, enter the desired baking time.
Touch the DELAY START pad. Using the number pads, enter the
time of day you want the oven to turn on and start cooking.
Touch the START pad.
NOTE: An attention tone will sound if you are using timed baking and do not touch the START pad after entering the baking temperature.
If you would like to check the times you have set, touch the DELAY START pad to check the start time you have set or touch the COOK TIME pad to check the length of cooking time you have set.
When the oven turns on at the time of day you have set, the display will show the changing temperature (starting at 100ºF) and the cooking itme. The display starts changing once the temperature reaches 100ºF.
The oven will continue to cook for the programmed amount of time, then shut off automatically, unless the WARM feature was set. See the How to Set the Oven for Warming section.
Touch the CLEAR/OFF pad to clear the display.
Loading...
+ 30 hidden pages