GE GXCF20E, GXCF20FBB User Manual

www.GEAppliances.com

Hot & Cold Water Dispenser

215C1002P013 49-50095-5 07-04 JR

Safety Instructions . . . . . . . . . . . . . . . . . . . .2, 3

Using the Water Dispenser

Child Safeguard . . . . . . . . . . . . . . . . . . . . . . . . . .5

Cold Water and Compartment

Temperature Adjustment . . . . . . . . . . . . . . . . . .5

Features and Parts List . . . . . . . . . . . . . . . . . . . .4

Loading the Dispenser . . . . . . . . . . . . . . . . . . . .4

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Care and Cleaning . . . . . . . . . . . . . . . . . . . . . .5–8

Troubleshooting Tips . . . . . . . . . . . . . . . . . . . .8, 9

Consumer Support

Consumer Support . . . . . . . . . . . . . . .Back Cover

Warranty . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Français

Informations en matière de sécurité . . . . . . .10, 11

Utilisation du distributeur d’eau

Caractéristiques et liste de pièces . . . . . . . . . . .12

Caractéristiques techniques . . . . . . . . . . . . . . .16

Chargement du distributeur . . . . . . . . . . . . . .13

Réglage de la température de l’eau

froide et du compartiment . . . . . . . . . . . . . . . .13

Sauvegarde pour la protection des enfants . . .13

Entretien et nettoyage . . . . . . . . . . . . . . . . . .13–16

Conseils de dépannage . . . . . . . . . . . . . . . . .16, 17

Soutien du consommateur

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Soutien du consommateur . . . . . . . . . . . . . . . .18

Español

Información de seguridad . . . . . . . . . . . . . .19, 20

Cómo utilizar el dispensador de agua

Ajuste del agua fría y de la

temperatura del compartimiento . . . . . . . . . . .22

Cómo cargar el dispensador . . . . . . . . . . . . . . .22

Especificaciones . . . . . . . . . . . . . . . . . . . . . . . . .25

Lista de partes y características . . . . . . . . . . . . .21

Seguro contra niños . . . . . . . . . . . . . . . . . . . . .22

Cuidado y limpieza . . . . . . . . . . . . . . . . . . .22–25

Solucionar problemas . . . . . . . . . . . . . . . . .25, 26

Apoyo al consumidor

Garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Apoyo al consumidor . . . . . . . . . . . . . . . . . . . .27

GXCC01D* countertop model

GXCF05D* floor model

GXCF20E/GXCF20FBB

chiller model

Owner’s Manual

La section française commence à la page 10

La sección en español empieza en la página 19

Distributeur d’eau

chaude ou froide

Dispensador de agua

caliente & fría

Manuel d’utilisation

Manual del propietario

As an ENERGY STAR®partner, GE has determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

*ENERGY STAR®qualified product.

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

PROPER INSTALLATION AND LOCATION

■

■ Allow at least 1″ (2.5 cm) of space between the

back of the water dispenser and the wall to allow for proper air circulation.

■

■ Do not install the water dispenser where the

temperature will go below 50°F (10°C) or above 100°F (38°C).

■

■ Install the water dispenser on a level floor or

counter strong enough to support it when fully loaded. Do not install where it will be subject to direct sunlight, heat or moisture.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This water dispenser must be properly installed

and located in accordance with these instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the outside of the dispenser, or on the shelves inside the storage cabinet (on some models). They could tip the dispenser over and damage it and seriously injure themselves.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other appliance.

■

■ Unplug the water dispenser before cleaning or

making repairs.

NOTE: GE does not support any servicing of the dispenser. We strongly recommend that you do not attempt to service the dispenser yourself.

■

■ Do not use this dispenser to dispense anything

other than water.

■

■ Do not plug in the power cord or turn on the power

switches when the water dispenser is empty.

■

■ Wipe up any water spills immediately after loading

or unloading water bottles.

■

■ Children should be supervised by a parent when

using this product.

■

WARNING: Do not use with water that is

microbiologically unsafe or of unknown quality.

■

CAUTION: The dispenser heats water

to a temperature of approximately 190°F (88°C). Water temperatures above 125°F (52°C) can cause severe burns or death from scalding. Children, the disabled and the elderly are at highest risk of being scalded.

■

NOTICE: This product is intended solely for

use in chilling canned and boxed beverages, and packaged nonperishables.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock.

This appliance is equipped with a power cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

Do not under any circumstances cut or remove the third (ground) prong from the power cord.

Do not use an adapter plug with this appliance.

Do not use an extension cord with this appliance. If the power cord is too short, have a qualified electrician install an outlet near the appliance.

For best operation, plug the appliance into its own electrical outlet on a dedicated circuit to prevent flickering of lights, blowing of fuse, or tripping of circuit breaker.

WARNING: Improper use of the grounding plug can result in a risk of electric shock.

PROPER DISPOSAL OF THE WATER DISPENSER

Refrigerant Disposal

Your old water dispenser may have used a regulated refrigerant in its cooling system. These refrigerants are believed to harm stratospheric ozone. If you are throwing away your old dispenser, make sure the refrigerant is removed and recovered for proper disposal by an EPA-certified technician. If you intentionally release this refrigerant, you can be subject to fines and imprisonment under provisions of environmental legislation.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

IMPORTANT: Make sure the dispenser is unplugged with

both the hot and cold power switches (on the back of the dispenser) set to the O (off) position. Before placing the water bottle on the dispenser, wash hands and wipe the top of the bottle with a clean cloth. Avoid touching the part of the bottle that will be in contact with the water dispenser.

Make sure the water level in the top of the dispenser is low enough to allow for proper bottle installation. Failure to do so may cause the dispenser to overflow.

Sanitize the dispenser water tanks prior to installing a full bottle of water for the first time (see “Cleaning and Sanitizing the Water Tanks”).

1. Peel the label from the top cover of the bottle.

Do not remove the entire bottle cap or press in the center plug.

2. Place the bottle on top of the dispenser as shown, aligning the center plug with the probe. Press down until the probe pushes the center plug out of the cap and into the water bottle, allowing the bottle to rest on the support collar. The plug may remain on top of the probe or may be released to float in the water; both conditions are normal.

3. IMPORTANT: Press the hot and cold dispenser buttons until water runs from both taps.

4. Plug in the dispenser.

5. Set the HOT and COLD power switches (located

on the top left rear of the dispenser) to the I (on) position.

6. Allow 30 minutes for water to reach hot and cold temperatures.

Contact a local water bottle distributor to purchase water bottles.

Loading the Dispenser and Start Up

Using the water dispenser.

Features and Parts List

Bottle Support Collar (WS28X10038), grey for models GXCF05D and GXCC01D

Bottle Support Collar (WS28X10036), white for model GXCF20E, (WS28X10035) black for model GXCF20FBB

Separator (WS28X10013)

Cold Water Tank

Hot (Red) and Cold (Blue) Power Switches (back of dispenser). The Cold (Blue) power switch also turns

on the chiller compartment (on model GXCF20E). Indicator Lights. The green light will be lit when the

dispenser is plugged in. The red and blue lights will cycle on and off while the dispenser heats and cools water. Compressor start delayed by up to 3 minutes.

Hot (Red) and Cold (Blue) Water Dispenser Buttons

Dispenser Drip Tray (WS28X10016) and Grille (WS28X10015), grey for models GXCF05D and GXCC01D

Dispenser Drip Tray (WS28X10026) and Grille (SW28X10027) white for model GXCF20E

Dispenser Drip Tray (WS28X10031) and Grille (WS28X10034) black for model GXCF20FBB

Compartment Tray (model GXCF20E/GXCF20FBB only) (WS29X10029)

Storage Compartment (GXCF05D). Do not use to store

foods requiring refrigeration. The compartment is not refrigerated.

Chiller Compartment (GXCF20E). The compartment is intended solely for use in chilling canned and boxed beverages, and packaged nonperishables.

Compartment Shelf (WS28X10028)

Drainage Cap (floor and chiller models) (WS01X10008)

Silicon Stopper (floor and chiller models) (WS01X10007)

Retaining Clip (countertop models) (WS01X10010)

Rubber Drain Cover (countertop models) (WS01X10011)

GXCF05D

Floor model

GXCF20E/GXCF20FBB

Chiller model

GXCC01D

Countertop model

Drip tray

Drip tray grille

Child

safeguard

tab

The HOT dispenser button is equipped with a child safeguard that reduces the risk of hot water being dispensed accidentally or by small children. To use the button, slide the tab up and press the button in.

The dispenser heats water to a temperature of approximately 190°F (88°C). Water temperatures above 125°F (52°C) can cause severe burns or death from scalding. Children, the disabled and the elderly are at highest risk of being scalded.

CAUTION: Children should be supervised

by a parent when using this product.

Child Safeguard

Care and cleaning of the dispenser.

IMPORTANT: Set both power switches (on the

back of the dispenser) in the O (off) position and unplug the water dispenser before cleaning.

The cabinet and compartment of the dispenser can be washed with mild soap and water. Rinse thoroughly with clear water. Never use commercial cleaners or abrasive scouring powders.

Sweep away or vacuum any dust from the condenser coils on the back of the unit. For best results, use a brush specially designed for this purpose. It is available at most appliance stores.

Cleaning the Outside Cabinet and Storage/Chiller Compartment (on some models)

To help prevent odors, leave an open box of

baking soda in the chiller compartment.

Unplug the dispenser before cleaning.

Use warm water and baking soda solution— about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and neutralizes odors. Rinse and wipe dry.

Clean other parts of the chiller compartment— including door gaskets and all plastic parts— the same way.

Do not wash any plastic chiller parts in the dishwasher.

Cleaning the Inside of the Chiller Compartment (GXCF20E/GXCF20FBB)

The dispenser drip tray is not self-draining. To reduce water spotting or deposits, the tray and its grille should be emptied, cleaned and wiped dry regularly.

Clean with mild soap or on the top rack in the dishwasher.

Cleaning the Drip Tray and Grille

Separator

Support collar

To remove To replace

Drain outlet cap

Floor models

(rear of dispenser)

Floor Models

1. Set both power switches (on the back of the dispenser) in

the O (off) position and unplug the dispenser.

2. Remove the water bottle from the dispenser.

3. Put a container that will withstand hot water under the hot water tap. Press the hot dispenser button until the water is cool (about 1 quart). Add water to the cold water reservoir

(on top where the bottle supplies water) as needed.

4. Dispense water from both buttons into container(s) until no more water can be dispensed (about 1 quart of water still remains in the dispenser).

5. Place a large bucket beneath the drain outlet on the rear of the dispenser.

6. Using a Phillips screwdriver, loosen the screws on the bracket covering the drain outlet cap. Rotate the bracket out of the way to allow access to the cap.

7. Remove the cap and silicon stopper from the drain outlet and and allow water to drain. After draining, replace the

stopper and cap.

8. Rotate the bracket back into place and tighten screws.

Make sure to install a full bottle and dispense water from the hot water tap before plugging in and turning on the dispenser (see Loading the Dispenser).

Countertop Models

1. Set both power switches (on the back of the dispenser) in

the O (off) position and unplug the dispenser.

2. Remove the water bottle from the dispenser.

3. Put a container that will withstand hot water under the hot water tap. Press the hot dispenser button until the water is cool (about 1 quart). Add water to the cold water reservoir

(on top where the bottle supplies water) as needed.

4. Dispense water from both buttons into container(s) until no more water can be dispensed (about 1 quart of water still remains in the dispenser).

WARNING:

Lift the dispenser carefully; it weighs approximately 40 lbs (18 kg). Avoid accidentally pressing the dispenser buttons while lifting or carrying.

5. Place the dispenser over a sink with 3 feet on the counter.

Hold or secure the dispenser steady while removing the retaining clip and drain cover. Remove the retaining clip and drain cover from the drain outlet, making sure not to damage the drain cover. Allow water to drain.

6. After draining, replace the drain cover and retaining clip.

Make sure to install a full bottle and dispense water from the hot water tap before plugging in and turning on the dispenser (see Loading the Dispenser).

Drain cover and

retaining clip

Countertop models

(bottom of dispenser)

Care and cleaning of the dispenser.

The dispenser should be drained before cleaning the tanks and before leaving for long vacations or absences.

Draining the Dispenser

IMPORTANT: Set both power switches (on the

back of the dispenser) in the O (off) position and unplug the water dispenser before cleaning.

1. Remove the water bottle and drain the

dispenser (see Draining the Dispenser).

2. Remove the support collar by turning counterclockwise and pulling straight off.

3. Remove the plastic separator by pulling

straight out (you may need to twist slightly to loosen).

4. Clean the separator with dish soap and water or in the top rack of the dishwasher.

5. Dry the separator thoroughly on both sides.

6. Using a clean cloth or paper towel,

thoroughly dry the cold water reservoir.

7. Place the separator back in the dispenser. Make sure the long, tapered end of the separator is positioned firmly on the metal plug on the bottom of the reservoir.

8. Replace the support collar and turn clockwise until it is firmly in place.

9. Install a full water bottle on the dispenser

(see Loading the Dispenser).

Cleaning the Separator

To Sanitize:

11. Before cleaning, set both power switches (on the

back of the dispenser) in the O (off) position and

unplug the water dispenser. NOTE: For first time installation, skip steps 2–4.

12. Empty the water bottle, then remove it from the dispenser.

13. Drain the water tanks (see Draining the Dispenser).

14. Reinstall the silicon stopper and drain cap (on floor models)

or the drain cover and retaining clip (on countertop models)

(see Draining the Dispenser).

15. DO NOT ADD BLEACH FIRST OR DIRECTLY TO THE DISPENSER.

Concentrated bleach may damage plastic.

Add 1/2 teaspoon (2.5 ml) of ordinary 6.0% maximum household bleach to a 2 quart (2 liter) pitcher filled with tap water.

16. Pour the solution in the opening at the top of the

dispenser.

17. Repeat steps 5 and 6 until the dispenser is full.

18. Press the hot and cold dispenser buttons until the water

just begins to flow from the taps.

19. Allow to sit for 15–20 minutes.

10. Rinse out the bleach solution:

— Drain the water tanks into a large bucket (floor models)

or sink (countertop models) (see Draining the Dispenser).

— Make sure that the silicon stopper (floor models) or

drain cover (countertop models) is NOT installed.

— IMPORTANT: Remove the separator and wipe out the cold

water reservoir (see Cleaning the Separator).

— Clean, then reinstall the separator and collar

(see Cleaning the Separator).

— Pour approximately 1 gallon (4 quarts or 4 liters) of

fresh tap water into the top and allow to drain into the bucket (floor models) or sink (countertop models).

— Flush with an additional 1 gallon (4 quarts or 4 liters)

of fresh tap water and allow to drain into the bucket (floor models) or sink (countertop models).

11. Reinstall the silicon stopper and drain cap (on floor models) or the drain cover and retaining clip (on countertop models)

(see Draining the Dispenser).

12. Install a fresh water bottle (see Loading the Dispenser).

13. Dispense 1 quart (1 liter) of water from each tap and taste to

make sure the bleach solution is completely removed.

If you continue to taste the chlorine from the bleach solution, repeat steps 10–13 until the taste is gone.

14. Plug in the dispenser. Then turn on the hot and cold power switches (on the back of the dispenser).

To Remove Mineral Deposits:

Mix 2 quarts (2 liters) of water with two quarts of vinegar OR mix 1 gallon of water (4 liters) with 16 ounces (454 g) of citric acid crystals. Bleach does not remove mineral deposits. Do this in place of step 5 when removing mineral deposits.

OFF

position

IMPORTANT: Periodically the water dispenser tanks must be sanitized to prevent unpleasant tastes in the water and cleaned to remove mineral deposits that can impair flow.

Sanitizing and Cleaning the Water Tanks

position

Defrost whenever frost on the wall of the chiller compartment becomes excessive. Never use a sharp

or metallic instrument to remove frost as it may damage the liner. We recommend using a plastic

scraper. Do not use any electrical device in defrosting your chiller compartment.

To defrost:

■ Remove items from the compartment.

■ Turn the Cold (Blue) Power switch to off and

unplug the dispenser.

■ Put several towels in the bottom of the

compartment to collect water.

Defrosting usually takes a few hours. To defrost faster, keep the door open.

After defrosting:

■ Remove the wet towels and wipe up any

remaining water.

■ Wipe the compartment with a dry cloth.

■ Plug in the unit and turn on the Cold (Blue)

power switch. Return items to the unit.

Defrosting (GXCF20E/GXCF20FBB Chiller Model)

Problem Possible Causes What To Do

Water has poor taste Separator needs cleaning. •See Cleaning the Separator. or odor

Unit needs to be sanitized. •See Cleaning and Sanitizing the Water Tanks.

Water not hot enough Dispenser is unplugged. • Push the plug completely into the outlet. or cold enough

The fuse is blown/circuit • Replace house fuse or reset the house circuit breaker. breaker is tripped. • If too many items are plugged into a single circuit, move some

items to a different circuit.

All the water in the water tank •Wait 30 minutes for water to heat or cool. has been used.

Temperature limiter tripped. •Set the hot and cold power switches (on the back of the

dispenser) to the O (off) position. Wait five minutes; then set the switches to the I (on) position. Wait 30 minutes for water to heat or cool.

Water dispenser does Empty water bottle. •Replace with a new bottle of water. not work – No water flow

Mineral deposits clogging tanks. •See Care and Cleaning.

Cold water button Chiller door has been left open. •Close chiller door. does not dispense

Ice buildup blocking water flow. •Turn off cold power switch overnight and flip back on in

the morning.

Water dispenser leaks Crack or pin hole in bottle. • Replace with a new bottle of water. from the outside

Compressor does not start Normal Operation—Compressor • Wait for up to 3 minutes for the compressor to start. when cold power switch/ start is delayed by up to 3 minutes blue light is on to prolong the compressor life.

Bottle feels warm Water system overfilled. • Dispense cold water until air is released into the bottle.

Water is boiling in the hot tank and bubbling up into the bottle.

Particles floating in Water has high mineral content. •Find a water source with lower hardness. water

Foul odor in air around Hot water tank is empty or • Press the hot dispenser button until water flows to remove air dispenser not completely full. from the hot tank.

Care and cleaning of the dispenser.

For long vacations or absences, set both power switches (on the back of the dispenser) to the O (off) position.

1. Unplug the water dispenser.

2. Remove the water bottle.

3. Drain the water tanks (see Draining the

Dispenser).

4. Dry the separator thoroughly on both the

top and bottom (see Cleaning the Separator).

5. Leave the door of the chiller compartment open (on some models).

After returning from vacation, make sure to sanitize the water tanks before using the dispenser (see Cleaning and Sanitizing the Water Tank).

Preparing for Vacation

Chilling Rate: approx. 0.5 gallons (2 liters)

per hour

Heating Rate: approx. 0.8 gallons (3 liters)

per hour

Capacity: 3 or 5 gallon bottle

Power Consumption: Heating: 480 watts max.

Cooling: 125 watts max.

Specifications

Troubleshooting Tips.

Problem Possible Causes What To Do

Water dispenser is noisy Water dispenser is uneven. • Make sure the water is installed on a level floor or counter

strong enough to support it when fully loaded.

Bottle making a gurgling noise •This is normal. as water fills the tanks.

Hot water boiling sound. •This is normal.

Dispenser or water bottle shakes •This is normal. when the cooling system cycles off.

Chiller does not operate Chiller is not on. • Turn the Cold (Blue) power switch on. (chiller models only)

Water dispenser is unplugged. • Push the plug completely into the outlet.

The fuse is blown/circuit • Replace fuse or reset the breaker. breaker is tripped.

Vibration or rattling Water dispenser is on • Use shims to level the unit. (slight vibration an uneven surface. is normal)

Compressor/motor Often occurs when large •This is normal. operates (blue light on) amounts of food are placed for long periods or cycles in cooler. (chiller models only)

Door left open. • Check to see if package is holding door open.

Hot weather or frequent • This is normal. door openings.

Compressor/motor Normal when unit is first •Wait 24 hours for the unit to completely cool down. operates (blue light on) plugged in. for long periods or cycles

Not enough clearance • Make sure there is enough air circulation around

(all models)

from the wall. the unit.

Water system overfilled. •Dispense water from the cold faucet until air is released

into the bottle.

Chiller compartment Door left open. • Check to see if package is holding door open. too warm (chiller models only)

Compartment/cold water Low ambient temperature. • Place units in room temperature environment. too cold/frozen

Chiller compartment has Foods transmitting odor • Foods with strong odors should be tightly wrapped. odor (chiller models only) to chiller. • Keep an open box of baking soda in the unit; replace every

three months.

Interior needs cleaning. • See Care and cleaning.

Moisture forms on outside Not unusual during periods •Wipe surface dry. of chiller compartment of high humidity and/or • Operate unit in temperature- and humidity-controlled location. (chiller models only) temperature. • Place unit in tray to contain moisture accumulation.

Moisture collects inside Too frequent or too long •Minimize time door is open. chiller compartment door openings. • Wipe surface dry. (in humid weather, air • Empty internal drip tray. carries moisture into • Operate unit in temperature- and humidity-controlled location. chiller compartment • Place unit in tray to contain moisture accumulation. when door is opened) (chiller models only)

+ 19 hidden pages