GE GXCF03E, GXCF03KWW Owner’s Manual
ge.com
Cold and Room Temperature
Water Dispenser
215C1002P039 49-50223 02-07 JR
Safety Instructions . . . . . . . . . . . . .2, 3
Using the Water Dispenser
Assembling the Base . . . . . . . . . . . . . .4
Features and Parts List . . . . . . . . . . . .4
Loading the Dispenser . . . . . . . . . . . .4
Specifications . . . . . . . . . . . . . . . . . . . .6
Care and Cleaning . . . . . . . . . . . .5, 6
Troubleshooting Tips . . . . . . . . . . . .6
Consumer Support
Consumer Support . . . . . . .Back Cover
Warranty . . . . . . . . . . . . . . .Back Cover
Français
Informations en matière
de sécurité
. . . . . . . . . . . . . . . . . . .7, 8
Utilisation du distributeur d’eau
Caractéristiques et liste de pièces . . . .9
Caractéristiques techniques . . . . . . .11
Chargement du distributeur . . . . . . .9
Montage de la base . . . . . . . . . . . . . . .9
Entretien et nettoyage . . . . . . . .10, 11
Conseils de dépannage . . . . . . . . . .11
Soutien du consommateur
Garantie . . . . . . . . . . . . . . . . . . . . . .12
Soutien du consommateur . . . . . . . .12
Español
Información de seguridad
. . . .13, 14
Como utilizar el dispensador de agua
Cómo cargar el dispensador . . . . . . .15
Cómo ensemblar la base . . . . . . . . . .15
Especificaciones . . . . . . . . . . . . . . . . .17
Lista de partes y características . . . . .15
Cuidado y limpieza . . . . . . . . . .16, 17
Solucionar problemas . . . . . . . . . . .18
Servicio al consumidor
Garantía . . . . . . . . . . . . . . . . . . . . . . .19
Servicio al consumidor . . . . . . . . . . .19
GXCF03E
GXCF03KWW*
Owner’s Manual
La section française commence à la page 7
La sección en español empieza en la página 13
Distributeur d’eau froide
et à température ambiante
Dispensador de agua fría
y de temperatura ambiente
Manuel d’utilisation
Manual del propietario
As an ENERGY STAR®partner, GE
has determined that this product
meets the E
NERGY STAR
®
guidelines
for energy efficiency.
*ENERGY STAR®qualified product.
2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
PROPER INSTALLATION AND LOCATION
■
■ Allow at least 1″ (2.5 cm) of space between the
back of the water dispenser and the wall to allow
for proper air circulation.
■
■ Do not install the water dispenser where the
temperature will go below 50°F (10°C) or
above 100°F (38°C).
■
■ Install the water dispenser on a level floor or
counter strong enough to support it when fully
loaded. Do not install where it will be subject to
direct sunlight, heat or moisture.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
■
■ This water dispenser must be properly installed
and located in accordance with these instructions
before it is used.
■
■ Do not allow children to climb, stand or hang
on the outside of the dispenser, or on the shelves
inside the storage cabinet (on some models).
They could tip the dispenser over and damage
it and seriously injure themselves.
■
■ Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
■
■ Unplug the water dispenser before cleaning or
making repairs.
NOTE: GE does not support any servicing of the
dispenser. We strongly recommend that you do not
attempt to service the dispenser yourself.
■
■ Do not use this dispenser to dispense anything
other than water.
■
■ Do not plug in the power cord or turn on the
power switches when the water dispenser is empty.
■
■ Wipe up any water spills immediately after loading
or unloading water bottles.
■
■ WARNING: Do not use with water that is
microbiologically unsafe or of unknown quality.
■
■ CAUTION: Children should be supervised
by a parent when using this product.
3
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an
electrical short circuit, grounding reduces the risk of
electric shock.
This appliance is equipped with a power cord having
a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly
installed and grounded.
Consult a qualified electrician if the grounding
instructions are not completely understood, or if
doubt exists as to whether the appliance is properly
grounded.
If the outlet is a standard 2-prong wall outlet, it is
your personal responsibility and obligation to have
it replaced with a properly grounded 3-prong
wall outlet.
Do not under any circumstances cut or remove the
third (ground) prong from the power cord.
Do not use an adapter plug with this appliance.
Do not use an extension cord with this appliance.
If the power cord is too short, have a qualified
electrician install an outlet near the appliance.
For best operation, plug the appliance into its own
electrical outlet on a dedicated circuit to prevent
flickering of lights, blowing of fuse or tripping of
circuit breaker.
WARNING–Improper use of the grounding plug can result in a risk of electric shock.
PROPER DISPOSAL OF THE WATER DISPENSER
Refrigerant Disposal
Your old water dispenser may have used a regulated
refrigerant in its cooling system. These refrigerants
are believed to harm stratospheric ozone. If you are
throwing away your old dispenser, make sure the
refrigerant is removed and recovered for proper
disposal by an EPA-certified technician. If you
intentionally release this refrigerant, you can be
subject to fines and imprisonment under provisions
of environmental legislation.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
Sanitize the dispenser water tank prior to
installing a full bottle of water for the first time
(see “Cleaning and Sanitizing the Water Tank”).
IMPORTANT: Make sure the dispenser is
unplugged. Before placing the water bottle on
the dispenser, wash hands and wipe the top of
the bottle with a clean cloth. Avoid touching the
part of the bottle that will be in contact with the
water dispenser.
Make sure the water level in the top of the
dispenser is low enough to allow for proper
bottle installation. Failure to do so may cause
the dispenser to overflow.
1. Peel the label from the top cover of the
bottle (if present). Do not remove the
entire bottle cap.
2. Place the bottle on top of the dispenser
as shown, aligning the dispensing valve
probe to the center of the water bottle
cap. Press down until the probe
penetrates the bottle cap, allowing the
bottle to rest on the support collar.
3. IMPORTANT: Press both dispense levers
until water runs from both taps.
4. Plug in the dispenser.
5. Allow 30 minutes for water to reach cold
temperatures.
Contact a local water bottle distributor to
purchase water bottles.
Loading the Dispenser
4
Using the water dispenser.
Bottle Support Collar (WS28X10046)
Separator (WS28X10020)
Cold Water Tank
Cold (Blue) Faucet
Room Temperature (White) Faucet
Dispenser Drip Tray (WS28X10021) and
Grille (WS28X10022)
Base
(Top Cover – WS30X10006)
(Back Side – WS30X10007)
(Bottom Cover – WS30X10008)
(Front Side – WS30X10009)
See the back page of this manual
for ordering instructions.
Features and Parts List
1. Align the front and back pieces of the
base (pieces labeled 1 and 2), with “UP”
pointing up, and snap together. If it does
not go together, make sure “UP” is in the
same direction on both pieces.
2. Place the top cover (piece 3) on top of
pieces 1 and 2 (front and back). Press
down firmly until it snaps into place.
3. Turn the assembly over and place the
bottom cover (piece 4) on top of pieces
1 and 2 (front and back). Press down
firmly until it snaps into place.
4. Turn base over and place the dispenser
on top of the base.
Assembling the Base
UP
UP
NOTE: The top (3) and bottom (4)
pieces can be found in the top and
bottom of the carton packaging foam.
Care and cleaning of the dispenser.
The dispenser drip tray is not selfdraining. To reduce water spotting or
deposits, the tray and its grille should
be emptied, cleaned and wiped dry
regularly.
Clean with mild soap or on the top rack
in the dishwasher.
Cleaning the Drip Tray and Grille
Drip
tray
Drip
tray
grille
5
1. Before cleaning, unplug the water dispenser.
NOTE: For first time installation, skip
steps 2 and 3.
2. Empty the water bottle, then remove it from the
dispenser.
3. Drain the water tank (see Draining the Dispenser).
4. DO NOT ADD BLEACH FIRST OR DIRECTLY TO THE
DISPENSER. Concentrated bleach may damage plastic.
Add 1/2 teaspoon (2.5 ml) of ordinary 6.0%
maximum household bleach to a 2 quart (2 liter)
pitcher filled with tap water.
5. Pour the solution in the opening at the top of
the dispenser.
6. Repeat steps 4 and 5 until the dispenser is full.
7. Press the room temperature and cold dispenser
faucets until the water just begins to flow from
the taps.
8. Allow to sit for 15-20 minutes.
9. Rinse out the bleach solution:
— Drain the water tank by dispensing water through
the room temperature and cold dispenser faucets
(see Draining the Dispenser).
— IMPORTANT: Remove the separator and wipe out the
cold water reservoir (see Cleaning the Separator).
— Clean, then reinstall the separator and collar
(see Cleaning the Separator).
— Pour approximately 1 gallon (4 quarts or 4
liters) of fresh tap water into the top and drain
through the faucets.
— Flush with an additional 1 gallon (4 quarts or
4 liters) of fresh tap water and drain.
10. Install a fresh water bottle (see Loading the Dispenser).
11. Dispense 1 quart (1 liter) of water from each tap
and taste to make sure the bleach solution is
completely removed.
If you continue to taste the chlorine from the bleach solution,
repeat steps 9–11 until the taste is gone.
12. Plug in the dispenser.
Sanitizing and Cleaning the Water Tank
IMPORTANT: Unplug the water dispenser
before cleaning.
1. Remove the water bottle and drain the
dispenser (see Draining the Dispenser).
2.
Remove the support collar by turning
counterclockwise and pulling straight off.
3. Remove the plastic separator by
pulling straight out (you may need to
twist slightly to loosen).
4. Clean the separator with dish soap
and water or in the top rack of
the dishwasher.
5. Dry the separator thoroughly on
both sides.
6. Using a clean cloth or paper towel,
thoroughly dry the cold water
reservoir.
7. Place the separator back in the
dispenser. Make sure the long, tapered
end of the separator is positioned
firmly on the metal pipe on the
bottom of the reservoir.
8. Replace the support collar and turn
clockwise until it is firmly in place.
9. Install a full water bottle on the
dispenser (see Loading the Dispenser).
Cleaning the Separator
Separator
Support collar
To remove
To replace
IMPORTANT: Periodically the water dispenser tank must be sanitized to prevent unpleasant tastes in the water and cleaned to
remove mineral deposits that can impair flow.
To Remove Mineral Deposits:
Mix 2 quarts (2 liters) of water with two quarts of vinegar OR mix 1 gallon of water (4 liters) with 16 ounces (454 g) of citric acid
crystals. Bleach does not remove mineral deposits. Do this in place of step 4 when removing mineral deposits.
To Sanitize:
For long vacations or absences.
1.
Unplug the water dispenser.
2.Remove the water bottle.
3.Drain the water tank (see Draining the Dispenser).
4. Dry the separator thoroughly on both the top and bottom
(see Cleaning the Separator).
After returning from vacation, make sure to sanitize the water
tank before using the dispenser (see Cleaning and Sanitizing
the Water Tank).
Preparing for Vacation
Chilling Rate: approx. 0.5 gallons (2 L) per hour
Capacity: 3 or 5 gallon bottle
Power Consumption: 114W max.
Specifications
Problem Possible Causes What To Do
Water has poor taste Separator needs cleaning. •See Cleaning the Separator.
or odor
Unit needs to be sanitized. •See Cleaning and Sanitizing the Water Tank.
Water not cold enough Dispenser is unplugged. • Push the plug completely into the outlet.
The fuse is blown/circuit • Replace house fuse or reset the house circuit breaker.
breaker is tripped. • If too many items are plugged into a single circuit, move
some items to a different circuit.
All the water in the water tank •Wait 30 minutes for water to cool.
has been used.
Temperature limiter tripped. •Unplug the unit. Wait five minutes; then plug the unit
back in. Wait 30 minutes for water to cool.
Water dispenser does Empty water bottle. •Replace with a new bottle of water.
not work
Mineral deposits clogging tank. •See Care and Cleaning.
Water dispenser leaks Crack or pin hole in bottle. • Replace with a new bottle of water.
from the outside
Water dispenser is noisy Water dispenser is uneven. • Make sure the water is installed on a level floor or counter
strong enough to support it when fully loaded.
Bottle making a gurgling noise •This is normal.
as water fills the tanks.
Dispenser or water bottle shakes •This is normal.
when the cooling system cycles off.
Particles floating in water Water has high mineral content. •Find a water source with lower hardness.
Mineral deposits in water system. •Follow cleaning instructions for mineral deposits.
Troubleshooting Tips.
6
Care and cleaning of the dispenser.
IMPORTANT: Unplug the water dispenser before cleaning.
The inside and outside of the cabinet can be washed with
mild soap and water. Rinse thoroughly with clear water.
Never use commercial cleaners or abrasive scouring
powders.
Sweep away or vacuum any dust from the condenser coils
on the back of the unit. For best results, use a brush
specially designed for this purpose. It is available at most
appliance stores.
Cleaning the Outside and Storage Cabinet (on some models)
The dispenser should be drained before cleaning the tank and
before leaving for long vacations or absences.
Drain water through the faucets into a container.
Draining the Dispenser
Loading...