Page 1
GEAppliances.com
Safety Instructions
. . . . . . . . . . . .2–3
Owner’s Manual and
Installation Instructions
Top-Freezer
Operating Instructions
Automatic Icemaker . . . . . . . . . . . . . . . . . 8
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Crispers and Pans . . . . . . . . . . . . . . . . .6, 7
Shelves and Bins . . . . . . . . . . . . . . . . . . . .5
Care and Cleaning
Care and Cleaning . . . . . . . . . . . . . . 9, 10
Replacing the Light Bulb . . . . . . . . . . . .10
Installation Instructions
Preparing to Install
the Refrigerator . . . . . . . . . . . . . . . . . . . .11
Reversing the Door Swing . . . . . . 17-21
Water Line Installation . . . . . . . . . 12–15
Icemaker Installation . . . . . . . . . . . . . . .16
Troubleshooting Tips
Normal Operating Sounds . . . . . . . . . .22
Consumer Support
Consumer Support . . . . . . . . Back Cover
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .26
. . . . . . 23–25
Models GTE21 and GIE21
Congélateur supérieur
Réfrigérateurs
Manuel d’utilisation
et d’installation
La section française commence à la page 27
Congelador superior
Refrigeradores
Manual del propietario
e instalación
La sección en español empieza en la página 57
Write the model and serial numbers
here:
Note to Installer –
these instructions with the Consumer.
Note to Consumer –
instructions for future reference.
Note à l’installateur –
de laisser ces instructions au
consommateur.
Note au consommateur –
Conservez ces instructions pour
référence future.
Nota al instalador –
de dejar estas instrucciones con el
consumidor.
Nota al consumidor –
Refrigerators
estas instrucciones para referencia futura.
Be sure to leave
Keep these
Assurez-vous
Asegúrese
Conserve
Model # _________________________
Serial #
Find these numbers on the gray label
on the left side, near the top of the
refrigerator compartment.
__________________________
245D1676P001
49-60726 07-14 GE
Page 2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
SAFETY
IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING
GE Appliances website
For more information on your refrigerator’s operation, visit
call 800.GECARES (800.432.2737). In Canada visit
GEAppliances.ca
REFRIGERATOR SAFETY INFORMATION
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All
safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are
defined as:
www
.
GEAppliances.com
or call 800.561.3344.
or
DANGER
WARNING
CAUTION
Indicates a hazardous situation which, if not avoided,
Indicates a hazardous situation which, if not avoided,
Indicates a hazardous situation which, if not avoided,
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of fire, explosion, electric shock, or injury when using your
refrigerator follow these basic safety precautions:
This refrigerator must be properly installed and located in
accordance with the Installation Instructions before it is
used.
Unplug the refrigerator before cleaning and making repairs.
NOTE: Repairs must be performed by a qualified Service
Professional.
Replace all parts and panels before operating.
Because of potential safety hazards under certain
conditions, we strongly recommend against the use of an
extension cord. However, if you must use an extension cord,
it is absolutely necessary that it be a UL-listed (in the United
States) or a CSA certified (in Canada), 3-wire grounding type
appliance extension cord having a grounding type plug
and outlet and that the electrical rating of the cord be 15
amperes (minimum) and 120 volts.
To prevent suffocation and entrapment hazards to children,
Remove the fresh food and freezer doors from any
refrigerator before disposing of it or discontinuing its use.
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Power to the refrigerator cannot be disconnected by
any setting on the control panel, refrigerator must be
unplugged to remove power.
Do not allow children to climb, stand or hang on the door
handles or the shelves in the refrigerator. They could
seriously injure themselves.
will
result in death or serious injury.
could
result in death or serious injury.
could
result in minor or moderate injury.
In refrigerators with automatic ice makers, avoid contact
with the moving parts of the ejector mechanism, or with
the heating element that releases the cubes. Do not place
fingers or hands on the automatic ice making mechanism
while the refrigerator is plugged in.
Do not clean glass shelves or covers with warm water
when they are cold. Glass shelves and covers may break if
exposed to sudden temperature changes or impact, such
as bumping or dropping. Tempered glass is designed to
shatter into many small pieces if it breaks.
Keep fingers out of the “pinch point” areas; clearances
between the doors and between the doors and cabinet are
necessarily small. Be careful closing doors when children
are in the area.
Do not touch the cold surfaces in the freezer compartment
when hands are damp or wet., skin may stick to these
extremely cold surfaces.
Do not refreeze frozen foods which have thawed
completely.
Before replacing a burned-out light bulb, the refrigerator
should be unplugged in order to avoid contact with a live
wire filament. (A burned-out light bulb may break when
being replaced.)
WARNING
Explosion Hazard.
Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so
can result in fire, explosion, or death.
2
Page 3
SAFETY (CONT.)
CONNECTING ELECTRICITY
GEAppliances.com
WARNING
Electrical Shock Hazard.
Plug into a grounded 3-prong outlet
Do not remove the ground prong
Do not use an adapter
Failure to follow these instructions can result in death, fire, or electrical shock.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with a 3-prong
(grounding) plug which mates with a standard 3-prong
(grounding) wall outlet to minimize the possibility of electric
shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is
your personal responsibility and obligation to have it replaced
with a properly grounded 3-prong wall outlet. Do not use an
adapter.
The refrigerator should always be plugged into its own
individual electrical outlet which has a voltage rating that
matches the rating plate.
and also prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the power cord.
Always grip plug firmly and pull straight out from the outlet.
Repair or replace immediately all power cords that have
become frayed or otherwise damaged. Do not use a cord
that shows cracks or abrasion damage along its length or at
either end.
When moving the refrigerator away from the wall, be careful
not to roll over or damage the power cord.
This provides the best performance
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an
extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or
a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet
and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
PROPER DISPOSAL OF YOUR OLD REFRIGERATOR
WARNING
Remove fresh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can
result in child entrapment which can lead to death or brain damage.
IMPORTANT:
Suffocation and child entrapment hazard.
Child entrapment and suffocation are not problems of the past.
Junked or abandoned refrigerators are still dangerous even if
they will sit for “just a few days.” If you are getting rid of your old
refrigerator, please follow the instructions below to help prevent
accidents.
Before You Throw Away Your Old Refrigerator or
Freezer:
Take off the fresh food and freezer doors.
Leave the shelves in place so that children may not easily
climb inside.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
Refrigerants
All refrigeration products contain refrigerants, which under
federal law must be removed prior to product disposal. If you
are getting rid of an old refrigeration product, check with the
company handling the disposal about what to do.
3
Page 4
About the controls on the refrigerator.
The controls on your refrigerator will look like the following:
Control Settings
Initially, set the refrigerator control to the recommended setting. Allow 24 hours for the
temperature to stabilize.
Several adjustments may be required. Adjust the refrigerator control one increment at a time
and allow 12 hours after each adjustment for the refrigerator to reach the temperature you
have set.
Setting the refrigerator control to
compartments but does not shut off electrical power to the refrigerator.
Control settings will vary based on personal preferences, usage and operating
conditions, and may require more than one adjustment. Factors that affect
temperature include the amount of food in the refrigerator or freezer, the frequency of
door opening and the temperature of food when it is placed in the refrigerator.
Off
stops cooling in both the freezer and refrigerator
4
Page 5
About the shelves and bins. GEAppliances.com
Not all features are on all models.
Rearranging the Shelves
Shelves in the refrigerator and freezer compartments are adjustable.
Refrigerator Compartment
Track
Lift up
Slide
forward
Full-Width Shelves
The shelf rests on a molded side-wall
support and locks into a track on the rear
cabinet wall on each side.
To remove:
Lift the shelf up through the space in the
track.
Slide the shelf forward along the track.
Pull the shelf out of the unit.
To replace:
Reverse removal steps above.
Freezer Compartment
To remove:
CAUTION
shelves or covers with warm water
when they are cold. Glass shelves and
covers may break if exposed to sudden
temperature changes or impact such as
bumping or dropping. Tempered glass
is designed to shatter into many small
pieces if it breaks.
Do not wash any plastic refrigerator parts in the
dishwasher.
Do not clean glass
Lift up both sides of the shelf and slide it
left into the center of the shelf supports.
Rotate the right side of the shelf up and
out of the shelf supports.
To replace:
Holding the shelf diagonally, insert the
left end of the shelf into the top of the
shelf supports on the side wall.
Insert the right end of the shelf into the
shelf supports on the side wall. Rest
each end of the shelf on the bottom of
the shelf supports.
5
Page 6
About the crispers and pans.
Not all features are on all models.
Fruit and Vegetable Crispers
Excess water that may accumulate in the
bottom of the drawers or under the drawers
should be wiped dry.
Adjustable Humidity Crisper
Slide the control all the way to the
setting to provide high humidity recommended
for most vegetables.
Vegetables
Snack Pan
This pan can be moved to the most useful
location for your family’s needs.
Slide the control all the way to the
to provide lower humidity levels recommended
for most fruits.
To remove,
position, lift the pan up and past the
position, and lift out.
slide the pan out to the
Fruits
stop
stop
setting
6
Page 7
About crisper removal. GEAppliances.com
Not all features are on all models.
Crisper Removal
Unload the bottom shelf before attempting to
remove the storage drawers.
To Remove:
Lift the drawers up slightly while pulling them
stop
past the
If the door prevents you from taking out the
drawers, first try to remove the door bins.
If this does not offer enough clearance, the
refrigerator will need to be rolled forward
until the door opens enough to slide the
drawers out. In some cases, when you roll the
refrigerator out, you will need to move the
refrigerator to the left or right as you roll it out.
To remove the glass cover:
Remove the glass, then the frame. When
replacing the glass, push the front edge firmly
into the frame.
location.
Removing the glass cover
Removing the frame
Push up the glass cover at the rear.
Slide the glass cover backwards until the
front edge comes out of the frame.
Rotate the side of the glass cover up.
Remove the glass cover.
To remove the frame:
Lift up the front of the frame using both
hands.
Slide the frame forward.
Rotate the side of the frame up.
Remove the frame.
7
Page 8
About the automatic icemaker.
A newly-installed refrigerator may take 12–24 hours to begin making ice.
Power Switch
Icemaker
Feeler Arm
Automatic Icemaker (on some models)
CAUTION
moving parts of the ejector mechanism, or with
the heating element (located on the bottom of
the ice maker) that releases the cubes. Do not
place fingers or hands on the automatic ice
making mechanism while the refrigerator is
plugged in.
The icemaker will produce approximately 3 to
1
ø
2 lbs. of ice in a 24-hour period, depending on
3
the freezer compartment temperature, room
temperature, number of door openings and
other use conditions.
If the refrigerator is operated before the water
connection is made to the icemaker, move the
power switch to
When the refrigerator has been connected to
the water supply, set power switch to
The icemaker will fill with water when it cools to
15°F. A newly-installed refrigerator may take 12
to 24 hours to begin making ice cubes.
Once the icemaker starts to make ice, it may
take up to 48 hours to fill the bin, depending on
the temperature settings and number of door
openings.
Avoid contact with the
OFF
.
ON
You will hear a buzzing sound each time the
icemaker fills with water.
Throw away the first few batches of ice to allow
the water line to clear.
Be sure nothing interferes with the sweep of the
feeler arm.
When the bin fills to the level of the feeler arm,
the icemaker will stop producing ice.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes will
become cloudy, taste stale, shrink or fuse
together.
NOTE: In homes with lower-than-average water
pressure, you may hear the icemaker cycle
multiple times when making one batch of ice.
Icemaker Accessory Kit
If your refrigerator did not already come
equipped with an automatic icemaker, an
icemaker accessory kit is available at extra cost.
Check the back of the refrigerator for the specific
ice maker kit needed for your mode
l.
8
Page 9
Care and cleaning of the refrigerator. GEAppliances.com
Cleaning the Outside
The door handles and trim.
dampened with soapy water. Dry with a soft cloth.
Keep the outside clean.
lightly dampened with kitchen appliance wax or
mild liquid dish detergent. Dry and polish with a
clean, soft cloth.
The stainless steel panels and door handles
(on some models) can be cleaned with a
commercially available stainless steel cleaner.
Cleaners with oxalic acid such as Bar Keepers
Clean with a cloth
Wipe with a clean cloth
Cleaning the Inside
Friend Soft Cleanser will remove rust, tarnish,
and small blemishes Use only a liquid cleanser
free of grit and rub in the direction of the brush
lines with a damp soft sponge. Do not use
appliance wax or polish on the stainless steel.
Do not wipe the refrigerator with a soiled dish
cloth or wet towel. These may leave a residue
that can erode the paint. Do not use scouring
pads, powdered cleaners, bleach or cleaners
containing bleach because these products can
scratch and weaken the paint finish.
To help prevent odors,
of baking soda in the fresh food and freezer
compartments.
Unplug the refrigerator before cleaning.
this is not practical, wring excess moisture
out of sponge or cloth when cleaning around
switches, lights or controls.
8VHZDUPZDWHUDQGEDNLQJVRGDVROXWLRQ³
about a tablespoon (15 ml) of baking soda to
a quart (1 liter) of water. This both cleans and
neutralizes odors. Thoroughly rinse and wipe dry.
Avoid cleaning cold glass shelves (on some
models) with hot water because the extreme
temperature difference may cause them to
break. Handle glass shelves carefully. Bumping
tempered glass can cause it to shatter.
leave an open box
If
Condenser
There is no need for routine condenser
cleanings in normal home operating
environments. However, in environments
that may be particularly dusty or greasy, the
condenser should be cleaned periodically for
efficient refrigerator operation.
Do not wash any plastic refrigerator parts in
the dishwasher.
Do not clean with any products containing
detergent, bleach or ammonia. They may
damage the refrigerator.
After cleaning the door gaskets, apply a
thin layer of petroleum jelly to the door
gaskets at the hinge side. This helps keep
the gaskets from sticking and bending out
of shape.
Cleaning the condenser:
Sweep away or vacuum up dust.
Moving the Refrigerator
Be careful when moving the refrigerator away
from the wall. All types of floor coverings can
be damaged, particularly cushioned coverings
and those with embossed surfaces.
Turn the leveling legs at each front corner
of the refrigerator counterclockwise until
the rollers support the refrigerator. Pull the
refrigerator straight out and return it to position
by pushing it straight in.
Moving the refrigerator in a side direction
may result in damage to the floor covering or
refrigerator.
When pushing the refrigerator back, make sure
you don’t roll over the power cord or icemaker
supply line (on some models).
After rolling the refrigerator back into place,
turn the legs clockwise until the legs again bear
the weight of the refrigerator
9
Page 10
Care and cleaning of the refrigerator.
Preparing for Vacation
For long vacations or absences, remove
food and unplug the refrigerator. Move the
refrigerator control to the
clean the interior with a baking soda solution of
one tablespoon (15 ml) of baking soda to one
quart (1 liter) of water. Leave the doors open.
Preparing to Move
Secure all loose items such as grille, shelves
and drawers by taping them securely in place
to prevent damage. To prevent the doors from
opening while moving, secure them to the case
with tape.
Replacing the light bulb.
Setting the refrigerator control to
OFF
does not remove power to the light circuit.
OFF
position and
Set the icemaker power switch to the
position and shut off the water supply to the
refrigerator.
If the temperature can drop below freezing,
have a qualified servicer drain the water supply
system (on some models) to prevent serious
property damage due to flooding.
Be sure the refrigerator stays in an upright
position during moving.
OFF
5HIULJHUDWRU&RPSDUWPHQW³8SSHU/LJKW
CAUTION
Unplug the refrigerator.
The bulb is located at the top of the
compartment near the opening.
Light bulb may be hot.
Replace with an appliance bulb of the
same or lower wattage.
Plug the refrigerator back in.
10
Page 11
Installation
Refrigerator
Instructions
If you have questions, call 1.800.GE.CARES
In Canada, call 1.800.561.3344
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT –
local inspector’s use.
•
IMPORTANT –
codes and ordinances.
• Note to Installer –
instructions with the Consumer.
• Note to Consumer –
for future reference.
• Skill level
basic mechanical skills.
• Completion time
•
Proper installation is the responsibility of the installer.
•
Product failure due to improper installation is not
covered under the Warranty.
– Installation of this appliance requires
– Refrigerator Installation
15 minutes.
Save these instructions for
Observe all governing
Be sure to leave these
Keep these instructions
or
Visit our Website at:
Models GTE21 and GIE21
or visit our Website at:
www.geappliances.ca
CLEARANCES
Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections.
•
Sides 1/8s(3.5mm)
•
Top 1/8s(3.5mm)
•
Back 1s(25mm)
If the refrigerator is to be installed next to a wall on the
hinge side, allow 5/16s (8 mm) door clearance.
ROLLERS AND LEVELING LEGS
Leveling legs
are adjustable. They firmly position the refrigerator and
prevent it from moving when the doors are opened.
Leveling legs should be set so the front of the refrigerator
is raised just enough that the doors close easily when
opened about halfway.
near each front corner of the refrigerator
GEAppliances.com
WATER SUPPLY TO THE ICEMAKER
(ON SOME MODELS)
If the refrigerator has an icemaker, it will have to be
connected to a cold water line. A GE water supply kit
(containing tubing, shutoff valve, fittings and instructions)
is available at extra cost from your dealer or by visiting
our Website at
www.geappliances.ca
1.877.959.8688.
GEAppliances.com
) or from Parts and Accessories,
(in Canada at
REFRIGERATOR LOCATION
• Do not install the refrigerator where the temperature
will go below 55°F (12.7°C) because it will not run often
enough to maintain proper temperatures.
• Install it on a floor strong enough to support it fully
loaded.
Turn the leveling legs
counterclockwise to lower it
Rollers
next to the leveling legs allow you to move the
refrigerator away from the wall for cleaning.
Turn the legs counterclockwise until the weight of the
refrigerator is transferred from them to the rollers. After
rolling the refrigerator back into place, turn the legs
clockwise until the legs again bear the weight of the
refrigerator.
clockwise to raise
.
Clockwise to raise
refrigerator
the refrigerator,
11
Page 12
Installation Instructions
INSTALLING THE WATER LINE
BEFORE YOU BEGIN
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of tubing
you need. Approved plastic water supply lines are GE
SmartConnect
WX08X10006, WX08X10015 and WX08X10025).
When connecting your refrigerator to a GE Reverse
Osmosis Water System, the only approved installation
is with a GE RVKit. For other reverse osmosis water
systems, follow the manufacturer’s recommendations.
If the water supply to the refrigerator is from a Reverse
Osmosis Water Filtration System AND the refrigerator
also has a water filter, use the refrigerator’s filter
bypass plug. Using the refrigerator’s water filtration
cartridge in conjunction with the RO filter can result
in hollow ice cubes and slower water flow from the
water dispenser.
This water line installation is not warranted by
the refrigerator or icemaker manufacturer. Follow
these instructions carefully to minimize the risk of
expensive water damage.
Water hammer (water banging in the pipes) in
house plumbing can cause damage to refrigerator
parts and lead to water leakage or flooding. Call a
qualified plumber to correct water hammer before
installing the water supply line to the refrigerator.
To prevent burns and product damage, do not hook
up the water line to the hot water line.
If you use your refrigerator before connecting the
water line, make sure the feeler arm is in the
position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a power
drill) during installation, be sure the device is double
insulated or grounded in a manner to prevent the
hazard of electric shock, or is battery powered.
™
Refrigerator Tubing (WX08X10002,
OFF
WHAT YOU WILL NEED
•
Copper or GE SmartConnect™ Refrigerator Tubing
kit
, 1/4" outer diameter to connect the refrigerator to
the water supply. If using copper, be sure both ends
of the tubing are cut square.
To determine how much tubing you need: measure
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Then add 8 feet (2.4
m). Be sure there is sufficient extra tubing (about 8 feet
[2.4 m] coiled into 3 turns of about 10" [25 cm] diameter)
to allow the refrigerator to move out from the wall after
installation.
GE SmartConnect™ Refrigerator Tubing Kits are
available in the following lengths:
2'(.6 m) – WX08X10002
8'(2.4 m) – WX08X10006
15'(4.6m) – WX08X10015
25' (7.6 m) – WX08X10025
Be sure that the kit you select allows at least 8 feet
(2.4 m) as described above.
NOTE: The only GE approved plastic tubing is that
supplied in GE SmartConnect™ Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times.
Certain types of plastic will crack or rupture with age
and cause water damage to your home.
•
A GE water supply kit
valve and fittings listed below) is available at extra
cost from your dealer or from Parts and Accessories,
800.626.2002.
•
A cold water supply
between 20 and 120 p.s.i. (1.4–8.2 bar) on models
without a water filter and between 40 and 120 p.s.i.
(2.8–8.2 bar) on models with a water filter.
(containing tubing, shutoff
. The water pressure must be
All installations must be in accordance with local
plumbing code requirements.
WARNING
supply only.
Connect to potable water
12
•
Power drill.
•
1/2" or adjustable wrench.
•
Straight and Phillips blade screwdriver.
Page 13
Installation Instructions
INSTALLING THE WATER LINE (cont.)
WHAT YOU WILL NEED (CONT.)
•
Two 1/4” outer diameter compression nuts and 2
ferrules (sleeves)
the shutoff valve and the refrigerator water valve.
OR
• If you are using a GE SmartConnect™ Refrigerator
Tubing kit, the necessary fittings are preassembled
to the tubing.
• If your existing copper water line has a flared fitting
at the end, you will need an
plumbing supply stores) to connect the water
line to the refrigerator OR you can cut off the
flared fitting with a
compression fitting. Do not cut formed end from
GE SmartConnect
³WRFRQQHFWWKHFRSSHUWXELQJWR
adapter
tube cutter
™
Refrigerator tubing.
(available at
and then use a
2
CHOOSE THE VALVE LOCATION
Choose a location for the valve that is easily
accessible. It is best to connect into the side of a
vertical water pipe. When it is necessary to connect
into a horizontal water pipe, make the connection
to the top or side, rather than at the bottom, to
avoid drawing off any sediment from the water
pipe.
3
DRILL THE HOLE FOR THE VALVE
Drill a 1/4" hole in the water pipe (even if using
a self-piercing valve) using a sharp bit. Remove
any burrs resulting from drilling the hole in the
pipe.
Take care not to allow water to drain into
the drill.
reduced ice production or smaller cubes.
Failure to drill a 1/4" hole may result in
•
Shutoff valve
to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32” at the point of
connection to the
COLD WATER LINE
. Saddle-type
shutoff valves are included in many water supply
kits. Before purchasing, make sure a saddle-type
valve complies with your local plumbing codes.
Install the shutoff valve on the nearest frequently used
drinking water line.
1
SHUT OFF THE MAIN WATER SUPPLY
Turn on the nearest faucet long enough to clear
the line of water.
4
FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water pipe with
the pipe clamp.
Pipe Clamp
Saddle-Type
Shutoff Valve
NOTE:
Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
Vertical Cold
Water Pipe
13
Page 14
Installation Instructions
INSTALLING THE WATER LINE (cont.)
5
TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing washer
begins to swell.
NOTE:
Do not overtighten or you may crush the
tubing.
Washer
Pipe Clamp
Clamp
Screw
6
ROUTE THE TUBING
Route the tubing between the cold water line and the
refrigerator.
Route the tubing through a hole drilled in the wall
or floor (behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
NOTE:
Be sure there is sufficient extra tubing [about 8
feet (244 cm) coiled into 3 turns of about 10" (25 cm)
diameter] to allow the refrigerator to move out from
the wall after installation.
7
CONNECT THE TUBING TO
THE VALVE
Place the compression nut and ferrule (sleeve)
for copper tubing onto the end of the tubing and
connect it to the shutoff valve.
Make sure the tubing is fully inserted into the valve.
Tighten the compression nut securely.
For plastic tubing from a GE SmartConnect
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then tighten
one additional turn with a wrench. Overtightening
may cause leaks.
Saddle-Type
Shutoff Valve
Inlet End
™
Compression
Nut
SmartConnect™
Tubing
NOTE:
Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
8
FLUSH OUT THE TUBING
Turn the main water supply on and flush out the
tubing until the water is clear.
Shut the water off at the water valve after about
one quart (1 liter) of water has been flushed
through the tubing.
9
CONNECT THE TUBING TO THE
REFRIGERATOR
NOTES:
• Before making the connection to the refrigerator,
be sure the refrigerator power cord is not plugged
into the wall outlet.
• If your refrigerator does not have a water filter
we recommend installing one. If your water
supply has sand or particles that could clog the
screen of the refrigerator’s water valve. Install it
in the water line near the refrigerator. If using GE
SmartConnect™ Refrigerator Tubing kit, you will
need an additional tube (WX08X10002) to connect
the filter. Do not cut plastic tube to install filter.
Remove the access
cover.
Remove the plastic flexible
cap from the water valve
(refrigerator connection).
Packing Nut
Outlet Valve
Ferrule (sleeve)
14
Page 15
Installation Instructions
INSTALLING THE WATER LINE (cont.)
9
CONNECT THE TUBING
TO THE REFRIGERATOR (CONT.)
Place the compression nut and ferrule (sleeve)
onto the end of the tubing as shown. On GE
SmartConnect™ Refrigerator Tubing kit, the nuts are
already assembled to the tubing.
Insert the end of the tubing into the water valve
connection as far as possible. While holding the
tubing, tighten the fitting.
For plastic tubing from a GE SmartConnect
Refrigerator Tubing kit, insert the molded end of the
tubing into the refrigerator connection and tighten
compression nut until it is hand tight, then tighten
one additional turn with a wrench. Overtightening
may cause leaks.
Fasten the tubing into the clamp provided to hold it
in a vertical position. You may need to pry open the
clamp.
Tubing
Clamp
1/4" Tubing
TURN THE WATER ON AT THE
10
SHUTOFF VALVE (CONT.)
Reattach the compressor
compartment access
cover.
11
INSTALLING THE REFRIGERATOR
Plug in the refrigerator.
Arrange the coil of tubing so
that it does not vibrate against
the back of the refrigerator
or against the wall. Push the
refrigerator back to the wall.
1/4"
Compression
Nut
Ferrule
(sleeve)
Refrigerator
Connection
TURN THE WATER ON AT THE
10
SHUTOFF VALVE
Tighten any connections that leak.
SmartConnect
Tubing
™
START THE ICEMAKER
12
Set the icemaker power switch to the ON position.
The icemaker will not begin to operate until it
reaches its operating temperature of 15°F (–9°C)
or below. It will then begin operation automatically
if the icemaker power switch is in the ON position.
15
Page 16
Installation Instructions
ICEMAKER INSTALLATION INSTRUCTIONS
BEFORE YOU BEGIN
Read each step thoroughly before proceeding.
2
REPOSITION FREEZER SHELF
Make sure the freezer shelf is in the lowest position.
WARNING
electric shock or injury during installation,
you must first unplug the refrigerator
before proceeding. Failure to follow these
instructions can result in electrical shock.
To eliminate the risk of
TOOLS YOU WILL NEED
Flat blade and Phillips
screwdrivers
1
PREPARE FOR INSTALLATION
• Remove and discard the large white plug from the
rear freezer wall.
• Remove the outlet cover with a flat-blade screwdriver.
Pliers
Sharp knife
PREPARE FOR INSTALLATION
3
There is a lebel on the back of the refrigerator that
will tell you which fill tube to use. Follow the icemaker
installation manual that comes with yuor icemaker kit
carefully to complet the icemaker installation.
Remove
plug
16
Page 17
Installation Instructions
REVERSING THE DOOR SWING
IMPORTANT NOTES
When reversing the door swing:
•
Read the instructions all the way through before
starting.
•
Handle parts carefully to avoid scratching paint.
•
Set screws down by their related parts to avoid using
them in the wrong places.
•
Provide a non-scratching work surface for the doors.
IMPORTANT:
until door-swing reversal is completed.
These instructions are for changing the hinges from the
ULJKWVLGHWRWKHOHIWVLGH³LI\RXHYHUZDQWWRFKDQJH
the hinges back to the right side, follow these same
instructions and reverse all references to left and right.
Unplug the refrigerator from its electrical outlet.
NOTE:
so could damage the door stop.
CAUTION
The Fresh Food and Freezer doors are heavy Use
both hands to secure the doors before lifting.
Once you begin, do not move the cabinet
Do not let either door drop to the floor. To do
Lifting Hazard
REMOVE FREEZER DOOR
1
1.
Remove all food from the inner door liner..
2.
Tape the door shut with masking tape.
3.
Remove the hinge cover on top of the freezer door
with a thin-blade screwdriver..
4.
Remove the three screws with a 5/16ssocket and
ratchet, then lift the hinge straight up to free the
hinge pin from the socket in the top of the door.
Top Hinge
TOOLS YOU WILL NEED
5/16s socket and ratchet
Phillips screwdriver
Masking tape
thin-blade screwdriver
Allen wrench (Stainless Steel
Handle Models)
Putty knife or
5.
Remove the tape and tilt the door away from the
cabinet. Lift it off the center hinge pin.
6
Remove the hole covers with a putty knife on the
opposite side of the three hinges.
Hole Cover
7.
Set the door on a non-scratching surface with the
inside up.
Center Hinge
Hole Covers
Bottom Hinge
Hole Covers
17
Page 18
Installation Instructions
REVERSING THE DOOR SWING (CONT.)
REMOVE REFRIGERATOR DOOR
2
1.
Remove all food from the inner door liner.
2.
Tape the door shut with masking tape.
3.
Remove the center hinge pin with a Phillips
screwdriver.
4.
Remove the center hinge by removing two hinge
screws with a 5/16s socket and ratchet. Save the
center hinge, hinge pin, screws and center hinge
gasket.
Center
Hinge Pin
3
TRANSFER BOTTOM HINGE TO THE
LEFT
1.
Using a 5/16 Socket
and ratchet, remove
the 2 screws from the
bottom hinge.
2.
Move the bottom
hinge pin from the
right to the left side
with a thin-blade
screwdriver until the
shoulder of the hinge
pin is touching the
hinge.
3.
Move the bottom
hinge from the right
to the left side and
tighten the 2 screws.
Center Hinge
Gasket
5.
Remove the tape and tilt the door away from the
cabinet. Lift the door straight up to free its bottom
socket from the pin in the bottom hinge bracket.
6.
Set the door on a non-scratching surface with the
inside up.
7.
Install the 2 hole plugs from the opposite side of
the cabinet to the screw holes vacated by the
center hinge removal.
4.
Install the 2 hole
plugs from the
opposite side of the
cabinet to the screw
holes vacated by
the bottom hinge
removal.
TRANSFER DOOR STOP TO THE LEFT
4
1.
On both the refrigerator and freezer doors,
remove the screws from the door stop on the
right with a Phillips screwdriver.
2.
Install the door stop on the left of each door.
18
Page 19
Installation Instructions
REVERSING DOOR HANDLES –
5
TRANSFER FREEZER DOOR HANDLE
TO THE RIGHT SIDE OF THE
REFRIGERATOR DOOR
1.
Remove the two
screws securing
the bottom end of
the handle with a
Phillips screwdriver
and remove the GE
bacge.
2. For Plastic handles:
Pull handle down
and off of the
fastener on the door.
REVERSING DOOR HANDLES –
5
TRANSFER FREEZER DOOR HANDLE
TO THE RIGHT SIDE OF THE
REFRIGERATOR DOOR (CONT.)
4.
Remove the plug button from the surface of the right
side of the refrigerator
door and insert the
fastener with
a Phillips screwdriver.
5. For Plasic handle:
handle to fresh food door on
fastener and slide downward
to lock in place with the
screws at the top of the
handle.
Attach
For Stainless Steel
handeles:
Loosen the set
screw on the
handle with 1/8”
wrench and
remove handle.
3.
Remove the fastener from the surface of the freezer
door, and cover the new vacant hole with the
GE Badge. (For a new unit, the GE Badge can be
found in your handle kit. If you need a new badge
call 800.GE.CARES (800.432.2737) (in Canada call
800.561.3344).
For Stainless Steel handle:
Attach handle to fresh food
door with screws at the top
of the handle. Use 1/8” allen
wrench to tighten the set
screw at the bottom of the
handle.
NOTE:
Do not over-tighten.
19
Page 20
Installation Instructions
REVERSING THE DOOR SWING (CONT.)
REVERSING DOOR HANDLES –
6
TRANSFER REFRIGERATOR DOOR
HANDLE TO THE RIGHT SIDE OF THE
FREEZER DOOR
1.
Remove the two screws
securing the top end of
the handle with a Phillips
screwdriver and remove the
GE badge.
2. For Plactic handle
up and off of the fastener on
the door
For Stainless
Steel handle:
Loosen set screw
on handle with
1/8” wrench and
remove handle.
3.
Remove the fastener from the surface of the
refrigerator door, and cover the new vacant hole
with the plug from the opposite side..
: Pull handle
REVERSING DOOR HANDLES –
6
TRANSFER REFRIGERATOR DOOR
HANDLE TO THE RIGHT SIDE OF THE
FREEZER DOOR (CONT.)
4.
Insert the fastener into the
surface of the right side
of the freezer door with a
Phillips screwdriver.
5. For Plactic handle
Attach handle to
the freezer door on
fastener and slide
upward to lock in
place with the screws
at the bottom of the
handle.
For Stainless
Steel Handle
Attach the
handle to the
freezer door
with screws at
the bottom of
the handles.
Use 1/8” allen
wrench to
tighten the
set screw at
the top of
thehandle.
:
:
20
NOTE:
Do not over-tighten.
Page 21
Installation Instructions
REHANG THE REFRIGERATOR DOOR
7
1.
Lower the refrigerator door onto the bottom
hinge pin.
2.
While holding the door securely, align the socket
in the door with the hole in the center hinge.
Attach the center hinge and gasket with two
screws with a 5/16s socket and ratchet.
3.
Check to ensure the alignment between the socket
in the door and the hole in the center hinge. Insert
the hinge pin into the center hinge and tighten with
a Phillips screwdriver until the shoulder of the hinge
pin is touching the center hinge.
REHANG THE FREEZER DOOR
8
1.
Lower the freezer door onto the center hinge pin.
2.
Place the left top hinge so the pin fits into the door
socket. (Left top hinge and cover can be found inside
of the product. Call GE Service at 800.GE.CARES
(800.432.2737 or in Canada call 800.561.3344 if
parts are missing.) Support the door on the handle
side and make sure the door is straight and the gap
between the doors is even across the front. While
holding the door in place, tighten the top hinge
screws. Do not overtighten these screws. Tighten
them until they are just snug, and then turn them
another one-half turn.
21
3.
Snap the left top hinge cover over the hinge.
Page 22
Normal operating sounds.
Newer refrigerators sound different from older refrigerators. Modern refrigerators
have more features and use newer technology.
Do you hear what I hear? These sounds are normal.
HUMMM...
WHOOSH...
■
The new high efficiency compressor may run faster
and longer than your old refrigerator and you may
hear a high-pitched hum or pulsating sound while
it is operating.
■
You may hear a whooshing sound when the doors close.
This is due to pressure equalizing within the refrigerator.
■
You may hear the fans spinning at high speeds.
This happens when the refrigerator is first plugged in,
when the doors are opened frequently or when
a large amount of food is added to the refrigerator
or freezer compartments. The fans are helping to
maintain the correct temperatures.
CLICKS, POPS,
CRACKS and CHIRPS
■
You may hear cracking or popping sounds when the
refrigerator is first plugged in. This happens as the
refrigerator cools to the correct temperature.
■
The compressor may cause a clicking or chirping
sound when attempting to restart (this could take
up to 5 minutes).
■
Expansion and contraction of cooling coils during and
after defrost can cause a cracking or popping sound.
■
On models with an icemaker, after an icemaking cycle,
you may hear the ice cubes dropping into
the ice bucket.
■
On models with a dispenser, during water dispense,
you may hear the water lines move at initial dispense
and after dispenser button is released.
WATER SOUNDS
■
The flow of refrigerant through the freezer cooling coils
may make a gurgling noise like boiling water.
■
Water dropping on the defrost heater can cause a
sizzling, popping or buzzing sound during the defrost
cycle.
■
A water dripping noise may occur during the defrost
cycle as ice melts from the evaporator and flows into
the drain pan.
■
Closing the door may cause a gurgling sound due to
pressure equalization.
22
Page 23
Before you call for service… GEAppliances.com
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Problem Possible Causes What To Do
Freezer door pops open
when refrigerator door
is closed
Door does not close
by itself
Refrigerator does
not operate
Vibration or rattling
(slight vibration is normal)
Motor operates for
long periods or cycles
on and off frequently
(Modern refrigerators
with more storage
space and a larger
freezer require more
operating time. They
start and stop of
to maintain even
temperatures.)
ten
This is normal if, after
popping open, the freezer
door closed on its own.
Leveling legs need adjusting.
Refrigerator in defrost cycle.
Refrigerator control in
1 (off)
position.
Refrigerator is unplugged.
The fuse is blown/circuit
breaker is tripped.
Refrigerator is not resting
on all four rollers.
Normal when refrigerator
is first plugged in.
Often occurs when large
amounts of food are
placed in refrigerator.
Door left open.
Hot weather or frequent
door openings.
Temperature controls set
at the coldest setting.
• Check to see if package is holding door open.
• This indicates that there is a good seal on the freezer
door. If the freezer door does not automatically close after
popping open, the rollers need adjusting. See
• See
• Wait about 40 minutes for defrost cycle to end.
• Move the refrigerator and freezer control to a
• Push the plug completely into the outlet.
• Replace fuse or reset the breaker.
• Adjust leveling legs (See
• Wait 24 hours for the refrigerator to completely
cool down.
• This is normal.
• This is normal.
• See
Leveling Legs
Rollers and Leveling Legs
temperature setting.
About the controls
.
.
Rollers and Leveling Legs
.
Rollers and
).
Refrigerator or freezer
compartment too warm
Frost or ice crystals
on frozen food
(frost within package
is normal)
Frequent “buzzing”
sound
water supply to the refrigerator
has not been connected.
Small or hollow cubes
Temperature control not set
cold enough.
Warm weather or frequent
door openings.
Door left open.
Freezer door popped open.
Door left open.
Too frequent or too long
door openings.
Food blocking freezer air vents.
Icemaker feeler arm is in the
ON (down) position, but the
Water filter clogged.
• See
• Set the temperature control one step colder.
See
• Check to see if package is holding door open.
• See the problem
• Check to see if package is holding door open.
• Set the feeler arm to the STOP (up) position. Keeping it
• Replace filter cartridge with new cartridge or with plug.
About the controls
About the controls
refrigerator door is closed
• Move items away from the back wall of the freezer.
in the ON (down) position will damage the water valve.
.
.
Freezer door pops open when
.
23
Page 24
Before you call for service…
Troubleshooting Tips
Problem Possible Causes What To Do
Automatic icemaker
(on some models)
does not work
Ice cubes stuck in icemaker.
Ice cubes have
odor/taste
Slow ice cube freezing
to begin making ice cubes.
Ice maker feeler arm is not
set ON.
Water supply turned off or
not connected.
Freezer compartment
too warm.
Piled up cubes in the storage
bin cause the icemaker
to shut off.
(Green power light on
icemaker blinking.)
Ice storage bin needs cleaning.
Food transmitting odor/taste
to ice cubes.
Interior of refrigerator
needs cleaning.
Door left open.
Temperature control not set
cold enough.
cool down.
• Check to see if package is holding door open.
• Move the feeler arm to the ON position.
• See
• Wait 24 hours for the refrigerator to completely
• Level cubes by hand.
• Turn off the icemaker, remove cubes and turn the
• Empty and wash bin. Discard old cubes.
• Wrap foods well.
• See
• See
Installing the water line
icemaker back on.
Care and cleaning
About the controls.
• A newly installed refrigerator may take 12–24 hours
.
.
Moisture forms on
cabinet surface
between the doors
Refrigerator has odor
replace every three months.
Moisture collects inside
(in humid weather, air
carries moisture into
refrigerator when doors
are opened)
Refrigerator compartment
light does not work
return with long or frequent door openings.
Not unusual during
periods of high humidity.
Foods transmitting
odor to refrigerator.
Interior needs cleaning.
Too frequent or too
long door openings.
Open containers of water or
warm food in the refrigerator.
No power at outlet.
Light bulb burned out or loose.
• Wipe surface dry; then adjust the fresh food control
• Foods with strong odors should be tightly wrapped.
• Keep an open box of baking soda in the refrigerator;
• See
• Cover or seal open containers. During a defrost cycle,
moisture will be removed from the refrigerator, but may
setting one number higher and check again in 24 hours.
Care and cleaning
• Replace fuse or reset the breaker.
• See
Replacing the light bulbs
.
24
.
Page 25
Problem Possible Causes What To Do
GEAppliances.com
Hot air from bottom
of refrigerator
heat be expelled in the
area under the refrigerator.
Some floor coverings will
discolor at these normal
and safe temperatures.
Food freezing in
the refrigerator
Orange glow
in the freezer
Door bins do not fit
in the door
Controls do not light up
Normal air flow cooling
motor. In the refrigeration
process, it is normal that
Food too close to the air vent
at the back of the refrigerator.
Refrigerator control is set
too cold.
Defrost heater is on.
The freezer door bins are
a different size than the
refrigerator door bins.
Some models do not have
lighted controls.
Refrigerator light bulb burned
out or loose.
temperature setting one increment at a time.
• Move the refrigerator control to a warmer
• This is normal.
• Try to install the bins in both doors.
• Move the food away from the air vent (near the
controls).
• If you can read white numbers on the control setting,
the model does not have lighted controls.
• See Replacing the light bulbs.
Water has poor
taste/odor
Water in first glass
is warm
No water or ice cube
production
Water dispenser has not been
used for a long time.
Normal when refrigerator
is first installed.
Water dispenser has not been
used for a long time.
Water system has been drained.
Supply line or shutoff valve
is clogged.
• Dispense water until all water is system is
• Call a plumber.
• Dispense water until all water in system is
replenished.
• Wait 24 hours for the refrigerator to completely
cool down.
replenished.
• Allow several hours for replenished supply to chill.
25
Page 26
Refrigerator Warranty.
For US Customers,
all warranty service provided by our Factory Service
Centers, or an authorized Customer Care® technician. To schedule
service, on-line, 24 hours a day, visit us at GEAppliances.com, or call
800.GE.CARES (800.432.2737). Please have serial number and model
number available when calling for service.
In Canada,
call 800.561.3344.
For the Period of: GE Will Replace
One Year
From the date of the original
purchase
Any part
During the
service to replace the defective part.
of the refrigerator which fails due to a defect in materials or workmanship.
limited one-year warranty,
What is Not Covered:
■
Service trips to your home to teach you how to use the product.
■
Improper installation, delivery or maintenance.
■
Failure of the product if it is abused, misused, or used for other
than the intended purpose or used commercially.
■
Loss of food due to spoilage.
■
Replacement of house fuses or resetting of circuit breakers.
■
Damage caused after delivery.
■
Replacement of the water filter cartridge, if included, due to
water pressure that is outside the specified operating range or
due to excessive sediment in the water supply.
■
Replacement of the light bulbs, if included, or water filter
cartridge, if included, other than as noted above.
Staple your receipt here.
Proof of the original
purchase date is needed
to obtain service under the
warranty.
GE will also provide,
■
Damage to the product caused by accident, fire, floods or acts of
God.
■
Incidental or consequential damage caused by possible defects
with this appliance.
■
Product not accessible to provide required service.
■
Damage caused by a non-GE Brand water filter.
■
Damage to finish (rust, tarnish, or small blemishes) must be
reported within 48 hours following delivery of appliance.
■
Products which are not defective, broken, or which are working as
described in the owner’s manual.
free of charge,
all labor and related
(;&/86,212),03/,(':$55$17,(6³<RXUVROHDQGH[FOXVLYHUHPHG\LVSURGXFWUHSDLUDVSURYLGHGLQ
this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or
fitness for a particular purpose, are limited to one year or the shortest period allowed by law
For US Customers:
This warranty is extended to the original purchaser and any succeeding owner for products
.
purchased for home use within the USA. If the product is located in an area where service by a GE Authorized
Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product
to an Authorized GE Service location for service. In Alaska, the warranty excludes the cost of shipping or service
calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor US:
For Customers in Canada:
This warranty is extended to the original purchaser and any succeeding owner for
General Electric Company. Louisville, KY 40225
products purchased in Canada for home use within Canada. In-home warrant service will be provided in areas
where it is available and deemed reasonable by Mabe to provide.
Warrantor Canada:
MC Commercial, Burlington, Ontario, L7R 5B6
26
Loading...