Page 1
GTD84GCSN/GCPN
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
EXHAUST OPTION: When viewed from the front
of the unit, exhaust 3-way via rear, left and bottom.
Dryer is shipped exhausted to the rear. Alternate
exhausting knockouts are supplied.
GAS: An individual, properly-grounded branch circuit,
with a three-prong grounding-type receptacle, protected
by a 15 or 20 amp circuit breaker or a time-delay fuse is
required.
GAS DRYER ELECTRIC RATING: 120V, 60Hz, 6A
GAS (BTU/HR): 22,000. Factory-equipped for
natural gas. Tested for LP gas. LP gas supply requires
a conversion kit. Check installation instructions for
correct kit and have a qualified gas technician install a
conversion kit. See dryer ducting information for proper
installation.
NOTE: Dryer wall outlet must be located within 36" of
service cord entry and accessible when dryer is mounted
in position.
INS TA LLATI O N IN F O RMATI O N: For complete
information, see installation instructions packed with
your dryer.
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will be stated on a
label on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces
are: 0" either side; 1" front, top and rear
- Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a
ga s d r yer.
BATHROOM OR BEDROOM INSTALLATION:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local
codes, with the National Electric Code and National Fuel Gas Code, ANSI
Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET
INS TA LLATI O N:
- Minimum clearances to combustible surfaces are: 0" both sides; 1" rear
DRYER EXHAUSTING INFORMATION :
- Use metal duct only, vertical and horizontal ducting.
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Speci fication Created 7/19
Page 2
GTD84GCSN/GCPN
22 1/2"
30 1/2"
27"
3 1/2"
1 3/4"
5 1/4"
8"
40 1/2"
48"
27"
7"
Power Cord 4 1/2"
11 3/4"
5
Back View
Power
Cord Hole
4-1/2
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
POWER CORD LOCATIONS
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Speci fication Created 7/19
Page 3
GTD84GCSN/GCPN
GE Dryer Vent
2-1/2
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry
FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED
WITH YOUR DRYER.
DUCTING MATERIALS:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust
duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can
be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer
to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type)
duct may be used ONLY in installations where rigid metal or f lexible metal (semi-rigid) ducting
cannot be used AND where a 4" diameter can be maintained throughout the entire length of
the transition duct. Please see installation instruction packed with your dryer for complete
instructions when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or
bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length
should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard
or moisture could cause damage. Never terminate the exhaust into a common duct or plenum
with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,
PLEASE CALL 1-800-GE-CARES.
DRYER EXHAUSTING INFORMATION—
USE METAL DUCT ONLY VERTICAL AND
HORIZONTAL DUCTING
BEST PERFORMANCE
Maximum length
of 4" dia rigid
A
4
Domestic dryer models
Long Vent 6.1-7.4 cu. ft.
capacity electric & gas
For every extra 90° elbow, reduce the allowable vent system
length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
When calculating the total vent system length, you must add all
the straight portions and elbows of the system (including the
transition duct.
B
Number
of 90°
metal duct
Exhaust hood type
A
turns
0 120 ft. 90 ft.
1 100 f t. 75 ft.
2 85 ft. 65 ft.
3 70 ft. 55 f t.
4 60 f t. 45 ft.
5 55 ft. 35 ft.
4"
opening
opening
B
2-1/2"
Speci fication Created 7/19
Page 4
GTD84GCSN/GCPN
My Cycle
Sound
TIMED DRYACTIVE WEAR
DELICATES
MIXED LOAD
SANITIZE
COTTONS
Normal
JEANS
eco
Dry
Wrinkle
Care
Delay
Dry
Dewrinkle
Refresh
Controls
Drying
Cooling
Pause
Damp
Sensing
Cycle Status:
On Damp
Less Dry
Dry
Lint Filter
Clean
More Dry
No Heat
Low
Medium Check Vent
High
Est. Time
Remaining
20 min.
40 min.
60 min.
90 min.
10 min.
20 min.
Time TempLevel
More
Time
Less
Time
SMART
Large LoadsSmall Loads
Save My
Cycle*
* Hold 3
Seconds
Control
Lock*
TOWELS
Sheets
QUICK
DRY
BULKY
Comforter
*
STEAM CYCLES
Warm
Up
Select
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry
FEATURES AND BENEFITS
Steam – Dewrinkle and refresh your laundry right in the dryer thanks to innovative built-in
steam technology.
Built-in WiFi – Enjoy the ultimate in convenience and the latest in technology with the ability to
monitor and control your laundry from anywhere and receive real-time notifications and updates.
HE Sensor Dry – Prevent over-drying and get more wear out of your clothing thanks to
innovative dual thermistor technology, that continually monitors temperature and moisture in
the dryer.
Up to 120 ft. venting – Maximize your dryer’s performance with innovative venting, designed
to provide optimal airflow, enhanced drying ability, and flexible installation.
Wrinkle Care – Spend less time ironing thanks to an innovative wrinkle care system that
allows you to tumble clothes without heat to reduce creasing.
Digital Touch Controls – Quickly and easily adjust your settings to do laundry your way using
these sleek controls.
My Cycle Settings – Streamline your laundry by choosing your favorite dryer settings on any
cycle and saving them for future use.
Quick Dry – Dry a full load in less time thanks to innovative quick dry technology.
Damp Alert – Be notified when clothes are the ideal dampness to remove from the dryer for
wrinkle-free results.
Dry Level Options – Four different drying levels to dry the way you want.
Temperature Options – Four different temperatures for full control over the drying process.
Sanitize Cycle – Reduce certain types of bacteria by 99.8% with this cycle.
Model GTD84GCSNWS – White with silver backsplash
Model GTD84GCPNDG – Diamond Gray
Speci fication Created 7/19
Loading...