Page 1
GTD72EBSN/EBPN
22 1/2"
30 1/2"
27"
3 1/2"
1 3/4"
3 1/4"
8"
38 1/2"
46"
27"
5"
Power Cord 4 1/2"
11 3/4"
5
Power
Cord Hole
4-1/2
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Electric Dryer With HE Sensor Dry
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRIC DRYER RATING:
240V 5600W 24A 60Hz
208V 4400W 22A 60Hz
EXHAUST OPTION: 4-way rear, right, left and bottom
CIRCUIT REQUIREMENTS: An individual, properly-grounded branch circuit,
protected by a 30-amp circuit breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be located within 36" of service cord entry and
acessible when dryer is mounted in position.
INS TA LLATI O N IN F O RMATI O N: For complete information, see installation
instructions packed with your dryer.
Special Installation Requirements
ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will be stated
on a label on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side; 1" front, top and rear
- Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in.
of open area equally distributed. If this closet contains both a washer and a dryer, doors must
contain a minimum of 120 sq. in. of open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local codes, with
the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
- Minimum clearances to combustible surfaces are: 0" both sides; 1" rear
DRYER EXHAUSTING INFORMATION : Use metal duct only, vertical and horizontal ducting.
SIDE VIEW
POWER CORD LOCATIONS
REAR VIEW
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Listed by
Underwriters
Laboratories
BACK VIEW
Speci fication Created 7/19
Page 2
GTD72EBSN/EBPN
GE Dryer Vent
2-1/2
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Electric Dryer With HE Sensor Dry
FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED
WITH YOUR DRYER.
DUCTING MATERIALS:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust
duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting
can be used (Kit WX08X10077). In special installations, it may be necessary to connect the
dryer to the house vent using a f lexible metal (foil-type) duct. A UL-listed flexible metal (foiltype) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid)
ducting cannot be used AND where a 4" diameter can be maintained throughout the entire
length of the transition duct. Please see installation instruction packed with your dryer for
complete instructions when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or
bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct
length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard
or moisture could cause damage. Never terminate the exhaust into a common duct or plenum
with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,
PLEASE CALL 1-800-GE-CARES.
DRYER EXHAUSTING INFORMATION—
USE METAL DUCT ONLY VERTICAL AND
HORIZONTAL DUCTING
BEST PERFORMANCE
Maximum length
of 4" dia rigid
A
4
Domestic dryer models
Long Vent 6.1-7.4 cu. ft.
capacity electric & gas
(GTD33, GTD42, GTD45,
GTD65, GTX22, GTX33, GTX42
and GTX65)
For every extra 90° elbow, reduce the allowable vent system
length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
When calculating the total vent system length, you must add all
the straight portions and elbows of the system (including the
transition duct.
B
Number
of 90°
metal duct
Exhaust hood type
A
turns
0 120 ft. 90 ft.
1 100 f t. 75 ft.
2 85 ft. 65 ft.
3 70 ft. 55 ft.
4 60 f t. 45 ft.
5 55 ft. 35 ft.
4"
opening
opening
B
2-1/2"
Speci fication Created 7/19
Page 3
GTD72EBSN/EBPN
Est. Time Remaining
WARM UP
SANITIZE
BULKY
Comforter
DELICATES
JEANS AIR FLUFF
TIMED DRY
TOWELS
Sheets
CASUALS
QUICK DRY
MIXED LOAD
COTTONS
Normal
Wrinkle
Care
ecoDry
More
Time
Less
Time
Delay
Dry
Sound
My
Cycle
Damp
Alert
Time Level Temp
Damp
Less Dry
Dry
More Dry
No Heat
Medium
Low
High
60
10
20
40
90 min.
Delay Drying Cooling Done
Drum
Light*
Control Lock*
Save My
Cycle*
* Hold 3 Seconds
Time Dry Cycles
G
T
D
7
2
E
(
G
)
B
S
N
W
S
,
G
T
D
7
2
E
(
G
)
B
P
N
D
G
2
3
4
D
2
2
9
8
P
0
1
0
R
E
V
.
1
1
,
2
3
4
D
2
3
1
3
G
0
1
0
,
2
3
4
D
2
4
5
6
G
0
1
0
/
G
0
1
1
GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Electric Dryer With HE Sensor Dry
FEATURES AND BENEFITS
HE Sensor Dry – Prevent over-drying and get more wear out of your clothing thanks
to innovative dual thermistor technology, that continually monitors temperature and
moisture in the dryer.
Up to 120 ft. venting – Maximize your dryer’s performance with innovative venting,
designed to provide optimal airflow, enhanced drying ability, and flexible installation.
Wrinkle Care – Spend less time ironing thanks to an innovative wrinkle care system that
allows you to tumble clothes without heat to reduce creasing.
My Cycle Settings – Streamline your laundry by choosing your favorite dryer settings on
any cycle and saving them for future use.
Quick Dry – Dry a full load in less time thanks to innovative quick dry technology.
Damp Alert – Be notified when clothes are the ideal dampness to remove from the dryer for
wrinkle-free results.
Dry Level Options – Four different drying levels to dry the way you want.
Temperature Options – Four different temperatures for full control over the drying process.
Sanitize Cycle – Reduce certain types of bacteria by 99.8% with this cycle.
Warm Up – Quickly warm up your clothes and release set wrinkles.
ENERGY STA R® qualified - Meets or exceeds federal guidelines for energy efficiency for
year-round energy and money savings
Check Vent Alert - Ensure optimal drying performance with this notification to alert you
when your dryer vent needs to be cleaned.
Model GTD72EBSNWS – White with silver backsplash
Model GTD72EBPNDG – Diamond Gray
Listed by
Underwriters
Laboratories
Speci fication Created 7/19
Loading...