Page 1
GTD45GASJ
GE® Series 7.2 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer with HE Sensor Dry
DimEnsiOns anD installatiOn infOrmatiOn (in inchEs)
Exhaust OptiOn: When viewed from the front
of the unit, exhaust 3-way via rear, left and bottom.
Dryer is shipped exhausted to the rear. Alternate
exhausting knockouts are supplied.
Gas: An individual, properly-grounded branch
circuit, with a three-prong grounding-type receptacle,
protected by a 15 or 20 amp circuit breaker or a timedelay fuse is required.
Gas DryEr ElEctric ratinG: 120V, 60Hz, 6A
Gas (Btu/hr): 22,000. Factory-equipped for
natural gas. Tested for LP gas. LP gas supply requires
a conversion kit. Check installation instructions for
correct kit and have a qualified gas technician install
a conversion kit. See dryer ducting information for
proper installation.
nOtE: Dryer wall outlet must be located within 36"
of service cord entry and accessible when dryer is
mounted in position.
installatiOn infOrmatiOn : For complete
information, see installation instructions packed with
your dryer.
spEcial installatiOn rEquirEmEnts
alcOvE Or clOsEt installatiOn:
- If your dryer is approved for installation in an alcove or closet, it will be stated on a label
on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side; 3" front and rear.
- Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
- Closet doors must be louvered or otherwise ventilated and must contain a minimum of
60 sq. in. of open area equally distributed. If this closet contains both a washer and a
dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BathrOOm Or BEDrOOm installatiOn:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local codes,
with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
minimum clEarancEs OthEr than alcOvE Or clOsEt installatiOn:
- Minimum clearances to combustible surfaces are: 0" both sides; 3" rear.
DryEr ExhaustinG infOrmatiOn :
- Use metal duct only, vertical and horizontal ducting.
For answers to your Monogram, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Speci fication Revised 10/15
Page 2
GTD45GASJ
22 1/2"
29 1/2"
26"
3 1/2"
1 3/4"
3 1/4"
8"
37 1/2"
44"
27"
5"
Power Cord 4 1/2"
11 3/4"
5
Power
Cord Hole
4-1/2
GE® Series 7.2 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer with HE Sensor Dry
DimEnsiOns anD installatiOn infOrmatiOn (in inchEs)
siDE viEw rEar viEw
pOwEr cOrD lOcatiOns
Back viEw
For answers to your Monogram, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Speci fication Revised 10/15
Page 3
GtD45GasJ
A
B
4
GE Dryer Vent
B
2-1/2
GE® Series 7.2 Cu. Ft. Capacity Aluminized Alloy
DryEr ExhaustinG infOrmatiOn—usE mEtal
Duct Only vErtical anD hOrizOntal DuctinG
Drum Gas Dryer with HE Sensor Dry
fOr cOmplEtE infOrmatiOn, sEE installatiOn instructiOns
packED with yOur DryEr.
DuctinG matErials:
For best performance, this dryer should be vented with 4" diameter all rigid metal
exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal
(semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it
may be necessary to connect the dryer to the house vent using a flexible metal
(foil-type) duct. A UL-listed f lexible metal (foil-type) duct may be used ONLY in
installations where rigid metal or flexible metal (semi-rigid) ducting cannot be
used AND where a 4" diameter can be maintained throughout the entire length of
the transition duct. Please see installation instruction packed with your dryer for
complete instructions when using flexible metal (foil type) ducting.
Exhaust lEnGth calculatiOn:
1. Determine the number of 90° turns needed for your installation. If you exhaust
to the side or bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be
tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45°
turns within the duct length should be treated as a 90° elbow. A turn over 45°
should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
cautiOn: For personal safety do not terminate exhaust into a chimney, under
any enclosed house f loor (crawl space), or into an attic, since the accumulated lint
could create a fire hazard or moisture could cause damage. Never terminate the
exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back
drafts, bird nesting, etc. The wall cap must also be located at least 12" above the
ground or any other obstruction with the opening pointed down.
fOr mOrE infOrmatiOn On vEntinG kits anD accEssOriEs,
plEasE call 1-800-GE-carEs.
For answers to your Monogram, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
A
Domestic dryer models
GE Front Load Long Vent 7.0
cu. ft. capacity electric dryer
(GF DL)
Long Vent 6.1-7.4 cu. ft.
capacity electric & gas
(GTD42, GTD45, GTD65,
GTX42 and GTX65
Long Vent 61 -7.4 cu. ft.
capacity electric & gas
(GTD42, GTD45, GTD65,
GTX42 and GTX60)
All 6.0 - 8 .3 cu. ft. capacity
models electric and gas dryers
(GFDS, GFDR, G FDN, GTDS,
GTDN, GHDN , GHDS, GTDP,
GLDP, GTD, HTDP, HTDX)
DCVH480
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
Laundry Center GUD27
Laundry Center GUD24
BEST PERFORMANCE
Maximum length
of 4" dia rigid
metal duct
Exhaust hood t ype
Number
of 90°
turns
0 200 ft. 175 ft.
1 185 f t. 165 ft.
2 175 ft. 155 ft.
3 165 ft. 145 ft.
4 155 ft. 135 ft.
5 145 ft. 125 ft.
0 150 ft. 125 ft.
1 135 ft. 115 ft.
2 125 ft. 105 ft.
3 115 f t. 95 ft.
4 105 ft. 85 ft.
5 95 f t. 75 ft.
0 120 ft. 90 ft.
1 100 ft. 75 ft.
2 85 f t. 65 ft.
3 70 ft. 55 ft.
4 60 ft. 45 ft.
5 55 f t. 35 ft.
0 90 ft. 60 ft.
1 60 ft. 45 ft.
2 45 ft. 35 ft.
3 35 f t. 25 ft.
4 25 ft. 15 ft.
0 90 ft. 60 ft.
1 60 ft. 45 ft.
2 45 ft. 35 ft.
3 35 f t. 25 ft.
0 46 ft. 37 f t.
1 37 ft. 30 ft.
2 30 ft. 22 ft.
3 23 f t. 15 ft.
0 56 ft. 42 ft.
1 48 ft. 34 ft.
2 40 ft. 26 ft.
3 32 f t. 18 ft.
0 43 ft. 36 f t.
1 33 ft. 26 f t.
2 24 f t. 16 ft.
A
4"
opening
Specification Created 7/15
B
2-1/2"
opening
Page 4
GtD45GasJ
GE® Series 7.2 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer with HE Sensor Dry
fEaturEs anD BEnEfits
HE Sensor Dry – Keep your clothes looking and feeling their best. Dual
thermistors continually monitor temperature with a sensor bar that measures
moisture to prevent over-drying
Up to 120 ft. venting capability – Provides flexible installation
Extended Tumble – Freshly tumbles your garments periodically for up to 8 hours
when unable to move clothing to the dryer right away
End-of-cycle signal – Alerts you when the load is done, so clothes can be
removed before wrinkles set in
Model GTD45GASJWS – White with silver backsplash
Specification Created 7/15
Loading...