Specification Created 8/00
R
Listed by
Underwriters
Laboratories
GE Appliances
GSM2130/10F—GE Spacemaker®Undersink Dishwasher
Plumbing/Electrical Rough-In Dimensions (in inches)
2" From
cabinet
6
4
2" From
floor
19" From
wall
Cable 24"
from wall
3
White (neutral)
Black (line)
Ground
Plumbing and
wiring must enter
within this area
from either side,
rear or bottom
FRONT VIEW
Hot
Cold
Note: Undersink dishwashers can be installed only under sinks and not
under other appliances.
Plumbing—Hot Water Only: Use 3/8" O.D. copper tubing or 1/2" O.D.
plastic tubing minimum inlet line. Water valve has 3/8" internal threads.
Hand cut-off valve is recommended.
Electrical: Fuse circuit with 15 amp or 20 amp standard fuse or circuit
breaker. Total amp load is 8.6. Dishwasher operates on 120V, 60HZ power,
Two-wire cable (14 Ga. Min.) with ground must be installed.
Specifications: Inlet water temperature recommended—minimum 120°F
at dishwasher. Inlet water pressure required—15 to 120 lbs./sq. inch.
Note: All rough-in, both plumbing and electrical, must be completed before
the dishwasher is installed. All plumbing and electrical work must be in
accordance with local codes.
For answers to your Monogram,
®
GE Profile Performance Series,
™
GE Profile™or GE appliance questions, call
GE Answer Center
®
service, 800.626.2000.
Specification Created 8/00
R
Listed by
Underwriters
Laboratories
GE Appliances
GSM2130/10F—GE Spacemaker®Undersink Dishwasher
Rough-In for Installation with Disposer
Dimensions (in inches)
Rear View Plumbing Arrangement
Dimensions (in inches)
6
4
10"
from
cabinet
Allow a 5"
radius to
prevent kinking
1-1/2" MAX.
dia. hole
Directional flow tee
Waste air gap
12" From wall
Waste tee
or disposer
Remove hopper plug
before connecting
dishwasher drain
FRONT VIEW
Drain
connection
To
air
gap
Cold water
Hot water
Valve to shut off
water to dishwasher
Hot water supply
to dishwasher
1-1/2"
Directional
flow tee
Dishwasher
drain hose
Electrical
junction box
(on dishwasher)
Dishwasher
water inlet
valve
6" Double-bowl
stainless steel sink
Sink
strainer
assembly
Countertop
25" deep
1-1/2" thick
1-1/2" Close
elbow
GFC290/300/700
Disposall
®
unit
Spacemaker
®
dishwasher
Note: A close-fitting elbow or special
shallow sink strainer is necessary to
provide clearance between sink drain
and dishwasher. Dishwasher furnished
with 1/2" I.D. drain hose, 78" long. If
using copper tubing, 2" length of 1/2"
I.D. rubber hose must be provided to
connect copper tubing to pump outlet.
Disposer should have 7/8" I.D. dishwasher
drain connector.
For answers to your Monogram,
®
GE Profile Performance Series,
™
GE Profile™or GE appliance questions, call
GE Answer Center®service, 800.626.2000.
Specification Created 8/00
R
Listed by
Underwriters
Laboratories
GE Appliances
GSM2130/10F—GE Spacemaker®Undersink Dishwasher
Cabinet Cut-Out for Sink Dimensions (in inches)
Cabinet Rough-In Dimensions (in inches)
12
3-1/4
12-1/2
5
5
Sink
installation
cutout
8" x 20" Adjacent
cabinet rear cutout
Cabinet side
adjacent to D/W
FRONT VIEW
Cabinet cutouts for offset single and double
bowl sinks. Dishwasher not provided with
complete enclosure. Enclosures for sides,
top, bottom and back must be provided by
installer at time of installation.
11-3/4
C
B
Access insert
Detail D
Panel Thickness
Door insert
Front
of
Panel
A
1-1/2
1/2
When using GPF325
1/4" custom dishwasher
door and access panel kit.
When using GPF375
3/4" custom dishwasher
door and access panel kit.
1/4
3/4
Cabinet Rough-In Note: Either single- or double-bowl sink may
be used, centered or offset, as shown in the front view illustration.
The 20-1/2" maximum dimension from wall to front of sink bowl
must be accurate if dishwasher is to fit properly under sink. Water
lines to sink faucet and drain from sink can be run through area “A.”
HOT WATER line to dishwasher is installed in area “B.”
Garbage disposer, water lines to faucet, trap, waste air gap and
water cutoff valve are installed in 12" wide cabinet shown in area
“C.” Sink opening for garbage disposer must be dimensioned as
shown in front view, area “C” (7-1/2"). This will provide clearance
for the disposer and plumbing in cabinet “C” when using double
bowl sink.
If the sink bowl is more than 20-1/2" maximum specified distance
form the wall, or if the base cabinet is less than the 24" minimum
depth from the wall, a gap between the tub front flange and the
front of the base cabinet may result.
Undersink Dishwasher
Wood Insert Dimensions (in inches)
Countertop 1-1/2" MIN. thick
FRONT VIEW
7-1/2
6" MAX.
24 12"
MIN.
Floor
Toe
kick
area
Front of cabinet
Flange
4" MAX.
11-3/4"
MAX. Plumbing
1-1/4"
MIN. I.R.
34-1/4
± 1/4
3/4" MIN.
Wall
Floor
6" MAX.
C
L
11" MIN
Drain
20-1/2" MAX.
Sink bowl
1" MAX. to
sink flange
10-1/4" MAX.
Plumbing depth
SIDE VIEW
Dishwasher
10-1/4" MAX.
A
24"
min. cabinet
For answers to your Monogram,
®
GE Profile Performance Series,
™
GE Profile™or GE appliance questions, call
GE Answer Center®service, 800.626.2000.
GE Appliances
Specification Created 8/00
GSM2130/10F—GE Spacemaker®Undersink Dishwasher
Nautilus
Q
u
ie
t P
o
w
e
r
M
o
to
r
S
T
A
R
T
S
H
O
R
T
W
A
S
H
O
F
F
H
O
T
S
T
A
R
T
O
P
T
I
O
N
S
R
I
N
S
E
O
N
L
Y
(HEA
TED DRY OFF)
P
L
A
T
E
W
A
R
M
E
R
(HEATED DRY ON)
Features and Benefits
• 2 Wash Levels
• 5 Cycle Selections: Pots & Pans, Normal Wash, Short Wash,
Plate Warmer and Rinse Only/Hold
• 12 Options including Heated Dry On/Off Options
• HotStart
™
• SpaceMaker™Upper Rack
• Deluxe Lower Rack
• Deluxe Silverware Basket
• Rinse Aid Dispenser
• PermaTuf
™
Tub and Door Liner
• QuietPower
™
Motor
• Model GSM2130FWW - White on white
• Model GSM2110FAA - Almond on almond
Loading...