GE Appliances
GSM2100GWW/CC—GE Spacemaker® Under-the-Sink Dishwasher
Plumbing/Electrical Rough-In Dimensions (in inches)
|
|
FRONT VIEW |
|
|
|
|
Plumbing and |
|
|
|
|
wiring must enter |
|
|
|
|
within this area |
Cold |
|
|
4 |
from either side, |
||
|
rear or bottom |
Hot |
||
|
|
|
|
|
6 |
19" From |
Cable 24" |
|
|
|
|
wall |
|
|
|
|
from wall |
|
|
|
|
|
|
Note: Undersink dishwashers can be installed only under sinks and not under other appliances.
Plumbing—Hot Water Only: Use 3/8" O.D. copper tubing or 1/2" O.D. plastic tubing minimum inlet line. Water valve has 3/8" internal threads. Hand cut-off valve is recommended.
Electrical: Fuse circuit with 15 amp or 20 amp standard fuse or circuit breaker. Total amp load is 8.6. Dishwasher operates on 120V, 60HZ power, Two-wire cable (14 Ga. Min.) with ground must be installed.
Specifications: Inlet water temperature recommended—minimum 120°F at dishwasher. Inlet water pressure required—15 to 120 lbs./sq. inch.
Note: All rough-in, both plumbing and electrical, must be completed before the dishwasher is installed. All plumbing and electrical work must be in accordance with local codes.
2" From |
|
|
cabinet |
2" From |
3 |
floor Ground Black (line)
White (neutral)
Specification Created 11/01
For answers to your Monogram,® GE Profile™ or GE appliance questions, visit our website at GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Listed by
R |
Underwriters |
As an ENERGY STAR® Partner, |
Laboratories |
meets the ENERGY STAR® |
|
|
|
GE has determined that this product |
|
|
guidelines for energy efficiency. |
GE Appliances
GSM2100GWW/CC—GE Spacemaker® Under-the-Sink Dishwasher
Rough-In for Installation with Disposer |
Rear View Plumbing Arrangement |
Dimensions (in inches) |
Dimensions (in inches) |
|
|
Waste air gap |
6" Double-bowl |
|
Sink |
|
Countertop |
|
|
|
stainless steel sink |
|
strainer |
|
|||
|
|
|
|
|
||||
|
|
To |
|
|
|
assembly |
25" deep |
|
|
|
air |
|
|
|
|
|
1-1/2" thick |
|
|
gap |
GFC290/300/700 |
|
|
|
|
|
Directional flow tee |
|
|
|
|
|
|
||
|
Disposall® |
|
|
|
|
|
||
FRONT VIEW |
|
unit |
|
|
|
|
1-1/2" Close |
|
|
Drain |
Waste tee |
1-1/2" |
|
|
|
|
elbow |
connection |
|
|
|
|
|
|||
or disposer |
Directional |
Spacemaker |
® |
|
||||
4 |
1-1/2" MAX. |
Remove hopper plug |
flow tee |
|
|
|||
|
dishwasher |
|
|
|||||
|
dia. hole |
before connecting |
|
|
|
|
|
|
|
|
dishwasher drain |
Cold water |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12" From wall |
|
Hot water |
|
|
|
|
Dishwasher |
|
|
Valve to shut off |
|
|
|
|
||
6 |
|
|
|
|
|
|
||
|
|
water to dishwasher |
|
|
|
|
water inlet |
|
|
|
|
Hot water supply |
|
|
Electrical |
valve |
|
|
|
|
Dishwasher |
junction box |
||||
|
|
|
to dishwasher |
|||||
10" |
|
|
(on dishwasher) |
|||||
Allow a 5" |
|
drain hose |
|
|||||
from |
|
|
|
|
|
|
||
cabinet |
radius to |
|
|
|
|
|
|
|
|
prevent kinking |
|
|
|
|
|
|
Note: A close-fitting elbow or special shallow sink strainer is necessary to provide clearance between sink drain and dishwasher. Dishwasher furnished with 1/2" I.D. drain hose, 78" long. If using copper tubing, 2" length of 1/2" I.D. rubber hose must be provided to connect copper tubing to pump outlet.
Disposer should have 7/8" I.D. dishwasher drain connector.
For answers to your Monogram,® GE Profile™ or GE appliance questions, visit our website at GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Specification Created 11/01
Listed by Underwriters
R Laboratories
As an ENERGY STAR® Partner, GE has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.