GE GSM2100GWW, GSM2100GCC Specification
Specification Created 11/01
R
Listed by
Underwriters
Laboratories
GE Appliances
GSM2100GWW/CC—GE Spacemaker®Under-the-Sink Dishwasher
Plumbing/Electrical Rough-In Dimensions (in inches)
2" From
cabinet
6
4
2" From
floor
19" From
wall
Cable 24"
from wall
3
White (neutral)
Black (line)
Ground
Plumbing and
wiring must enter
within this area
from either side,
rear or bottom
FRONT VIEW
Hot
Cold
Note: Undersink dishwashers can be installed only under sinks and not
under other appliances.
Plumbing—Hot Water Only: Use 3/8" O.D. copper tubing or 1/2" O.D.
plastic tubing minimum inlet line. Water valve has 3/8" internal threads.
Hand cut-off valve is recommended.
Electrical: Fuse circuit with 15 amp or 20 amp standard fuse or circuit
breaker. Total amp load is 8.6. Dishwasher operates on 120V, 60HZ power,
Two-wire cable (14 Ga. Min.) with ground must be installed.
Specifications: Inlet water temperature recommended—minimum 120°F
at dishwasher. Inlet water pressure required—15 to 120 lbs./sq. inch.
Note: All rough-in, both plumbing and electrical, must be completed before
the dishwasher is installed. All plumbing and electrical work must be in
accordance with local codes.
For answers to your Monogram,® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center
®
service, 800.626.2000.
As an ENERGY STAR® Partner,
GE has determined that this product
meets the ENERGY STAR®
guidelines for energy efficiency.
Specification Created 11/01
R
Listed by
Underwriters
Laboratories
GE Appliances
GSM2100GWW/CC—GE Spacemaker®Under-the-Sink Dishwasher
Rough-In for Installation with Disposer
Dimensions (in inches)
Rear View Plumbing Arrangement
Dimensions (in inches)
6
4
10"
from
cabinet
Allow a 5"
radius to
prevent kinking
1-1/2" MAX.
dia. hole
Directional flow tee
Waste air gap
12" From wall
Waste tee
or disposer
Remove hopper plug
before connecting
dishwasher drain
FRONT VIEW
Drain
connection
To
air
gap
Cold water
Hot water
Valve to shut off
water to dishwasher
Hot water supply
to dishwasher
1-1/2"
Directional
flow tee
Dishwasher
drain hose
Electrical
junction box
(on dishwasher)
Dishwasher
water inlet
valve
6" Double-bowl
stainless steel sink
Sink
strainer
assembly
Countertop
25" deep
1-1/2" thick
1-1/2" Close
elbow
GFC290/300/700
Disposall
®
unit
Spacemaker
®
dishwasher
Note: A close-fitting elbow or special
shallow sink strainer is necessary to
provide clearance between sink drain
and dishwasher. Dishwasher furnished
with 1/2" I.D. drain hose, 78" long. If
using copper tubing, 2" length of 1/2"
I.D. rubber hose must be provided to
connect copper tubing to pump outlet.
Disposer should have 7/8" I.D. dishwasher
drain connector.
For answers to your Monogram,
®
GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
As an ENERGY STAR® Partner,
GE has determined that this product
meets the ENERGY STAR®
guidelines for energy efficiency.
Loading...