
GFDN120ED
GE® Series 7.0 Cu. Ft. Capacity Front Load Electric Dryer
Dimensions anD installation information (in inches)
electric Dryer rating
120V/240V 5600W, 24A, 60Hz
120V/208V 4400W, 22A, 60Hz
exhaust options: 4-way via rear, right, left and bottom.
circuit requirements: An individual, properly
grounded branch circuit, protected by a 30-amp circuit breaker
or a time-delay fuse, is required.
note: Dryer wall outlet must be located within 36" of service
cord entry and accessible when dryer is mounted in position.
installation information : For complete information,
see installation instructions packed with your dryer.
27 32-3/16
39-3/8
4-3/8
For answers to your Monogram, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
1-3/4
Gas Pipe
3-1/2
Electrical
Listed by
Underwriters
Laboratories
Speci fication Revised 10/15

GFDN120ED
GE® Series 7.0 Cu. Ft. Capacity Front Load Electric Dryer
special installation requirements:
stac k e D i n stallation:
Brackets for stacking dryer over washer are not included with the dryer.
GEFLSTACK or part no. WE25X10018.
alcove or closet installation:
If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back.
The dryer MUST be exhausted to the outside.
Minimum clearances between dryer cabinet and adjacent walls or other
surfaces are: 0" either side, 3" front and rear.
Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
No other fuel-burning appliance shall be installed in the same closet with
a gas dryer.
Bathroom or BeDroom installation:
The dryer MUST be exhausted to the outdoors.
The installation must conform with the local codes, or in the absence of
local codes, with the National Electric Code and National Fuel Gas Code,
ANSI Z223 for gas dryers.
minimum clearance other than alcove or closet
installations:
Minimum clearances to combustible surfaces 0" both sides, 3" rear.
for more information on venting kits anD
accessories,
please call 1-800-ge-cares.
stackeD Dimensions
(in inches)
24
3-1/4
peDestal Dimensions (in inches)
sBsD137hWW - White
This optional 13" pedestal raises the door
opening and height of the washer or dryer.
Feet on 13" pedestal allow it to adjust to
13-3/8" height.
13
79-5/8
27
28-3/4
For answers to your Monogram, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Listed by
Underwriters
Laboratories
Speci fication Revised 10/15

GFDN120ED
GE® Series 7.0 Cu. Ft. Capacity Front Load Electric Dryer
special installation requirements
Dryer exhausting information – Metal duct only.
For complete information, see installation instructions packed with your dryer.
Ducting materials: For best performance, this dryer should be vented with 4" diameter all
rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid)
ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the
dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type)
duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot
be used AND where a 4" diameter can be maintained throughout the entire length of the transition
duct. Please see installation instruction packed with your dryer for complete instructions when using
flexible metal (foil type) ducting.
exhaust length calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated is shown
in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house
floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture
could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen
exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc.
The wall cap must also be located at least 12" above the ground or any other obstruction with the
opening pointed down.
for more information on venting kits anD accessories,
please call 1-800-ge-cares.
For answers to your Monogram, GE Profile™ Series
or GE® Series appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Dryer exhausting information—use metal
Duct only vertical anD horizontal Ducting
BEST PERFORMANCE
Maximum length
A
Number
of 90°
Domestic dryer models
GE Front Load Long Vent 7.0
cu. ft. capacity electric dryer
(GF DL)
Long Vent 6.0 - 8.0 cu. ft.
capacity electric & gas dryers
(GTDL and GT V)
Long Vent 7.0 cu. ft. capacity
electric & gas (GTD42, GTD45,
GTD65 , GTX42 and GTX60)
All 6.0 - 8 .3 cu. ft. capacity
models electric and gas dryers
(GFDS, GFDR, G FDN, GTDS,
GTDN, GHDN , GHDS, GTDP,
GLDP, GTD, HTDP, HTDX)
DCVH480
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
Laundry Center GUD27
Laundry Center GUD24
Listed by
Underwriters
Laboratories
of 4" dia rigid
metal duct
Exhaust hood t ype
A
4"
turns
opening
0 200 ft. 175 ft.
1 185 f t. 165 ft.
2 175 ft. 155 ft.
3 165 ft. 145 ft.
4 155 ft. 135 ft.
5 145 ft. 125 ft.
0 150 ft. 125 ft.
1 135 ft. 115 ft.
2 125 ft. 105 ft.
3 115 f t. 95 ft.
4 105 ft. 85 ft.
5 95 f t. 75 ft.
0 120 ft. 90 ft.
1 100 ft. 75 ft.
2 85 f t. 65 ft.
3 70 ft. 55 ft.
4 60 ft. 45 ft.
5 55 f t. 35 ft.
0 90 ft. 60 ft.
1 60 ft. 45 ft.
2 45 ft. 35 ft.
3 35 f t. 25 ft.
4 25 ft. 15 ft.
0 90 ft. 60 ft.
1 60 ft. 45 ft.
2 45 ft. 35 ft.
3 35 f t. 25 ft.
0 46 ft. 37 f t.
1 37 ft. 30 ft.
2 30 ft. 22 ft.
3 23 f t. 15 ft.
0 56 ft. 42 ft.
1 48 ft. 34 ft.
2 40 ft. 26 ft.
3 32 f t. 18 ft.
0 43 ft. 36 f t.
1 33 ft. 26 f t.
2 24 f t. 16 ft.
Speci fication Revised 10/15
opening
B
2-1/2"

GFDN120ED
GE® Series 7.0 Cu. Ft. Capacity Front Load Electric Dryer
features anD Benefits
DuraDrum – Provides long-lasting durability
HE Sensor Dry – Keep your clothes looking and feeling their best. Dual thermistors
continually monitor temperature with a sensor bar that measures moisture to prevent overdrying
Speed Dry – Quickly dries items and small loads for families on the go
eDry option – Energy-saving option reduces dry temperatures on select cycles without
sacrificing performance
4 heat selections – Provide the right temperatures for your clothes-drying needs
Delay start – Set the dryer to begin cycles whenever it’s convenient for you
Model GFDN120EDWW – White
Speci fication Revised 10/15