GE GFDL110EH Specification

Page 1
GFDL110EH
4-1/2
GE Appliances 7.0 Cu. Ft. Capacity Electric Dryer With 200-Ft. Long Venting
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRIC DRYER RATING
120V/240V 5600W, 24A, 60Hz
120V/208V 4400W, 22A, 60Hz
EXHAUST OPTIONS: 3-way via rear, right and bottom.
CIRCUIT REQUIREMENTS: An individual, properly
grounded branch circuit, protected by a 30-amp circuit breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be located within 36" of service cord entry and accessible when dryer is mounted in position.
INSTA L LATION I NFORM AT I ON: For complete information, see installation instructions packed with your dryer.
27 32-3/16
39-3/8
4-3/8
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
Speci fication Revised 1/16
Page 2
GFDL110EH
49-5/8
2-1/2
12
GE Appliances 7.0 Cu. Ft. Capacity Electric Dryer With 200-Ft. Long Venting
SPECIAL INSTALLATION REQUIREMENTS:
STAC KED I N STALLATI O N:
Brackets for stacking dryer over washer are not included with the dryer. GEFLSTACK or part no. WE25X10018.
ALCOVE OR CLOSET INSTALLATION:
If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
The dryer MUST be exhausted to the outside.
Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0" either side, 3" front and rear.
Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
The dryer MUST be exhausted to the outdoors.
The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTA L LATION S:
Minimum clearances to combustible surfaces 0" both sides, 3" rear.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE-CARES.
STACKED DIMENSIONS (IN INCHES)
24
3-1/4
1-3/4
Gas Pipe
Connection
3-1/2
Electrical
Connection
1/2
PEDESTAL DIMENSIONS (IN INCHES) SBSD137HWW - WHITE
This optional 13" pedestal raises the door opening and height of the washer or dryer. Feet on 13" pedestal allow
13
it to adjust to 13-3/8" height.
79-5/8
27
28-3/4
Listed by
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
Speci fication Revised 1/16
Underwriters Laboratories
Page 3
GFDL110EH
A
B
4
GE Dryer Vent
B
2-1/2
DRYER EXHAUSTING INFORMATION—USE METAL DUCT ONLY VERTICAL AND HORIZONTAL DUCTING
GE Appliances 7.0 Cu. Ft. Capacity Electric Dryer With 200-Ft. Long Venting
SPECIAL INSTALLATION REQUIREMENTS
For complete information, see installation instructions packed with your dryer.
DUCTING MATERIALS: For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed f lexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a f lexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi­rigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated is shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE-CARES.
A
Domestic dryer models
GE Front Load Long Vent 7.0 cu. ft. capacity electric dryer (GF DL)
Long Vent 6.0 - 8.0 cu . ft. capacity electric & gas dryers (GTDL and GT V)
Long Vent 7.0 cu. ft. capacity electric & gas (GTD42, GTD45, GTD65 , GTX42 and GTX60)
All 6.0 - 8 .3 cu. ft. capacity models electric and gas dryers (GFDS, GFDR, GFDN , GTDS , GTDN, GHDN, GHDS, GTDP, GLDP, GTD, HTDP, HTDX)
DCVH480
All 3.6 cu. ft. (DSKS, DSKP) electric dryers
Laundry Center GUD27
Laundry Center GUD24
BEST PERFORMANCE
Maximum length of 4" dia rigid metal duct
Exhaust hood type
Number
of 90°
turns
0 200 ft. 175 ft.
1 185 f t. 165 ft. 2 175 ft. 155 ft. 3 165 ft. 145 ft. 4 155 ft. 135 ft. 5 145 ft. 125 ft. 0 150 ft. 125 ft.
1 135 ft. 115 ft. 2 125 ft. 105 ft. 3 115 f t. 95 ft. 4 105 ft. 85 ft. 5 95 f t. 75 ft. 0 120 ft. 90 ft.
1 100 ft. 75 ft. 2 85 f t. 65 ft. 3 70 ft. 55 ft. 4 60 ft. 45 ft. 5 55 f t. 35 ft. 0 90 ft. 60 ft.
1 60 ft. 45 ft. 2 45 ft. 35 ft. 3 35 f t. 25 ft. 4 25 ft. 15 ft. 0 90 ft. 60 ft.
1 60 ft. 45 ft. 2 45 ft. 35 ft. 3 35 f t. 25 ft. 0 46 ft. 37 ft.
1 37 ft. 30 ft. 2 30 ft. 22 ft. 3 23 f t. 15 ft. 0 56 ft. 42 ft.
1 48 ft. 34 ft. 2 40 ft. 26 ft. 3 32 f t. 18 ft. 0 43 ft. 36 ft.
1 33 ft. 26 f t. 2 24 f t. 16 ft.
A
4"
opening
B
2-1/2"
opening
Listed by
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
Underwriters Laboratories
GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
Speci fication Revised 1/16
Page 4
GFDL110EH
GE Appliances 7.0 Cu. Ft. Capacity Electric Dryer With 200-Ft. Long Venting
FEATURES AND BENEFITS
Dura Drum provides long-lasting dependability
HE SensorDry™ with dual thermistors continually monitors moisture and temperature to prevent clothing wear and tear due to over-drying and inconsistent heat
Speed Dry quickly dries items and small loads for families on the go
eDry option – energy saving option reduces dry temperatures on select cycles without sacrificing performance
4 heat settings – provide the right temperature for the right drying needs
6 dry cycles – additional cycles for your clothes-drying needs
200 ft. long-venting capability – Provides flexible installation
Model GFDL110EHWW – White
Speci fication Revised 1/16
Loading...