GE GEMX2471-W1, GEMX2450-W1, GEMX2432-W1, GEMX2441-W1 Installation Manual
GE
Lighting
®
Tetra
LED Lighting System
GEMX2471-W1, GEMX2450-W1, GEMX2441-W1, GEMX2432-W1
BEFORE YOU BEGIN
Read these instructions completely and carefully.
MAX
WARNING/AVERTISSMENT
Installation Guide
24
Volt
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground Tetra® power supply enclosure.
RISK OF FIRE
• Use only UL approved wire for input/output connections.
Minimum size 18 AWG (0.82mm2)
• Follow all NEC and local codes.
Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
This Class [A] RFLD complies with the Canadian standard
ICES-003. Ce DEFR de la classe [A] est conforme à la NMB-003
du Canada.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant l’inspection, l’installation ou le déplacement.
• Assurez-vous de correctement mettre à terre l’alimentation électrique Tetra®.
RISQUES D’INCENDIE
• N’utilisez que des ls approuvés par UL pour les entrées/sorties de connexion.
Taille minimum 18 AWG (0.82mm2)
• Respectez tous les codes NEC et codes locaux.
Prepare Electrical Wiring
Electrical Requirements
• Acceptable for use in dry, damp and wet locations.
• The grounding and bonding of the LED Driver shall
be done in accordance with National Electric Code (NEC)
Article 600.
• Follow all National Electric Codes (NEC) and local codes.
• These products are only suitable for connection to a circuit from a
Class 2 power source.
• These products have not been evaluated for use when connected
to a power source that does not comply with Class 2 voltage and
energy limited supplies.
imagination at work
Components
1
5
2 3
4
UL approved 18 AWG (0.82 mm2) supply wire
1
UL approved 22-14 AWG (0.33-2.08 mm2) wire
2
connectors or 22-18 AWG (0.33-0.82 mm2)
in-line/IDC connectors
#6 or #8 (M3 or M4) screws, 1/8 inch (3.2 mm)
3
rivets, or electronic grade silicone or equivalent
Tetra® 24 Volt Power Supply
4
Layout Modules
Clean and remove all debris
1
from the inside of the channel
letter before you begin.
TC Measure Point
Measure and cut Tetra LED
2
strip to the appropriate length
for each letter. Cuts can be
made between any of the
modules.
Tetra® MAX LED modules
5
3
Remove tape backing and
stick LED modules into place.
Continue until you have
reached the end of the strip.
Use rivets, screws, or silicone
4
to secure at least every fth
LED module within the channel
letter. Use #6 (M3) or #8 (M4)
pan headed metal screws,
1/8-inch (3.2 mm) rivets, or
silicone.
Drill a 1/4-inch (6.4 mm)
5 6
hole near the LED strip and
grommet the hole for supply
wire access.
NOTE: For halo-lit applications LED modules should be mounted on UL
recognized clear acrylic or polycarbonate. The light output from the LED
system should be directed back into the sign enclosure. This will allow for
uniform backlighting of the sign and will provide simple mounting.
Clean and remove all debris
from the inside of the channel
letter. Replace sign face.
Loading...