GE GBS22HB, PDS20SB, GBS20KB, PDS20MB, PDS22MB User Manual
...
Icemaker Accessory Kit
Addendum for IM4, IM4A and IM6 Icemaker Kits
www.GEAppliances.com
197D5736P002 49-60319 12-03 JR
IMPORTANT: These
instructions are needed to
install an icemaker in your
refrigerator. To be used
with an IM4, IM4A or IM6
Icemaker Kit. Keep this
addendum with your
Owner’s Manual and
Installation Instructions.
Installation Instructions
Addendum
GBS20KB
GBS22HB
GBS22KB
PDS20MB
PDS20SB
PDS22MB
PDS22SB
These instructions
are to be used to
install an Icemaker
Kit in the models
listed below.
2
NEEDED CONTENTS OF KIT
The following are a list of the parts from the kit that will be needed to install the icemaker.
Owner’s Manual &
Installation Instructions
2
Water Line Clamp
(strain relief), for house
water line
6
Hex-Head Screw
for Water Line Clamp
5
Water Valve and
Tube Assembly
3
Hex-Head Screw, for
attaching water valve
8
Adhesive-Backed Water Tube
Fasteners, to secure plastic
water tube (4)
4
10
Water Tube Inlet
9
Phillips Head Screws,
for mounting icemaker (2)
Warranty Label
7
ICEMAKER
WARRANTY VERIFICATION
Date Installed
Dealer
11
Icemaker Fill Cup
(side-mounted)
Icemaker
1
In
s
ta
lla
t
io
n
In
s
t
r
u
c
tio
n
s
12
Hose Clamp
Installation Instructions
PARTS REQUIRED THAT CAME WITH THE REFRIGERATOR
If the fill tube has been misplaced,
call 1.800.626.2002 and order part WR02X11712.
Fill Tube with Foil
(5/8″ O.D.)
3
Installation Instructions
BEFORE YOU BEGIN
Read each step thoroughly before proceeding.
•
CAUTION – Unplug the
Refrigerator. To eliminate the danger
of electric shock during installation,
you must unplug the refrigerator from
its electrical outlet.
Flat blade and Phillips
screwdrivers
Pliers
TOOLS YOU WILL NEED
Sharp knife
INSTALL FILL TUBE
• Slide the fill tube shipped
with the refrigerator onto the
water tube inlet (10). If the fill
tube has been misplaced, call
1.800.626.2002 and order part
WR02X11712.
• Go to the back of the refrigerator.
Remove the label covering the
hole. Pull out the insulation plug
and any debris.
• On the tube side of the water
tube inlet (10), there is an
adhesive backing. Remove the
adhesive backing and slide the
tube into the hole at the back
of the refrigerator. Firmly press
on the inlet to secure it to the
refrigerator.
2
10
PREPARE FOR INSTALLATION (cont.)
• Inside the freezer, remove the two small white
plug buttons (on some models) from the side
wall. (If screws are present instead of plugs,
leave them in place.)
• Remove and discard
the large white plug
from the rear freezer
wall. Pull out the gray
insulation plug and
remove any debris.
• Remove the outlet
cover with a flat-blade
screwdriver.
3
Power
Switch
1
SET POWER SWITCH TO O (off)
Set the icemaker power switch to O (off). Leave
the power switch in the O (off) position until the
refrigerator is connected to the water supply to
prevent premature operation.
Outlet
cover
Remove side wall plug
buttons or leave screws
in place
Rear wall
plug button
Insulation
plug
PREPARE FOR INSTALLATION
• Remove the storage
basket (on some models)
by pulling it out to the
stop position and lifting
it up and out.
Note: After removing
the basket, push the
extension arms back
into the freezer
compartment.
• Remove the chiller shelf
(on some models) by
pulling it straight out.
• Remove the ice bucket
by pulling it out and
lifting it up and out.
• Remove the center
vertical shelf support
(on some models) by
lifting it and rotating
its bottom to the right.
1
Loading...