GE ECBA Installation Guide

GE

Lighting

™

Evolve

Canopy Light (ECBA)

BEFORE YOU BEGIN

Read these instructions completely and
carefully.
Save these instructions for future use.

LED Area Lighting

WARNING

Installation Guide

GEH-6029

Risk of electrical shock. Disconnect power before servicing
or installing product.

WARNING

Risk of injury or damage. Unit will fall if not installed

properly. Follow installation instructions.

CAUTION

Risk of injury. Wear safety glasses and gloves during

installation and servicing.

WARNING

This product must be installed in accordance with the
applicable installation code by a person familiar with
the construction and operation of the product and the
hazards involved.

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation. This Class [A] RFLD complies with
the Canadian standard ICES-003. Ce DEFR de la classe [A]
est conforme à la NMB-003 du Canada.

Note: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his

own expense.

• This luminaire is designed for outdoor lighting service,
and should not be used in areas of limited ventilation,
or in high ambient temperatures.

• Best results will be obtained if installed and maintained
according to the following recommendations.

• Luminaire is designed to operate in typical
temperatures at 25°C and to be mounted horizontally
with LEDs facing down, as shown.

imagination at work

SPECIFICATIONS

• Weight: Maximum weight XX lbs. (XXX kg)

• IP Rating: Wet location (IP66 for optical and electrical)

UNPACKING

1

• This luminaire has been properly packed so that no
parts should have been damaged during transit.

• Inspect to confirm.

HANDLING

2

• Damage may occur if luminaire is improperly handled
outside of pack.

• Do not impact or stack luminaire after removal from
packaging.

MOUNTING

3

WARNING

Risk of injury or damage. Unit will fall if not installed

properly. Follow installation instructions.

A. Before Installing:

1. Drill a 4” open hole in the ceiling to mount fixture. If the
size of open hole in the ceiling is less than 4”, enlarge
the open hole to 4”. (See Fig.1)

2. Clean all areas that will be sealed.

FIGURE 1

B.

Lift the luminaire to the 4” open hole. Pass wires or
cables through the ceiling. Do not pinch or trap wires
between luminaire and ceiling. (See Fig.2)

C.

Mount the luminaire using the provided hardware. Use
30in-lbs of torque for the mounting screws (do not over
tighten or strip screws). If ceiling material is 22ga or
lighter, an accessory backer plate is recommended.
(See Fig.3)

FIGURE 3

Electrical
A. From above, make electrical connections.

1. Connect power to luminaire where Black is Line, White
is Neutral and Green is Ground. Replace the electrical
access plate with gasket seated against fixture and
fasten with provided hardware. Use liquid tight fittings
(not supplied) to form a weather tight seal to luminaire.

2. If ordered with accessory junction box, mount the
junction box to the top of the fixture using provided
hardware, connect lead wires same as above. Replace
Junction box cover with all provided gaskets. Use liquid
tight fittings (not supplied) to form a weather tight seal
to luminaire.

Notes:

• This product must be installed in accordance with
applicable local, state, and national electrical codes
by a licensed person familiar with the construction
and operation of the product and hazards involved.

• This luminaire must adequately grounded for
protection against shock hazards and to assure
proper operation.

• Make sure all electrical power is turned off while
installing the fixture.

• If the supply wire is damaged, it must be replaced by
the manufacturer or its service agent or a similar
qualified person in order to avoid a hazard.

• The structure of Installation of this lighting needs to
afford load of 20 pounds. To avoid fixture fall.

• Fixture recommended installation height of 16 feet
or above.

FIGURE 2